Search Documents

By E. J. Westerman

Prealloyed powders of nickel-base superalloys were sintered to almost theoretical density in short sinterilzg times. It was ascertained that the rapid densification was caused by a small amount of liquid phase at the grain boundaries, which apparently ovriginated by incipient melting at temperatures considerably below those at which macroscopic melting of the compacts occurred. An increase in the quantity of liquid phase present during sintering-, caused by an increase in the sintering temperature, increased the densification rate, but resulted in a decrease in the room temperature tensile propevties. NICKEL-base superalloys, which presently comprise an important group of high temperature alloys, are difficult to fabricate by the forging, casting, and machining operations presently used. As it was felt that fabrication by powder metallurgical techniques might offer advantages in the production of super-alloy parts, a basic investigation of the most important process in the sequence of powder metallurgical operations, the sintering process, was undertaken on Rene 41, Udirnet 500, and Nimonic 90 and 100 powders. These alloys age harden by the precipitation of the ? Ni, rA1,Ti) phase. Nickel-base superalloys of the Nimonic type have been fabricated by powder metallurgical methods, and their mechanical properties reported in detail.' Other alloys for high temperature service which have been fabricated by powder metallurgical methods include a Co-base alloy of the Vitallium type;2,3 alloys with a Co-Ni-Fe-Cr base;4 stainless steels;5'6 Cr-W-Co alloys;" and a Co-base alloy, X-40.8 METAL POWDERS The superalloy powders investigated were: a) a prealloyed at.omized Rene 41 powder; b) a prealloyed atomized Udirnet 500 powder; c) a prealloyed atom-

Jan 1, 1962

By L. C. Uren, J. Domerco

That the diameter of a well through the oil-producing formation has an important influence on its rate of production is a principle accepted by many petroleum technologists. Knowledge of this principle extends back at least to the time when Slichter and King1 confirmed it in a study of the dynamics of flow of water through porous strata into wells. More recently, the senior author2 and his associates3 have produced qualitative experimental data confirming the principle as applied to drainage of expanding oil and gas mixtures, and suggesting that wells of large diameter, or wells having cavities about them within the reservoir rock, enjoy a material advantage in competition with wells of ordinary diameter. Apparently, however, no one has produced experimental data designed to indicate quantitatively the advantages that wells of large diameter possess in comparison with wells of normal diameter producing under comparable conditions. This paper reviews some preliminary experimental results of this kind, together with some conclusions and speculations based thereon, which further emphasize the importance of well diameter as a factor in determining the efficiency of oil recovery. Theoretical Aspects of Radial Flow of Fluids into Wells It is well understood that in a reservoir rock of uniform thickness and permeability oil and gas flow toward the wells along radial lines. The cross-section of the reservoir rock through which the fluids must move becomes ever smaller as the wall of the well is approached. The velocity of flow must therefore correspondingly increase, an effect that is accentuated by the rapid increase in volume of the fluid due to release

Jan 1, 1935

By C. W. Spencer, F. N. Rhines, R. J. Knight

Ametallographic study has been made of the peritectoid transformation as it occurs in two Ag-A1 alloys, containing 6.0 and 6.9 wt pct Al, respectively. After equilibrating at 475°C, these alloys were transformed isothermally just below the peritectoid temperature which lies at about 450°C.1-3 Peritectoid transformation in this alloy system consists in the reaction of a and 5 to form µ. The crystal structures of the a, µ, and 5 phases have been determined as face-centered-cubic, 6 manganese, and hexagonal-close-packed, respectively. At the peritectoid temperature their equilibrium compositions are approximately 5.85, 7.02, and 7.24 wt pct (19.92, 23.2, and 23.8 atomic pct) aluminum."" The transformation might be expected to occur principally at the interface between the a and 5, but such is not the case. Instead, the major part of the transformation occurs by the direct (and perhaps initially diffusionless) conversion of 5 to µ. The composition range of the forming µ nearly overlaps that of the parent at the temperature of transformation" so that little, if any, composition change is required. Transformation proceeds by the nucleation of µ at points upon the external surface of the sample and sweeps through the 5 phase, leaving the a initially almost undisturbed. Subsequently, the a phase participates in the transformation by being partly or totally converted to µ. Specimens approximately 1/4 x 1/4 x 1/16 in. were cut from cast ingots, previously equilibrated 68 hr at 588°C. The specimens were held for 3 hr at

