Search Documents

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942

By Emory J. Douglass

Mining companies are unique in that they extract mineral resources and must therefore deal with ecological disturbances and other special problems. Like most enterprises, however, their primary motive must be to make money. The problem of mining investment starts with the question of what "make money" means. This article proposes an answer consistent with what economists call the theory of the firm and then applies it to two of the common, and perhaps unrecognized, problems connected with min¬ing investment. In essence, the concepts presented here call for thinking to terms of the income change associated with a given change it outlays or operating procedures To illustrate. ABC Distributing Co. has just discovered the power of advertising. It has raised its annual advertising budget from $25,000 to $50,000, and sales have, zoomed from 250.000 to 350,000 units. The company buy, for 50e per unit and sells at $l. This move has produced $50,000 of operating income for $25.000 in additional advertising expense. This looks great, so the next year the advertising budget goes up to $100,000. Sales go to 440,000 units. With 90,000 more units at 50[c] per unit, ABC sales are up by $45.000. Its advertising costs, however, went up $50,000.

Jan 1, 1971

By A. Springer

Chemists, physicists and others, whose occupations necessitate the use of fine scales, have heretofore regretted their inability to obtain any which would remain uniformly accurate. The difference between the theoretical and the actual results obtained in the ordinary balance (provided the pivot-distances are exact) is mainly due to the frictional resistance between the knifeedges and their bearings. This frictional resistance, although reduced to a minimum in the finest scales when new, constantly increases, thereby decreasing the sensitiveness proportionately. When examined under the microscope, neither the surface of the knife-edge nor that of' its hearings ever appears perfectly smooth. Soft kunife-edges are easily blunted, whereas hard ones are brittle and liable to crumble under the effects of over-load or shock. Prof. Frederick A. Roeder for many years attempted to discover some means by ,which the knife-edge could be replaced with some device free from the above-mentioned objections. His experiments convinced him that a torsion-joint was best suited for that purpose. After he had communicated his conclusion to me, we jointly developed the system to its present form. A torsion-wire had been used for the centre of rotation, prior to Prof. Roeder's invention, but it was found impossible to replace the terminal knife-edges with torsion-joints.

Jan 1, 1884

By W. E. Hubbard

The Panhandle area of northwest Texas embraces the northern portion of the Permian Basin of Texas as well as a considerable portion of the western part of the Anadarko Basin of Oklahoma. For the purpose of this report it will include in addition to the 20 counties of the Panhandle proper the two tiers of counties lying to the south, a total area of about 32,000 square miles. Crossing the Texas Panhandle diagonally from northwest to southeast is the Amarillo Arch, related to which is all of the production discovered to date. Oil Production Up to Jan. 1, 1930, the Panhandle has produced about 125,000,000 bbl. of oil. The peak yearly production occurred in 1927, during which period 49,000,000 bbl. were produced. In 1928 the production fell to 25,000,000 bbl., but in 1929, on account of important discoveries in Gray County, the total increased to 31,000,000 bbl. To date Hutchinson County has produced 64 per cent. of the total. Table 1 shows the total yearly production by counties. The present production of the Panhandle is 100,500 bbl. from 1745 wells or an average of 57.6 bbl. per well compared to a production on Jan. 1, 1929, of 59,748 bbl. from 1468 wells or an average of 40.7 bbl. per well. The peak production of the year occurred during the week

Jan 1, 1930

By Moshe Sheinkin, Burke O. Trafton

This paper describes the use of a computer in analyzing the expected return on a mining venture. The computer program is designed to incorporate all aspects of a mining project, including the mine, mill, smelter, and refinery. Data input may consist of the operating variables in each phase such as the mining rate, grades, reserves at the mine, and the technical operating characteristics of the mine, mill, smelter, and refinery. Detailed tax computations are shown for a domestic operating company, for a foreign company and for a foreign subsidiary. In addition, the use of the various options that are available such as expense write-offs or deferments to create tax credits during preproduction years are considered, and its effect on the DCF. The program is also constructed to accommodate changes in metal prices, and escalation of capital requirements and operating costs. Output consists of profit and loss statements for entire projects using different methods of depreciation, cash flows, discounted cash flows, net present value and returns on investment. Returns on investment are computed for equity investment, total investment, and total investment less tax credits. Allowances are made for bank and guaranteed loans. Additional financial statements can be made for the following: a) A mine-mill segment with a concentrate selling schedule b) A mine-mill-smelter complex with a smelter product selling schedule c) Profitability of the smelter separately d) Profitability of the refinery separately

