Search Documents

By G. D. Oxx, L. F. Coffin

The concept of using a phase that is liquid at service temperatures as a component of coatings for refractory metals has been described. The liquid, an alloy of gold and silicon, is retained on a molybdemum surface by a capillary system made of molybdenum disilicide. The coating has the advantage of good thermal shock and has a self-henling chracteristic. In order for highly stressed structures to exceed a service temperature of 2000°F, it has become apparent that a development that does not depend on the traditional iron, cobalt, or nickel-base alloy is needed. Alloys of the refractory metals, i.e., molybdenum, tungsten, tantalum. niobium (colum-bium), and rhenium are potentially useful at extremely high temperatures that more conventional alloys would never be expected to achieve. A new alloy of molybdenum has become available that has a 100-hr rupture strength of 35,000 psi at 2200°F.1 As a result of this work, it may be assumed that a material with adequate mechanical properties at 2200?F is now available. Unfortunately, this alloy and all other known alloys of the refractory metals suffer from not being; serviceable in an oxidizing atmosphere for a very long time. In order to permit general use of refractory metals at high temperatures, it is necessary to prevent destructive oxidation by appropriate alloying or by protective coatings. The liquid phase coating reported here is representative of a concept for the protection of metals that permits higher service temperatures and introduces a new group of materials for selection as coatings. Coating Requirements—Service conditions that represent potential applications for refractory metals vary considerably: however, it is possible to consider two conditions that are usually present. The refractory metal1 component must be heated to the service temperature at least once and usually frequently. When a solid coating is used, usually the coating and basis metal do not have the same coefficient of expansion. This difference causes thermal stress in the coating that is aggravated by rapid heating and cooling and eventually causes coating failure. The second consideration is the probability that there will be damage to the coating by some environmental condition. In jet engines, for example, it is expected that large particles, stones, metal parts, and so forth, will strike a bucket at high speed and cut a hole in the coating. In addition to the above considerations, the coating must also have other fundamental properties. Obviously, it must be oxidation resistant. In addi- tion, it must prevent permeation of oxygen and subsequent oxidation of the basis metal at the interface. Also, diffusion of the basis metal to the outside surface and subsequent oxidation there must be prevented. Finally, the coating must not react with the basis metal to form a weak bond at the interface. It should be noted that the coating need not support a load: it must only remain intact. Liquid Phase Coating Design Factors—In the use of a liquid as a principal coating constituent, it would be expected that the two service conditions mentioned above would be satisfied. A liquid would flow under the influence of the thermal strain developed by coating-basis metal expansion mismatch such that failure from this source would not be expected to occur. It is also probable that the ability of a liquid to flow would provide a self-healing effect. Thus, damage caused by particles in the atmosphere would be repaired. A third advantage is evident in that vapor pressure rather than melting point limits the service temperature. This latter advantage permits use of low melting but oxidation resistant metals such as gold or copper that would be quite useless if the solid state was required. A low viscosity liquid alone. however, is a totally unsuitable coating because it will simply flow off a component, particularly under the influence of a high acceleration field. A method of preventing liquid loss must be devised. In this case, it is desired that the liquid have a low viscosity so that it may easily flow into flaws; thus, raising the viscosity is not a satisfactory solution. One other inherent difficulty is caused by the high mobility of atoms in the liquid state as compared to the solid state. Because of this mobility, it would be expected that gases would diffuse more rapidly through a liquid. It is also probable that the solubility of oxygen in the liquid would be comparatively high. These factors would tend toward rapid permeation of oxygen and oxidation of the substrate. It is most reasonable that this problem could be solved by incorporating a solid phase, which is impermeable to gases, as a component of the coating. To overcome the tendency of a liquid to flow easily, it is possible to use surface tension to advantage. If the surface were made up of a large number of capillary tubes of sufficiently small diameter, then surface tension would hold the liquid even against the acceleration of a centrifugal field.

Jan 1, 1961

By Michael A. Arkoosh, E. A. Peretti

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970

New equipment for seabed sampling, presently at the prototype stage, operates on the principle of diamond core drilling with wire line core barrels and is designed to drill cores from the seabed at depths down to 200 m with a continuous recovery of cores from an attendant vessel. The machine operates on the seabed by remote control from a console on the vessel. Neither installation nor operation requires the use of divers. Principal Applications Principal areas of application for the drill which is dubbed Maricor include investigation drilling in the continental shelf, mapping geological conditions before large drilling platforms are installed and exploring proposed undersea tunnel routes.

Jan 11, 1973

By E. J. Wasp, T. C. Aude, F. B. Raymer

Abstract-The following paper deals with technical aspects of terminal facilities for western coal pipelines. The information is taken from the Ohio and Black Mesa pipelines and the proposed one in Wyoming. This paper first discusses the feed terminal, the product that it must produce, and the reasons for coal cleaning. Then, in the delivery terminal section, the various methods of dewatering the coal and some recent innovative ideas on bunkering the dewatered product and storing the dewatered coal in large outdoor piles are discussed.

