Search Documents

By Norman D. Fitzgerald

The growth of domestic requirements for motor fuel has been phenomenal, rising year after year in a fashion almost unique among commodities, resisting depressions and forging rapidly ahead in times of prosperity. Consumption advanced from 226 millions of barrels in 1925 to 522 millions of barrels in 1938; or 130 per cent. The economic influences generating and sustaining this demand are of vital concern to the petroleum industry. The general factors affecting utilization of motor fuel are well known but it is the purpose of this paper to employ the recently developed technique of economic dynamics to describe them mathematically. Such problems in economic analysis are complicated by the freedom of all the variables to fluctuate, their mutual interdependence, changing incidence upon one another, and the nonquantitative character of some of them. Economic quantities and relationships, unlike those of the physical world, are continuously changing and this dynamic characteristic is both a distinguishing and confusing feature in economic research. The complexities of the problems require application of the analytical devices of mathematical statistics to uncover the probable relationships between factors. The procedure employed is to formulate a logical relationship linking the dependent to the independent variables, and then simultaneously, rather than sequentially, determine their separate effects by multiple correlation. This transformation of common knowledge to quantitative terms makes it possible to measure the probable effects of changing conditions upon requirements, assisting in the sound interpretation of economic policies. The utility of the results of such dynamic analysis is in sharp contrast to the sterility of the trends and other simple empiricisms of descriptive statistics. It is not intended in this study to throw light on the reasons why any motor fuel at all is consumed; but to discover relationships explaining why more was consumed at one time than at another. Specifically the problem is confined to the measurement of the influences of statistically

Jan 1, 1940

By Jed H. Mosgrove

Ventilation is the method of producing, conducting, and distributing a constant current of fresh air through mine workings and returning the impure air to the outside atmosphere. Without ventilation no operations are possible in an underground mine. Therefore it is the most important single phase of mining, one on which everything else depends. A good ventilation system, therefore, must be correctly designed, properly conducted as the workings advance, and continually checked to make sure it is functioning correctly. Good air is essential for men to comfortably and safely perform their work. It is also essential to dilute, render harmless, and sweep the mine of any explosive fumes and the gases that are released in varying degrees by all coal seams and the rock strata in which they are contained. GENERAL The body of air that is being moved through the mine, known as the ventilating current, must have a definite way to enter and leave the mine. In other words, there must be a definite intake and return. The main consideration is to get the proper amount of good quality air to the working faces where it is needed. Inasmuch as the mine is divided into sections with interconnecting corridors, known as entries, it is necessary that there be a proper means of conducting the air to the proper points. As a simple explanation of a mine, consider a long tube and think of it in terms of a mine entry ill which the air must pass. The tube must have at least two openings before air can travel through it and this is the same for coal mine entries. The problem in ventilation is to find some means that will cause the air in the tube to flow from one end to the other. The only possible way to do this is to cause greater pressure at one end of the tube than at the other. Air at the end with the greatest pressure would then, of course, flow to the en which has the least pressure. Mine

Jan 1, 1973

By J. R. Cooper, A. Bruynesteyn

The final results of the operation of the Cananea test dumps are discussed. Scale-up factors between shake-flask tests, column tests and the large test dumps are established for the Cananea ore. The formation of clay layers, which formed inside the dumps and markedly affected extraction, as well as secondary enrichment, are discussed.

Jan 1, 1974

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

By L. D. Jaffe, J. H. Hollomon

THE effect of tempering temperature and time upon the properties of quenched steel is clearly a subject of great practical importance, as well as of considerable theoretical interest. It would be very desirable to be able to predict the properties of a quenched steel when given any selected tempering cycle, with a minimum of experimental work upon that heat or even type of steel. Two problems are involved: one consists of relating the structure obtained to the physical properties, and will not be discussed here; the other, with which this paper deals, involves the relations of time, temperature and composition with the structure obtained on tempering. Indentation hardness is perhaps the most convenient quantitative measure of the tempered structure, or of what might be called the "degree of tempering." Undoubtedly, it is not an exact measure, and in some cases (as when temper-brittleness occurs) pieces of the same quenched and tempered steel may have widely differing properties at the same hardness. However, hardness has the advantage of being simple to determine and is certainly the most widely used indication of the degree of tempering. Moreover, for fully quenched steels that are not temper-brittle and do not contain retained austenite when quenched, it appears that, in general, if the hardness of the steel is the same, the tensile and impact properties will also be identical, whether a high or a low tempering temperature is used. The tempering charts available in the metallurgical literature usually give the hardness as a function of tempering temperature for only one tempering time. However, in practice, tempering times frequently vary, and a method of converting tempering curves for one time to tempering curves for some other time would be very valuable. It is also advantageous, in determining the tempering treatment necessary for a given part, not to have to temper samples at several temperatures for the time used for the commercial tempering operation. A more satisfactory procedure would be to employ times of the order of 10 to 30 min., rather than 5 or 10 hr., and if possible to use only one temperature. Furthermore, it is frequently desirable, for reasons such as temper-brittleness,* to obtain a given hardness with short times at relatively high temperatures, and it would be convenient to be able to compute without tests the time required to produce this hardness. Remarkably few quantitative studies of the hardness of quenched steel tempered over wide ranges of temperature and time

