Search Documents

By Ramachandra Rao

THE occurrence of copper ores at Garimenapenta, 14 59 min 30 sec N Lat., 79 33 min 10 sec E Long., in Nellore district, Madras State, India, has been examined and investigated on numerous occasions during the past two centuries.' No tangible orebody was ever located as a result of all the ex- tensive trenching and shafting done in the area by various agencies. However, during 1933 Messrs. Piepmeyer & Co., a German firm engaged by one of the leaseholders of the area, carried out an electrical survey using inductive methods.' On the basis of certain strong indications found in their survey, they recommended that the prospect be proved by drilling or shafting. But for want of financial backing no further work was carried out. When the Madras government more recently proposed investigation, Dr. Krishnan, then Supt. Geologist of the Madras Circle, urged that before further costly ventures were carried out a test geo-

Jan 1, 1954

The new saw mill at Cache Bay of the Geo. Gordon & Co., Ltd., a subsidiary of International Nickel Co., of Canada, is equipped with the first fully electric saw carriage drives in Ontario. It has a capacity of 120,000 ft of lumber in an 8-hr shift. About half of the mill's production is high grade white pine lumber which is shipped to the general market. The other half, red pine is used in the mining operations of International Nickel in the Sudbury district, 55 miles west of Cache Bay. [ ] Inco with a potential need of 77 million board ft a year, gets only part of its supply from the new mill. The milling firm became an Inco subsidiary Jan. 1, 1948.

Jan 1, 1952

By Stanley C. Herold

TWENTY-FIVE years ago no distinction was made between water wells and oil wells except in the nature of the fluid produced. Water wells usually showed no decline in their rate of production; when oil wells showed decline something in the manner of handling them was considered wrong. Both water and oil were believed to be subject to the same physical laws in their underground movement toward the wells. Today a sharp distinction is made between them. Whereas water exists alone in the porous formations at depth, oil is usually accompanied by gas. This mixture does not behave as a liquid alone. It is a frothy, seething mass of foam which approaches and enters the wells. Different physical laws come into play. Twenty-five years ago attention was directed entirely to the well itself; today the well is accepted as a mere hole in the ground, a hole to be equipped properly for efficient service, yet without any value whatever unless it is backed up by a sufficiently prolific reservoir. Then, we were concerned with wells alone, 3000 ft. in depth; now commercial wells and their reservoirs are 10.000 ft. deep. Petroleum engineering concepts have necessarily therefore undergone a change in this last quarter century. What are they today?

Jan 1, 1937

By W. J. Schuster

*Original Pages Missing From Book HANNA COAL CO., Division of Pittsburgh Consolidation Coal Co., operates three large under- ground mines in eastern Ohio. The section of Pitts- burgh No. 8 coal seam in which these mines are located varies in thickness from 52 to 64 in. It is immediately overlain by a stratum of shaly material 12 to 15 in. thick locally known as draw slate, which is structurally very weak and which disintegrates rapidly upon exposure to atmosphere. Immediately above the draw slate as it is normally found is a band of extremely high ash material 6 to 12 in. thick known as roof coal or rooster coal, and above this is a stratum of conglomerate material varying from 4 to 10 ft in depth. Overlying the conglomerate is' a relatively thick stratum of limestone, the first stable material above the Pittsburgh coal seam in eastern Ohio. With the method of full-seam mining that has been adopted, draw slate is shot down, loaded with the coal, and removed in the preparation plants. The roof coal then becomes the permanent roof. The major problem in mining the No. 8 seam in eastern Ohio is control of the roof. Since the strata above the draw slate contains no material with a structure firm enough to provide self-support, the roof begins to sag in a relatively short time after the coal and draw slate have been removed. The problem thus becomes one of getting temporary safety posts under this roof as quickly as possible to prevent a break or separation from occurring either in the roof coal or in the conglomerate above it.

