Search Documents

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.' Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By Cushwa, C. C.

AT the Park Utah Mine, labor costs of stoping A have been reduced from 30 to 40 per cent. by the use of double-drum hoists and scrapers. The application of scrapers varies with the methods of timbering. In stopes, which must be timbered with square-sets or stringer sets, one method is used; another is used in wide orebodies that can be held open until filling is introduced; and still another in narrow flat veins. Nearly all the oreshoots at the Park Utah lie at less than 50" from the horizontal, and most of the ore is difficult to handle through flat chutes. Proper care is probably the most important requisite for successful scraping, as serviceable equipment can be obtained from several manufacturers. One capable mechanic, therefore, was put in charge of the scraper hoists. He visits every stope daily, oiling hoists and tail1 blocks, inspects all equipment, splices cables and changes "set-ups" when necessary; his pay has been a good investment. The Park Utah now has in use ten double-drum Turbinair hoists, and one Sullivan double-drum a. c. hoist of the same capacity and outside design as the air hoists. The electric hoist is slower than the air hoists and does not pass large boulders easily; it is, however, a very effective machine. The air hoists are fast, powerful and

Jan 1, 1925

By William G. Pariseau

The extraction ratio approach to pillar design in flat seams is based on a mathematically exact analysis that is a reasonable physical approximation to room-and-pillar layouts in many instances. The essentials of the approach are reviewed and then mathematically approximate formulas for pillar design in inclined seams of arbitrary dip are proposed. Detailed numerical analysis of stress about a typical 5 entry, 4 pillar panel at dips of 0, 15, 30, 45, 60, 75 and 90 degrees at low and high extraction ratios show that the proposed inclined seam extraction ratio formulas for pillar normal and shear stresses, although conservative, have an accuracy quite adequate for engineering purposes. Appropriate pillar safety factors for compressive and shear failure and a safety criterion for overturning are specified.

Jan 1, 1982

By Charles F. King

The only investigations on record of the reactions occurring (luring the Bessemer blow are of charges containing a large percentage of manganese, with the exception of' two partial analyses by Snelus and Barker of the English method, where a low percentage of manganese was used. They do not give the analysis of the spiegel, [lor do they report any graphitic carbon after the first stage of the process. Both report only traces of manganese after the first stage until the addition of spiegel. The slags corresponding to the samples of metal were not analyzed.

Jan 1, 1881

By James Munroe

APPALLING as has been the loss of life in the last 51 months, there is one slight compensation : no longer will there be in the world a cripple, in the old meaning of the term. Men handicapped by wounds or disease, there will be, unfortunately, and in numbers beyond what the world has known since the wars of Napoleon; but neither they nor the industries from which they were called off to war will be "crippled" in the sense in which both would have been had mankind not learned the lesson of conservation and come to understand that the most important field for such conservation is not in the forests and' the mines but among men and women. From the beginning of the Great War, France, Great Britain, Belgium, and most of the other Allies have studied the problem of restoring the soldiers and sailors injured through war to physical and economic efficiency; and from their experiences, especially from that of Canada, the United States has learned much. Consequently, our task of preparing for the return of our disabled men has been easier and, in some ways, more comprehensive than theirs. Complex as are the details of the machinery which the United States has set in motion to take care of the men injured by wounds or disease, the plan itself is simple. Taught by European experience, the Surgeon-General of the Army and the Bureau of Medicine and Surgery of the Navy have provided, on both sides of the Atlantic, every known surgical and medical facility for restoring the injured or diseased man to a physical condition as nearly normal as possible. While in the hospital in France or England, on the transport coming to America, and in the hospital here, the disabled man is incited in every way to believe in his future efficiency, to want to be a normal worker, to desire to retake his place in that society of workers from which he went, temporarily, to do the greater work of preserving civilization. Furthermore, since purposeful occupation is now regarded as an essential form of, treatment with most men in the hospital, especially in the convalescing stage, many of these men will have been actually started on the road to earning before they are discharged from the army surgeon's care.

