Search Documents

By James R. Aggson, John C. Curran

In a cooperative research effort, the US Bureau of Mines Denver Mining Research Center and the Pittston Co. investigated floor heave ground control problems that have plagued underground coal mining of the Beckley coalbed in southern West Virginia. Floor heave is accompanied by a redistribution of stresses and loads that are associated with underground openings, causing roof and pillar problems. The floor and roof analysis techniques that were used in the USBM/Pittston investigation may have a wide range of applicability in the mining industry. Recommended orientations and geometries for mining operations are directed at floor problems, but may also enhance roof stability.

Jan 1, 1980

By H. A. Fisch, A. J. Opinsky, J. L. Bartos

Fort?-six- two-grain bounduries were studied in doped tungsten 1amp wire that had been heated to 3450°K very vapidly. Back-reflection Laue photograms were taken of the grain boundary partners and solved, using a computer. The resulting distribution of large-grain orientations was analyzed. Rotational axes were calculatedfor each grain boundary pair. The axes of least rotation show an anisotropy of rolalional angle. WhILE the orientations of large grains in straight doped tungsten wire have been studied extensively, little has been done to characterize the boundary that separates them. Rosi.1 upon seeing the jagged interlocking boundary in doped tungsten wire. inferred that the grains should have a preferred orientation, and proved it. He interprets his data as indicative of a single ideal orientation—(531)— being parallel to the wire axis. Rieck2, 3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Siegle argue that the data suggest that (211)—a plane-is parallel to the wire axis instead. This (211 ) contains the (531). and hence would appear to be a more general case.5 Ahlborn and wasserman6 report that their orientation data stretch from (110) through (531) to (311). This path is the locus of {211 Recently. Opinsky has suggested that the data can be interpreted as a series of ideal orientations that can be related by coincidence relationships to the (110) fiber texture. All these investigators have determined the orientations of the large grains by the back-reflection Laue technique, and they have all obtained similar results. Only Rieck5 as methodically looked at the large grains along a wire. He was apparently not concerned with the relationships of the large grains across their common boundary, but only with their individual orientations. This research was undertaken to fill this gap in the under standing of the mechanical properties of tungsten wire. Only the crystallographic aspects of the problem will be reported here. In addition, the large number of large-grain orientations, which was accumulated in this study. will also be analyzed. EXPERIMENTAL MATERIAL AND TECHNIQUES All of the data were obtained from four pieces of the same 7-mil-diam General Electric tungsten lamp wire. Twelve-inch lengths of the cleaned wire were heated in vacuum by the flick of a switch to 90 pct of the amperes necessary for fusion (a temperature of approximately 3450°K) and held for 1 min. On the basis of other data. it is estimated that the rise time is of the order of 0.5 sec. The four pieces of wire could have come from anywhere within about 18 ft of wire. Consecutive segments of each piece of wire were mounted in bakelite and polished metallographically The polishing procedure followed that described by woods. "nly boundaries between two grains that each occupied the entire cross section of the wire were photographed and X-rayed. The metallographic sample was mounted accurately with respect to the X-ray unit. Steps were taken to read the films as accurately as possible with the conventional Greninger net. The data were then entered into computer programs that solve the Laue film by precisely the same techniques that are used in the solution of the film by means of the stereographic projection. The use of the computer has probably shifted the main source of error from the stereographic plot to the reading of the film. On the basis of several experiments, it is thought that the error associated with the entire process, from mounting the sample through the computer solution, is of the order of about one-half degree. The output of the computer is the direction cosines of the fiducial direction (the wire axis) and the locations of the three cube axes. The former data were used to calculate the differences in orientation between the two grain boundary partners, and the latter were used in the calculation of the rotational axes that could bring the two grains

Jan 1, 1970

By Walter W. Fisher, Samuel Rudy

Secondary treated sewage effluent was substituted for normal process water in laboratory tests simulating froth flotation recovery of copper and molybdenum sulfides. Sewage effluent caused significant detrimental response in the flotation process. First, a voluminous, uncontrollable froth was generated, even in the absence of a frothing agent, that has little mineral carrying ability. Second, sewage effluent caused a small loss in copper recovery and a large loss in molybdenum recovery. The detrimental effects of sewage effluent on flotation were partially overcome by tertiary treatment of the effluent by activated carbon adsorption and anion exchange. The frothing problem was significantly reduced after treating the sewage effluent by foam fractionation. Dilution of the effluent with normal process water resulted in a significant improvement in metal recovery. In addition, the large loss in molybdenum recovery was overcome by using a secondary collector in a combination reagent schedule. However, the secondary collector caused an appreciable loss in copper recovery.