Jan 1, 1945

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.' The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.' Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low' used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966

By Lawrence Burkhart, S. B. Joo

Axially unsymmetric ordered circulation patterns on the surface of a hemispherical constant volume drop with forced Internal motion were considered as a manifestation of hydrodynamic instability, which was affected by internal flow as well as by the properties of the interface A simplified mathematical model was analyzed In order to study the mechanism of onset of interfacial circulation from a non-circulatory basic state. Values of the critical Reynolds numbers were obtained when the basic state became a fully developed rotational flow and the values changed for different interfacial properties. The work describes a heretofore unreported surface flow pattern on drop surfaces From a practical point of new, any motion in the interface of a droplet can have a significant effect of mass transfer rates in solvent extraction processes Although surface motion in droplets actual processing equipment is very complex, continued study of the fundamental nature of such phenomena should ultimately lead to more effective equipment design procedures.

Jan 1, 1981

By G. W. Josephson

SINCE the earliest years of recorded history the durability and protective qualities of asphalt and tar have been known and utilized. The mummies of early Egyptian kings were coated with asphaltic materials, and asphalt mastics were common in Babylon. However, according to various authorities, it was not until 1780 that the first forerunner of present-day composition roofing was discovered,1 and the large-scale expansion of the industry has taken place since 1900. HISTORICAL BACKGROUND Development was stimulated by the growing popularity of manufactured gas. The by-product tars from these operations accumulated in large waste piles that had no commercial value and were a source of annoyance and expense to the gas companies. These tars were offered at very attractive terms to anyone who would take them away, and the infant "composition" roofing industry benefited accordingly. At first the process consisted simply of dipping sheets of burlap or other fabric in a tank of molten tar or asphalt. The long strip of roofing was rolled up for convenient handling, and the early experimenters soon found that it was necessary to dust the surface of their new "roll roofing" with some kind of material that would prevent the tarred surfaces from sticking together. Any finely divided, low priced local material like sand or fine gravel served this purpose and from its application the roofing-granule industry grew. As time went on other characteristics of a properly applied mineral surfacing were recognized. As with wooden shingles, tar and asphalt can be ignited by flying embers from near-by fires. It was found that by increasing the largest particle size to the maximum that could be successfully embedded, and by properly controlling the amount of smaller fractions retained in the grade so as to cover the asphalt completely a Nigh degree of resistance to fire was attained. Needless to say, in this early period asphaltic roofing needed such selling points to gain acceptance in a field dominated by wood, slate, and tile. When asphalt is protected from the sun's rays it is extremely durable, but when exposed to sunlight its surface is comparatively rapidly decomposed. Completely covering asphalt roofing with mineral surfacing protects the asphalt and adds materially to the life of the roof-conservatively, 500 per cent. Slate Granules In the production of split slate shingles a large quantity of waste slate is accumulated, as 60 to go per cent of the rock quarried is discarded. This waste was a continuing burden on the industry. Some was marketed as ground slate flour for filler in paint and linoleum, and there is a record that as early as 1906 two carloads of coarse screenings from slate flour were marketed as granules for surfacing roofing. This new field appeared to the slate pro-

Jan 1, 1944

By J. M. Duke, A. J. Naldrett

Significant resources grading less than about 1% nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greenstone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifring. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1983