Jan 1, 1969

By G. Gutierrez, M. C. Fuerstenau, J. D. Miller

The response of pure goethite and two natural iron ores to flotation with potassium octyl hydroxamate is presented. The ores contained 12.5% and 39.7% iron; concentrates containing 69.5% and 61.5% iron, respectively, were obtained with additions of 0.4 lb/ton hydroxamate. Selective flotation of iron oxides from associated gangue minerals has proven difficult in the past with standard collectors, such as sulfonates and fatty acids. As a result, recent work has been directed toward silica flotation with calcium activation after the iron oxide surfaces have been blinded with certain starches.& The results obtained with this technique are encouraging. This method, however, involves depressing a mineral that would normally float under the conditions employed. A preferable method would involve floating the iron oxide because quartz is naturally depressed until activated. Earlier work involved this approach, but in view of the results obtained, collectors that exhibit greater specificity for iron are needed. During an investigation of chrysocolla flotation with potassium octyl hydroxamate, a metal chelate former, it was observed that pyrite floated well with low additions of collector.3 This phenomenon suggests that hydroxamate has a rather strong affinity for iron, and that other iron-bearing minerals should also respond to flotation with octyl hydroxamate. The object of this paper is to determine this response. The experimental work was divided into areas, the first of which involved microflotation experiments with pure goethite with an apparatus described previously.4 Goethite was selected because of the ease

Jan 1, 1968

By E. S. Bardwell

TWENTY years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute, discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining. Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 lb. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper' has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness.

Jan 1, 1933

Oil-well driller with extensive experience in this line of work. Location, Bolivia, South America. Salary depends on experience. R.-789. Mining Engineer, with geological knowledge, who can locate suitable spots for drilling oil wells. Location, Bolivia, South America. Salary depends on man. R-788. Construction Engineer, mechanical or civil engineer with experience in installing oil plants for foreign field. Must be able to install entire equipment including tanks, piping, buildings, etc. Salary depends on experience. R-782. Geologist, competent petrographer for micropetrographic work and training of two assistant students under the direction of the Director of a Geological Institute. Engagement is for six months with option on the part of the Director for an equal period: Location, Mexico. Salary, 450 pesos Mexican gold ($225 per month). R-765. Operating Mechanical Electrical Engineer, with extensive experience in charge of the maintenance, repair, and betterment of all mechanical and electrical equipment on mining operations. Desirable that the man have had this experience in connection with phosphate mining. Applicant must be competent to direct shop repairs on motors and generators, including rewinding, the building and maintenance of transmission lines, etc. Must also have ample machine-shop experience to enable him to direct repairs of light locomotives, steam shovels, brown hoists, caterpillar tractors, and auto trucks. Duties will include the betterment and maintenance of phosphate-rock washers and rotary-work dryers. The applicant must also be competent to conduct efficiency tests on all such equipment and be enabled to interpret data collected. Splendid opportunity for the right type of man. Climate and living conditions excellent. The company will furnish house rent free, including light .and water. Location, Florida. Salary depends on experience. R-854.

Jan 7, 1919

By E. S. Machlin

RECENTLY, there has been much activity in the field of nucleation of martensitic transformations.'- One of the problems in this field is the calculation of the rate of nucleation (number of plates nucleated per unit untransformed volume per unit time) in terms of observable parameters. Two such observable parameters are the fraction of the length of a straight line which corresponds to the portion of the total length of the line that lies in the martensitic phase and the number of plates intersected by this straight line per unit length of line. Because of the necessity of a valid answer to this problem, the following investigation was undertaken. Although this problem has been treated in the past, a derivation of the relation between the volume and linear fractions of martensite will be described to illustrate the method used in the succeeding analyses. It is assumed that the martensitic plates are in the form of a right circular cylinder having a small height relative to the radius of the base. The volume fraction of martensite is then: fr = lXNl,hjAl [1] where f, is the volume fraction of martensite, and Nij is the number of plates per unit total volume having the area Ai and the height hi. The linear fraction of martensite is obtained as follows. For the plates having the particular area A, and height h,, the fraction sin 0 dB* will have their cylinder axes between the angles 0 and 0 + d0 to the straight line along which the linear fraction of mar-