Jan 1, 1958

By R. A. David, D. J. Vink, D. L. Katz

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By R. A. David, D. L. Katz, D. J. Vink

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By C. H. Li, S. H. Bendel, J. A. Sartell

Small additions of Mg to a 62 Cu-38 Ni alloy reduce the oxidation yates drastically between 500° and 850°C. Metallographic examination of the oxide scale disclosed a continuous network, identified by X-ray diffraction as (Ni, Mg)O solid solutions, located along the former alloy grain boundaries. This network acts as a barrier to diffusion. It is thought to result from the segregation of mg to the alloy grain boundaries. Oxidation occurs preferentially in these regions because of the presence of this more active element. To substantiate these ideas, homogenized alloys ulere oxidized. No oxide network was produced and oxidation rates were the same as for the parent 62 Cu-38 Ni alloy. An interesting aspect of the oxidation of the 62 Cu-38 Ni alloy previously described by the present authors, is the relationship between oxidation kinetics and changes in the microstructure of the oxide.' The oxide scale on these alloys consists of two layers: a thin layer of CuO outside a much thicker layer of Cu20 in which particles of NiO are dispersed. In addition, immediately beneath the oxide-metal interface there is an internally oxidized zone in which NiO particles are dispersed in a copper-rich alloy matrix. Experimental observations on the growth of the individual layers under isothermal conditions have led to the conclusion that the rate-determining step in the oxidation of this alloy is the diffusion of anions through the Cu20 layer. It has been found that this diffusion rate is increased by the recrystallization of the outer CuO layer. Willardson and Gorton have reported that the addition of magnesium to the 62 Cu-38 Ni alloy causes a decrease in the oxidation rate.2 The present investigation was undertaken in order to determine the mechanism by which magnesium additions improve the oxidation resistance of the 62 Cu-38 Ni alloy. EXPERIMENTAL PROCEDURE Fifty-gram ingots of Cu-Ni alloys were prepared by vacuum melting materials of 99.999+ pct purity. These ingots were then remelted in a He atmos- phere and magnesium added in the form of a previously prepared and analyzed Cu-Mg master alloy. This procedure was necessitated by the high reactivity of pure magnesium at high temperatures. The proportion of the alloying elements was adjusted so as to obtain alloys with the desired magnesium content while maintaining a Cu-Ni ratio of 62 :38 by weight. (All alloy compositions will be given in weight percent.) Since it was considered desirable to study the oxidation of only single-phase, solid-solution alloys, it was necessary first to determine the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy. A series of melts with various magnesium contents was made, homogenized by annealing for 48 hr at 975OC, then cooled in the furnace. Metallographic samples were prepared, etched in a potassium dichromate solution and examined at XI500 for the presence of a second phase. The alloys were then chemically analyzed and it was found that the approximate limit of solid solubility of magnesium in the 62 Cu-38 Ni alloy was 1 pct Mg. The ingots containing less than 1 pct Mg (0.19, 0.29, 0.58, and 0.87 pct Mg) were cold-rolled down to thicknesses suitable for oxidation experiments and specimens for gravimetric studies were cut to dimensions of 3.0 by 1.5 by 0.05 cm, specimens for inert marker studies, 0.6 by 0.6 by 0.17 cm. These were heat-treated in a protective atmosphere at a temperature (975" C) well above the oxidation temperatures and furnace-cooled to insure structural stability of the alloy during oxidation. Immediately prior to oxidation, the specimens were chemically cleaned by immersion for 1 min in a solution of 2 parts nitric acid, 1 part acetic

Jan 1, 1961

By Lester Uren

The fluid level maintained in wells pumped for oil is an important factor in deter-mining their productivity but one that has received little attention in the literature relating to petroleum-production technology. In the present paper the writer undertakes to show how and to what extent fluid level influences productivity and suggests the use of a fluid level indicator as an aid to the oil producer in maintaining the fluid surface within the well at the proper position. IT is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended, should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the .ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size, of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well.. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 2, 1925