Jan 1, 1919

By Frederic Laist

IN the spring of 1931 an experiment was made at Anaconda with a small reverberatory furnace, with which was combined a roasting shaft. The arrangement is shown in the accompanying drawing (Fig. 1) and requires but little explanation. The general idea was to roast .flotation concentrates, mixed with the proper fluxing materials, by dropping them down a heated shaft, from which the calcines would enter the smelting zone of the reverberatory furnace through an opening in the roof. The hearth of the reverberatory was 3 ft. wide by 21 ft. long. The roasting shaft was 3 ft. square inside and had an effective height of about 20 ft. . The reverberatory furnace was arranged so that it could be charged either directly through the roof with regular hot calcines, in the usual manner, or by means of the shaft, at the top of which were a feed-ing arrangement by which cold flotation concentrates, suitably fluxed, could be fed continuously and a pipe through which cold air was blown in. Means were provided for distributing the feed over the cross-section of the roasting shaft. At first a mechanical arrangement was used but later it was found that a simple cone served the purpose equally well and gave less operating trouble. On account of the small size of the equipment, it was realized that absolute capacity and fuel consumption figures would mean but little. It was not to be expected that ratios comparable to those obtained in large furnaces could be gotten, and the only way in which any idea could be obtained as to the possibilities of the combination furnace was to run it in parallel with the reverberatory furnace charged in the usual manner and operating without the shaft. The results of such parallel runs are given in Table 1. The amount of oil burned in the reverberatory was purposely maintained at substantially the same rate during both runs in order that the benefits resulting from the shaft might be gaged.

Jan 1, 1933

By T. Leser, A. W. Jenike

The problems of caving and underground subsidence can be considered as the failure of a highly compacted rock and its subsequent flow in the form of broken rock. The problem is complex because the propagation of failure and flow have to be considered simultaneously; the yield strength of the virgin rock and the broken rock are different; and, while under certain conditions it is sufficient to consider the virgin rock as homogeneous, the density and the yield function of broken rock are both pressure and time dependent. A study of the failure and flow of solids with a pressure dependent yield function has been published recently by Jenike.' In this paper the density of the broken rock is assumed to be only time dependent and the consequences are examined in the case of one-dimensional vertical subsidence into an initial cavity. The following describes an attempt to develop a tool which, in combination with other tools, may lead to mathematical solutions of real problems of caving and subsidence. STATEMENT OF THE PROBLEM An underground cavity of horizontal cross section 4 = 1 and height 6 is assumed to exist at some depth below the surface. At the time t = 0 rock above the cavity fails and completely fills out the cavity with expanded broken material. With passing time the broken rock consolidates and subsidence proceeds continuously upuard in a vertical shaft. The phenomenon is one-dimensional (see Fig. 1). The problem consists of finding the displacement and the velocity with which the frlmt of the subsidence (wave front) moves upward as a function of the time and of the rock properties. DIFFERENTIAL EQUATIONS CONTROLLING THE PHENOMENON With the assumptions that the broken rock is a continuum and that the subsidence occurs continuously, we can apply the one-dimensional differential equation of contitiuity (conservation of mass) and the equation of preservation of momentum The latter equation is replaced by an assumed relation based on experience, which takes care of the

Jan 1, 1962

By W. Spencer Hutchinson

THE outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations. are shown for the years 1900, 1930 and 1950 in Table 1.

Jan 1, 1933

By Nicholas T. Camicia

Coal is one of our oldest known commodities. Historic evidence indicates that this fossil-formed fuel was used in China and in Wales some 3000 to 4000 pears ago. Coal was discovered in North America in 1679 by French explorers in northern Illinois, and in 1700 a colony of Huguenots came across bituminous coal in Virginia. One might think by this long history of a single commodity that the string was about played out. Quite the contrary, coal is in greater demand than ever before and coal mining today is a modern industry. It is in an unprecedented growth period as the nation-and the world-demands more and more energy coincident with dwindling reserves of other fossil fuels. By the year 2000 the demand for coal is expected to at least double the current level of some 600 million tons annually despite the advent of nuclear power. To meet this challenge, the coal industry is vitally in need of an increasing supply of technically trained and progressive manpower. And, coupled with a serious shortage of engineers and technicians, it represents a rich vein of occupation opportunities-all the way up to top career levels. Today, coal mining is a complex, highly specialized industry concerned with more than just getting coal from the earth and putting it into the furnaces of the consumer. The industry is concerned with the environment, with maintaining a viable ecology. Recognizing the ramifications of global economics, the industry is very much aware of its important position in contributing to a constantly rising standard of living throughout the world. The key to rewarding employment in the coal industry is skill-skill that has been developed by education, training, and experience. None of these alone is enough; all three are necessary today to produce the skill needed to meet the employment requirements of the coal industry. Routine manual labor will no longer do the job in coal mining. In the United States coal mining has been mechanized to a degree unsurpassed anywhere else in the world, and the coal worker must be thoroughly

Jan 1, 1973

By W. Mont Ferry

It is impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affectcd. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direet-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followrd by other smelting and reduction companirs and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silvrr ores was the principal prob1t.m to be solvcd. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc corlcentrates. This period includes the world war, when abnormal priccs stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. Production and Value of Zinc Concentrates The production of zinc concentrates during 1924 was approximately 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By A. S. Nowick, A. E. Roswell

