Search Documents

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a common occurrence in coal mines of the Northern Appalachian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and formation of cutter roof failure. In-mine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dikes registered the greatest amount of roof loading near the intersection of dikes with the rib. Load cells measuring horizontal pressure changes in the roof indicated that the greatest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysis of rock pressure monitoring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectively support the roof in areas of clastic dikes and prevent cutter roof failure. However, these methods were only successful when employed shortly after mining.

Jan 1, 1984

By M. Katzer, R. Klimpel, J. Sewell

The effect of using selective dispersants as wet grinding aids for ores is demonstrated on laboratory scale batch and continuous grinding equipment. A complete characterization of behavior is performed on a given ore to demonstrate correlations involving torque, % solids, net production rate, and slurry weight and volume loading. The relationship between such laboratory data and industrial scale testing results is very consistent.

Jan 1, 1982

EDUCATION is a business; and, if the consumer is satisfied with the product, no one has any grounds for complaint. "Pretty well satisfied" about slims up the attitude of the mining industry toward the young graduates presently entering the field. Yet, with amazing regularity the controversy over the five-year curriculum recurs in educational circles. The educational mills grind out their products, some higher grade than others, depending on individual proclivity. The cycle continues almost without interruption. Arthur Taggart, however, takes his bowie knife to some of the sturdiest limbs of the tree of knowledge in his article on engineering education on page 770 of this issue. As all who know him might suspect, the pruning is not restrained. With one swing of the knife, such practically-labeled courses as Mine Design are stricken from the tree and transplanted to the field of Graduate Education. Emphasis on the basic sciences and the study of man through courses in history, economics, and literature are recommended to constitute an undergraduate curriculum. Such courses show the least depreciation and therefore give the student the most for his money. Partial justification for this dramatic departure from tradition is explained by the increasing number of companies giving training courses. Why make the student pay for what he can get paid for learning after graduation, the author argues. Other leading educators espouse this doctrine. Dean S. C. Hollister of Cornell, for the Committee on Adequacy and Standards of Engineering Education, recommended to ECPD in 1951 that emphasis be placed on the basic sciences. "Sifting back through the curriculum, it seems clear that instruction in the basic sciences, if taught in a manner such that knowledge of them makes available working tools, contributes the most sustaining part of the curriculum", reported the committee. Note that he would utilize practical problems from the fields of engineering in teaching the sciences. In our opinion the important thing to learn in college is how to think the engineering approach. Recitation on traditional solutions of classic problems sharpens the memory, not the ingenuity of the student. The engineering schools of the nation recognize the advantage of great emphasis on fundamentals, and the inclusion of cultural courses in the curriculum. However, industry presently requires graduates to have a substantial knowledge of the tools of the trade upon graduation. This means that the colleges are forced to pare to the bone to encompass the required studies in the time allotted. In addition, there is the limitation of student money. College educators also claim that entering freshmen are often improperly prepared in such subjects as writing and mathematics. These considerations make it difficult for the critic of the engineering graduate to make any headway with the educators. Actually with the mounting problems imposed by lower grade and more complex ores, a new breed of engineers is needed. The impetus for this new product must come from industry. If there was a concerted effort from industry for an improved type of engineer, the colleges would modify their aims to meet the demand for the kind of individual desired.

Jan 1, 1952

By Thomas N. Williamson, Victor Zeni

A 6-ft diam core drilling machine has successfully completed seven mine shafts in Virginia and West Virginia to depths as great as 465 ft. There is no practical depth limitation to this new system-a potential method in formations not easily penetrated with other large-scale drilling programs-and higher penetration rates and larger diameters are possible in some formations already being drilled successfully by other methods. The core barrel on the machine is fitted with rolling cutters such as those used on oil field rotary bits, so that less torque is required than with other large- scale drilling systems. The core is made with a wider kerf than is achieved with other coring methods, providing more working room for core drilling.