Jan 1, 1953

The Engineering Index Service, 29 West 39th St , |New York, N Y. (A division of the American Society of Mechanical Engineers ) This Service is the most complete guide to engineering articles as they are published in current engineering literature of the world All branches of engineering are covered It is prepared on standard library filing cards which are mailed every week. Each card contains complete information as to the source of the article indexed and an annotation, or a description, in which there is sufficient information to enable one to select articles of particular interest. With this Service those interested in any phase of engineering may, with a minimum of time, keep in immediate touch with engineering developments throughout the world There are 225 divisions of the full Service, 31 deal directly with mining engineering, and 15 with metallurgical engineering Divisions may be subscribed to separately or in any desired combinations The cost depends upon the extent to which the Service is used Many divisions are priced at $7 a year. Complete information may be had upon request. A suggested mining engineering group of divisions only, follows Division 1, Abrasive industry, 17, Bituminous materials, 21, Brick industry; 33, Clay products industry, 35, Coal mining industry, 36, Coal preparation industry, 76, Fuel engineering, 78, Geology, 79, Geophysics, 82, Gypsum industry, 99, Insulating materials, 108, Lime and limestone products industry, 109, Liquid fuels, 111, Lubricants and lubrication; 122, Metal mining industry, 127, Mineralogy and rare metals and elements, 128, Mine safety and ventilation, 129, Mining engineering and mineral industry; 130, Mining geology; 136, Natural gas and gasoline industry; 141, Nonmetallic minerals industry, 143, Oil field operation, 146, Ore treatment, 151, Petroleum engineering and industry, 152, Petroleum geology; 153, Petroleum refining industry, 154, Petroleum

Jan 1, 1933

By H. H. Campbell

In the extending employment of open-hearth steel for structural purposes, it is a matter of prime importance that the test-piece shall represent with practical accuracy the characteristics of every portion of the heat from which it comes. In ordinary practice this homogeneity is assumed; but inasmuch as leading exponents of the revolving-hearth system have claimed that a reasonable uniformity could be obtained by their method alone, it may be pertinent to offer a few facts on the subject. The following heats made by the Pennsylvania Steel Company, for bridge-work, were tested by casting two four-inch ingots, one being taken during the first third and the other during the last third of the cast. Test-pieces obtained from these small ingots usually give results inferior to those obtained from larger sizes; but for purposes of cornparison they are equally conclusive. Many of the tests were made for experimental purposes within a few hours of the time of rolling, and before sufficient time had elapsed for the usual molecular redistribution necessary for the best results. All the tests were made on 3/4-inch rounds just as they left the rolls and without annealing; the results, therefore, are subject to the errors caused by variations in the diameter, and in the temperature at which the bar was finished. The tests from any one heat, however, were always nude as nearly as possible under the same conditions; and inasmuch as these data include the results of every heat so tested, and inasmuch as the errors could not by any chance always support any single theory, we may be certain that the unanimons testimony of the experiments indicates a valid conclusion.

Jan 1, 1886

By R. S. Hendricks

During the past two years, Hecla Mining Co. has used shotcrete for ground support purposes with substantial cost savings. Hecla's experience indicates that shotcrete is an extremely effective ground support material which can be successfully employed in problem areas where various conventional systems would fail. To date, Hecla's use of shotcrete has been limited to openings where long-term high-quality support was required, to specific areas where exceptionally difficult ground conditions were encountered [ ] and, occasionally, to stope support. It is anticipated that when the necessary engineering and procurement of the components of an efficient materials handling system have been accomplished, shotcrete will be used on a routine basis in stoping and development situations. The real future of shotcrete is based, however, on the fact that this form of support offers greater opportunity for mechanization than rock bolt, timber or steel. Unlike all other support operations, which are cyclic, shotcrete is a continuous process, and therein lies its potential for incorporation into an efficient rapid excavation system. Hecla has obtained and operated both wet- and dry-process shotcrete application equipment. The operational characteristics of the two processes are presented and discussed below.

Jan 1, 1970

By J. R. CAIN

SAMUEL L. HOYT, ? Nela Park, Cleveland, Ohio (written discussion?). The work that Dr. Cain is doing on gases in steel should have a highly important bearing on investigational work in connection with steel-making practice. We found, for example, in our work in connection with the use of manganese in open-hearth practice that we needed expressions for the manganese efficiency and the "condition" of the steel. To get these figures we assumed that we would need to know the amount of FeO at different stages of the heat and the amounts of the gases present. This required simultaneous analyses of our samples for FeO and the gases and Dr. Cain seems to be the only investigator who has considered the analytical work from this point of view. That he has done so is very encouraging and it is to be hoped that his work will solve the mys-teries now surrounding this neglected phase of steel metallurgy. Those interested in the Ledebur method for use in connection with the efficiency of manganese as a "deoxidizing " agent will he disappointed to learn that more recent work at the Bureau indicates that Ledebur determinations are not reliable. The principal source of error seems to be due to the partial reduction of the ferrous oxide by the carbon present in the steel. However, it seems like an unnecessary criticism of the Ledebur method to state (p. 1319) that it proved of little value because it showed little differences in oxygen for a series of steels treated with ,various reagents and showing variations in physical properties and free-