By C. D. Dolman

Since the outbreak of the war we have discovered in the united States minerals of which there was no general knowledge, and which compared very favorably with anything that could be found in any foreign country. One of these was magnesite, or the carbonate of magnesium as it occurs in nature. This mineral crystallizes in the rhombohedra1 form, has a specific gravity of 3.00, molecular weight of 84.4, molecular volume of 28.1, and a hardness of 3.5 to 4.5.1 Had it not been for the development of the California deposits of this mineral and the discovery of immense new deposits in Stevens County, Wash., the production of steel during the war would have been more seriously handicapped than it was. Now that the war is over, we face the possibility of competition with the cheap Austro-Hungarian magnesite; and while that may not be so cheap as it was before the war, adequate protection should be given the producers in this country to insure the full development of our own resources. The consumption of magnesite in the United States in 1913, the year preceding the war, was 172,591 tons of calcined and 22,872 tons of crude magnesite. Less than 3 per cent. of this amount was produced at home. At the present time, practically all of the magnesite used in the United States is produced at home. Expensive plants have been constructed, extensive exploration work done, and production pushed to the utmost to supply the necessary requirements of the war. Thus a considerable industry has been built up within our borders. Some magnesite has been imported from Canada and Mexico, but the Canadian ore was of an inferior grade and could not be used satisfactorily. During the year 1918, production decreased in both the United States and Canada; the production in the United States was 225,000 tons in 1918 as against 315,000 in 1917, and in Canada 39,365 tons in 1918 as against 58,090 in 1917. This decrease was mainly due to over-production during 1917, the domestic demand being only 300,000 tons. The material produced and sold in the United States must contain, in the crude form, not more than 3.5 per cent. silica and 2 per cent. lime;

Jan 1, 1920

By S. Leber, R. F. Hehemann

Diffusion coefficients for the Cb-W system were measured using couples prepared from poly crystalline, commercially pure metals. The diffusion coefficients, measured in the temperature range between 1700° and 2300°C, decreased exponentially as the tungsten concentration was increased from 0 to 50 at. pct, then decreased abruptly at higher concentrations. A decrease of two orders of magnitude was observed over the entin? compositional range. The diffusion coefficients were in the range defined by the self-difiusion coefficients of the individual elements, indicating their general validity. An activation energy of 60,500 cal per mole was measured for the 20 pct W composition. Such low values, when compared with energies over 100,000 cal per mole for the pure constituent elements, indicated that transport mechanisnzs more rapid than volume diffusion were contributing substantially to inter dijfusion. Difference should, therefore, be expected between these data and the intrinsic diffusion coefficients. These differences should be significant in the kinetics of 'transport phenomena in practical systems. CONSIDERABLE attention has been devoted in recent years to the mechanical behavior and other properties of the refractory metals and their alloys. The Cb-W system has been of special interest as a base for the development of more complex compositions of commercial interest. In spite of the importance of mass transport to all aspects of elevated-temperature behavior, and especially to the production of alloys by powder-metallurgy techniques, little attention has been paid to diffusion in the Cb-W system. Results from a previous study of this system1 appeared to be anomalously high. The present investigation is, therefore, an attempt to obtain more accurate diffusion coefficients in this system. Intrinsic diffusion coefficients, of primary importance from the theoretical viewpoint, can only be obtained accurately from studies utilizing compositional gradients approaching zero. However, many practical problems involve diffusion under significant concentration gradients. The diffusion coefficients determined in this investigation were, therefore, obtained from couples prepared from elemental metals. The data obtained should be of value in the analysis of problems such as homogenization during powder-metallurgy alloying or reactions between base and clad in coated structures. In this vein, the investigation was conducted on poly crystalline materials of commercial purity. PROCEDURE Diffusion couples were prepared by sandwiching a columbium sheet between two sheets of tungsten. The composite was welded around all edges, the tungsten forming a protective can for the columbium. The composite was soaked for 4 min at 1600°C in a hydrogen-atmosphere furnace, quickly forged to 40 pct reduction in thickness, and then rapidly cooled to room tempera-

