Search Documents

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid cobalt and a number of dilute cobalt alloys Was measured in the temperature range 1550" to 1700°C at nitrogen pressures to 1 atm. At 1600°C and 1 atm nitrogen pressure, the solubility in pure cobalt is 0.0047 wt pct [3.8 cu cm (stp) per 100 g Co]. The standard free- energy change for the solution reaction 1/2 N,(g) = gout pct in Co) is iF - 10,000 + 5.24 T cal per g atom N. The alloying elements Cv, Cu, Mo, Nb, Tu, W, and V increase the nitrogen solubility, while Al, Fe, Ni, and Si decrease the nitrogen solubility. THE solubility of nitrogen in cobalt was studied previously by Sieverts, Busch and Dodd,2 and Schenck, Frohberg, and Graf.3 Sieverts investigated the solution below the melting point of cobalt, and Busch and Dodd worked with the liquid metal; however, neither study found any solubility for nitrogen in cobalt. Schenck et al, reported a solubility of 0.005 wt pct N in cobalt at 1600°C. Seagle et al. 4 reported residual nitrogen in cobalt after electron-beam melting, although no reasons were ventured for the presence of this interstitial impurity. This investigation was undertaken to clarify these inconsistencies, and to provide additional data on atomic interactions in dilute metallic solution. EXPERIMENTAL PROCEDURE This study was well-suited to the Sieverts' method, which has not changed significantly since its introduction by Sieverts. 5 The apparatus was of the same design as that described by Humbert and Elliott, 6 with a reaction bulb similar to that reported by Weinstein and Elliott. 7 The buret was not water-jacketed, but the measured gas volumes were corrected for small changes in room temperature. The melt temperature was measured by a disappear ing-filament optical pyrometer sighted through a prism onto the melt surface. Temperature calibration was made based on a measurement of the melting point of pure cobalt taken as 1495°C. The difference between the reciprocal of the observed and the true temperatures was assumed to be a constant, neglecting the changes in emissivity with small additions of alloying elements. The total error in gas-volume measurement caused by accuracy limitations in reading the mercury level in the buret, variation in ambient temperature, and variation in melt temperature was about 0.5 cu cm. This represents approximately 10 pct of the total solubility, and is a larger relative error than in previous studies6-' because of the small nitrogen solubilities encountered in the present investigation. The source and purity of the materials used are listed in Table IA. Recrystallized alumina crucibles were used throughout the investigation. Examination of the crucibles after solidification of the melts showed no reaction or penetration. Alloying of the cobalt melt was accomplished with the dropping technique described by Humbert. 6 The investigation was started using cobalt from African Metals Corp. in shot form, but this material was not of sufficient purity and did not yield consistent solubility results. Sherritt Gordon Mines Ltd. cobalt was then used throughout the investigation. In experiments involving alloying elements which could react with oxygen dissolved in the melt, the cobalt was further refined by annealing at 1400°C in a dry-hydrogen atmosphere. This treatment, described by Woolley and Pehlke, 8 markedly reduced the oxygen content. The oxygen and nitrogen analyses of the cobalt used in this study are presented in Table IB. RESULTS Hot Volume. The hot volume was measured prior to each run and was 50 to 55 cu cm (stp) at 1600°C. It increased linearly with increasing pressure and decreasing melt temperature. Pure Cobalt. Measurements of the solubility of nitrogen in pure cobalt and the temperature coefficient of solubility are summarized in Table 11. At 1600°C and 1 atm nitrogen pressure, the solubility was found

Jan 1, 1967

By W. R. Shimer

In his valuable report on Finishing Temperatures and Properties of Rails,l Dr. G. X. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying out the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high percentages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility than rails of identically the same composition and section which were rolled direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 1, 1915