Jan 1, 1979

By W. T. Jr. Thom

INTEREST naturally attaches to fissuring and subsidence of the earth's surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface.

Jan 1, 1927

By Robert I. Jaffee, Walter L. Finlay

IN the broad survey of the nonferrous' metallic elements contained in this book, the reader may well be impressed by the wide range of property combinations offered by the many metals and alloys the metallurgist has prepared since before Kubla Khan. The diversity is great and the overlap is considerable. It is particularly surprising, then, to find the latest structural metal new- comer designated by such extravagant terms as "Cinderella Metal," "Wonder Metal," "Miracle Metal," "The Metal of Tomorrow," "Dream Metal or Nightmare?" and "The Middleweight Champion of the Structural Metals." Of these and others, the most appropriate designation for the metal involved, titanium, appears to be that of The Middleweight Champion. Its intermediate density of 4.5 and elastic modulus of 16 million is a unique combination between the lower density and modulus of magnesium and aluminum and the higher density and modulus of copper, nickel, and iron. It is light, strong, ductile, and corrosion resistant. A chemical neighbor in group IV of the Periodic Table, zirconium, is similar to titanium in many respects but is appreciably denser, 6.5 instead of 4.5, less stiff and relatively much less abundant. On the other hand, the resistance of zirconium to acids and alkalies is better than that of titanium. Also, compensating for its higher density, lower stiffness, and somewhat lower strength level compared with titanium, zirconium has much better permeability to slow neutrons and is much more suitable as a material of construction for nuclear reactors.

Jan 1, 1953

By G. H. Matheson, J. M. W. Mackenzie

The coal concentrates studied contained clay slimes which would not flocculate on the addition of a polymer flocculent alone. The mechanism of the flocculation process is interpreted on the basis of the flocculation of lyophobic colloids. The filtration rate characteristics are shown to deviate slightly from certain basic filtration equations. Cake moisture was shown to decrease with cake drying time and vacuum, and increase with cake thickness. Filtration is a commonly accepted method of dewa-tering the fine coal concentrates produced in coal cleaning operations. Dewatering of these concentrates, using drum or disc vacuum filters, usually presents few technical difficulties and will result in the production of a filter cake containing some 20 to 25 pct moisture. In many coal cleaning operations it is common practice to add flocculants to the coal concentrates prior to filtration to increase the filtration rate. The mechanism whereby flocculation increases filtration rate has been summarized by Gaudin,4 while Geer, et a15 have compared the effectiveness of starch and synthetic flocculants as filter aids for a variety of coal concentrates. Coal concentrates, containing appreciable quantities of expanding lattice clays of the montmorillonite-illite group, sometimes prove impossible to filter without flocculation of the pulp prior to filtration. The fine coal concentrates produced at the Newcastle washery of The Broken Hill Proprietary Co. Ltd. fall into this group. Coals mined in this district contain appreciable quantities of expanding lattice clays which break down in the washery circuit waters and, by processes of mechanical inclusion, contaminate the coal concentrate thickener feed. Despite the classifying action of this thickener, the underflow which is pumped to the filters contains sufficient clay slimes to render filtration of the unflocculated pulp impossible. Filtration leaf and plant tests were carried out to develop effective and economic flocculant combinations and to determine the filtration characteristics of the flocculated coal concentrates. The determination, by leaf testing, of the filtration characteristics, and the analysis of these characteristics in the light of the equations of Brown2 resulted in the successful trial operation of the filters in the Newcastle washq. Although the filtration characteristics are not entirely in agreement with the theoretical treatment of Brown, the equations developed made it possible to predict, from leaf tests, the effect in the plant filters of pulp density, form vacuum, and form time on filtration rate and filtrate volume. EXPERIMENTAL PROCEDURES The sample used for leaf testing was the coal concentrate thickener underflow, which in plant operations would form the feed to the two 12-disk Dorr-Oliver filters. The feed to the coal concentrate thickener comprises the undersize produced by dewatering the Diester table concentrate on 5-mm dewatering screens and the overflow produced by cycloning of the froth flotation concentrate. At the time of testing these filters were inoperative because of the difficulties in filtration, arising from contamination of the