Jan 2, 1978

By Salim Akhtar

The operation of a mineral processing plant with a complex flowsheet is represented by a mathematical operator. Such a representation permits a quantitative evaluation and monitoring of the separation processes in different sections of a processing plant, and gives an overall separation efficiency of the plant.

Jan 1, 1975

By R. H. Foley

It is difficult to consider any seam as unsuitable for longwall mining operation for something like 95% of British coal is produced by this system. The following is a brief report on how they do it-their techniques and equipment. Depth of working in British mines varies from about 150 ft to more than 3000 ft, with the average being about 1300 ft. Average seam thickness is approximately 40 in., but working seams vary from 16 in. to as much as 14 ft.

Jan 8, 1965

By G. D. Van, Arsdale

IT IS particularly appropriate that a paper on this subject should be presented in Spanish, before a Spanish speaking audience, and in a South American country, first because of the facts that these countries today have not only the largest copper leaching plant in existence but also present great opportunities for future extension of hydrometallurgy; and second, because of the fact that the first copper made by any wet method was doubtless produced before existing records at the Rio Tinto deposits in present day Spain.

Jan 1, 1925

By Joseph Bernhardt

Use of concrete underground at No. 4 mine, Cornwall, Pa., has become increasingly important. Starting with small amounts at finger openings, occasional raises, piers, its use has expanded to entire slushing drifts and haulages. Besides eliminating costly timber repairs, concreting costs of slushing drifts have proved cheaper than timbering. Higher haulage-concreting costs are offset by no maintenance charges during the life of the haulage.

Jan 3, 1950

By P. G. Mason

The upswing in the price of gold in 1979 prompted renewed interest in the Mercur gold property by Getty Oil Company, owner and operator, and Gold Standard Inc. of Salt Lake City, Utah, currently retaining a 15% net profits interest. Extensive geological exploration work resumed to delineate the ore reserves, and metallurgical test work was initiated under the direction of A.H. Ross & Associates. This led to the development of an aqueous pressure oxidation process suitable for treatment of the refractory ores. Subsequent geostatistical studies revealed that the distribution of high refractory ore was less than previously estimated, and thus a higher return on investment could be realized if a direct carbon-in-leach process were used despite a sacrifice in overall recovery. This paper reviews the geological and metallurgical studies that led to this final process selection.

Jan 1, 1984

By Fred C. Bond

SIZE of grinding media is one of the principal factors affecting efficiency and capacity of tumbling-type grinding mills. It is best determined for any particular installation by lengthy plant tests with carefully kept records. However, a method of calculating the proper sizes, based on correct theoretical principles and tested by experience, can be very helpful, both for new installations and for guiding existing operations. As a general principle, the proper size of the make-up grinding balls added to an operating mill is the size that will just break the largest feed particles. If the balls are too large the number of breaking contacts will be reduced and grinding capacity will suffer. Moreover, the amount of extreme fines produced by each contact will be increased, and size distribution of the ground product may be adversely affected.

Jan 5, 1958

By Claudio Gutierrez

It has been claimed (Eadington and Rosser, 1969) that when freshly precipitated lead sulfide is in contact with oxygen-containing water, there is an "induction period" of at least a few hours during which no detectable oxidation of the lead sulfide takes place This effect would be of the utmost importance for the adsorption of xanthate on galena in flotation mills. It was tried here to reproduce the results obtained in (Eadington and Rosser, 1969), but no "induction period" was found. Besides, reasons are given to prove that the oxidation mechanism proposed by Eadington and Prosser (1969) is not realistic.

Jan 1, 1982

By B. Barlin, G. A. L. Smith, I. J. I. Delaney

A method was developed to quantify the three mineral species, sphalerite, galena, and pyrite in seven concentrator products. Intermineral effects were studied and a statistical analysis was undertaken to assess the accuracy and reproducibility of the method. The method is both rapid and suitable for plant control purposes. Furthermore, it requires only semiskilled laboratory personnel to carry out all the analyses.

Jan 1, 1976

By Minoru Yamada, Eikichi Mohri

INTRODUCTION Most of the copper concentrates treated by the flash smelting furnace at Kosaka smelter come from "black ore" that is produced in the local mines nearby. The copper concentrates contain various impurities such as lead and zinc as shown below. [ ] These impurities are mainly concentrated into the flue dusts in the copper smelting system. The dust production rates of flash smelting furnace and converter at Kosaka smelter are, therefore, fairly high compared with other copper smelters. However, by recovering these valuable metals in the dusts systematically, profit-increase of the by-products must be expected. This also leads to the solution of environmental pollution problems and enables us to establish the technical completion of complex sulfide ore treatment by flash smelting process. HISTORY OF DUST TWATMENT AT KOSAKA SMELTER 1) December in 1967 to January in' 1969 Since the flash smelting furnace started its operation in December 1967, all the dusts from the furnace had been recycled. Only conver-

Jan 1, 1976

By C. M. Loeb, A. M. Gaudin, J. H. Brown

R. E. Carter (General Research Laboratory, Schenec-tady, N. Y.)—Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crys-tallographic directions, and in materials containing quartz because of the a-p' transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 1, 1960

By Branko Ladanyi

In reviewing the current issues in rock mechanics, the author puts an' emphasis on problems related with the needs of extrapolation in scale and time, and of establishing proper conceptual models, especially in connection with the most recent large-scale and long-term projects such as underground disposal of nuclear waste. In such projects, where valid case histories will not be available for many years to come, the observational method can only be successful if combined with a proper framework approach, such as general rock mass classification systems and behavioral models.