Jan 12, 1919

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

David H. Browne was born June 8, 1864; at Hollymount, County Mayo, Ireland. At the age of 16, after going through the Londonderry Academy; he came to this country, and entered the University of Michigan, where he was graduated in 1885. He began his scientific practice as chemist, under F. A. Emmerton, in the laboratory of the Joliet Steel Co., after which he served some time as chemist at the Ludington mine, Iron Mountain, Mich. But in 1888 he went back for a year to his alma mater as instructor in inorganic analysis. Those who knew him feel sure that he would have been an efficient and popular professor; but his ardent temperament could not brook the rnonotony and confinement of the class- room; and in 1899 he went to work at the Andrews and Hitchcock blast-furnaces, at Hubbard, Ohio, where he remained until 1891, when he entered as chemist the service of the newly organized Canadian Copper Co., operating in the Sudbury district, Canada. This was the beginning of his special professional life-work. For twenty-six years he devoted himself to the numerous and complex problems successively arising in connection with the metallurgical treatment of the nickel-copper ores of Sudbury. One of his notable achievements was the development of an electro-lytic process for the separation of nickel and copper in the ores referred to. This method was successfully employed for several years; but when the Canadian Copper Co. was absorbed by the International Nickel Co., the cheaper Orford process owned by the latter was substituted. . A still more permanently important piece of metallurgical progress credited to Mr. Browne was the successful firing of reverberatory smelting-furnaces with powdered coal-a measure which had been desired, dreamed and attempted by others, but which he was acknowledged as first to put in practice on a large scale. The Engineering and Mining Journal of April 7, 1917, says editorially of this improvement:

Jan 6, 1917

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordi-nary, nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investi-gation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may he mentioned here that nickel dissolving electrochemically and entering the electolyte pre-sents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed sepa-rately below.

Jan 1, 1938

0PINION was general that this year's meeting of the Institute of Metals Division was one of the best in its history. In addition to its full and exceptionally fine program of professional papers, there were several other features of general interest-an in-spiring annual lecture by Dr. Cecil H. Desch which appears in abstract elsewhere in this issue, Mr. Sing-master's talk on the zinc industry at the annual dinner, and the presentation of the James Douglas Medal to one of the members of the Division, Dr. Zay Jeffries. Four technical sessions of the Division were held, dealing respectively with zinc, copper, aluminum, and general metallography, and in addition there was a joint session with the Non-ferrous Metallurgical Committee of the Institute. All of the papers presented were at-tended with much interest and followed by considerable discussion. The papers on plastic deformation of zinc by Messrs. Mathewson and Phillips, Romig, and Hoyt were of particular interest and awakened an extended discus-sion. They well illustrated the progress which is being -made today in the understanding of the mechanism of flow of metals, and the ingenuity of the authors in their crystallographic method of attack of this difficult problem was quite generally admired. A very old subject was treated in a modern way by Messrs. Corson and Bain in two papers on the harden-ing of copper and copper alloys. There has always existed a myth that the ancient Egyptians were masters of an art not possessed by ourselves; viz., that of hard-ening copper. This myth must have been quite defi-nitely dispelled in the minds of all those who listened to this admirable paper. Mr. Corson has applied the modern art of precipitation hardening to this old prob-lem with substantial success, employing small amounts of chromium, nickel, silicon, and cobalt for this purpose. The commercial application of these very important .developments of Mr. Corson is being actively investi-gated at the present time.

Jan 3, 1927

By John Mathews

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from ;shrink holes, cold sets, .pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to, consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.-The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the "set," or the detail appearance of the surface of the shape (the wave-like struc-

Jan 2, 1920

By J. S. Miller

THIS paper describes the method of mining a steeply pitching anthracite seam on a heavy pitch in the Orchard vein in No. 1 Tunnel of the Lehigh Coal and Navigation Co. The Orchard vein in the Nesquehoning district has a thickness of about 15 ft. on the level of the gangway, which is sufficient thickness for the gangway to be driven full width in coal. Above the gangway, the vein becomes thinner and near the surface is about 8 ft. thick. The coal is of good hard quality and carries a fairly good roof. The pitch of the vein is between 65° and 70°. Usually the breast-and-pillar method has been employed in the mining of the steeply pitching veins in this section. This method produced good results as far as the mining of the breast was concerned but the recovery of the pillar was difficult as to full extraction and expensive as regards costs. To recover these pillars after the breasts were driven, three methods were commonly employed; they were known as the pillar-breast method, pillar-skipping method, and pillar-chute method. The pillar-breast method consisted in putting a battery in one corner of the pillar (Fig. 1), coupling the manways A and B of the two adjacent breasts for two or three lengths ahead of the working face of the pillar being cut, and working the pillar as a breast. This method was used by the more skilled miners of the earlier days but has practically been abandoned. A slight variation of this method is used to some extent. In this case, the pillars are left wider than ordinarily and of sufficient width for the full-width breast to be driven in and a small pillar left on each side of the pillar breast between it and the regular breasts. With the completion of the "pillar breast," the ribs are drilled full of holes, loaded, and fired.

Jan 3, 1925