Anelastic measurements of atomic mobility in an Ag-Zn substitutional solid solution, make possible a study of the rate of decay of lattice defects frozen into the alloy by quenching. A WIDE variety of experimental evidence has accumulated recently in support of the belief that atomic mobility or diffusion in face-centered cubic lattices occurs principally through the movement of lattice defects, as contrasted to a mechanism by which two or more atoms directly exchange lattice positions. The most direct evidence, summarized in a recent review,' includes the Kirkendall-effect measurements and anelastic measurements on quenched alloys. Theoretical calculations' have focused attention on the lattice vacancy as the defect probably responsible for diffusion in the common metals. Later calculations3 have also shown the possible importance of combined pairs of vacancies in producing diffusion. The only defect that has been considered seriously, in addition to the vacancy and combination of vacancies, is the "interstitialcy" (an atom which has left its normal lattice position and entered an interstitial position) ; the calculated energy of formation of an interstitialcy in a close-packed lattice is too large to permit a reasonable probability for the occurrence of this defect In view of these calculations it may be tentatively concluded that the defects producing atomic movements are single or multiple vacancies. Anelastic measurements of atomic mobility in substitutional solid solutions provide a valuable method for the study of lattice defects. By means of this method it was first demonstrated' that defects may be frozen into a lattice by rapid quenching from high temperatures. (It was subsequently shown6 that resistivity measurements may also be capable of detecting the presence of frozen-in defects.) A summary of the principles involved in these anelastic measurements will now be presented. The anelastic method is based on a relaxation phenomenon in substitutional solid solutions, first discovered by Zenera in a brass and subseauentlv investigated extensively in a series of Ag-zn solid solutions.' This relaxation effect may be observed in the usual way either dynamically, as a peak in

Jan 1, 1954

By J. E. Lawver, R. R. Beebe, J. L. Wright

This paper describes a separation coefficient Ks useful as a "measure of goodness" to be used in factorial and response surface methodology. The use and limitations of the separation coefficient is discussed, and a computer program for calculating the coefficient is presented (in Fortran). The application of the coefficient is illustrated in terms of electro-dynamic separation of Mesabi semitaconites. Present Mesabi wash ores and gravity concentrates with an iron to silica ratio of only 5 or 6 to 1 are no longer readily salable, for the steel industry now demands concentrates with an iron to silica ratio of at least 10 to 1 and a structure comparable to pellets. THE ELECTRODYNAMIC-FLOTATION PROCESS Wash ores and gravity concentrates consist largely of hematite, goethite, and quartz. Several methods of beneficiation are being tested at the University of Minnesota Mines Experiment Station with a view to improving the salability of these materials. A process that looks particularly promising from an economic view is the combination electrodynamic-flotation process shown in Fig. 1. This process is designed to upgrade gravity concentrates to a 5% silica content and to provide fines — from the flotation circuit —to permit agglomeration. Although electrodynamic concentration of specularite is an established and well-understood process, the electrodynamic concentration of Mesabi goethite-hematite gravity concentrates presents interesting and enigmatic problems. The gravity concentrates are by no means assemblages of clean, free mineral particles. Instead, the concentrates to be retreated consist of a great variety of middlings. More or less complete liberation would require grinding to minus 325 mesh, at which size only flotation could be expected to function, and even then grades and especially recoveries would not be satisfactory. A close examination of the gravity concentrates shows that grinding to 100% minus 48 mesh will produce a product which is approximately 70 weight % plus 325 mesh (see Fig. 1). The remaining 30 weight % can be deslimed and floated by conventional methods, but the resulting iron concentrate is