Jan 5, 1954

By E. A. Slover

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors

Jan 1, 1954

By W. D. Douglas, M. J. Hampshire, G. J. C. Young

This paper describes the replacement of a conventional filtration, clarification, and zinc precipitation plant by a carbon-in-pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers early laboratory studies to the design and erection of the full-scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies employed to solve them.

Jan 1, 1985

By W. A. Nordland

BISMUTH can be readily grown into single-crystal form using the so-called "quick freeze" growth method.' Some advantages of this method are that very large crystals can be grown in a relatively short time, and with comparatively simple apparatus. We have found the general quality of crystals grown by this method to be not as good as that of "pulled" crystals.' This communication describes a "quick-freeze"

Jan 1, 1968

By J. C. McHardy

During 1980-2000, the Florida phosphate industry will deplete its central Florida Polk County reserves. As a result, new mines will be built in the so-called southern Florida reserve areas. These mines will require new mining, beneficiation, and tailings disposal technologies since southern reserves have different characteristics than have been encountered in the central Florida deposits. Furthermore, government regulations will necessitate development of new tailings and clay disposal methods. This paper reviews these challenges for the Phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1984

By Don Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern.. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and-steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a 'general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim' their own metallic wastes.

Jan 1, 1928

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By B. S. Butler

It is suggested that at high temperatures both sulfur and iron combine with oxygen. Iron may precipitate at the high temperatures as the oxides of iron, and sulfur also in combination with oxygen as the low solubility sulfates of barium, strontium, calcium, and potassium (alunite). At lower temperature the precipitation results from change of sulfate sulfur to sulfide sulfur, and the iron precipitates as the sulfide.

Oct 1, 1956

By R. Hogg, F. F. Aplan, P. B. Bradley

The mineralogy of the solids contained in the black-water effluent from coal preparation plants has been investigated. Samples were obtained from 13 locations, representing major coal seam in the Appalachian, mid-continent, and western regions of the United States. On the average, the samples were found to contain 60% carbonaceous material with the balance as mineral matter. The mineral fractions from all of the samples from the eastern half of the United States were found to be remarkably similar, consisting of over 50% illitic clays; about 10-15% each of kaolinite, calcite, and quartz; and lesser amounts of chlorite and pyrite. The western samples were somewhat different, generally containing significant quantities of montmorillonite clay. Flotation may be wed to recover additional clean coal contained in the black-water discharge.

Jan 1, 1981

By J. B. Evans

Maintaining overall optimum profitability at a mine site necessitates constant reassessment of operating strategies. In essence, each strategy is a particular combination of envisaged capital expenditure, income flow and elapsed time. Selecting a strategy, based on profita¬bility potential requires each contemplated strategy being subjected to discounted cash flow analysis; even with a computer such analysis can be cumbersome. The chapter discusses a 'shortcut' technique which assigns profitability rankings to alternate strategies and iden¬tifies those aspects of a. strategy which impact heavily on profitabil¬ity. This technique can yield quick assessments of sufficient accuracy for many operating strategy decisions. taken on site at on-going mines.

Jan 1, 1978

GENTLEMEN Herewith are transmitted reports from the Treasurer and of the principal standing committees of the Institute. To these special reports members are referred for details as to the year's work. Despite the unfavorable business conditions obtaining throughout the year, the Institute was able to carry on its various activities without curtailment and without drawing on the surplus accumulated through previous years. In fact, small additions were made to the Life, Member¬ship and various other funds. It is highly desirable that such additions should continue to be made, especially to the Life Membership fund, for reasons reported last year. At present, money must be used from current receipts in order to enable the Institute to fulfill its obligations to those who on joining the organization commuted their dues by a single payment. In addition, with the passage of years the number increases of those who have paid dues forty years or more and who, by reason of age or dis¬ability, are unable longer to practise their profession. These men have supported the Institute through their active professional life and it would be a pity to lose them as members through resignation or for failure to keep up their dues. In accordance with the By-laws the Board has authority to advance such members, on application, to the Honor Roll of Senior Members and to relieve them from further payment of dues. It has been the policy of the Board to do this liberally, but to keep up this, as well as to meet other obligations, it is necessary for money to be provided. It has been estimated by the Treasurer that nearly $50,000 additional should be placed in the Life Membership fund as soon as possi¬ble to meet these obligations without using current income and to that end it is necessary, not only to avoid running behind currently but to earn, if possible, some surplus each year. The small amount transferred to the Life Membership fund from surplus this year was, as a matter of fact, made possible by certain members paying personally bills that were properly chargeable to the Treasury. Such generosity is common among those active in Institute work and probably no year would have closed with a surplus except for it.

