Search Documents

By Alan B. Nicol, W. T. Parry

The outcome of these tests has been twofold. They have served to demonstrate that the tiltmeter is a useful and dependable instrument which could prove to be of significant value in reaching the goals of landslide prediction and control, and they have raised a good many more questions about the mechanism of slides than they have answered. It seems likely that many of the old concepts and assumptions will be modified or discarded as more knowledge of actual field phenomenon is gained. Safety and economy are paramount concerns in determining slope stability. These two considerations govern the feasibility and character of slope construction from start to finish.

Jan 1, 1970

By Douglas A. Blankenship, Randall G. Stickney

The corejacking test is a field test designed to measure the response of salt to known boundary conditions. A 1.0-m-diameter salt core is externally pressurized using curved flatjacks placed in the annulus surrounding the core. Time-dependent deformation of the salt is measured by monitoring the diametrical closure of an inner borehole. A finite element elastic analysis of the jack loading system has been performed. The purpose of this analysis was to determine if the original assumption of axisymmetric loading is correct. Six loading cases were investigated, each representing either hypothetical or previously encountered jack configurations.

Jan 1, 1982

The Army Reorganization Act, which became effective July 1, 1916, contains a provision authorizing the organization of an Officers' Reserve, in which will be included a Corps of Reserve Engineers. There will also be an Enlisted Reserve of skilled workmen in technical lines. The special provisions of the bill relating to the Engineer Officers' Reserve were formulated with the help of the Joint Committee of the several national engineering societies, which has been at work on the matter for over a year with the War Department and Committees of Congress. Recognizing that engineering science is the basis of success in modern

Jan 8, 1916

Scores of visitors who had never in their lives seen a piece of rough-and-ready mining machinery flocked around the display of Russian equipment presented as part of the Soviet Exhibition at New York's Coliseum. The Russian show, which ran from June 30 to August 10, presented an impressive view of an emerging technology. The exhibitors, however, made little attempt to appeal to the visitor who came only to be amused. In the mining show, as well as elsewhere throughout the exposition, the exhibits were devastatingly highbrow. If a coal mine's hydraulic roof support were "designed to support the prop- , free face front in longwall faces of flat seams, from 1.0 to 1.6 m thick, with medium-stable side rock," the visitors were told just that.

Jan 9, 1959

By Horace Pops, J. F. Libsch

THE discovery of SAP alloys (sintered aluminum powders) by lrmannl has stimulated investigations in other alloy systems.23 Not only do such alloys have good room-temperature properties, but they maintain high strength after prolonged service at elevated temperatures. In addition, they show high structural stability, including unusually high recrystallization temperatures. These characteristics are secured by dispersion hardening. For this investigation, Zn-ZnO alloys were selected. Practically, the fact that commercially pure zinc recrystallizes near room temperature prohibits strengthening and hardening by cold deformation and therefore limits the application of zinc where mechanical strength is important. Similarly, the poor

Jan 1, 1961

Improvement of drilling operations through the development of new, unconventional drill bits is a prime research target at Sandia Laboratories, Albuquerque, N.M. Sandia is currently focusing efforts on four new bit designs which its engineers believe may eventually improve penetration and reduce operating costs. The Energy Research and Development Administration (ERDA) has budgeted $500,000 in support of this program to date. Two of the drill bits-one that chips rock with high voltage spark discharges, and another which fires small projectiles into the rock ahead of a regular roller bit-are designed to increase both penetration rates and downhole bit life.

Jan 8, 1975

By K. S. Choi, B. S. Shin

The adsorption characteristics of sodium silicate on scheelite, calcite, and fluorite minerals were investigated. Adsorption equilibrium took about 60 minutes. Adsorption data show that the masimum amounts of adsorption of sodium silicate occurs at about pH 9.8. The adsorptivity was in the order of calcite > fluorite > scheelite. The amount of adsorption of sodium silicate increased with the increase in temperature of sodium silicate solutions. The amount of adsorption of sodium silicate decreases in the low concentration range of ferrous sulfate, while in the high concentration range of ferrous sulfate, the adsorption of sodium silicate increases.

Jan 1, 1986

By H. Rush Spedden

When Robert H. Richards wrote Ore Dressing, the famous four-volume work published in the first decade of this century, the ore dresser was still largely concerned, with the mechanical treatment of ores. Since then, however, economics have transformed him into a mineral processing engineer who must increasingly deal with closely integrated facilities designed to produce a commodity for manufacturing. Moreover, this change will grow marked as the complex low- grade ores of the future make it ever more necessary for him not only to use the best combination of pyrometallurgical, hydrometallurgical and physical separation processes, but also to integrate these processes at the mine site. Nor are economic pressures the only ones propelling the processing engineer into a new era. The ecology drive has thrown him into a new situation in which his economic base is radically altered, and it could well precipitate as drastic a revolution in his technology as that which took place when flotation was developed.