Jan 1, 1964

By M. M. Fidlar, Ralph E. Esarey

A marked decrease in drilling during 1937 in Indiana seemed to have no undesirable effect upon the oil and gas industry. Instead, production figures for oil showed a small increase over those for the preceding year, although not so much gas was marketed as in 1936. Drilling activity was centered in proven areas, and the proportion of dry holes to the number of wells drilled decreased somewhat. During 1937, including old wells drilled to deeper horizons, 134 wells were completed in Indiana, of which 39 were oil wells, 39 gas wells, and 56 dry holes. Nearly 75 per cent of the holes were drilled in proven areas. Of the 36 wells drilled in wildcat areas, only four found commercial production. Wildcat wells were especially numerous in Vigo, Pike, Perry and Spencer Counties. Exploratory drilling activity in Vigo County resulted in part from the drilling of the discovery well in the new Prairie Creek field. In Pike County, wildcat wells were drilled in the search for new supplies of gas to meet the demand in the southwestern portion of Indiana. Drilling in both proven and wildcat areas in Perry and Spencer Counties continued to be heavy, because of the presence of shallow Missis-sippian sands and the resulting low cost of drilling and equipping. At the end of the year, 42 of the wells started in 1937 were not completed. Only a few locations were drilled in the old Trenton field, but the wells, many of them 40 years old, continued to furnish a small supply of gas for domestic consumption. Oil production in the Jay County portion of the Trenton area was nearly twice that of 1936, owing in part to a vacuum system installed on several leases. The Harrison County (Laconia) gas field is being developed northward to offset water encroaching from the south. This water in the black shale threatens to put an end to the steady production that this field has furnished for many years. During 1937, the Oaktown gas field again furnished more gas than any other field, but production in that area showed a marked decrease over the marketed gas for 1936. During the early months of the year, seven wells were completed in the Oaktown field to bring the total number of producing wells to over 40. At present, all the operators in the area are

Jan 1, 1938

By Howard Eavenson

ONE who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regula-tion of some sort is needed if any stabilization is to be achieved and if the Wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920-to the end of 1934-the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are- considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing., of the high wage scale of that agreement, which soon proved to be an uneco-nomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By D. M. Buck

greatly restricted and every effort is being made to do away with it where possible, and to substitute a lead-base babbitt or a babbitt with 50 per cent,. tin. The amount of solder having the composition 50 lead, 50 tin, used by the Pennsylvania Lines East, during 1917, was approximately 100,000 lb., but there is reason to believe that a large portion of this can be replaced by a 60-lead, 40-tin solder with satisfactory results, and instructions have been issued to this effect. Inregard to the quantity of new tin used, it is not possible to give the amount, except approximately and from calculations based on the 1917 consumption of bearing metals by the Pennsylvania Lines East only, it is estimated that about 770,000 Ib. of new tin were required in a total of about 21,380,000 lb. of all kinds of bearing metals turned out by the foundry or purchased in the market. No change has been made in the specifications for bearing metals for some years, as the metals used have been satisfactory. A large proportion of the bearing metals are made up from old material re-melted and brought to standard composition by some addition of new metal, and every effort is being made to utilize old material to the best advantage and reduce the amount of new metal of all kinds purchased. For a number of years no tin has been used in the lining metal of either passenger or freight car journal-bearings, except such small amounts as come in from re-melting old linings. No change has been made in phosphor bronze used for rod bushings, as we should expect some trouble from bushings pounding out of shape if a phosphor bronze were used which contained less tin or more lead than the present specifications call for. In this, as well as in the case of all other bearing metals, we expect to use our utmost endeavors to economize and to substitute for tin wherever possible. The Tin-plate Industry D. M. Buck,* Pittsburg, Pa.—During the first 5 months of 1918, approximately 11,000,000 Ib. per month of pig tin were consumed in the United States. Solder, bearing metals, bronzes, etc, used about 5,500,000 lb.; collapsible tubes a little more than 250,000 lb.; tin-foil about 500,000 lb.; and the tin- and terne-plate industry somewhat less than 5,000,000 Ib. In an effort to reduce this consumption and thus conserve our tin supplies, several methods of procedure suggest themselves: 1. Salvage. The most careful and systematic collection and re-use of tin and tin-bearing materials is economically important, in that we thus

Jan 1, 1919

By Clinton L. Miller

MINING operations have been carried on in the immediate area of the Elizabeth mine during periods of high copper prices since 1793, when copperas and vermillion were first won from the outcrop. Present operations started in 1942 as a war baby. Since then production has totaled 1.7 million tons of 1.8 pct Cu ore. Elizabeth mining operations are on a pyrrhotite- chalcopyrite orebody contained in a gently plunging amphibolite syncline. The oreshoot varies in width from 10 to 40 ft, and in the area under consideration is about 150 ft in vertical extent, and more than 1000 ft long. Surface pits or cuts have been worked in three areas along the outcrop, with one pit just completed and a second in full production. Present production is 24,000 tons per month, of which 6000 to 7000 tons is trucked from the open pit.

Jan 11, 1954

By C. G. Rhodes

A technique for producing etch pits in uranium monocarbide has been developed. The pits, which are assumed to be associated with dislocations, appear individually and as arrays delineating sub-boundaries, as seen in Fig. 1. The samples used were single crystals prepared by the technique described by Nadler.* Uranium

Jan 1, 1963

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers' logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller's descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

Jan 1, 1925

Jan 1, 1951