Jan 4, 1957

By V. S. Swaminathan

This year, Great Britain is looking back over a century to August 14, 1850, the day when the first "Act for the Inspection of Coal Mines" was passed in that country, an act which signaled the end of over two hundred years of hitherto uncontrolled and dangerous mining practices. It was back in the time of Queen Elizabeth that . thousands of pounds were invested in mining, particularly coal mining in England and Scot- land. By 1640 there were collieries producing 10,000 to 25,000 tons of coal per year. In the seventeenth century the Tyne district coal industry was organized into powerful partnerships, and coal took an even larger part in industry, as a source of power and as fuel for the iron industry. In the early 19th century a "phenomenal, almost devastating expansion" characterized Britain's coal industry, and it was sparked by a 111 pct in- crease in the population of England and Wales in the first half of the century. Coal production for those 50 years increased 470 pct and pig iron production was up 946 pct for the period 1801-51.

Jan 1, 1950

By F. L. Ransome

The dike here described is exposed in the workings of the Wedge and Bachelor mines, on the southern side of Red Canon, north of the town of Ouray, Colorado. Its course is north 80° east, or nearly east and west, and it hades to the north about 10°. It rarely outcrops, and was nowhere seen at the surface near the mines. A specimen collected by Dr. A. C. Spencer about two miles to the westward, near the mouth of Red Creek, indicates, however, a probable exposure of the dike near this point. The Wedge and Bachelor mines lie in a nearly horizontal series of fine-grained, light-grey sandstones, alternating with beds of very fine-grained shale of the same color. The shale as encountered underground is unusually compact and massive, but weathers readily on exposure, and splits much after the manner of ordinary shale. When fresh it closely resembles some finely arenaceous limestones, but it does not effervesce with acids, and is eseentially a fine, indurated, siliceous silt. Near the surface, and near the top of the sedimentary series as

Jan 1, 1901

By E. H. Lancaster, M. E. Mitchell

A MUD-conditioning program found to be very effective for drilling and completion operations on routine field wells requiring relatively short drilling time involves a moderate alkaline-tannate-bentonite treatment resulting in an ultimate filtration rate of 10.0 cc or less (API test). Mud weight schedules are planned from pressure information on completed wells in producing reservoirs and drill-stem test data obtained on other zones not being produced at present. In general, terminal mud viscosities average 45 sec (Marsh). This value has been found to be sufficient to remove cuttings from the well bore on the average well, with the slush pumps in general use on the rigs. On field wells requiring drilling times in excess of approximately 30 days, an alkaline-tannate-lime-bentonite treatment has been effective in maintaining desirable viscosities and filtration rates with a substantial reduction in chemical costs. This system has shown particular advantage on heavily weighted muds and those with abnormal flow-line temperatures. For the most part, the chemical treatment utilized in wildcat drilling follows closely the program used on field wells, depending on depth and duration of drilling operations. Wildcat mud programs are planned from information available from various geologic and operational sources, taking into consideration the possibility of encountering mud problems of a special nature in the wildcat area. Careful planning of wildcat mud pro- grams has proved to have definite value in avoiding most serious mud problems. An analysis and recommended treatment are presented on several special. mud problems which have been encountered in the area in the past. Those problems discussed are lost circulation, blowouts, sloughing shale, excessive chloride contamination, sulphate contamination, and prevention and correction of cement contamination. Introduction Drilling-mud control in the Southwest Texas area, in general, does not involve the multiplicity of problems encountered in other coastal areas. For instance, it is rare that a mixture of problems such as lost circulation, abnormal pressure, severe sloughing shale, and others, occurs on one well within close enough limits in vertical depth not to be taken care of by a sensible casing program, together with a relatively clear-cut mud program. There are conditions such as the fairly widespread occurrence of abnormal pressure in the lower Frio and Vicksburg zones, and the tendency for sloughing shale in the Jackson section which make for rather expensive mud control. However, the availability of fairly accurate geologic and operational information makes possible a reasonable degree of standardization on mud treatment over a relatively large area. It may be said that, over most of this area where drilling is currently in progress, the natural mud made is very poor in quality, but responds readily to moderate chemical treatment to yield very good wall-building characteristics. AS far as field development drilling is concerned, the mud engineer's principal job, once the routine treatment best

