Search Documents

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By Dr. Hermann Wedding

Albert Ludwig Serlo was born February 14, 1824, at Crossen-on-the-Oder. After completing his school-studies and his training as a mining official, he received in 1851 an appointment as Royal Manager of salt-works (Salinenfactor) and member of the Administratioll of Salines at Konigsborn, near Unna, Westphalia. The issue of new regulations for the training of higher State officials in the Department of Mining, Metallurgy and Salines, led him to pass in 1856 a special examination for the rank of Assessor, in consequence of which he was called to Berlin, to serve for a few months as an assistant in the Ministry of Commerce, which had charge of mining, etc. In the same year he became Bergmeister and member of the mining administration at Bochum, Westphalia, and in 1858 Oberbergrath and member of the provincial administration, called the Oberbergamt, having its headquarters located at Dortmund. In 1861 he was appointed Director and head of the newly-reorganized mining

Jan 1, 1900

By Lawrence Addicks

Discussion of the paper of LAWRENCE ADDICKS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1471 to 1484. L. D. RICKETTS, New York, N. Y.--In the Southwest we have stored up millions of tons of tailings in which the copper exists partly as sulphide and partly in an oxidized condition. Mr. Addicks' first paper suggests a, likely process for the treatment of such material. His second paper 1 deals with the recovery of copper from clear solutions of notable strength, and such solutions may come from the sulphating roast or direct from the leaching of completely oxidized copper ores of which vast deposits are known to exist. What strikes me particularly about the latter paper is the keen perception shown and the clear manner in which the writer has attacked the fundamental principles of the process. He calls your attention to the fact that ferrous sulphate is necessary in the electrolyte and is an ideal depolarizer; that sulphurous acid must be, used to reduce the ferric sulphate produced and thus prevent re-solution of copper at the cathode; that mechanical agitation in the cell, in order to bring the ferrous sulphate in contact with the anode and the copper in contact with the cathode, is essential to efficient work; that lead anodes are

Jan 12, 1915

Jan 1, 1931

By William Kelly

An extensive swamp covers a large part of the town-site of Norway and adjacent laud. Through this swamp run two parallel oreformations. In the north one is the Aragon mine. The south one passes into the swamp on the Harrison property. On the edge of the swamp, about 1000 feet from the Aragon mine, a diamond drill, in the fall of 1889, located the ore-bearing formation and a probable ore-body. To explore further and develop this ore, the Penn Iron Mining Company proposed, in the spring of 1890, to sink a shaft. The drill had shown the depth of the glacial drift to be more than 60 feet. A test-pit near the location of the proposed shaft had struck, at a depth of 20 feet, an amount of water which a 200gallon pump was unable to lower. At the Aragon, a few years before, a shaft had been sunk to hard pan with great difficulty and many delays by the usual method of driving laths. Under the conditions it was decided to sink a caisson- or dropshaft. Two 40-horse-power boilers, a Lidgerwood engine with 4foot drum, and a good derrick were set up; and two No. 10 Kuowles

Jan 1, 1892

Jan 1, 1970

New Products Equipment

Jan 7, 1953

Jan 1, 1928

Redetermination of the Chromium and Nickel Solvuses in the Chromium-Nickel System by C. J. Bechtold and H. C. Vacher, p. 14 The text of pages 16 and 17 is in improper sequence. The correct version will appear in the bound volume.

Jan 1, 1962

By R. T. Hukki

BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that [ ] Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate).

Jan 6, 1954

By Edward Judd

CONSTRUCTION of the long projected Moffat tunnel, on the Denver & Salt Lake R. R., between Tolland and Irving, Colorado, is now actually and actively progressing. This 6.1-mile bore through the Rocky Mountains, at an elevation of about 9200 ft., will eliminate 33 1/3 miles of probably the most tortuous standard-gage track in the world, and at the same time will avoid the necessity for crawling over the snow-bound continental divide at an elevation of 11,660 ft Completion of the tunnel within the stipu-lated four years, is expected to nave an immediate effect on the develop-ment of the known coal fields in north-western Colorado, already penetrated at Craig, the present terminus of the road, while it will also enable the railroad to carry out the original designs of its founder, David H. Moffat, for through traffic from farther west. The intention now is to accomplish the latter object by an extension from McCoy following the canon of the Grand River down to a connection with the Denver & Rio Grande at Dotsero. Legal impediments to the financ-ing of the tunnel having been removed by action of the Colorado legislature in April, 1922, the Moffat Tunnel Improvement District issued bonds to the amount of $6,720,000 which have been widely and quickly distrib-uted through a New York banking house. Responsi-bility for the execution of the project has been vested in the Moffat Tunnel Commission, to which a board of consulting engineers has been appointed for carrying out the details of administration. This board includes D. W. Brunton and L. D. Blauvelt, of Colorado, and J. Vipond Davies and J. Waldo Smith, of New York; R. H. Keays, who has managed large tunnel projects in New York, is chief engineer for the Commission.