Jan 1, 1962

By George Scott

MANY requests for information as to the possibility of washing coals to some predetermined percentage of ash or sulfur have suggested that the producers aim to satisfy some degree of purity set by the user of the fuel, rather than to attain the greatest economic benefit to all concerned. This paper is written to show that the highest economic purity of washed coal can be determined from washability studies of the raw coal, costs of mining and washing coal, and data on the effect of ash and sulphur on the value of the coal for the particular use for which it is intended. COKE FOR BLAST-FURNACE USE For purposes of illustration, we take the case of coal washed for coke to be used in the iron blast furnace. The method outlined can be made general in its application by substituting for the figures used here the actual operating figures for the particular case under consideration. In general, it costs the blast-furnace operation from 8 to 25 c. per ton of pig iron to slag out each 1 per cent. of ash introduced into the blast furnace by the coke. This figure depends on which one per cent. of ash is removed, and decreases with decrease in ash: When blast furnaces and coal mines are considered as a whole, the figure decreases to zero and then becomes negative, on account of low recovery of washed coal. Various figures1 have been given by different investigators: These figures necessarily differ, not only on account of the differences in operating costs but on account of the difference in the respective fuels as well. For the purpose of this paper, which, as explained, is to point out a method of attacking a certain problem, the figures used in the exposition of the method are of secondary importance. It is apparent that no universally applicable figures can be used, because there are none. Each plant has its own coal,2 its own operating cost, and its own conditions.

Jan 1, 1929

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75' to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.' The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954

By Edgar L. Collis

NO industry or group of industries is more deeply interested in the influence exerted by atmospheric dust than that concerned with the getting of coal and of metalliferous ores. The coal miner in the past has mainly been interested on account of the part played by coal dust in the occurrence of explosions; but investigation is revealing that coal miners experience, at least on certain coal fields, unduly high mortality ascribed to lung diseases, some part of which may reasonably be attributed to dust inhalation, and that a small group of men employed in sinking shafts and driving roads through sandstone rocks experience troubles identical with those that afflict many metalliferous miners. Coal Mining The Registrar General for England and Wales issues information every 10 years concerning the mortality experienced in various industries. The records dealing with coal mining are of particular interest, since they are given separately for each of the largest fields. When examined they exhibit the coal miner with a favorable death rate on the whole when compared with all other occupied males; but they reveal great differences on the different fields; thus the Lancashire miner in 1900-2 had a comparative mortality from all causes of 1006 as against a figure of 675 for the Nottinghamshire and Derbyshire miners, and in 1910-12 of 941 as against 570 for Nottinghamshire. When mortalities due to four only of the great causes of death are subtracted from the total the differences are greatly reduced; these four causes are phthisis, pneumonia, bronchitis and accidents. Thus for 1910-12 more than one-half of the mortality in Lancashire, 478 out of 941, is so accounted for, but less than one-third of the mortality in Nottinghamshire, 184 out of 570; the latter fraction compares with that for all males, 293 out of 790. Exactly why the accident mortality varies thus with those for the lung diseases has not been determined; the fact, however, points to an interesting association between health and so-called "accidental" occurrences.

Jan 1, 1927

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Gloyd M. Wilkes

The eastern section of the Park City district is drained to an elevation of 6300 ft, by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft, in Park City Consolidated Mines Company's property. When development below the 900-ft. level was commenced, sinking was attempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite outside the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking progressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft. of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been developed only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the great amount of water encountered when the fractured zone was intersected. The ground in the fractured zone is so finely crushed that it precludes any possibility of economic support when it is wet. Furthermore, mining costs were found to be prohibitive after caving of vein walls had taken place as a result of an attempt to drive drifts before complete drainage had been effected. More than 3000 gal. per minute was pumped from the 1200-ft. level and the water table remained 75 ft. above this plane even after five crosscuts were driven to the fractured zone at 50-ft. intervals along the strike of the fissure from a footwall drainage drift. It was evident, therefore, that complete drainage must be effected before the fractured zone could be opened in any future development. After extensive investigations in this connection, a well-drilling campaign was decided upon to effect drainage of the fissure in advance of sinking and level development, so that all mining operations would be carried on in dry ground. Drilling Procedure A crosscut was driven through the hanging wall of the fissure on the 1050-ft. level, which was the deepest dry level at the time, to a predetermined location from which a vertical hole should reach the fractured zone at about 400 ft. below this level. A drill station was made and a raise was driven over the location for the hole, to act in lieu of a derrick or drill tower. This raise