Jan 1, 1949

By N. Brown, M. Herman

IT has been pointed out by Cottrell' and Fisher that long-range order would produce superdis-locations, consisting of two partial dislocations separated by an out-of-phase region. The mutual repulsion of the partial dislocations is balanced by the surface tension of the out-of-phase domain boundary joining the dislocations (Fig. 1). The calculation of the equilibrium spacing of the dislocations has yet to be made. The argument uses the Bragg and Williams theory of long-range order." The metal under consideration is the A-B, body-centered type, such as ß brass. The slip system is taken to be [Ill], (110). Since nearest-neighbor interactions are considered, only the atoms position in the two (110) planes adjoining the slip plane have to be labeled. Corner sites are called a and a' in the top and bottom (110) planes, respectively. Similarly ß and ß are the body-centered sites. Thus, a and ß and 0 and a sites are nearest neighbors. Assume that the bottom plane moves and the top plane is fixed during slip; the atoms in a and ß sites exchange sites but atoms in a and ß sites remain fixed. Fraction of A atoms in a sites, for example, is given by fa and fa. for the un-slipped and slipped condition, respectively. Similarly number of A atoms in the a sites is given by n, and n'a for the unslipped and slipped condition, respectively. As the dislocation moves into the ordered region the change in number of A-A bonds is given by

Jan 1, 1957

By Fred T. Greene

(San Francisco Meeting, September, 1915) MOST of. the recent discussion of the mineral land law published in the Transactions is in the abstract-an exception being Mr. Goodale's paper, The Apex Law in the Drumlummon Controversy,1 which illustrates in concrete instances many of the practical disadvantages of what Dr. Raymond has. called "The Law of the Apex." The present paper, it is hoped, may serve a similar purpose, emphasizing the necessity for a change in our mining laws, and bringing home to mining engineers some of the defects and dangers of our present code. There are many storm centers of "apex litigation" in the Rocky Mountains; and not the least of them is the Wardner camp, where such litigation has been almost continuous since 1892, and the end is not yet. In their decisions, the courts have accepted the claims of the litigants that the " Wardner vein" is a broad zone varying from 250 to 500 ft. in width at the surface. This is the simplest theory which could have been advanced, and probably decreased, rather than augmented, the number of contests; in fact, every one of the claim owners seemed to feel that the greatest advantage would accrue to him if this theory were adhered to. The dominant structural feature of the Wardner vein is a persistent fault, striking N. 40° W., clipping about 40° to the southwest and called the "Wardner foot wall." Fig. 1 is a composite of two adjacent cross-sections of the vein and is a fair representation of the relative size and shape of the orebodies and their relation to the "Wardner foot wall." The country rock is a comparatively thin-bedded sericitic quartzite which has an average strike of N. 80° W. and clips at high angles to the north and south.