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By Clarence E. Killebrew

The key to the successful use of any tool, more than anything else, depends upon proper application assignment. To achieve this, the individual having such machine responsibility must maintain fresh knowledge of technical improvements that broaden machine uses. 8.3-1. Tractor Shovel. This type machine is available in a wide range of sizes mounted either on crawler tracks or rubber-tired wheels, with both two-wheel and four-wheel drive. The original concept in both crawler and rubber mounting was that of an attachment to be added to a tractor already in existence. This served as an important expedient for the introduction of the tool, but the basic tractor proved to be inadequately designed for the additional loads. In spite of these structural inadequencies, customer acceptance generated sufficient revenue that further development could be financed for product improvement. The evolution of the product is continuing in many ways-including engines, drive line components, tires, hydraulic pumps, hydraulic valves, structural steel, etc. With each improvement, the operating capability of the machine is extended. This is resulting in the rubber-tired, four-wheel-drive concept making an invasion of the job applications that were formerly considered suitable only for crawler-track mounted machines. Both rubber- and crawler-mounted tractor shovels have invaded the market of small excavator shovels. Larger tractor shovels are challenging the larger size excavators. It is important that each job application be carefully considered so that the proper machine is put in operation. The performance varies widely in operating cost, production efficiency, and job flexibility. Factors to be considered in equipment selection are: 1. Nature of material to be moved 3. Distance material must be moved 2. Surface over which material must be moved 4. Quantity to be moved 5. Secondary or alternate use capability

Jan 1, 1968

By F. G. McCutcheon

UNTIL about 1930, the universal practice of horizontal-retort zinc smelters in the United States, as far as the writers are aware, was to operate the retort furnaces on a 24-hr cycle; that is, the retorts were charged in the early morning of one day, and in the early morning of the following day the residues were cleaned out, the retorts recharged, and a new cycle started. During the business depression of the early thirties, zinc production fell off to the extent that zinc smelters had idle retort capacity. Rather than continue to run some of the retort furnaces on a 24-hr cycle and shut down the remainder, a few companies decided to try out a longer cycle. Although the output of zinc per retort per day is lower, the longer cycle permits a larger charge per retort and improved zinc recovery. Advantages of the longer cycle were soon evident, and the practice spread rapidly. Various lengths of cycle were used, typical examples being 28-hr, 32-hr, 36-hr, and 48-hr. The 48-hr cycle fits in best with the standard routine of smelter practice that was built up on the basis of the 24-hr cycle; that is, the retort furnace "maneuver" always comes at the same time of day, and can be performed in the cool hours of the early morning. Under some conditions, particularly in some of the older plants, where the retorts are smaller than in newer plants, a 48-hr cycle is longer than necessary, and some intermediate length of cycle may theoretically be most economical. Use of an intermediate cycle, however, means that the maneuver comes at different times on consecutive days, and that sometimes it comes during the hottest part of the day. The work on the retort furnaces is extremely hot and arduous at best, and it is much worse, of course, if it is done during the heat of a summer day. When labor was plentiful and tractable, many plants were able to operate on cycles of intermediate length, but the workmen did not like the working hours. Under present labor conditions, it is hardly practicable to operate with a cycle of intermediate length, so the choice has narrowed down to the alternatives of 24-hr or 48-hr cycles. In any discussion of economics, too comprehensive generalization is not warranted, because local conditions affecting economics vary greatly. The best economic practice at one plant at any given time may be uneconomical at another plant, or even at the same plant at another time. To determine the length of cycle that is the better practice at a given plant at a given time requires a weighing of the advantages and disadvantages of each cycle, taking into consideration all the local conditions. Some of the factors that must be considered in making the comparison are discussed briefly in the following paragraphs.

