Search Documents

By L. M. Cathles, W. Joseph Schlitt

A mathematical model describing the leaching of low grade industrial waste dumps in developed and solved by finite difference techniques. The leaching behavior of model dumps of different sizes, permeabilities, and waste characteristics, under different operating conditions, is then investigated using the model. It is shown that leaching is fastest for dumps 50-100 feet (15-30m) high, that permeability is very important for the effective leaching of large dumps, that slow leach kinetics of the waste may not be detrimental, and that the leaching of large dumps may be facilitated if leach solutions are preferentially applied to the hot, near-edge portions of the dump.

Jan 1, 1980

By Adrian Brown

INTRODUCTION The primary tool which is available to improve the stability of an open pit mine at a given slope angle is control of groundwater pressure. This paper sets out the methods by which water pressure control can be achieved in large mines in different materials. The emphasis of this paper is on large mine slopes because. these slopes exhibit the greatest need for groundwater control, the greatest economic benefit from groundwater control, and the greatest technical challenge in achieving groundwater control. STABILIZATION USING MTER PRESSURE CONTROL Groundwater pressures reduce the stability of slopes in two fundamental ways, as shown schematically in Figure 1. In the example, a horizontal failure surface intersects a vertical joint or weak zone. Water pressure acts: o On the base plane to reduce the normal force on the sliding surface and hence reduce frictional resistance to sliding, and o On the vertical back plane, to create a driving force for the system.

Jan 1, 1983

By D. K. Atwood

Experiments resulted in a satisfactory laboratory method for restoring permeability to clay-containing cores damaged by fresh water. Clay contents of a number of field cores were measured, and permeabilities of plugs from these same cores were then deliberately reduced with fresh water. This damage is attributed to swollen and dispersed clays occupying the pore space. After damaging, a number of experiments were performed to meaJure the amount of damage and to establish some means by which permeability could be restored. The experiments included flooding the damaged cores with water-miscible fluids such as salt water, acetone, isopropyl alcohol and ethanol. Permeability was not successfully restored in these experiments. However, part of the damage was repaired by flooding with oil; when water was removed by distillation in the presence of immiscible fluids such as air or toluene, permeability was completely restored. This evidence suggested that swollen and dispersed clays could be collapsed to their original volume by strong interfacial and capillary forces. It was further postulated that the required forces could be generated by flooding the damaged cores with a solvent partially miscible with water. The flooding experiments were repeated using n-hex-an01 as the partially miscible solvent. Permeability was restored to five of six damaged cores and substantially increased in the sixth. A large fraction of the restored permeability was retained even after water saturation was raised to its original value with 12 per cent salt water. INTRODUCTION Sharp reductions in permeability often occur when relatively fresh water contacts clay-containing formations during drilling and workover operations. These permeability losses are caused by removing inorganic ions from the environment surrounding the clay, and consequent swelling and/or dispersion of clay minerals into the available pore space.' This phenomenon is generally termed clay damage, fresh-water damage, or simply formation damage; it causes large losses in current revenue by preventing oil wells from making their allowable production. Attempts to repair the damage and restore permeability by flowing salt water solutions or brines through clay-damaged cores containing montmorillonite have been unsuccessful.' This irreversibility is thought to result from formation of brush-heap, or edge-to-face, structures when the dispersed clay is flocculated. The brush-heap structures occupy much more space than the close packed domains present before damage.' One solution of the problem is to destroy the clay-water brush-heap and thus restore permeability. Because no satisfactory method existed for restoring permeability to clay-containing formations damaged by fresh water, the work described in this paper was under taken. The laboratory experiments generally consisted of deliberately damaging fresh cores containing clay and then attempting to repair this damage by various means. Results indicate that generating strong interfacial forces within the pore space of damaged cores collapses the clay brush-heap and restores permeability. These forces are most conveniently generated by flowing partially water-miscible solvents, such as n-hexanol, through a core. THEORY OF THE DAMAGE PROCESS The most common clay mineral groups known to cause permeability damage to formations are the mont-morillonites, kaolins, chlorites and illites. These clays are constructed of particles which can adsorb water on their surfaces and edges and, in the case of montmorillonite, between layers of the basic particle itself. This adsorption increases as water salinity decreases. At low salinities the particles disperse into the aqueous phase. When the clays present in the formation are kaolin, chlorite and illite, dispersion accounts completely for permeability damage to porous media. However, unlike the other clays, montmorillonite particles can imbibe water and adsorb ions between layers of sub-particles, or platelets. These platelets have net negative charges on their faces and are held together by exchangeable (or removable) cations such as Na and Ca decrease in ion concentration (salinity) in the fluid surrounding a particle causes migration of water into the clay layers and disperses the basic particle, while diffusion removes the original exchangeable ions from between the platelets. Once these ions are removed, the facing negative platelets repel each other, causing the montmorillonite to swell until, for all practical purposes, the individual platelets are dispersed. For this reason, fresh-water* damage is much more severe in sands containing montmorillonite than it is in sands containing other clays. Many investigators have shown that even trace amounts of montmorillonite can be responsible for marked reduction in the permeability of reservoir sands in the presence of fresh water." ." Monaghan and others have shown that fresh-water damage in montmorillonite-containing cores cannot be