Jan 1, 1971

By G. C. Hewett

This portion of the State, being the northern half of its Pacific slope, is drained by four rivers, the Gunnison, Grand, White and Yampa or Bear, which, with the Green, flowing south from Wyoming, unite to form the Colorado. These streams, fed by the snows of the Rocky Mountains, fall from an altitude of 10,000 to 12,000 feet, at their sources, to 4000 feet, at the confluence of the Grand and Green in Utah, near the State line. This area, about 150 miles square, was the scene of great development in the periods subsequent to the Carboniferous; but earlier

Jan 1, 1889

By Ta M. Li

The implementation of the Clean Air Act (CAA) Amendments of 1970 has resulted in a clean fuels deficit that has significant adverse environmental, energy and economic implications, according to the Project Independence Report. The CAA Amendments charge the Environmental Protection Agency (EPA) to establish national air quality standards as well as national standards for significant new pollution sources and for all facilities emitting hazardous substance. Section 110 of the CAA provides the framework for states to establish "emission limitations, schedules, and timetables for compliance with such limitations, and such other measures as may be necessary to insure attainment and maintenance" of ambient air quality standards. State implementation plans (SIP) are subject to EPA approval. EPA is authorized to enforce federal and state requirements by order or civil suit, including injunctive relief.

Jan 5, 1975

The 114th (New York) Meeting of the Institute will be held in the third week of February, 1917. The Committee on Papers and Publications has set Dec: 1, 1916; as the closing date for the receipt of manuscripts intended for this meeting. Manuscripts must be received by the Secretary on or before this date. If they are sent through members of the technical committee they must be sent to those committees enough in advance of the time to be forwarded and in the hands of the Secretary by the time specified. While Dec. 1, 1916, is the final closing date, it is a great advantage to get papers in as much before that time as possible as it enables them to be submitted in proof form to their authors. Papers received on or before Nov. 1, 1916, will, as far as possible, be published in the January Bulletin or earlier, thus giving good distribution among the members in advance of tile meeting. The Institute's records show that the discussion of papers is very rnuch better when they are distributed somewhat in advance of the meeting instead of in the Bulletin which goes out immediately preceding the meeting.

Jan 9, 1916

By Daniel C. McLean

Copper concentrates produced by many operations in the United States and South America contain chalcocite (79.9% Cu) as a major component, yet the grades of these concentrates rarely exceed 25 to 28% Cu. Mineralogical studies made by E.P. Cadwell indicated that the low grades were caused by dilution by pyrite rimmed with secondary chalcocite. Laboratory and plant tests proved that concentrates could be significantly upgraded by using a simple, low cost cyanide leaching technique to dissolve the rims and reject the pyrite. The many advantages of this new procedure are cited and the process steps and a typical flowsheet are described.

Jan 1, 1984

By W. V. Vietti

Actual field data from several wells are used to illustrate the application of the method of determining the average density of the fluid column in a flowing oil well in the Yates field, Pecos County, Texas. The depths of the wells in the Yates field vary from 900 to 1700 ft., depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. per hour have been determined and many wells are capable of producing 2000 bbl. hourly. Gas-oil ratios are usually below 400 cu. ft. per barrel, but a few wells high on structure have produced over 3000 cu. ft. per barrel. Incidentally, tubing wells has cut these high ratios to as low as 400 cu. ft.' By common agreement of the operators all wells making ratios over 400 cu. ft. will be tubed. Daily production of the field is prorated to 110,000 bbl. from an open-flow potential of 5,000,000 bbl. based on hourly open-flow gages.

