Search Documents

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By S. S. Deshmukh

An important element of evaluating a materials- handling system by simulation lies in being able to examine the details of the proposed operation in a fashion which closely approximates real behavior. The added factor of flexibility permits including or deleting those parts of the problem which can be shown to be important or trivial. Used carefully, simulation can match manpower and equipment far more efficiently than conventional calculations. The same is true of interacting equipment systems. This efficiency results from being able to simulate the real fluctuations in a system by using empirical probability distributions compiled from existing operations. Simulation eliminates guessing as to efficiency, absenteeism, bunching, and the broad host of delays that influence productivity and substitutes operating data in place of the usual factors. In this respect, simulation improves detail and confidence in the reliability of engineering estimates.

Jan 1, 1970

By Harry A. Perry

The Highlad underground uranium mine is located in the southern Powder River Basin, Converse County, Wyoming. Development by Exxon Minerals Company began in 1973 and average production from the complex roll- front deposit ranges from 500 to 600 stpd. A staff of six eight grade control technicians work within the Geology Department to guide and monitor production, to minimize waste and to account production to reserve estimates. A thorough knowledge of the complex roll- front deposit aids in accounting production to reserve estimates. Grade control technicians assist the mine geologist in making geologic cross sections, in estimating reserves, and in predicting monthly and quarterly production grades.

Jan 1, 1980

By K. L. Woodruff

The first step in processing municipal solid waste (MSW), principally household waste, for resource recovery is usually shredding. A trommel has been investigated as a step to precede shredding. This way abrasive inorganic materials, such as stones and metals, would be removed prior to shredding, thus lowering the amount of feed and hence maintenance on the shredder. In addition, friable materials such as glass would be removed in large pieces, rather than pulverized too mall to process for recovery. The utility of a trommel for these purposes was investigated on a pilot scale using a unit 9 ft diam by 10 ft long with 4-in. square clear openings. Experimental results indicate that up to approximately half of the MSW may be removed as -4-in. material prior to shredding. The -4-in. fraction contains approximately 70% of the metals and 95% of the glass present in the MSW feed to the unit. Scale-up and cost information necessary for the design of a 60 to 70 tph unit is developed.

Jan 1, 1977

By H. M. Chance

WITHIN the last 10 years the subject of mine taxation in its relation to coal-mining interests has come to have growing importance, not only to those engaged in the mining of coal, but also to the owners of land underlain by coal. A disposition has developed among legislators to accept the principle, which has been laid down y many judicial decisions, that coal underlying the surface must be regarded as a part of the real value of all properties so underlain, and as such is chargeable with such burdens of taxation as the necessities of the government may impose. These necessities arise from the normal expense of maintaining State and local governments, and in the past have been met principally by, taxes based upon assessments of real estate values, which values in many cases have been confined principally or wholly to the value of the surface, without taking into consideration the value of minerals underlying the surface. It is not proposed here to deal with the question of Federal taxation, whether levied on production, or on products transported from one State to another, or exported from the country, or upon thegross or net earnings of corporations engaged in interstate commerce, or upon the production of materials which may be transported from one State to another, or levied. upon the profits or upon the obligations of corporations. The present discussion will be confined to the appraisal of coal lands as assessed for State, county, township, or borough taxation. The methods heretofore and at present in use in the different States vary widely and have resulted in more or less litigation. Discussions appearing from time to time in the technical and trade journals and in the proceedings of mining and engineering associations frequently direct attention to the need for the adoption of fixed principle in levying taxes, and of uniform methods for applying such principles, but there does not seem to be a general demand from the public for the adoption of such methods.