Jan 1, 1965

By H. L. Stone, A. O. Garder

A numerical method of solving the partial differential equations which describe the one-dimensional displacement of oil by gas has been presented. Possible extension of the method to treat multidimensional flow is discussed, and the limitations of this extension are indicated. Using this method, it is possible to allow for the existence of a gas cap, the presence of any number of gas-injection or oil-production wells and the evolution of dissolved gas from the oil. It is also possible to allow for variation in the cross-sectional area, elevation, porosity and permeability of the reservoir. The influence of relative permeability and the force of gravity in the direction of flow upon the displacement is considered. The influence of capillary pressure upon the flow and the effect of gravity in the direction perpendicular to flow are neglected. The physical properties 01 the fluids are considered to be Junctions of pressure only, and equilibrium between contiguous phases is assumed. The numerical calculations can be readily carried out by the use of a digital computer. Several example analyses have been performed using the IBM 704 computer, and about one-third of an hour of computing time was required per case. Reservoir behavior predicted by use of this numerical method was compared to data obtained by other methods for three cases — complete pressure maintenance, dissolved-gas drive and gas-cap drive. The independent solutions to these problems were obtained by analytical solution, laboratory experiment and field data, respectively. Agreement of the numerical solution with data from these sources was good; this agreement establishes the convergence and accuracy of the numerical method. INTRODUCTION Most petroleum reservoirs can be produced by any one of several alternative programs. When a reservoir is produced by primary methods, production economics can be influenced by controlling the number and location of wells and the flow rate of each well. An even greater influence may be achieved by augmenting the recovery of oil obtainable by primary methods. This can be accomplished by injection of fluids such as water, natural or enriched gas or a bank of light liquid hydrocarbons. Selection of the most desirable operation requires a means of predicting the reservoir behavior which will result from each of the several alternative programs. The purpose of this paper is to present a mathematical method for predicting the behavior of reservoirs produced by gas-cap drive, dissolved-gas drive or pressure maintenance by gas injection. The method described herein takes cognizance of phase changes caused by a decline or an increase (due to gas injection) in reservoir pressure, of the presence of a gas cap and of the effect of gravity on the flow of gas and oil. Relative permeability relationships are used to define the flow properties of the rock. Allowance is made for variation in cross-sectional area, elevation, permeability and porosity of the reservoir. Both the influence of capillary pressure upon the flow and pressure gradients in the gas cap are neglected. Whenever a liquid phase and a gas phase are in contact, they are assumed to be in equilibrium. The physical properties of the fluids are considered to be functions of pressure only. Therefore, if the method is to be used to predict the effects of a gas-injection program, mixtures of the injected gas and formation crude should-have the same physical properties as mixtures of formation gas and crude. The equations to be presented in this paper apply only to a one-dimensional case; therefore, they neglect the influence of gravity in the direction transverse to the flow. As is well known, this gravitational influence may lead to overriding of oil by gas. Consequently, this procedure as presented is most applicable to long, thin reservoirs for which gravity overriding is not important. On the other hand, the equations presented can be generalized to treat multidimensional flow and, hence, to consider gravity overriding, if desired. A word of caution on two points is advisable here, however. First, the authors have not demonstrated the accuracy of the numerical technique for multidimensional flow. Second, and more important, capillary pressure will often be of importance in multidimensional problems. Obviously, in such cases a generalization of the