Jan 1, 1943

By Dr. O’Neil Thomas J., Donald W. Gentry

"There are two characters to the value of mining properties-one mine may have a value, owing to its real intrinsic worth; an- other (having no intrinsic value) may have a value by being so situated as to harass the working of the really valuable mine-in mining camps one is looked upon as much of ligitimate enterprise as the other.'' -Victor Clement to Simeon Reed, Wardner, Jan. 11, 1890, Reed Mss. APPROACHES TO VALUATION Value and costs are two terms basic to financial analysis which cause, perhaps, the greatest amount of misunderstanding in mine valuation studies. When discussing the value of an asset or the costs of producing a product, it is absolutely essential that the speaker define the terms being used. There are many types of value and many categories of costs. Without specific accompanying definitions, value and cost data are not very meaningful. Value refers to a measure of the desirability of ownership of property. Some of the types of value which might be encountered in a mine valuation study are: 1) Market value 2) Full cash value 3) Salvage value 4) Replacement value 5) Capitalized value 6) Book value 7) Assessed value 8) Insured value Each of these has a specific meaning which can be applied to determine a monetary amount in a specific situation. The major item of interest here is the broader question of "what is the value of the mine?" or "what is the mine worth?" In this case, we are speaking of market value. Market value is the value (price) established in a public market by ex- changes between a willing buyer and a willing seller when neither is under duress to complete the transaction. Market value fluctuates with the degree of willingness of the buyer and seller and with the conditions of the sale. The use of the term market suggests the idea of barter. When numerous sales occur on a market, the

Jan 1, 1984

By R. E. Whippo, B. L. Murowchick

The commercially exploited sedimentary apatites exhibit a number of variable lattice substitutions which affect their chemical composition. Carbonate is a major diluent of phosphorus values in sedimentary apatites. Substantial amounts of water as hydroxyl, hydronium, and tetrahedral hydroxyl ions substitute for fluorine and oxygen, calcium, and phosphate, respectively. Calcium is also replaced by several other divalent and monovalent cations. The structural formula demonstrates the substitutions in the lattice of the sedimentary apatites studied in view of the crystal-chemical relationships which have been postulated for the isomorphous apatite series. The lattice constant a. varies from 9.29 to 9.40 A for the apatites studied. Quantitative relationships between this constant and lattice substitution are complicated by the interaction of multiple substitutions whose influence is non-additive. The mineral apatite, the principal raw material source of phosphorus for agricultural and industrial applications, offers a wide area for investigation. Considerable research effort has been expended in the study of apatite crystal-chemistry by medical, biological, and earth scientists. Few of these studies deal directly with the sedimentary apatites from the major occurrences which are widely exploited for commercial uses. It is the purpose here to present chemical analyses of several sedimentary apatites and discuss their chemical composition in relation to the structural and crystalchemical principles which have been postulated for the apatite isomorphous series. THE STRUCTURE OF FLUORAPATITE The atomic structure of fluorapatite was described, independently, by Ngray-Szabd and Mehmel in 1930 and has been accepted as presented, with only minor changes,4 since that time. The hexaogonal unit cell with dimensions of a = 9.37 0.01 A and c = 6.88 0.01 A contains two molecules of the composition "There are six (PO4) groups in the cell, four calcium ions on the trigonal axes, surrounded prismati-cally by six oxygen ions and six calcium ions surrounded by an irregular polyhedron of a fluorine and five oxygens. Fluorines are at the comers of the reflexion planes, touching three calcium ions each".l7