Jan 1, 1947

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By R. S. McFarland

OKLAHOMA, in 1924, recorded the largest single increase of any state; the total oil production for the year being 176,206,397 bbl. (Oil & Gas Jnl.), which gives an increase over 1923 of about 9 per cent. Oklahoma ranked second in total amount, California being first, and produced almost 25 per cent. of the total production of the United States. This gain in production is accounted for entirely by the rapid development, deeper drilling, and efficient management of productive areas known at the beginning of the year, for, due to the small number of wells drilled, few new pools were discovered and developed up to any important stage during the year. Three major pools, Burbank, Tonkawa and Cromwell, furnished 37 per cent. of the total production. Burbank led by a wide margin, having the largest production of any single pool; there was a steady increase in production until September. The close. development of the pools in Okfuskee, Seminole, and Hughes Counties, together with the new deep-sand production at Tonkawa and increased drilling operations in Osage County, accounted for the big increase shown during the year. In January, 1924, the shutdown movement and curtailment of production in Hewitt and Tonkawa, which had been effective during the year of 1923, were stopped. The shutdown movement and curtailment of operations in 1923 does not give a fair comparison with 1924, as undoubtedly a great deal more oil would have been produced in 1923 had it not been for these measures. The sensational developments during the year, which were certainly beyond the prediction of the oil industry, were the Cromwell field, which started the year with 10,478 bbl. for January and increased rapidly to 1,267,032 bbl. for. December, and the discovery of the Wilcox productions below 4000 ft. in the Tonkawa field in May, which by the end of the year had produced 11,650,000 bbl. In this connection, it can be safely said that 1924 was a banner year for the Wilcox sand series; it has been estimated that between 40,000,000 and 50,000,000 bbl. of the production for the year came from this sand. Although numerous Wilcox pools were opened throughout the state, the big Wilcox production came from. the Tonkawa and Stroud pools. Oklahoma's deepest well, the Kingwood Oil Co. No. 1 Barnett in the northwest corner of the northeast quarter of the southeast quarter of Sec. 7 T. 7 N. R. 10 E., Hughes County, was abandoned in January, at 5281 ft. with numerous good shows recorded, which have stimulated-further drilling in the locality.

Jan 3, 1925

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By J. Philip Neal, Carroll P. Rogers

Feldspars, the most abundant minerals of the igneous rocks, occur in numerous forms and mixtures. The feldspars of commercial significance are found in widely distributed pegmatites as large crystals usually free of iron- bearing impurities and thus suitable for hand-cobbing, and also in larger bodies where the ore contains various types of feldspar inter- mingled with quartz and relatively free of iron- bearing impurities, or at least readily unlocked from impurities present at relatively coarse mesh. The latter type of ore includes some pegmatites, and the ''alaskite" bodies so common in the Spruce Pine district of North Carolina. On the west coast of the U.S. and in Oklahoma there is-r has been--commercial recovery of natural feldspathic sand as a source of alumina in glass and ceramics. "Aplite" in commercial terminology is a light-colored igneous rock with a granitic composition and a fine sugary texture, often banded with readily removable iron impurities. Two areas in Virginia produce aplite for the glass industry: one located in the vicinity of Piney River, Amherst County, and the other near Montpelier in Hanover County. According to Deer et al. (1966) the word feldspar derives from the Swedish feldt or falt (field) and "spath:" chunks of rock appearing in tilled ground overlying granite. Castle and Gillson (1960) indicate a Germanic origin, citing "spat," which is said to refer to any transparent or translucent material which is readily cleavable. The term "spar" has in the past been applied to minerals other than feld- spar, such as barite, calcite, and fluorite. It is correct to call the latter "fluorspar." There is a true barium feldspar, but it is rare and of no present economic importance. What is recognized as feldspar or "spar" by present producers and consumers consists of three silicate minerals which, if pure, would have the formu- las KAISi,O, (microcline or orthoclase), NaAlSi,O, (albite), and CaAl,Si,O, (anorthite). These are almost never found in pure form in nature, but occur together in great abundance in a three-component system. A considerable number of different combined ratios of these three exists, with the exception that isomorphism between potassium spar and calcium spar is very limited. User specifications for feldspar products are largely built around the prevalent naturally occurring ratios. Pas- sages following will refer to "K-spar," "Na- spar," or "Ca-spar." Nomenclature and Descriptive Terms Relating to both the mineralogy and the economics of feldspar are certain terms whose coverage it is useful to specify. Commercially, aplite is a feldspathic rock mined and beneficiated in two locations in Virginia, in which both titanium and feldspar minerals are present-the latter now being the major, if not the only, economic product. Technically, the term aplite when applied to this rock is of questionable accuracy. But, in light of accepted commercial usage, the term will be here used to designate it. Regarding the Virginia rock, Ross (1941) is cited.

Jan 1, 1975

By Howard W. Jacky

At Weed Heights, Nev., precipitation plays a major role in the plant operation. Almost two-thirds of the present copper production is leach-precipitation plant copper. The entire plant complex processes about 135,000 tons of low grade copper ore per week. Of this tonnage, 49,000 tons of about 0.78% sulfide ore are treated in the concentrator. This is handled in the conventional manner of crushing, grinding, and concentration of the copper sulfide by flotation.