By R. H. Richards, C. E. Locke

In "Sorting Before Sizing " (a paper first announced at the Pittsburgh meeting, February, 1896, but delayed in preparation and now presented at the present meeting) it is shown that if slime-tables are to do their best work on slimes below 0.5 mm. or 0.05 inch in diameter, they must be carefully sorted or classified, and fed to a series of tables suitably adjusted to the different slime-sorts. The reason is that the coarser and finer slime-sorts require respectively different adjustments of the tables. Hence, if the two are fed together upon a table which has, as nearly as may be, average adjustments, fine galena, for example, will go into the tails, or coarse quartz into the heads, or both—losses which could have been largely prevented if the slime had been carefully sorted and each sort sent to its own slime-tables. As indicated in the paper just mentioned, the present tendency in this country is generally to do away with slime-sorting or "classification," and simply to take the overflow from the hydraulic classifier and divide it among the tables by means of

Jan 1, 1898

By R. E. Zimmerman, Shiou-Chuan Sun

An evaluation of the mechanism surrounding the froth flotation of coarse coal and mineral particles as a result of experiments conducted at The Pennsylvania State College. Maximum size ranges for both bituminous and anthracite coals were established as well as the factors affecting the floating of coarse particles.

Jan 5, 1950

By Charles Baskerville

Shales containing "kerogen," or bituminous matter, which on destructive distillation yield oily and tarry matters resembling petroleum are here designated as oil-shales. They differ from oil-bearing shales from which petroleum may be obtained by so-called mechanical means. The educts obtained by the destructive distillation resemble some or all the varieties of petroleum, depending on the character of the shale and the mode of treatment. Some shale oils have a paraffin base, some an asphaltic base, or a combination; some run high in sulfur compounds. The methods of refining and cracking, therefore, are essentially the same as are used in refining petroleums. In 1860, in this country, over fifty companies were successfully distilling various natural bituminous materials for the production of " coal oil," used for illuminating purposes. The discovery of petroleum and the failure of these companies to save and utilize the valuable byproduct, ammonia, brought about their inevitable doom. Prior to that time, more or less successful efforts were made to produce from the shales of Scotland oils for illuminating and heating purposes. Competition of native petroleum from the United States early eliminated some of these companies and with the entrance of oil from the Russian and other fields into the world's markets, the Scottish oil-shale industry underwent serious and trying experiences until, in 1916, only four (Scottish) were paying concerns. These survived only through energy and the application of skill in saving valuable byproducts. A few companies have successfully operated in France and New Zealand. The Canadian Government showed active interest in the New Brunswick shales, which exist in quantity and are more valuable than the Scottish shales. The retarded development of that valuable asset of the Province of New Brunswick was most unfortunate, especially when the product was so much needed in the prosecution of the war. The economic success of a shale-oil industry depends on the following factors:

Jan 1, 1921

By John Porter

THE requirements of the standard specifications under which Portland cement is sold have materially increased within the past 10 years, but practically all companies are now furnishing cement better than these requirements; in some cases exceeding them by nearly 100 per cent. From a sales standpoint, it is desirable to have a product that is uniform to a high degree and free from occasional quality troubles. A failure in quality, even if it affects only a few hundred barrels out of a yearly output of a million or more, is apt to be talked about in the trade and to affect the salability of the entire output. For these reasons, there has recently been great activity along the lines of quality control and improvement; and some of the most interesting problems of the industry are in this field. From the manufacturing standpoint, the quality of cement is chiefly a matter of uniform and proper chemical composition of the raw mix fed to the kilns plus proper burning in the kilns; the fineness to which the cement is ground, the proportions of gypsum, the method of seasoning, and the like are contributory factors. Uniform chemical composition of the raw mix has been one of the most difficult problems to solve. Most plants will use from 1000 to 3000 tons of rock per day and in but few cases is this material as it lies in the quarry even approximately uniform in composition. The problem, then, is to quarry and mix this raw material in such a manner that every handful passing through the kilns will have practically the same analysis as every other handful. To accomplish this purpose there are two methods of preparation: the wet process and the dry.