Jan 5, 1915

By H. B. Goodrich

In considering historically oil development in Oklahoma, it must be recognized that basic evolutionary factors interlock and have an effect in common throughout the whole oil industry, regardless of locality or minor problems. Oklahoma, as the third in rank of oil-producing states (Texas being first and California second in production for 1929) has, like the rest, advanced to at least a partial recognition of the words, "Conservation," "Unitization," "Curtailment," "Prora-tion," and especially "Cooperation." Whether through altruism (of which there have been examples) or by exercise of good business common sense, Oklahoma operators realize that the oil business can run itself by cooperative action for the good of all. In this long-continued period of overproduction, Oklahoma has brought the advancing output down to limit of market requirements at least temporarily. Sources of Statistical Data For this paper, figures published by four recognized authorities were consulted. Between themselves these vary only a negligible per cent, in their totals. To be consistent, and on account of earlier availability the estimates published by the Oil and Gas Journal are mainly used herein, supplemented from other public and private sources. General Oil ProdCction in Oklahoma In 1927 Oklahoma's peak of all years was 276,022,024 barrels. In 1928 Oklahoma's total production was 247,500,851 barrels. In 1929 Oklahoma's total production was 252,229,474 barrels. The efforts of proration and curtailment programs on flush and semi-flush districts such as Greater Seminole, Oklahoma City, Logan County and others, with the natural decline of older pools, kept 1929 below 1927, but still the total was greater than in 1928. The total United States production for 1929 is herein taken as estiiated at 1,004,266,723 bbl.† Oklahoma produced 25.1 per cent. Of

Jan 1, 1930

By Olin G. Bell

The year 1934 in Southwest Texas was marked by aggressive development and exploratory work and resulted in the finding of five new fields and a new producing horizon in one of the older fields. This activity is the result of a reasonable market outlet for production, on both oil and gas, and the fact that drilling and operating costs are reasonable and that possibilities of finding new productive areas are rather high. A large part of the area is prospective and very little, if any, satisfactory surface geological work can be done. This, together with the possibility of finding new productive areas, stimulates wildcatting throughout the counties under discussion. Development work continued actively in all of the newer fields. Exploratory work was most intense in Duval, McMullen, Starr and Zapata counties. The activity in Duval and McMullen counties was the result of persistent efforts to find new trends of production similar to and perhaps associated with the Government Wells group of fields. The activity in Starr and Zapata counties was stimulated by the discovery of the Sam Fordyce field in Hidalgo County as well as the continued effort to find new productive trends southeastward from some of the older fields in northeastern Zapata County and western Jim Hogg Comity. Statistics on production are shown in Tables 1 and 2. New Fields Lopeno.—The Lopeno gas field in the southwestern part of Zapata County was opened in August, 1934, by R. B. Morrison No. 1 Ramirez. This is an anticlinal structure mapable in Claiborne beds and the producing horizon is the Queen City sand at 2100 ft. in the Upper Mt. Selman. At the close of the year only two gas wells had been completed but drilling operations were in progress on several other wells and a gas line was being laid to the field so that withdrawals from the area will begin early in 1935. Comilas.—The Comitas field was opened by Merle Gunby No. 1 Haynes in a sand at 800 ft. in an area southwest of the Escobas field. The discovery well had an initial production of only about 16 bbl. of oil

Jan 1, 1935

By C. P. Besse, G. W. Osborne

Drilling operations on the Gulf of Mexico continental shelf are following two general plans. The first plan placed all buildings. equipment, and materials on a large platform while the second copies Lake Maracaibo drilling methods by placing a minimum of equipment on the platform and using a floating drilling tender or drill barge anchored adjacent to the platform in an attempt to take maximum advantage of flotation in an effort to reduce costs. A complete power rig, mud pits, pipe racks, and small auxiliaries have been placed on the platform as shown in Figure 1, to assure proper handling of drilling operations under the most adverse weather. This has the economic advantages of eliminating the fabrication of a large structure, a material reduction of rigging up time on each structure. and elimination of delay time on equipment while quarters and equipment placed on the tender are being rigged up. These factors have certainly proved their economic value in drill barge operations in the Louisiana and Texas coastal area. Naturally the heart of such an operation is the anchorage. This anchorage, to permit taking advantage of maximum economies. must hold the ship in a relatively fixed position under the following weather conditions: (1) Winter northwesters (2) Southeasterly gales (3) Severe rain squalls In hurricane weather all operations must be suspended regardless of method of operation and the floating tender will, if possible, be moved to a protected location. However, in case of an emergency the floating tender should be prepared to swing with the wind and seas on a single anchor as there is considerable doubt that either ship or anchorage could withstand the severe strains imposed by fixed anchorage in hurricane weather. Northwesters are reported to have developed wind gust velocities as high as sixty miles per hour and steady winds of approximately forty-five miles per hour. Fortunately these winds do not travel a great distance over water before arriving at our location, and, while they can possibly develop seas approximately eight feet high, the waves are short, and if taken on the bow or stern of a ship 250 feet or more in length they should not present a difficult problem. On the other hand southeast gales having a long fetch and maximum steady wind velocities of approximately thirty miles per hour can possibly develop long swells approximately twelve feet in height. These should develop the most severe anchorage problem. To combat these waves any workable anchorage plan should permit maneuvering the ship in such a manner as to head the bow or the stern into the seas and still maintain contact with the structure. Rain squalls develop wind gust velocities as great as sixty miles per hour. However, they are local and the seas have not been a source of great trouble. To permit continuous operation the anchorage must be able to withstand these winds broadside to the ship as the wind direction often changes radically in a very sliort time. All of these weather conditions are dangerous to small craft, deck cargoes,