Jan 1, 1923

By F. Cadena, Fred C. Bond, Walter L. Maxon

Grinding is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grinding installations. There have been some tests published, notably those of Lennox,' which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the comparisons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to be expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method. For example, let it be assumed that an ore to be tested consists of equal parts of difficult grinding mineral and easy grinding mineral. This is to be compared with an ore used as a standard, and consisting of minerals which are all of about the same grindability. If a comparison

Jan 1, 1935

JamEs F. Kemp, New York, N. Y.:—Mr. Hewett's paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally discovered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit eesentially asphaltite. The source and method of introduction afford a subject well worth serious reflection.

Jan 1, 1910

By S. Arthur Krom

Recent experiments indicate that the usual type of concen-trating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentratiug-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority of this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus marly have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concen-trating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is " bedded," that is, until a suffcient amount of metallic values has been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very limited carrying-capacity, considerable care must be taken not to overfeed a riffled table, in which case the table proceeds, in mill parlance, to rob itself. As soon as the space between the

Jan 1, 1912

By J. L. Hendrix, R. B. Dix

A study was made of the United States Bureau of Mines chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and mechanisms involved in the reactions between galena and sphalerite with chlorine. The influence of copper on the extraction rates was also studied. It has been shown that the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373 K with rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1981

By Benny Langston, Frank M. Jr. Stephens

IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. Considerable data has been accumulated on both operational1-4 and design5,6 of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process.

Jan 8, 1954

Andes Copper has an old camp and a new camp, both isolated until recent road improvements. The old camp is at Potrerillos and the new one at El Salvador, 25 road ,miles away. The company was incorporated in 1916 and the first mine, concentrator, leaching plant, smelter and town were built in the succeeding twelve years. The first blister copper was poured on January 24, 1927. Economic conditions determined the long development period but the end result was the design and construction of a mining complex that was all of a piece, unlike the piecemeal additions to El Teniente and Chuqui. The mining episode at Potrerillos came to an end in 1960 when the ore at La Mina became exhausted and the new mine, El Salvador was brought in. Both of these ore deposits come within four hpundred feet of the surface and had they been developed within the last five years might reasonably have been brought in as open pit mines. However, that is conjecture, and as it stands the operation at La Mina was so ideal for the mining method selected, blockcaving, it became a classic for the textbooks. On the other hand, El Salvador has turned out to be a blockcaving mine to test an engineer's skill. In mining the copper deposit at Indio Muerto mountain, there are ground conditions of every conceivable type. Tunneling in one section, the back can cave like sized pea gravel and only spiling can hold it; in another heading only the lifters are shot but often the rest of the round will sit down in one piece; elsewhere the bottom squeezes up and closes the drifts; and contrary to all other locations, there are sections where the block can be undercut without support. Today the scope of operations at Andes extends from mining to electrolytic copper. Ore is mined at El Salvador and the concentrator is also situated there. Concentrates pipelined 14 miles to Llanth, the water decanted, and then it is hauled by rail 40 miles and 5500 ft higher to the Potrerillos smelter and refinery. Potrerillos and El Salvador are respectively 90 and 70 miles from the port of

Jan 11, 1969