Jan 1, 1925

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By Morgan Walker, C. D. Watson, Reid W. Bond, D. L. Trax

Common practice in the Mid-Continent until recently was to prolong the natural flow of oil wells as long as possible by agitation, and then swab for a short period until the well was put on the pump. Comparatively recently the gas-lift has superseded the swabbing and agitating period and in some cases encroached on the natural flowing life, particularly where it was evident that the potential oil capacity of the well was greater than the gas supply, or lifting medium. The majority of wells are finished with either 6¼, 65/8 or 8¼-in. casing and connected to a separator through a flow line which is usually 65/8 in. The flow line is generally designed to eliminate sharp turns and has reduced the gas-oil ratio and therefore increased the efficiency in a good many instances. Until recently all wells were allowed to flow without restriction against the possible trap pressure until it was deemed advisable to put them on gas-lift. This resulted in a fairly efficient flow during the early life of the well if the well was rather large but was usually inefficient in small wells and in the later flowing life of large wells, on account of the large area in the casing and therefore excessive slippage. Recently, considerable effort has been made to increase the efficiency of small flowing wells by running tubing to eliminate as much slippage as possible. With large wells there is a considerable trend toward back-pressuring, or beaning to find out whether it is possible to reduce the gas-oil ratios and increase the flowing life. The greater number of fields that have been back-pressured have been produced in that manner through necessity, either to restrict production for proration purposes or, in fields producing by hydraulic pressure, to reduce water encroaching. The recent Cromwell sand development in Little River is an example where both back-pressuring by means of high-pressure traps and beans and flowing through tubing were used to conserve gas, reduce the high gas-oil ratio and prolong the flowing life. It

Jan 1, 1930

By T. M. Geffen, H. N. Hall

One-third to one-half of the original oil is left in most reservoirs even after thorough gas driving or waterflooding. In contrast, essentially all of the oil contacted con be recovered by flooding with a solvent (a fluid miscible with the reservoir oil). It is not economical to fill a reservoir with solvent since the value of the solvent would very likely exceed that of the oil. A practical method would be to inject a small bank of solvent to displace the oil. This solvent bank in turn could be driven through the rock by a less valuable scavenging fluid, such as natural gas which is also miscible with the solvent. Such a method of oil recovery was studied in the laboratory using long (up to 95 ft) core systems. It was found that, as the solvent moves through the reservoir, the front end of the solvent bank becomes mixed with the oil and forms a relatively short mixing zone between undiluted crude oil and pure solvent. An engineering correlation was obtained which can be used to predict the length of this zone. Displacement of the solvent by natural gas can be achieved with complete miscibility (above the critical pressure of the gas-solvent system at reservoir temperature) or with partial miscibility at lower pressures. Under conditions of complete miscibility, it was found that the length of the gas-solvent mixing zone could be predicted from the correlation developed for the solvent-oil mixing zone. With partial miscibility, two phases exist and the solvent is displaced by a modified gas drive in which vaporization and condensation occur. Equations are developed to predict the performance of this type of displacement. Two plans are suggested for application of miscible fluid displacement. one for miscible displacement of the solvent and the other applying to lower pressures where partial miscibility occurs during solvent displacement. Calculations based on the laboratory tests indicated that a bank of solvent with a volume of less than 10 per cent of the hydrocarbon volume under consideration will generally be adequate to obtain high oil recovery from the portion of the reservoir contacted in miscible fluid displacement. INTRODUCTION The conventional methods by which oil is displaced from reservoir rock—solution gas drive, conventional gas drive, and waterflooding—are all processes in which the oil is expelled from the rock by direct displacement with a fluid immiscible with the oil. Because of the immiscible type displacement, complete recovery of the reservoir oil is not achieved. In economically successful flooding operations, as much as 50 per cent of the original oil may be abandoned in the reservoir as unrecoverable. The use of a solvent (miscible with oil, such as LPG) as an injection fluid does not have the undesirable displacement features common to the use of gas or water (immiscible with oil). It can be readily appreciated, however, that it would not be economically feasible to displace the oil and entirely replace it with a solvent. A process was therefore devised for use in field operations in which only a small volume of solvent would be required to obtain essentially complete oil recovery in the portion of the reservoir contacted. In this process, the solvent acts as a buffer between the reservoir oil and injected gas, allowing the natural gas to displace indirectly the oil with much greater efficiency than if the gas displaced the oil directly. DESCRIPTION OF OIL RECOVERY PROCESS The solvent oil recovery process will be described in