Jan 1, 1949

By C. P. Besse, G. W. Osborne

Drilling operations on the Gulf of Mexico continental shelf are following two general plans. The first plan placed all buildings. equipment, and materials on a large platform while the second copies Lake Maracaibo drilling methods by placing a minimum of equipment on the platform and using a floating drilling tender or drill barge anchored adjacent to the platform in an attempt to take maximum advantage of flotation in an effort to reduce costs. A complete power rig, mud pits, pipe racks, and small auxiliaries have been placed on the platform as shown in Figure 1, to assure proper handling of drilling operations under the most adverse weather. This has the economic advantages of eliminating the fabrication of a large structure, a material reduction of rigging up time on each structure. and elimination of delay time on equipment while quarters and equipment placed on the tender are being rigged up. These factors have certainly proved their economic value in drill barge operations in the Louisiana and Texas coastal area. Naturally the heart of such an operation is the anchorage. This anchorage, to permit taking advantage of maximum economies. must hold the ship in a relatively fixed position under the following weather conditions: (1) Winter northwesters (2) Southeasterly gales (3) Severe rain squalls In hurricane weather all operations must be suspended regardless of method of operation and the floating tender will, if possible, be moved to a protected location. However, in case of an emergency the floating tender should be prepared to swing with the wind and seas on a single anchor as there is considerable doubt that either ship or anchorage could withstand the severe strains imposed by fixed anchorage in hurricane weather. Northwesters are reported to have developed wind gust velocities as high as sixty miles per hour and steady winds of approximately forty-five miles per hour. Fortunately these winds do not travel a great distance over water before arriving at our location, and, while they can possibly develop seas approximately eight feet high, the waves are short, and if taken on the bow or stern of a ship 250 feet or more in length they should not present a difficult problem. On the other hand southeast gales having a long fetch and maximum steady wind velocities of approximately thirty miles per hour can possibly develop long swells approximately twelve feet in height. These should develop the most severe anchorage problem. To combat these waves any workable anchorage plan should permit maneuvering the ship in such a manner as to head the bow or the stern into the seas and still maintain contact with the structure. Rain squalls develop wind gust velocities as great as sixty miles per hour. However, they are local and the seas have not been a source of great trouble. To permit continuous operation the anchorage must be able to withstand these winds broadside to the ship as the wind direction often changes radically in a very sliort time. All of these weather conditions are dangerous to small craft, deck cargoes,