Jan 1, 1968

By H. R. Hanley, C. Y. Clayton

One of the most important contributions to the art of electrolytic zinc production has been the aluminum cathode. This has been used in all major production since its commercial developmerit in 1916. The literature is replete with important contributions, some of which may have been replaced by better ones, but thus far there appears no other metal to take the place of aluminum as cathode material. Credit for this innovation goes to Sherard Cowper Coles, of England. When experimenting on the extraction of zinc from Broken Hill ore at Hayle, Cornwall, in 1893, he introduced the aluminum cathode, and in 1895 obtained . British Patent No. 20073. The reason for this dominant position of aluminum as cathode material in zinc sulphate electrolytes is its unique surface, to which electro-deposited metals usually do not tightly adhere. The metal must be of high purity for best results. It is possible to develop a starting-sheet method by which thin electro-deposited sheets of cathode zinc are made and stripped from a smooth aluminum plate. Such thin sheets of cathode zinc may be used as are the copper sheets in standard electrolytic copper-refinery practice. However, complications arise because of extreme warping of the zinc starting sheet after a few hours of deposition, and thus special arrangements must be made to compensate for this abnormality. Reasons advanced for the ease with which deposits may be stripped from the aluminum surface are: (1) presence of a permanent oxide coating on the metal, (2) failure of aluminum to alloy with the deposit, (3) differences in coefficient of expansion, (4) high position of aluminum in the electromotive series of metals. Of these reasons for nonadherence, which may have some application in general deposition, probably the oxide coating has the greatest bearing on the subject of zinc deposition. Adherence of zinc deposits has occasionally had serious effect on tonnage and production costs. Opinions have differed as to the specific

Jan 1, 1944

By Morris Cohen

WITHIN the past two years, a number of publications have called attention to the double peaks, or stages, that appear in the hardness and strength curves of certain aging alloys. The author has shown the existence of double hardness peaks during the aging of a high-purity silver-copper alloy;1 and on the basis of electrical resistance, microscopic, dilation and lattice-parameter measurements, he concluded that the initial hardness peak occurs prior to precipitation while the secondary hardening is due to precipitation. It was suggested that the general mechanism of age-hardening involves two consecutive processes, the first consisting of nucleus or knot2 formation, and the second consisting of actual precipitation and particle growth. It was further held that the two stages are interdependent, but because of nonuniform precipitation they may overlap each other to an extent that increases as the aging temperature is raised. At high aging temperatures, the effect of the first stage cannot be detected because of the rapid occurrence of precipitation. The general theory of age-hardening recently presented by Dr. M. L. V. Gayler3 is in close agreement with the picture outlined above. With reference to work done on duralumin, copper-beryllium and copper-silver alloys, Dr. Gayler also concluded that age-hardening takes place in two consecutive steps: first, diffusion (in which the solute atoms migrate to certain crystallographic planes), and then precipitation. However, W. L. Fink and D. W. Smith4 have shown that the double aging peaks that appear in the strength curves of high-purity aluminum-copper alloys may be explained without recourse to pre-precipitation phenomena. By means of very careful metallographic technique, Fink and Smith demonstrated that during aging the precipitation takes place at an accelerated rate along the grain boundaries and slip planes as a result of the plastic deformation caused by the drastic quench from the solution heat-treatment temperature. ? The general precipitation occurs at a

Jan 1, 1938

By Douglas Bunting

IN THE anthracite fields of Pennsylvania, mine fires occur with more or less regularity and their existence is an ever-present hazard in coal mining. In all probability 90 per cent. of the mine fires can be ascribed directly or indirectly to the ordinary miner's open lamp. Other causes may be smoking, electrical installations, gas explosions, gas feeders, and the communication of fire to the outcrops from ash dumps, culm banks, timber and brush fires. Fires in pump rooms, engine rooms, and barns have been largely eliminated as a result of the Act of .Assembly, approved June 15, 1911, which provides that all inside buildings, including engine rooms, pump rooms, barns etc. shall be constructed of incombustible materials. Smoking of pipes, cigars, and cigarettes should be prohibited in the mines and too much care cannot be exercised in preventing fires by enforcing all rules designed for that purpose. Mine fires that involve underground fighting are invariably dangerous, and all fires, irrespective of the method pursued in extinguishing them, involve property loss and expense. Each fire generally presents a more or less original problem, dependent on the particular conditions. Generally mine fires may be divided into two classes: Those occurring in inaccessible workings and those occurring in accessible workings. The methods pursued in extinguishing or controlling mine fires are as follows: (1) direct attack, (2) smothering by sealing, (3) flushing with silt or other solids, (4) flooding with water, (5) cutting off, (6) surrounding with incombustible materials, (7) digging out by stripping from the surface. Most fires are extinguished in their incipiency by direct attack and failure to extinguish by this method is due to late discovery, lack of water, and facilities for fighting, or improper procedure in the initial attack. Should the method first pursued be unsuccessful, careful consideration should be given in determining next the method to be adopted; then the work should be carried on as rapidly as possible and under the supervision f the most competent persons. Materials and supplies should be fur-