Jan 1, 1967

By Joseph Jensen

FROM Aug. 31, 1937, until Apr. 30, 1939, there were 40,872,610 bbl. of oil run to storage in California; from Apr. 30, 1939, to Aug. 31 of the same year 5,512,912 bbl. were withdrawn from storage. But from Aug. 31, 1937, to Aug. 31, 1939, the number of producing wells in the state has increased from 17,706, with a potential production of 1,323,202 bbl., to 18,910, with a potential of 2,302,282 bbl. Thus, in a period of two years, during the first 20 months stocks increased over 1/3 and during the following four months stocks decreased 1/30. In the same two years the number of productive wells increased 1/15 and potential increased 3/4. Undoubtedly, the large increase in stocks created the pressure that caused the reduction in stocks that followed; yet this has come about in spite of the larger number of wells and higher potential. Cause of the change was the adoption on May 17, 1939, by the Central Committee of California Oil Producers of a uniform method of oil curtail-ment for all wells throughout the state. Acceptance of the method in the four months following adoption by practically all fields in California indicates that producers generally are convinced of its merit and fairness. True, some operators still overproduce, but the restraint practiced by the remainder of the industry has been sufficient to turn a situation headed for chaos into one of reasonable stability. Credit for this change goes to the industry itself, because it has all been accomplished under voluntary oil curtailment.

Jan 1, 1940

By Edward Steidle

IT has been said that "the command of nature has been put into the hands of man before he knows how to command himself," and what we see about us gives particular emphasis to this observation. If this condition be granted, the vaunted boast of school and college, of the institution that had the training of this generation, and of its fathers, and of its grandfathers, the boast that education is a "preparation for life," stands exposed as a hollow claim, or as a ghastly, cynical conception of life, or else education has fallen far short of its intentions. It has been evident for some time that education was not meeting the fullest expectations of society. In recent years there has been a deal of speculation indulged in by both laity and faculty in regard to American education and American civilization, and some few and sporadic changes have been effected. Today, however, there is no longer time for mere hypothetical considerations; we are faced with certain definite facts and confronted with obvious conditions that will not wait for fine-spun theories. If educators do not put their house in order, someone else will do it for them. The trends in mineral industries education must be in harmony with this general realignment that is today visible on the educational horizon, and only as these trends are in conformity with this movement can they be called sound. Two questions, then, confront mineral industries educators: (1) What are the trends in mineral industries education, and (2) how do these trends correlate with the major educational movements of the day?

Jan 1, 1933

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By James Gayley

The lining of the hearth and bosh of a blast-furnace has naturally come to be considered its weakest part, being subject not only to abrasion, but also to intense chemical action. In order to provide against rapidity of wear, it was formerly customary to build the lining from the mantle to the top first, and to put in afterwards the hearth and bosh, drawing the latter into a recess that had been reserved for it in the upper lining. At some works this practice still prevails ; but through the progressive development of cooling-devices, it has become possible to protect the bosh so well as to make it the most durable part of the furnace. The main question now is, by which one out of several methods the best economy results can be obtained. The plain bosh-jacket, made of wrought-iron or steel, and frequently called the air-cooled jacket, was a great improvement over the crinoline-construction formerly in vogue; but it was difficult in many cases to persuade furnace-managers, that in order to secure its best effects, they must discard the thick bosh-walls and put in comparatively thin ones. Mr John M. Hartman, who did more perhaps than any one to extend the use of these jackets, invariably contended for a 13-inch wall, the thin wall being an essential part of this construction. Later, a coil of pipe was placed just inside the jacket, through which water, circulating freely, contributed further to the proper maintenance of the walls. Undoubtedly much better results have been obtained in practice where the iron jacket has been supplemented by a coil in this way. It is safe to say that this combination of water-coil and jacket is much better than external sprays on the jacket; but it does not prevent the brick-work from cutting entirely away, which enlarges the bosh to that extent and interferes with the economy and output of the furnace. In case of leakage or stopping-up of the pipes, they cannot be replaced. A leading blast-furnace manager who is now using this construction