Jan 1, 1931

By E. S. Moffat

Members of the Institute who have visited the works of the Lackawanna Iron and Coal Company at Scranton, will remember the exposure of a large vein of anthracite coal in the rocky bank on the south side of Roaring Brook, near the blast-furnace. The vein is quite flat, and is exposed to view for several hundred yards along the banks of the brook, a few feet above the surface of the water. It is some ten feet in thickness, and is known as the Big Vein. At a point just opposite the blast-furnace, much of the coal from this vein was mined out many years since, the usual pillars being left to support the overlying rock and drift, which are here some twentyfive to thirty feet in thickness. Over thirty pears ago fire was communicated from an ore-roasting pile on the surface of the ground at this point, through an old shaft, down to the refuse and pillars which had been left in the mine

Jan 1, 1887

THE ladle is a small hearth made on a cage of iron bars like a bird-cage, and has a handle so that it can easily be taken from the forge and carried wherever desired. It is a common device and is much used among masters for small castings, but with a large weight you would have difficulty in lifting it by hand even though you were aided by levers and winches. If you should indeed do it, it would be just as if you had lifted the aforesaid hearth by force, and this would be unwise if you could do anything less difficult. A forge is likewise made for this, with a good pair of large bellows that are well covered with cloth. When the small hearth has been made with good clay, baked, and well covered with ashes, it is placed in front of the mouth [of the bellows] and a crown of two or three brick ends is built around it on top of the rim so that the charcoal may be held better and in greater quantity. Then, having lit the fire and heated the ladle and the charcoal, the pieces of material that you wish to melt are gradually put on

Jan 1, 1942

By Dale C. Matthews, Donald L. Simpson

Hecla Mining Company's Lakeshore Mine and Metallurgical complex near Casa Grande, Arizona, is the first plant in North America to utilize the roast/leach/electrowinning process for production of cathode copper from sulfide concentrates. Oxide copper ores are also mined at Lakeshore. Using sulfuric acid and sponge iron by-products of the roast/leach operation, the oxide ore is leached in vats, the copper is precipitated with iron and recovered as cement copper. This paper will describe the roast/leach facilities and discuss the operating conditions at which more than 95 percent of the copper in concentrate is made soluble in acid solutions while less than 5 percent of the iron is rendered soluble. More than 97 percent of the sulfur contained in concentrate is captured either as strong sulfuric acid or as soluble sulfates in leach liquors. The iron rich residue after leaching is pelletized and reduced to sponge iron in an SLRN reduction kiln.

Jan 1, 1981

INTRODUCTION TO STATISTICS It is necessary now to digress from the direct study of appraisal techniques to consider an important tool for the mineral appraiser. Whenever a great deal of data have been accumulated, such as might be gained through the sampling process discussed in the preceding chapter, the application of statistical methods should be considered. Statistical methods are used for descriptive purposes and for the organization and summarization of quantitative or numerical data. Descriptive statistics covers the tabulation of data, its presentation in graphical or pictorial form, and the calculation of its several descriptive measures. It is not the intent of the brief summary of statistics that will be outlined hereafter to cover the total breadth and scope of mathematical statistics. It is the intent of this and the following chapters to review a few of the statistical concepts that have the most direct bearing upon the problems involved in mineral evaluation. Should the reader desire to go more fully into statistical theory and mathematics, numerous texts and publications are available.

Jan 1, 1980

Robert H. Richards, Boston, Mass.: Mr. Goodale calls attention to the difficulty of obtaining clean tailings from the jigs which are fed by the spigots of the hydraulic separator. This difficulty is universally encountered. The Lake Superior copper mills practically overcome it by running the beds of those jigs loose, carrying into the hutch all of the available copper and some sand. These hutches are again jigged upon threesieve Collom jigs, where the treatment is very slow and gentle; and on the successive jigs lighter and lighter bedding is used. The last sieve is run thin enough to let some sand into the hutch. With these precautions most of the free copper is extracted, as well as a fair proportion of the included copper.

Jan 1, 1897

By G. L. Jr. Spencer

THERE is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least, only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiffness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges.

Jan 1, 1931

By M. B. Standing, D. L. Katz

Density data are reported on 15 saturated hydrocarbon liquids in the range of 35° to 250°F. and 1000 to 8220 lb. per sq. in. The apparent liquid densities of methane and ethane are shown to vary with the density of the system in which they are present. A method is proposed whereby the densities of liquid hydro- carbon mixtures containing both methane and ethane in solution may be computed at elevated temperature and pressures within the accuracy of usual engineering computations. A method of computing the shrinkage of crude oils based upon the gas-oil ratio, gas analysis, and crude gravity is outlined. Introduction The densities of naturally occurring liquid hydrocarbon mixtures are important in many petroleum engineering computations. Calculation of the shrinkage of a subsurface sample of crude oil as the natural gas is evolved is one example of the use of liquid-density data. Sage, Hicks, and Lacey5 have presented a method of computing the density of hydrocarbon liquid mixtures based on partial molal volumes. Katzl has indicated a method based on the principle of additive

Jan 1, 1942