Jan 7, 1914

By John Birkinbine

The early history of the mining and metallurgical industries of Pennsylvania is so intimately associated with the section of the State in which we meet, that a brief resume of a few of the important historical facts, and a reference to some of the more modern enterprises, in which members of the Institute have been largely concerned, seem appropriate to this occasion. It is just two hundred years since the publication of the earliest mention of the manufacture of iron in Pennsylvania. What kind of iron this was, or where or by whom it was produced, is uncertain. The only record of it is the following verse, quoted in the admirable work of Mr. James M. Swank,* from a poem published in 1692: " A certain place here is, where some begun To try some Mettle, and have made it run, Wherein was Iron absolutely found, At once was known about some Forty Pound." One who stood one hundred and seventy years ago on the summit of this Neversink Mountain † (had the atmospheric conditions been favorable, and the timber somewhat removed) might have noticed in the daytime the smoke, or at night the reflection, from the fires of the first successful Pennsylvania iron enterprises, scarcely 15 miles to the south, viz.: Rutter's bloomary forge, built in 1716, and the Colebrookdale blast-furnace erected in 1720, respectively 3 and 8 miles distant from Pottstown. Here the pioneers of iron production in the State which has so long led, and still leads all others in this manufacture, had their trials and successes ; and it may be a satisfaction to some who bewail a present depression in trade, and the low prices now ruling, to recall the fact that in 1731 pig-iron is reported to have been sold ''in large quantities" at the Colebrook-

Jan 1, 1893

By W. D. Faulkner, J. E. Urbanic, R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in carbon-in-pulp and carbon-in-leach circuits has been investigated. Carbons from two US mines, one Canadian mine, and a South African pilot plant operation were characterized before and after regeneration. Thermal regeneration of the carbon was investigated using factorial analysis to determine the effect of interaction of furnace temperature, retention time, and use of supplemental steam. The operation of acid washing the service carbon was investigated, including a comparison of the use of nitric and hydrochloric acids. The effect of quenching regenerated carbon was also briefly studied. Prom the data obtained, guidelines are given for effective regeneration operation.

Jan 1, 1986

By A. Patton

E. T. McCLEARY, Youngstown, Ohio (written discussion).-Perhaps there is no question before the steel manufacturers of America today that causes them more worry than that of maximum production, together with good quality, and Messrs. Patton and Speller have clearly shown in their excellent paper how this may be accomplished. Any operation that tends to uniformity is certainly conducive to good practice, and as the use of roll scale in the converter eliminates to a large extent the variations in temperature due to varying silicon content in the pig iron, it should certainly give a more uniform product. At the plant of The Youngstown Sheet & Tube Co. the use of roll scale was started in the year 1908. A great many tests have been con-

Jan 4, 1917

By E. Tulcanaza

The practical significance of the in situ grade variability is usually neglected. Although recognized, often times it is either ignored or just considered as a vague guideline in many of the decisions dealing with exploration, reserve estimation, and mine planning. This paper stresses the significance of grade variability for exploration and mining, and illustrates its liaison to the structural features of the ore deposits, as well as to the mining parameters used for mine extraction. Some geostatistical results obtained from a silver mine, tungsten mine, and copper mine in South America are discussed.

Jan 1, 1985

By R. E. Allen

One of the most unusual oil-field engineering accomplishments of the past two years is the development and rapid advance in the directed drilling of wells. Directed drilling as referred to herein is the controlled steering of the drill stem in the required direction to a given location in the oil sand. The deliberate drifting of holes is an act so far removed from what has been considered good drilling practice that all of the old questions of correlation, drillability and production difficulties are revived. Only a few years ago, during the boom days of Seminole and Santa Fé Springs, the crooked-hole problem, as it was then called, occupied a primary position among the topics of the day in the fields of California and the Mid-Continent. The net result of all the discussion and study at that time was the conclusion that oil wells should be drilled with as little deviation from the vertical as possible and that crooked holes with elbows and dog legs were to be avoided because of the drilling and producing difficulties encountered therein, but that many nonvertical holes were slanting or angling rather than crooked and were not a serious problem.

Jan 1, 1934

By Richard Conkling

A SHALE layer, buried beneath two or three thousand feet of strata, in some instances, will upon folding become thicker in the synclines and thinner on top of the anticlines. This can be accounted for, in part, by the stretching on the crests of the fold and the compressing in the troughs; but this will by no, means account for all of it, as is shown in the example herein set forth. It is my firm belief that the rest of the thickness is due to flow. What causes the movement, however, does not concern us here, so long as there is movement, for this article purposes to show its effect upon the producing area of different sands. It is the author's hope, in this way, to drop a hint or two that may be valuable to the oil geologist, in making estimates of future productions and values of oil properties. An example will be given from property in the famous Cushing Pool in northeastern Oklahoma, where the author has had occasion to make a detailed study before recommending some property to his company, and has then been able to watch the results of this work. The author never mapped the surface structure in this pool, as this had been done by Frank Buttram when he was with the Oklahoma Geological Survey. We are using, therefore, a section of his map in this article for our surface contours. The main east clip comes farther east than this section shows.