Jan 1, 1893

By Joseph Hartshorne

This plant is situated in the borough of Pottstown, on the banks of the Schuylkill river, between the Philadelphia and Reading Railroad and the Schuylkill Division of the Pennsylvania Railroad, on a plot of about 125 acres, most of which is reserved for future extensions. About 45 acres are to be used for houses, 40 of which have already been built. The accompanying plan will give a clear idea of the general arrangement of the works. Beginning at the lower or eastern end, the first building is the basic-cinder grinding-plant. At present, it consists of a 2000 mm. Jenisch ball-mill (Kugelfallmühle) similar to those used so extensively for grinding basic cinder in Europe. It was built by Herman LÖhnert, of Bromberg. The mill is very simple in design, and efficient in execution. About 13 horse-power is required to run it, and the average output is 20,000 pounds in 10 hours. The best work we have done is 29,000 pounds in 10 hours, with perfectly dry cinder. From 95 to 98 per cent. of the product will pass through a sieve with 100 meshes to the inch, while from 70 to 75 per cent. will pass through a 150-mesh sieve. The mill has been in service since last March, part of the time on double-turn, and the renewals and repairs have been very slight. The product of the plant is sold as a fertilizer. It runs from 18 to 24 per cent. in phosphoric acid, about 14 of which is reverted. The merits of this fertilizer were explained by Mr. W. H. Morris, at the Baltimore meeting of February, 1892 (Trans., xxi., 232), and by Mr. W. B. Phillips, at the Birmingham meeting of 1888 (Trans., xvii., 84). The results obtained by its use in Europe, where over 600,000 tons were used last year, are well known. Near the cinder-grinding plant will be situated the new machineshop, which is now being erected. The next buildings contain the brick-making plant and ovens.

Jan 1, 1893

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

By T. G. Chapman

THE writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, fol-lowed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encour-aging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its pos-sible advantages and immediate field, and give some results obtained on a laboratory scale.

Jan 1, 1939

By Meng-Cherng Sun, Fun-Den Wang, David M. Ropchan

A proposed technique for improving coal-mine roof stability by softening parts of coal pillars along the sides of entries developed from structural analysis is presented. This technique is based on the transference of the high stress concentration in the roof near the upper corners of a rectangular opening to the roof rock and coal over the solid away from the opening. This transferral is accomplished by softening parts of the coal pillars by drilling a series of parallel holes into the coal in the ribs and face of the entry prior to advance. The effectiveness of the pillar softening in terms of reducing the opening width (so that the stress in the roof near the corner is equivalent to that of a narrower opening) ranges from 3 to 5 ft for a 16-ft entry using a series of 4 to 5-ft-deep parallel drill holes of 3 to 6-in.-diam on a 1 to 2-ft spacing for a particular geology. Pillar softening should be highly effective in controlling roof where cutter-roof cave conditions exist, because this technique reduces the high stress concentration in the roof at the upper corners of the opening. It may also be effective for reducing tensile roof failure and coal rib sloughing for certain specific geological conditions. This technique appears to be a simple, effective, and practical method that can be used to supplement conventional roof support methods of roof bolting, timbering, roof truss, and other existing methods in underground coal mines. The authors consider the technique feasible and believe that it merits underground trials.

Jan 1, 1975

By A. G. Taylor, H. P. Ehrlinger, U. C. Tainton

FOR the last 15 years lead has been the standard material for anodes in electrolytic zinc production and it has been generally accepted that this lead should be as free as possible from impurities. Laistl says, "Next in importance to the purity of solution is the purity of the electrodes and tank lining material. The purest lead obtainable should be used for anodes." The same conclusion is expressed by Ingalls2 and by two German investigators who say that experiments have demonstrated that the purer the lead, the greater is its resistance to corrosion during electrolysis.3 Pure lead, however, while the best material hitherto available for anodes, is not entirely free from objection. The plain lead anode gradually disintegrates under electrolysis, so that the life of an anode, say 1/4 in. thick, is frequently not more than two years. Part of the lead from the anode finds its way to the cathode, lowering the purity of the deposited zinc and decreasing the hydrogen overvoltage. The rest of the lead that comes from the disintegration of the anode goes into the manganese dioxide which is precipitated in the cells, rendering unsaleable what might otherwise be a valuable by-product. Yet a further disadvantage of plain lead anodes comes from their tendency to bend or buckle during electrolysis, as a result of intercrystalline oxidation. This makes it necessary to use a fairly aide spacing between anode and cathode to avoid short circuits, and thus leads to a higher power consurnption than would otherwise be necessary. The power consumption is also affected by the high decomposition voltage at a lead peroxide surface.

Jan 1, 1929

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923