Jan 11, 1923

By Arthur L. Bishop

INTRODUCTION Purpose The in-situ leach method for uranium extraction is a relatively new and innovative method of uranium mining. In 1975, the first commercial in-situ facility began operation in south Texas. Since that time numerous other operations have been initiated as either pilot or commercial ventures. Considerable literature has been published that deals primarily with generalities of the process or environmental concerns. Several federal agencies have published documents which do not reflect the true operating or environmental nature of the in-situ leach method of uranium extraction. From an environmental standpoint, this is also evident in the promulgation of rules and regulations. Hence, the purpose of this paper is to present experience with an environmental concern--non- production zone excursions--such that the industry and the regulatory agencies will gain greater insight devoid of preconceived ideas and misconceptions. General Process Description In south Texas, in-situ leach mining is utilized to extract uranium from permeable sandstone ore deposits 61 to 213 meters (200 to 700 feet) below the surface. Uranium is present as an insoluble uranium oxide. In the in-situ or solution mining technique, anoxidizing lixiviant is injected into the formation through injection wells. The solution reacts with the insol uble carbonate complex. This soluble uranium complex is produced at recovery wells, each containing a submersible pump. During production there is a constant sweeping of lixiviant through the formation from the injection wells to the recovery wells. Injection and recovery wells can be arranged in any of a number of geometric patterns dependent upon ore body configuration, aquifer permeability, and operator preference. Submersible pumps in the recovery wells pump the uranium rich pregnant solution to the initial processing facility. Monitor wells surrcsund the pattern area and are screened in appropriate stratigraphic horizons (production and non-production zones) to detect any lixiviant migration that may occur (Fig. 1).

Jan 1, 1980

By John D. Vincent, Howard W. Jacky

This chapter covers the normal problems encountered in the building of an ore concentrating facility. To produce such a facility In today's environment requires correlation by the engineers involved of geologic data, mine planning, scheduling, future planning, water resources, power, land availability, testing, design, start-up and environmental considerations. Of course, the program scheduling and character of the ore will determine the weight given to the above considerations in the final design and construction of the plant.

Jan 1, 1978

By James Boyd

All mining and milling enterprises must be based on adequate ore reserves. Reserves must be established by physical exploration, and the orebody should be of sufficient size and grade to insure recovery of capital invested in mine purchase, development, and mill construction and to provide a reasonable profit. Determination of these economic factors is so complicated, and present costs of mine development and construction so great, that analysis can be made only by competent persons qualified by experience in this field. What rate for maximum efficiency? Unfortunately, even today mills are built before deposits have been adequately outlined, and there are rusting monuments to such folly in nearly every mining region. Also there is a tendency to be guided by the philosophy that "if a little is good, a lot is better," which leads to the conclusion that mining at a given rate and making so much per ton will yield a profit of so many dollars per day. Consequently, why not build a mill to treat twice as much per day and make twice as much money?

Jun 1, 1956

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting- the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No.1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

Frank Firmstone was born Aug. 29, 1846, at Glendon Iron Works, near Easton, Pa., the residence of his father, William Firmstone, one of the pioneers of the anthracite-iron business. After preliminary school education at Easton, Pa., he attended the Saunders Military Academy in Philadelphia and subsequently entered the Polytechnic College of Pennsylvania, where he was graduated as Mining Engineer in 1865, at the age of nineteen. In 1865 and 1866, he was employed in railroad surveying. In January, 1867, he became draftsman and in 1869, assistant manager of the Glendon Iron Works, of which his father was manager until his death in 1875, when the son practically succeeded to that position, becoming formally in January, 1877, and remaining until February, 1887, the manager of the works and business agent of the Glendon Iron Company. In February, 1889, he became President of the Cranberry Iron and Coal Company, and held that position until November, 1897. He was a director of the Longdale Iron Company, Longdale, Va., from its organizationin 1870 until its dissolution in 1911. With the termination of this official responsibility, Mr. Firmstone retired from active business, although he continued to maintain an intelligent interest, and to play a helpful part, in the scientific progress of the iron industry, in which he had been a leader.

Jan 1, 1920

By M. D. Cooper

Production of both anthracite and bituminous coal in 1954 was about 16 pct below 1953. Estimates on Dec. 1, 1954, indicated 27 million tons of anthracite and 385 million tons of bituminous. Decline in production was due principally to lower demand by the steel industry and the railroads, although competition from other fuels also affected coal. The year was notable for vigorous effort by the coal industry to promote the use of its product. A Cabinet Committee on Energy Supplies and Resources Policy and an Interdepartmental Committee on the Soft Coal Industry were set up by the Administration in Washington. A Governors' Fuel Conference was also organized.

Jan 3, 1955

An overland belt conveyor system installed at Simco-Peabody's mine near Coshocton, Ohio, is presently carrying coal three miles at an estimated cost of 4.499 per ton-mile. Installed by Link-Belt Co. in late 1961, this system transports coal from open pit and underground mining operations to the Conesville Power Plant. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. In 1960 the power plant completed plans to enlarge by adding a third boiler. As a result, Simco-Peabody was required to provide means to produce and handle more coal. The haulage equipment, which consisted of one 90-ton, five 60-ton and one 50-ton off- highway trucks, was too small to handle the increasing daily coal demands. Annual tonnage was approaching a million tons and in a few years would be well over that figure.

Jan 4, 1963

By W. T. Jr. Thom

INTEREST naturally attaches to fissuring and subsidence of the earth's surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface.

Jan 1, 1927

By Andrew A. Blair

THE increased importance and value of chemical analysis in connection with metallurgical operations is largely, if not entirely, due to the increased accuracy of the analytical methods used for the quantitative determination of the foreign elements always associated with the metal operated upon. This applies especially in the working of iron and steel, and to the determination of the amounts of such elements as phosphorus, carbon, and silicon. The influence of greater or smaller amounts of these elements upon the physical properties of iron and steel will be better understood when the proper experiments shall have been made upon samples whose chemical composition is known with almost absolute certainty. From the present standpoint of analytical chemistry, it is easy to see that at least one reason for the failure of many attempts to solve this problem, is the inaccuracy of the analytical methods used. Even at the present time the frequent want of agreement (over and above the unavoidable error due to manipulation) between chemists working on the same sample, leads one to think that there is still at least a choice in the methods used. It is true that very frequently a faulty method in the hands of a skilful analyst may be made to give corroborative results

Jan 1, 1876