Jan 10, 1916

By Roy Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant develop-ment work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduc-tion plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hun-dred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

US 4,185,872-In the solution mining of uranium values from a subterranean uranium ore deposit, a lixiviant comprising sodium sulfate or other alkali metal sulfate and optionally minor proportions of an alkali metal carbonate or bicarbonate and an alkali metal hypochlorite is introduced into the ore to solubilize uranium therein. The pregnant lixiviant is recovered for processing. E.T. Habib, Jr., assigned to Mobil Oil Corp. Jan. 29, 1980. 5 pp (299-4). Filed- 8-18-78 (934,933).

Jan 1, 1982

By Frank M. Stephens, Robert D. Macdonald

As processes for handling low-grade or complex ores become more complicated and as new methods are found, the need arises for more complete and detailed pilot-plant studies to protect the capital investment required for a full-scale plant. Occasionally a process is firm technically, but there is a need for a demonstration plant that will convince nontechnical men of the wisdom of investing in a full-scale operation.

Jan 5, 1959

SUGGESTIONS that existing schools give instruction bearing on the mineral industry, or that schools for that purpose should be established in the United States, began to be made early, and it would require too much space to catalogue them all. Some of the more important may be mentioned to indicate their general character. In the "advertisement to such parents as have now (or expect to have) children prepared to be educated in the College of New York," which appeared in the New York Mercury of June 3, 1754, Samuel Johnson, the first president of King's College, the predecessor of Columbia, said that it was the "design of this college to instruct and perfect the youth," among other things, "in the arts of Numbering and Measuring of Surveying, and Navigation and Geography. . . . and in the Air, Water and Earth around us, and the various kinds of Meteors, Stones, Mines and Minerals, Plants and Animals; and in the knowledge of all Nature in the Heavens above us, and of everything useful for the Comfort, Convenience and the Elegance of Life . . . " Though the concept that natural science should be used to enlarge the bounds of human life was thus implicit at Columbia from the , very beginning (John Stevens graduated from it in 1768, James Renwick in 1807, Horatio Allen in 1833, and A. W. Craven in 1899), it was only during the period of Renwick's professorship of Natural and Experimental Philosophy and Chemistry (1830- 1853) that much attention was given to applied science.* Among the Austin papers, published by the American Historical Association,~ there is a draft in Stephen F. Austin's handwriting of a proposed memorial from the legislature of , Missouri to Congress, not only urging "the propriety and utility * See chapter 4 for early interest in this subject in Philadelphia.

Jan 1, 1941

DESPITE the very small number of engineers who can get away from their tasks to New York, a point so far from the Mid-Continent and Cali-fornia oil fields, where the real important, engineering progress in the industry is being made, the attendance was remarkably good, and it was generally remarked that all the sessions were "snappy," and there was no drag. This was largely because, under instructions from the chairman, very few papers were permitted to be read, and the "high lights" of each paper were pre-sented orally as an introduction to the large and varied discussions, many of which were prepared in advance. The round table discussion on petroleum engineering research problems, conducted by W. E. Wrather, proved a greater success than was anticipated, considering the difficulty in getting many of the men to discuss such problems. There has been no crystallization of opinion heretofore of what are important engineering research problems, as distinguished from pure science problems, and a digest of the discussion will be made available so as to present the results obtained. It is hoped that further round table discussions, as well as committee work, in the meantime summarizing problems appear-ing in papers published the last two to three years, will enable the oil industry to determine intelligently which of the problems are most important for immediate attack. The roundtable discussion on petroleum engineering educational problems, conducted by H. C. George of the University of Oklahoma, was equally fruitful, and since managers of companies, consulting engineers, and pro-fessors cooperated in these sessions, a cross-section of their opinions on improving the curricula for training the large number of petroleum engineers, which the industry can absorb in-the next few years, was obtained.

Jan 3, 1927

By Y. J. Wang

A graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves is described. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and used as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1986

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

Jan 1, 1942