Jan 6, 1967

By H. C. Goodrich

THE earliest record of copper production from the state of Utah comes from "The Resources of Utah," by. Mr. Fabian, in 1872, wherein it is stated that the. Mammoth mine of East Tintic was located in 1870 and that the ores yielded a large percentage of copper, silver and gold. It is also stated that shipments had been made to Swansea, England, which assayed between $200 and $300 per ton. The Mammoth-Copperopolis mine was located in, 1870 and sold the year following to an English syndicate. Some copper was shipped to. England and in 1873 there was constructed a 15-stamp mill and two copper smelting furnaces; these were operated a few months and before the end of the year were closed down and the property sold for debt. . This property -vas reorganized in 1879 and is at the present day a producer, though its principal product now is lead and silver. While a certain amount of copper has always been coming from the various lead-silver camps of Utah, the real history of copper in Utah should start with the discovery of the mines in Bingham Canyon, located about 25 miles to the southwest from Salt Lake City.

Jan 1, 1925

By A. Schild

The effect of heating a producing well on the rate of oil recovery has been analyzed in the simple case of a well producing oil by a radial drive and in the steady state. Differences of production rates with and without borehole heating have been calculated and plotted; these measure some of the benefits of the thermal recovery process. A striking feature is that the production increase tends rapidly to a constant value for large production rates. Some concrete examples, including a rough comparison with field data. are discussed. Heating requirements have been calculated and plotted on the assumption that the heaters used are 100 per cent efficient. Heating has been thought of as applying only to low volume wells producing heavy oils. However, the calculations suggest that the thermal process considered might be profitable even for some wells producing large quantities of light oil, especially in unconsolidated formations where fracturing is not possible. In the case of wells producing other fluids with the oil or of wells producing partly or wholly by gravity drainage, the theory developed does not apply in detail. It can be expected, however, that any general qualitative be-havior will remain valid. Under normal temperature conditions, high viscosity emulsions sometimes form around the wellbore, lowering the permeability in the vicinity of the well and impeding the production of oil. Borehole heating often prevents such emulsification. This important effect is not easily amenable to mathematical analysis and has not been included in the theory presented here. It should therefore be kept in mind that the benefits due to borehole heating may in fact exceed the values given by the following calculations. INTRODUCTION The recovery of viscous, low gravity oils can often be stimulated by applying heat to the production zone. The higher temperature lowers the viscosity of the oil, increasing its mobility, and therefore its rate of production. One thermal method of recovery 1,2,3,4. consists in operating a heater inside a producing well and, at the same time, producing oil from the well. In this paper a simple theoretical model is analyzed to study the effect of such heating on the recovery of oil. The reservoir mechanics of the process is the only aspect of the problem which is considered here. The details of the heating system are ignored, and it is simply assumed that the heater raises the temperature in the immediate vicinity of the producing well to a pre-assigned temperature T w. Although heating requirements are calculated, these refer only to the heat supplied to the formation and to the oil being produced; they do not include heat losses due to the inefficiency of the heater. A short outline of the theory follows: The heat supplied to the producing well flows out into the formation by means of thermal conduction. At the same time, the flow of oil carries heat by convection from the formation towards the producing well. After sufficient time has elapsed, a steady-state is reached where the temperature, the velocity of the oil, etc., no longer vary with time but are functions of position only. In the steady state the temperature decays like an inverse power from the high value Tw at the wellbore to the original reservoir temperature T. at some distance away from the well. The effect of the high temperature and low oil viscosity near the producing well is the same as if the oil were produced at reservoir temperature To but through a producing well of a larger radius. From this point of view, the energy and money being expended to provide heat

Jan 1, 1958

By William G. Schultz

Sylvite of Canada, a division of Hudson Bay Mining and Smelting Co., operates a new 8500-tpd potash mine ten miles northeast of Rocanville, Sask. This mine, employing less than 60 men in its underground maintenance, engineering, and production operations probably ranks as one of the most highly mechanized and automated mining operations in the world. Access to the flat lying potash bed is through two 16-ft-diam concrete and steel lined shafts 3300 ft deep. The backbone of the operation is two 258-ton, 1500-hp continuous mining machines capable of mining in excess of 700 tph per machine while employing extensible conveyors for haulage. This production capability is complemented by a completely automated haulage, storage, and hoisting system. Of the other unique features of this operation, the principal ones are that the mine was designed and developed by the people that are currently operating it and from the time the shafts were commissioned, the mine was completely developed, equipped, and brought to full production in less than six months.

Jan 1, 1974