Jan 1, 1949

By Horace Winchell

IT IS OFTEN interesting to look backward and review the world's progress in any line of human endeavor. Our pride is flattered by our achieve-ments and our imagination stimulated by the compari-son between our present productivity and prosperity and those of the relatively unenlightened days of our recent ancestors. We love to reflect on the progress of the last quarter of a century in the art of metallurgy, in. the production and consumption of the various metals and minerals which constitute the basis of our industrial and commercial supremacy. We dwell complacently on the figures which prove that we are the world's leader in nearly all departments of mining and that our production of necessary minerals over-shadows that of other countries. We recall the days when it was considered the proper thing, if not indeed indispensable, to go abroad for the rounding out of a mining engineer's education. We had no mining schools equal to those of Germany. Our schools of technology were elementary and their equipment limited. RISE OF AMERICAN MINING SCHOOLS Now we point with true American pride to institutions which, are unsurpassed in all the world in their standard of efficiency. We know full well that the American engineer is in demand in many foreign parts and when we read recent scientific treatises published abroad we are amazed to find them unfamiliar with many of the more advanced ideas which have here already come to be an everyday part of our professional knowledge and equipment. Blessed with a country of unrivalled natural resources, dwelling in a latitude whose climate is most conducive to enterprise, peopled with races of inventive and organizing genius with equality of individual opportunity, our industries have grown and expanded until our output has reached staggering proportions and the draft upon our mineral reserves is appalling. Coupled with this development has arisen a demand for engineers which has brought into our schools of technical science larger and larger numbers of young men whose imagination has been stimulated by the success of their predecessors who happened to be contemporary elements in the recent industrial expansion and prosperity.

Jan 1, 1923

By E. H. Wells, A. Andreas

The oil and gas industry of New Mexico recorded notable progress ill 1935. More wells were brought in than in any previous year, and important new discoveries were made. The total number of completions was 340, of which 260 were oil wells, 8 were gas wells and 72 were dry holes. The total oil production was 20,228,947 bbl., an appreciable increase over the 1934 production of 16,636,804 barrels. Many of the wells completed in southeastern New Mexico were acidized. This treatment proved highly effective in increasing the capacity of the wells, the resulting potentials usually being two to ten times as large as before acid treatment. In the Lea County fields in which proration was entirely on an acreage basis, the tendency of many of the operators was to complete their wells according to best conservation practice rather than to obtain the largest possible potential. Much remedial work was done in the Hobbs, Cooper, Jal and Eunice fields, and with excellent results. At many of the wells high gas-oil ratios were greatly reduced and encroaching waters shut off by setting packers. Several companies carried on pretentious geophysical campaigns in the southeastern part of the state. The location of the Amerada discovery well in the Monument field was based on geophysical surveys. The New Mexico Oil Conservation Commission, established by the 1935 Legislature and consisting of the Governor, the Commissioner of Public Lands and the State Geologist, began to function in May. Production in the state thereafter was based on orders issued by the Commission. Proration in the Hobbs field, which had been provided for since July, 1930, by successive proration agreements signed by all operators in the field and approved by the State Geologist, was continued by the Commission by giving approval to the current proration agreement,. A plan of proration for the other Lea County fields that had been in offect since early ill 1934 was adopted. 111 September, 1935, the Commission approved a. proration agreement for the Artesia-Jackson-Maljarnar area in Eddy and Lea counties that had been agreed upon by

Jan 1, 1936

By R. V. Ramani, R. Stefanko, P. C. Thakur

The effects of diesel exhaust on mine ventilation systems are discussed. Mathematical models for emission of gaseous pollutants from diesel engines and their dispersion into mine air have been developed. Situations likely to prevail in mines were originally modeled using partial differential equations, but only simplified solutions are presented here. Validity of these models has been established by field observation of the growth of carbon monoxide concentrations in mine air environment. Consequently, these models can be used for air requirement calculations for diesel engines in underground mines.

Jan 1, 1977

By O. E. Michaelis

The metal used at the Befors Works in gun-munufacture is unforged open-hearth steel, cast without blow-holes. It has from time to time been asserted that it is impossible to pro

Jan 1, 1888

By C. Ernest Birchenall

As a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.1 In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in. the preceding paper.2 A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken .3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity data given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below.