Jan 1, 1958

By E. B. Fitch, E. C. Johnson

The operating behavior of liquid-solid cyclones is outlined, together with the nature and range of the process results obtainable, to serve as a background for engineers wishing to consider application of this new process tool. BY now most engineers are familiar with the liquid-solid or Dutch State Mines cyclone. However, it should be helpful to know exactly what it is that the equipment does and what its limits are. Without going into cyclone theory, this paper will describe the operating characteristics of Dutch State Mines cyclones. These are manufactured under license in this country and sold under the trade-marked name of DorrClone. The physical construction of the liquid-solid cyclone has been covered in many papers,'-' the DorrClone in particular being described in some detail by Weems. Fig. 1 shows the unit in cross-section. The feed enters at C. The coarse, heavy particles are thrown centrifugally to the periphery and make their way down the wall to the apex where their rate of discharge as underflow is controlled by an adjustable rubber apex valve. As the apex diameter is decreased the solids build up behind the valve, producing a denser underflow. Meanwhile the fine particles are swept into the upward flowing vortex stream which exits as overflow through the vortex finder, F. Flexibility to produce the specific result desired in a particular process is achieved by providing means for varying the areas of the entrance, vortex discharge, and apex discharge. The entrance area may be varied by insertion of special shims. Vortex discharge area may be changed by use of different-sized vortex finders which are interchangeable. Similarly, the different sizes of apex valves are interchangeable and in addition each apex valve is variable down to about 60 pct of its maximum diameter. A most significant primary distinction to make is that although liquid-solid cyclones have been sometimes called thickeners, they actually are classifiers, and very potent ones. They are almost never thickeners in the special sense that many metallurgical engineers understand the term. There would be no profit in quibbling over the definition of a word, but when the application of cyclones is considered, it will help to understand the difference be- tween two mechanisms, one of which will be called classification, and the other thickening. In what is called thickening the fine solid particles present in the feed hold together by surface attraction during the sedimentation process. The loose network of particles thus held together constrains all particles to settle at approximately the same rate, the larger ones dragging the smaller ones down. As a result, pulp settles with a sharp line of demarcation between solids and a relatively clear supernatant liquid. Essentially all the solids, regardless of their fineness, pass into the thickened underflow, and a clear overflow is separated. In classification, on the other hand, the interparti-cle forces are relatively insignificant as compared to the settling force on the individual particles, and are insufficient to prevent independent movement of the particles. The coarsest, heaviest particles settle most rapidly through the pulp, passing more slowly settling fines. Particles coarser than the mesh-of-separation essentially all settle into the underflow, but if the feed contains any particles finer than the mesh of separation, at least part of them will appear in the overflow. A clear supernatant or overflow can be obtained only if there are no undersize particles present in the feed. Thus it will be seen that classification is impossible under ideal thickening conditions. The finer particles are pulled down at essentially the same rate as coarser particles, and there is no separation on the basis of particle size. The surface attraction holding the particles together in a thickener is usually feeble. Whenever the sedimentation force on any particle is strong with respect to the interparticle forces, that particle can pass through the tenuous structure and settle independently. There are at least four ways of making the sedimentation force strong, with respect to the interparticle forces, and obtaining classification. First, and most obvious, the particles may be large and heavy. Thus coarse sands settle out in a beaker or Dorr thickener ahead of the rest of the thickening solids. Second, the interparticle forces may be altered by physicochemical means; i.e., it is often necessary to add dispersing agents to destroy the interparticle forces and permit classification to take place. Third, the interparticle forces may be reduced by dilution of pulp. It is well known that to obtain the most efficient separation of