By Paul Gordon

The distribution coefficient, k, of interest in zone refining is generally defined as the ratio of the solid to the liquid solubilities of one element in another at the normal melting point of the solvent. In practice, distribution coefficients are frequently calculated from solubilities at temperatures well below the melting point of the solvent, e.g., at a eutectic temperature. This is done because of the general lack of accurate data on the liquidus and solidus curves in most phase diagrams. The practice is equivalent to assuming that the liquidus and solidus curves are straight lines in the temperature range between the melting point of the solvent and the temperature at which data for the solubilities are known. It is recognized that the k values so derived may be in serious error; we have found evidence in recent zone-refining operations that a case in point is silicon in aluminum. The phase diagram found in the literature for silicon in aluminum indicates a eutectic on the aluminum-rich side at 12.5 at. pct Si and at 577°C,1 and a solid solubility of silicon in aluminum at this temperature of 1.59 pct.2 It also shows the liquidus and solidus as nearly straight lines from 577°C to the melting point of aluminum (660°C)1,2 The k value obtained from this data is 0.13. This is almost exactly the same as the k value (about 0.14)' obtained in a similar way for copper in aluminum. Yet we have found by mass-spectrograph analyses* of three bars of zone-refined aluminum that copper is efficiently removed from aluminum by zone refining but silicon is not. Two of the three bars of aluminum were zone-refined in our laboratories, the other in the laboratories of AIAG Metals, Inc. The former two bars, designated bars PG2 and PG3, were 30 in. long by 1 in. in diameter during refining; each was processed in a high-purity graphite boat* and kept under refining stage of the process consisted of thirty unidirectional zone traverses at rates of about 1 to 2 in. per hr, with a zone length of 1 to 2 in. At approximately the middle of the refining period a 6-in. piece of the impurity-laden finishing end of the bar* was cut off and replaced with new start- ing material. Following refining, the purest 20-in. section of the bar (obtained by discarding approximately 2 in. of the starting end and 8 in. of the finishing end of the bar) was leveled and then analyzed. The AIAG bar was 16 in. long and about 1.2 in. in diameter; it was purified by eight passes of a 2-in. zone at a rate of 1.6 in. per hr, the bar being contained in a sintered alumina boat lined with loose alumina powder of the highest purity. Data for the silicon and copper contents of the three refined bars are given in Table I. Derived data for the efficiencies of the zone-refining operations are listed in Table 11. It is clear from these two tables that the copper is removed much more efficiently—by a factor of 10 to 50 times—from aluminum during zone refining than is silicon. For example, in bar PG3 the thirty zone passes reduced the copper content from 10 to 0.02 ppm, i.e., by 500 times, whereas the same treatment lowered the silicon content by only a factor of about 16. It seem virtually certain, therefore, that the distribution co efficient, k, for silicon in aluminum is well above that for copper and is very likely not much below unity. This also implies that the solidus line on the aluminum-rich side of the A1-Si phase diagram is very probably appreciably curved near the aluminum melting point since the phase-diagram data indicate such curvature is unlikely in the liquidus.

Jan 1, 1965

By Douglas Bunting

THE first presentation of this paper was before the Pennsylvania Anthracite Section of the Institute in May, 1914, after which a committee was selected to verify and add to the data contained in the original paper. The author is indebted to G. W. Engel, H. W. Montz, R. V. Norris, and H. H. Otto, of this committee, for additional information. I also wish to acknowledge the courtesies extended me by a number of the mining companies for information relative to accidents, systems of proving, and mining practice. The paper should bring forth additional criticism and recommendations, which will be of value in establishing future practice relative to this subject. Throughout the northern anthracite field of Pennsylvania glacial and alluvial deposits of sand, gravel, and clay exist in varying quantities. The extent and character of these deposits are described by N. H. Darton in Bulletin 45 of the U. S. Bureau of Mines, entitled, Sand Available for Filling Mine Workings in the Northern Anthracite Basin. It is estimated that the northern field contains 10,000,000,000 tons of these deposits, or a sufficient quantity to cover the 176 square miles of coal area to a depth of about 25 ft. These deposits of sand, etc., overlying the coal measures attain a maximum depth of more than 300 ft., and are usually saturated to such an extent as to render them semi-fluid. It is .this condition of fluidity that limits the mining of coal seams cropping in or in close proximity to these deposits, and it is in the interest of safer and more efficient mining methods under these conditions that the study of this -subject is here presented. The dangers incident to mining under deep deposits of sand have long been realized by operators in the northern anthracite field, and much has been done to prove the contour of the rock and vein croppings underlying these water-bearing deposits of sand and gravel.

Jan 1, 1915

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data' and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4'5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By E. H. Boswell, E. M. Cushing