Jan 1, 1947

By P. D. Proctor, M. P. Nackowski

Quantification in recording geologic phenomena and application of well-known geologic principles to engineering works continued at an increasing rate during the year. Highway departments, water resources agencies, private firms and governmental agencies involved in tunnel excavations, dam site locations and construction, consultants and government experts in subsurface liquid-waste disposal, designers of underground storage facilities and city and regional planners all confirmed greater use of applied geology in their planning and implementation of plans. Applications of quantified geologic data to highway locations, slope control of cuts, raw material sources, water sources and water run- off showed a striking increase in number. Environmental geology and geologic hazards became part of the jargon of the geologic profession, and the American public began to realize more fully the significance of where they live, and on what and near what geologic phenomena which might effect their well-being. Tunnel work for water projects of almost dream-like magnitude kept geologic engineers busily engaged in predicting and testing local geologic conditions for construction projects. Disposal of industrial and radioactive liquid wastes continued as problems, but use of stratigraphic data, fluid flow rates and direction of flow helped solve some critical waste disposal problems. Unusual applications of seismic networks, remote sensing methods and X-ray techniques in geological engineering applications added other tools to this increasingly important profession.

Jan 2, 1968

By V. Carlson, J. A. Rowe, E. O. Bennett

This report concerns the microbial flora found throughout the surface facilities of six water-injection systems in Texas and Oklahoma. Each system is described in detail and water quality data are presented when available. Pseudomonads and sulfate-reducers (Desulfovibrio) were the predominate organisms found in the systems. The genera Sphaerotilus, Bacillus, Achromobacter, Minococcus, Clostridium, Flavobacteriurn, and Sarcina were also isolated in significant numbers. Molds, iron bacteria, sulfur bacteria and soil bacteria were found less frequently in the systems. It is concluded that a complex microbiological flora exists in oilfield water-injection systems. A tendency for waters to deteriorate in passage through solid bed filters is also noted. INTRODUCTION The injection of water into a subsurface formation is often accompanied by numerous problems, the origin and nature of which are only partially understood. During the past few years, investigators have indicated that bacteria are involved in some of these problems even though very little specific information is available concerning this matter. It is surprising that investigators working on microbiological problems in water injection have never made a complete study of the flora of these systems. The logical course to pursue is that of identifying the microbial flora and then examining each organism individually and in combination with others to determine if they produce a particular problem. The objective of the present investigation is to identify the microbial flora in water-injection systems. In addition. the quality of the water in most of the systems was determined and some observations made on the extent to which passage through surface-handling facilities affects water quality. The information derived from this study can serve as a foundation for additional basic investigations. EXPERIMENTAL PROCEDURE The microbial flora of six water-injection systems were studied at 50 sampling points. These systems are experiencing problems which may be attributable to micro-organisms, and two were being treated with antimicrobial agents at the time of this study. The samples were obtained by inoculating 1.0 ml of the water onto the different media at the sampling point. The media used for primary isolation included nutrient agar, Strokes agar, M-10-E medium and semi-solid thioglycollate medium. The cultures were returned to the laboratory, incubated at 30°C until growth occured; then, pure cultures were obtained from individual colonies. The pure cultures were identified according to standardbacteriologica1 procedures. Those organisms not fitting identification criteria exactly, even though exhibiting close similarities to known species, are listed as unidentified organisms. Membrane filters were used to make water-quality tests at intervals before and after collection of the microbiological samples. The filter discs were 47 mm in diameter with a 0.45-micron particle-size retention, and the tests were done under closed conditions at 20) psi. Membrane flow rates are plotted as increasing filtrate volumes, and the total solids contents arcs given when available. An effort was made to sample at each place in a system where a change in environment occurred. In this manner, the effect of passage through filters, tanks, hay sections, etc., on the microbial flora and water quality could be observed. RESULTS SYSTEM A This waterflood system (Fig. 1) is about four years old and daily pumps approx&ately 110,000 bbl of oil-free sour water from a 3,700-ft deep reef. The