Jan 1, 1954

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

Little information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's," ' Kick's,%nd Bond's' theories. Theories by Bond and Wang," Lineau,' Hatch,' Roller," and others were not considered applicable. Those used in this investigation may be expressed mathematically as follows: [ ] The above equations were employed to determine values of KK, K for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement.

Mar 1, 1956

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the-indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer, or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made . . .

Jan 1, 1943

Jan 1, 1949

By Percival Roberts

It may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time * the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or pnddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By Strathmore R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer' stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,' Mitchell et al.,3 and particularly Hamilton et al." have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski's French Patent No. 847,- 215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores.

Jan 5, 1960

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922

By H. M. Roche

MAGNETITE is the important iron ore of New Jersey although bog ore, limonite and red hematite were mined in sizable quantity early in the state's min-ing history. The deposits of mag-netite are found in the Highland area in the northern part of the state. These ores outcrop a broad belt 20 miles wide, extending in a northeasterly direction from Phil-lipsburg, on the Delaware River, to Greenwood Lake, at the southern boundary of the state of New York, a distance of 60 miles. The area in which the magnetite is found (see map, Fig. 1) contains 1200 square miles and the center of the area is at Dover, 40 miles west of New York City. In the general area are found 18 parallel ranges or lines of ore deposits. These ranges may be re-garded as mineralized zones in which occur orebodies that are rich enough in magnetite to war-rant mining. Usually a number of the orebodies lie one above the other in the same plane, all dipping and pitching in the same direction. Within the ranges, there may be several parallel orebodies of work-able size. The average strike of the orebodies is N.41° 30' E., with an average dip of 55° southeast and an average pitch of 15 ° to the northeast. Orebodies suitable for mining range from 6 to 100 ft. wide, as measured from foot wall to hanging wall. Their heights, as measured on the dip and normal to the long axis of the orebody, vary from 200 to 3,000 ft. The length along the pitch has never been determined by mining, al-though several of the orebodies have been worked to lengths of 10,000 ft. The grade of the ore as mined today varies from 30 to 60 per cent iron, and the gangue min-erals are chiefly silica, alumina, magnesia, lime and phosphorus.

Jan 1, 1937

By Owen R. Rice

Changes in coke hardness affect the working of the blast furnace, for soft coke is an obstacle to proper furnace operation. Soft coke is due to a low hydrogen-oxygen ratio in the coal charged; increasing this ratio increases the hardness of the coke. The best means of determining the hardness of coke is the combined tumbler and ball-mill. What is Good Coke? It is not always appreciated that the correct answer may be such a reliable forecast to the physical condition of the blast furnace, and incidentally its entire operation, that among the ordinary variations in other raw materials and also in operating conditions, it assumes a position of primary significance. Inasmuch as coke forms two-thirds of the total bulk of material charged, this assertion will not seem exaggerated, and in the subsequent discussion its applicability will be presented. Coke is the ideal blast-furnace fuel because it is strong and hard enough to resist the crushing and grinding effects of the furnace burden, and its porosity allows the ready passage of gas upward through the charge, and rapid combustion before the tuyeres. Coke deprived of its strength and with a cell structure physically frail and chemically susceptible to solution by carbon dioxide has its chief asset eliminated. When the melting zones are approached the fluid cinder trickling toward the hearth will envelope the small pieces of coke and form a sticky mass that will retard the free passage of gas. Blast pressure will then rise, driving will slow up and fragments of coke will lie inert before the tuyeres, rendered practically incombustible by their slaggy envelop. It is believed also that coke messes at cast are attributable to quantities of such coke floating unburned in the hearth. It has been correctly claimed that coke rendered small outside the oven possesses greater combustibility than that so developed in the

Jan 1, 1922