The Mississippi embayment east of the Mississippi River is part of a vast geologic and hydrologic province. The abundance of water available is largely responsible for the agricultural history of the area and is perhaps the key factor in the rapidly accelerating trend toward industrialization. The multiple artesian aquifer systems that underlie the region and the alluvial aquifer along the Mississippi River are virtually undeveloped sources of fresh water in that they are yielding only a fraction of the water available. The potential yield of the 12 aquifer systems is estimated to be about 25,000 mgd (million gpd) of which only about 600 mgd is presently being withdrawn. The amount of water in storage in these systems is about 1600 trillion gal. Ground water having a dissolved-solids content of less than 500 ppm is generally available at depths of less than 1000 ft, and water having a dissolved-solids content of less than 1000 ppm is available in some places to depths of more than 3000 ft. Iron is the most common troublesome chemical constituent in the ground water. Water in varying amounts is also available from streams within the region. The amount of water which originates within the region and which leaves it as streamflow during a year averages about 50 million acre-ft (about 45,000 mgd). An additional 375 million acre-ft (about 340,000 mgd), which originated outside the region, leaves the region as streamflow during an average year. Some streams have considerable flow during periods of no precipitation and the water during these periods generally has a low dissolved-solids content. Large quantities of water from streams and waterbearing sands (aquifers) are available in the Mississippi embayment east of the Mississippi River. Most of the region is underlain by aquifer systems that will yield large quantities of water to wells, making ground water the most readily available source of fresh water. About 90% of the water used in the region is obtained from wells. Streams have been used primarily to dispose of, and dilute, wastes that have been dumped into them. The Mississippi, Ohio and Tennessee rivers, and the lower parts of the Tombigee and Yazoo rivers also serve as a means of transportation. This nominally water-rich region receives from 48 to 56 in. of precipitation in average years and is crossed by several large rivers. The largest, the Mississippi River, is the western boundary of the region discussed in this paper. The economy of the region is basically agricultural, but industry has become increasingly important since World War 11. The diversification and mechanization of agriculture have resulted in a surplus of manpower, most of which is being absorbed by the expansion of industry. Further industrial expansion probably will occur because of the available manpower, natural resources and economical transportation. Increasing demands on available water supplies will be made and the future economic growth of the region will be largely dependent upon wise utilization and management of the water resources.

Jan 1, 1969

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

Discussion of the paper of M. E. Lormbardi,. presented at the New York meeting, February, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 209 to 215. I. N. KNAPP, Ardmore, Pa.-Some years ago I made a swinging spider to carry a string of casing in a way somewhat similar to that described in this paper. The ground I tried it in was too soft for its successful operation. The spider had a central one-flange bushing to carry the slips. Under this flange and on top of the spider was a properly protected ball runway, or ball bearing, which permitted rotating the casing when it was in place and supported by the slips.

Jan 5, 1915

INTRODUCTION The regional characteristics of porphyry copper deposits in South America southward from Pantanos and Pegadorcito, Columbia, will be summarized. The age of formation of deposits spans the period from the Permian to the present. Where possible, the general characteristics and the individual structural features of the deposits are integrated into the plate tectonic model. Individual deposits cited in this chapter, located in Fig. 1, are the best known and most fully described, and form the Andean copper belt (Peterson, 1958). Smaller porphyry copper deposits fall both east and west of the line of large, high grade deposits (e.g., Chuquicamata and Toquepala) that make up the spine of this belt. Most of those smaller deposits (e.g., Mi Vida [Koukharsky and Mirre, 19761) are omitted from Fig. 1 and Tables 1 and 2, however. Neither the Andean orogen nor the individual deposits within it are as well de- scribed in the literature as are their counter- parts in the Cordilleran orogen of North America. Therefore, generalizations relying on regional geologic mapping, geophysics, and isotopic geochemistry lack details pertinent to this type of deposit in the Cordilleran orogen. The South American porphyry copper province has been described by Hollister ( 1974) to include most of the Andean orogen excepting the tin province of Bolivia. Porphyry copper deposits have not been commonly found within the tin belt, although copper-tin (e.g., San Rafael, Peru) and copper-tungsten (e.g., Llamuco, Chile) de- posits are known. James (1971) shows the depth to the Moho to be appreciably greater where the tin belt exists, but disclaims any genetic significance from the coincident appearance of the tin-tungsten province and the inhibition of porphyry copper development where the sialic crust thickens. Dates on tin mineralization in this belt (Clark and Farrar, 1973) are similar to some dates for porphyry copper mineralization known else- where in the Andean orogen. It seems that some mechanism is needed to explain the geographic separation of porphyry copper- molybdenum and simultaneous tin-tungsten- molybdenum metallization within the same tectonic system and appearing at similar distances from the trench. The thickened crust of the tin belt is one of the few known differences. Tables 1 and 2 list some of the most important porphyry copper deposits explored to date, but do not include Antaminas, Peru. or a number of other large skarn deposits

Jan 1, 1978

Jan 1, 1965

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By W. P. Sykes

In connection with a study of tungsten steels, Honda and Murakamil reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. Materials The iron powder used in preparing the alloys was obtained as follows : Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000" C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 per cent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon. The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly for several days at temperatures up to 1500' C. and for shorter periods

Jan 1, 1926

By Paul Sterling

1. INTRODUCTION. THE general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a "coal-breaker." This name is misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only in the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for domestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Oct 1, 1911