Jan 1, 1982

By Felix G. Berra, David H. Orr

The first large scale application of radio remote control equipment to standard gage railroad trains has been achieved at the Morenci mine of Phelps Dodge Corp. at Morenci, Ariz. Twenty or more ore and waste haulage trains are remote control operated at any one time, each with a one-man crew. Reduction of train crews from two men to one man has materially lowered the total cost of train operation. Elimination of brakemen has also resulted in an improvement in train efficiency brought about by a shortening of train haulage cycle times.

Jan 4, 1965

By Niles E. Grosvenor

Complex underground mining problems are increasing as mining depths increase. Many of these problems have been solved mainly by unsystematized trial-and-error methods based on individual experiences. This system of solving mining problems has resulted in over-cautiousness whereby a large quantity of our mineral resources are left in the ground, or not enough caution with a resultant failure of the underground opening. From studies made of physical properties of rocks, large volumes of data have been collected as a source of finding correlation among the different physical tests or among certain rock types. Most of these studies have not produced satisfactory results because the investigator usually arrives at the conclusion that the results are too scattered to be reliable. The reasons usually given as the cause of this scatter are that rocks are nonhomogenous and non-isotropic. Similar types of poor correlation that were being obtained from compression tests in the Colorado School of Mines Mining Research Laboratory led to an investigation of a good method of making a simple unidirectional compressive strength test.

Jan 1, 1963

By W. A. Backofen

THE preferred orientations, or textures, resulting from many of the various methods for testing and forming metals have been the subject of numerous investigations.1,2* Despite this large amount of work, however, only a few limited studies have been made of the texture that is developed by torsional deformation. Ono3 found that in severely twisted wires of copper and aluminum a [Ill] direction lies parallel and a [1101 direction perpendicular to the longitudinal axis of the wire. Sachs and Schiebold4 have reported that a double-fiber texture exists in a twisted aluminum wire with both the [Ill] and [loo] directions parallel to the axis of the wire. Twisted iron wires have also been examined by Ono.8 Both the [1101 and [1121 directions were reported as parallel to the axis of the wire. Goss5 concluded from a study of twisted rods of a low-carbon steel that the preferred orientation existing at fracture is quite complex, but that many grains have a [1101 direction parallel to the axis of the wire. In addition to the earlier experimental work, some suggestions have been made about the possible nature of the torsion texture. These suggestions are based on the results of many experiments which indicate that the cold-working texture of a particular metal is largely determined by the geometrical change in shape that the metal undergoes during plastic deformation.1,6 Hibbard and Yen7 have considered the problem of deformation textures and have presented an analysis which is able to explain why equivalent changes in shape should yield similar textures. Therefore, a knowledge of the principal strains associated with torsional deformation would seem helpful in the interpretation of the torsion texture. The necessary analysis has been made of the state of strain in an element of metal lying in the surface of a cylindrical rod or tube that has been subjected to pure torsion.8,9 This analysis shows that the directions of the principal normal strains rotate continuously within a torsion specimen while it is being twisted. After the first infinitesimal amount of twisting, these directions make angles of 45" with the longitudinal axis of the bar. They rotate from this position as twisting proceeds, and after an infinite amount of twisting, the direction of the principal tensile strain is perpendicular, and the direction

Jan 1, 1951

By Carlos Kovacs-Figueroa

Complying with air pollution regulations created the need to dispose of increased sulfuric acid production by the Morenci smelter. As a result, a two-module leaching plant was constructed to leach Morenci flotation tailings. The leaching plant was equipped to perform the following operations: leach feed pumping, agitated leaching, two-stage countercurrent decantation, neutralization of leached tailings, and copper precipitation. Ancillary facilities were provided for neutralizer and flocculant preparation as well as precipitant handling and recovery of precipitates. Plant control is automatic from a central control panel supervised on a shift schedule by one operator and two helpers. Construction of the first module was initiated in April 1973 and leaching of tailings commenced in November 1974. Construction of the second module began in January 1975 and was completed in November 1975.

Jan 1, 1977

By Charles J. Speake, Dennis R. Haley, Thomas E. Finch

The tremendous interest in development of surface- mineable coal throughout the western US will bring with it a requirement for many manhours spent in mine planning and equipment selection. One problem in particular that engineers face during the planning stage is that of selecting a dragline with the proper reach capability. Reach, expressed in terms of operating radius and effective spoil radius, can be a major problem when mining deeper than originally planned, and aside from production requirements, the ability of a particular dragline to spoil across a strip is essential. Determination of dragline reach needed for a multiple-seam western coal operation can be simplified by use of an equation derived below that eliminates the need for tedious and repetitive calculations.

Jan 5, 1977