Jan 9, 1921

By F. H. Labee

Questionnaires and special letters soliciting information were sent to a great many geologists, petroleum engineers, independent operators, and representatives of large companies in Arkansas, Louisiana, Texas and New Mexico. Replies to more than 50 per cent. of these letters were received. A survey of the facts and opinions presented in this correspondence will be made a little later, but first some of the general aspects of the problem will be reviewed. By "unit operation,"1 we mean the development and operation of a single entire pool, or reservoir, of petroleum by one management, on a systematic and scientific plan which is best calculated ultimately to extract from the pay sand and bring to the surface of the ground the largest possible amount of oil with the greatest possible total profit. No one, as far as the author has been able to ascertain, denies the advantages, both scientific and practical, of unit operation. All are agreed that it is sound in theory. It permits the proper distribution of wells, which should always be spaced on the ground according to a regular geometric plan with the intention of maintaining the same spacing all the way down and into the pay sand, or pay sands. This spacing will be different for different fields, depending on such variable factors as the lithologic character of the pay formation, the nature of the controlling structure, the depth of drilling, the viscosity of the oil, and so on. From the viewpoint of engineering practice, as applied to economical extraction of oil, there is no more important consideration than well spacing—well spacing in the pay formation, and not merely on the surface of the ground —for the method of well spacing has a direct bearing upon all such engineering practices as pressure control, repressuring by gas, the water drive, and SO on. H. C. Miller2 summarized the advantages of an ideal cooperative development plan as follows: "Among the more important advantages of

Jan 1, 1930

By Joseph Sinclair

THE Republic of Ecuador is situated partly in the northern and partly in the southern hemisphere. The equatorial line passes about 11 miles north of Quito, and. divides the country into two almost equal parts. Crossing the equator almost at right angles, and extending from Colombia into Peru, the Andes form a great upland that, in cross-section, resembles a truncated cone, the top of which is about 40 miles wide and about 10,000 ft. above the sea, while the base is about 80 miles wide extending from sea level, on the Pacific Coast, to the Amazon Plain, on the east. Superimposed on this upland are many active and extinct volcanoes, which form roughly two parallel chains of mountains, on the eastern and western boundaries, respectively, of the plateau. These are often referred to as the Eastern and Western Cordilleras of the Andes, although their parallelism is somewhat. questionable. The highest of these mountain, masses is Chimborazo, about 21,000 ft., above the sea; among the others is the volcanic peak, Cotopaxi, rising to about 18,000 ft. above the sea. The development of the petroleum resources of Ecuador is greatly affected by this Andean mass, not only .because of its composition and geological structure but because of the barrier it interposes between the lowlands on the Pacific side and whatever part of the Amazon Plain to the east is finally found to belong to Ecuador, for the eastern boundary of the Republic is still in dispute with Peru. To understand, therefore, the development of the petroleum reources of the Ecuador and the barriers to such development, we must bear in mind the three great physio-graphic divisions, viz., the Pacific Coastal region on the west, the Andean Plateau in the center, and the Amazon Plain on the east. The first important effect of the threefold physiographic division is that Ecuador has two sets of petroleum regulations: one for. that portion east of the Andes, and one for the Andean Plateau and the Pacific Coastal region although it is probable that the two sets of regulations are, in part, 'due to the boundary dispute with Peru.

Jan 3, 1924

By D. Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abun¬dant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleis¬tocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional re¬sources. Limestone uses include cement and lime manufac¬turing, concrete sand and aggregate, road base material, beach sand replenishment, agricultural lime, and golf course construction.

Jan 1, 1984