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By H. Kosmider, P. Coheur

New processes of blowing with an oxygen-enriched air or gas mixtures of oxygen and steam allow the steelmaker to produce, in a basic converter, a rimmed steel low in nitrogen (0.0020 pct), phosphorous (0.020 pct), and sulphur (0.020 pct). The physical properties (ductility) of the new steels are excellent. Furthermore, from the point of view of economy, these new methods of blowing offer outstanding possibilities. THE natural occurrence of geological deposits of iron ore and local economic circumstances led European blast furnace men to work large quantities of lean iron ore with a phosphorus content as high as 0.5 pct. The iron obtained from these ores generally contains 1.5 to 2.1 pct phosphorus, 3.6 to 3.9 pct carbon, 0.3 to 0.6 pct silicon, 0.04 to 0.08 pct sulphur, and 0.3 to 1.2 pct manganese. To produce steel from this pig iron, the steelmaker has at his disposal several processes. One of the simplest and most economical is the pneumatic process developed by S. G. Thomas in 1879. This process of steelmaking, called the Thomas process, consists of blowing through the bottom of a basic bessemer converter and is used widely in Western Europe, as shown in Table I. Due to the development of tonnage oxygen plants, this process has become more important because the use of oxygen offers new possibilities of steel manufacture. Not only may the quality of the steel be improved, but liquid pig iron also may be used, the composition of which does not meet the heat requirements of the blow with atmospheric air. It is not intended to present here a detailed scientific discussion of the basic bessemer process but rather to discuss briefly its industrial possibilities in the case of rimmed steel and when blowing with atmospheric air, oxygen-enriched air, or gas mixtures of oxygen and steam. This paper is based on the current practice at Klockner-Hüttenwerk Haspe's steel division, and at six Belgian and Luxemburg steel works. The latter are members of the Liege section of the C.N.R.M. (National Institute for Metallurgical Research) and are: ARBED, John Cocker-ill, Esperance-Longdoz, HADIR, Miniere et Metal-lurgique de Rodange, and Ougree-Marihaye, most of which are working with tonnage oxygen plants.' In order to avoid any misunderstanding, it should be noted that most of the techniques to be men- tioned, or similar ones, are used currently at many steel plants in Western Europe. Background The basic converters used in Europe have a capacity of 17 to 65 tons of steel, and are similar in shape to the one in Fig. 1. The lining is brick or rammed dolomite and has a life of 250 to 500 blows. The bottom is rammed dolomite and has a life of 40 to 80 blows. As far as we know, the type of blast used does not appear to have any influence on the life of the lining. Bottom life, on the contrary, depends very much upon the composition of the blast. It is only when

Jan 1, 1955

By Harry C. Wiess

PETROLEUM has come to be one of the most important and essential of the mineral re- sources of the nation. It is the most advantageous source of mineral fuels and of lubricants, and as such it has provided in large measure for the phenomenal development in our modern means of travel and in the facilities for transportation by land, sea, and air. Without it the remark- ably rapid industrial and social progress in our country during the past thirty years could not have occurred. In view of its important place and the fact that petroleum is irreplaceable and existent in limited quantities in nature, its conservation is essential.

Jan 1, 1939

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By F. F. Aplan

Mineral processing engineers have recorded an- other year of active research and development work. Most gratifying was the broadly based attendance at the Mineral Processing Fundamental (formerly Basic Science) Committee sessions at the 1968 Annual Meeting of the AIME. Because of the availability of good papers, the active discussion and the growing attendance, sessions have grown from one to three at the annual meeting. Prof. M. C. Fuerstenau of the University of Utah will chair the Mineral Processing Fundamentals Committee for the next two years and we may thus be assured of continued active leadership. The name change from "Basic Science Committee" to the more descriptive "Mineral Processing Fundamentals Committee" approved by the MBD executive council is a welcome improvement. Our profession continues to attract the interest and cooperation of those in other professional groups. The 1968 Engineering Foundation Particulate Matter Conference, under the chairmanship of John Karpinski of Bethlehem Steel, was devoted exclusively to comminution this year. It attracted conferees from five continents and served as a particularly stimulating source of interchange of knowledge from many technical fields. Next year's conference will be under the chairmanship of Professor L,. G. Austin of The Pennsylvania State University. This conference plus the Symposium on Wettability and Flotation to be held at the annual American Chemical Society meeting in Minneapolis in April indicates the success achieved in the inter-disciplinary approach to problems. Other evidence of this spirit of professional cooperation is the forth- coming book on Size Reduction edited by D. W. Fuerstenau. This is the outgrowth of an AIChE symposium on size reduction held in 1965.

Jan 2, 1969