Search Documents

By Oliver Bowles

WHILE vast quantities of limestone and dolomite. are used in metallurgy, the estimated production in 1926 being 23,860,000 tons, there are many problems connected with their use which have not received adequate study. The literature of metallurgy is notably lacking in comprehensive discussions of fluxing or furnace stone. Approximately 900 lb. of limestone is used for every long ton of pig iron produced in the blast furnace, but this important constituent of the charge receives little attention compared with the intensive study that has been applied to ores and fuels, the other important constituents of the charge. In an effort to elucidate some of the doubtful points, the writer has made a wide review of metallurgical literature, and has had the disappointing experience of finding not more than a paragraph or two on metallurgical stone' for each two or three thousand pages of literature reviewed. Furthermore, the limited information supplied is in some instances contradictory and even absurd. For example, a correspondent in a reputable metallurgical magazine classifies magnesia and silica together as impurities in flux "that must be melted and run off as slag." From the furnace operator's viewpoint it is desirable that as complete knowledge as possible be obtained concerning the effects of chemical composition and physical character of the stone on its action in the furnace and on the quality of the metal produced. A better knowledge of these features is advantageous also to the quarry operator in that it enables him to work more intelligently in producing stone that will best satisfy the metallurgists' requirements. The following pages comprise a brief compilation of data now available. Much of the information is well established and probably acceptable to most metallurgists. On some points there is room for debate, and the chief purpose in presenting a paper at this time is to arouse discussion which will throw more light on controversial points and thus assist the author in preparing a more comprehensive and accurate discussion of metallurgical limestone problems.

Jan 1, 1928

By Paul Billingsley

IN THEIR course across Ecuador, the Andes fail to show the mineral wealth with which they abound in Peru, Bolivia, and Chile. This may well be due merely to the concealment of recent volcanic ash and dense tropical jungle, but at any rate Ecuador has lacked the stimulation to development and progress afforded to the southern countries by the mines of Cerro de Pasco, Potosi, etc. 1 There is, however; in Ecuador, near its southern border, one mining district that, in recent years under North American management, has become a steady producer of mineral. wealth and. a community in which the sanitary and mechanical elements of modern life are displayed, for ;the first time, to the Ecuadorians of the lowland forests. The mining district of Zaruma is .situated in the province of El Oro, near the southwestern corner of Ecuador, about 50 km. (31 mi.) from the coast. Pizarro's first landing on the mainland was at Tumbez, at the mouth of the river that drains the Zaruma area; and the gold so abundantly found in this Indian town was soon traced to its source. In 1549, Mercadillo, one of the original (band, reached Zaruma, having worked his way up-stream through canyons that .are now regarded as impassable. The Spaniards proved themselves efficient prospectors, finding practically every orebody in the district as yet discovered; and, working

Jan 10, 1925

By Chester A. Fulton

APATITE, the most abundant crystalline phosphate mineral, is found in igneous rocks and probably is the primary origin of all other phosphates, whether mineral or organic. Its chemical formula may be expressed as Ca5(Cl,F) (PO4) 3. The chlorine may be replaced almost entirely by the fluorine. It is found in large or small hexagonal prisms, usually of a vitreous luster and a green or red color, but also violet, white, or yellow. It is found largely as an accessory mineral in granitoid rocks. Its hardness is 4.5 to 5 and its specific gravity is about 3.2. There are many other phosphate minerals-for instance, amblygonite, autonite, collophane, lazulite, monazite, pyromorphite, torbenite, triphylite, turquoise, vivanite, wavellite-with base elements of calcium, magnesium, iron, aluminum, manganese, lead, cerium, lanthanum, lithium, or several of these in combination and with various amounts of water of crystallization. However, these phosphate minerals have but little value save as specimens for mineral collections, the exception perhaps being turquoise. While large deposits of igneous apatite are mined today for the production of fertilizers and chemicals, more than 90 pct of the world phosphate production is derived from secondary apatites, called phosphorites. These calcium (and magnesium, aluminum, and iron) phosphates have been formed in the alteration of sediments by solutions containing phosphoric acid. Such solutions have come from the weathering or leaching of igneous rocks containing apatite, bone deposits of prehistoric animals and marine life, or guano deposits (excreta of birds). These phosphorites are mostly alterations of phosphatic limestones that took place slowly over many years. Whether it is apatite or phosphorite that is being produced, it is known in the trade as "phosphate rock." The sedimentary phosphate deposits are of marine origin. Some, as laid down, were rich in phosphate or have become so by subsequent subaqueous action and have not been further enriched since emergence from the sea. Some were originally phosphatic limestones or marls from which calcium carbonate was dissolved away by waters containing carbon dioxide, in which calcium carbonate is much more soluble than

Jan 1, 1949

By Boyd Dudley

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Alden H. Emery, J. J. Forbes

The data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in six coalmining states. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand and transporting it from the working face to the surface. The data thus obtained were considered from two angles; namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be made to discuss the former factor in this paper. ConDitions of Mining The mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. All of the coal mined was bituminous, from beds 30 to 120 in. thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by shortwall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face wets done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal were commonly used, although some roof work was done with jack-hammers and a little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1800 to 3600lb. With few exceptions, coal was won at the face by dry methods, that is to say, no water was employed for wetting down the dust either during undercutting, loading or transportation. Observations of Sources of Dust The common sources of coal dust as observed, arranged by decreasing amounts, were as follows: (1) Undercutting with mining machines; (2)

Jan 1, 1927

By Malcolm Wilson

THE year 1923 was one of great importance in northern Louisiana and southern Arkansas, so far as the' development and expansion of previously discovered oil and gas fields were concerned. However, the search for new fields failed to produce a single discovery that led to important development during the period; in this respect, the year was one of discouragement to the prospector. During the winter and spring months, an especially active "wildcat" campaign was in. progress in southern Arkansas, and a large number of tests were drilled in northern. Louisiana but this activity subsided during the summer and fall. By the close of the year, only routine drilling was in effect in the fields; and only two new areas-Cotton Valley, in Webster Parish, and an area in Union Parish, La.-were showing any important activity because of favorable oil showings. Further drilling is contemplated in both of these areas, and the present feeling is that one or the other may produce the next oilfield in this territory. Briefly, the development of the Smackover field was the overshadowing event of the year. In. southern Arkansas, important development also took place in the East El Dorado, Stephens, and Irma fields; but all of these were relatively small. In northern Louisiana, many new oil wells were drilled in the Bellevue field, and many new gas wells in the Monroe field. In the old Caddo field, a large number of the deep Woodbine wells were plugged back to the "chalk rock," where a high gravity oil is obtained. In the other fields, only a few small wells were drilled. Therefore, Arkansas, furnished the real development of the year in this area. The production for the year showed a material increase over that of 1922, due, chiefly, to Smackover, and practically altogether to the Arkansas fields. In Louisiana, every field, except Caddo, Bellevue, and Elm Grove, showed slight to marked declines; while in Arkansas, El Dorado was the only field that declined throughout the year.

Jan 3, 1924

By Alexander L. Field

The rate of elimination of carbon largely controls the time required to make a heat of steel by the basic open-hearth process and to an important degree determines the cost of refining. Practical experience has led to the generally accepted belief that the use of slags relatively high in iron oxide, such as are required to bring about rapid refining, leads to a certain sacrifice of quality in the product. As a consequence, a compromise must be made between the exceedingly slow rate of carbon drop which would correspond to the ideal case and the rapid rate which would best satisfy the condition of minimum cost. An increase in rate of refining necessarily implies an increase in the concentration of iron oxide dissolved in the metal. However, even for the infinitely slow rate that corresponds to slag-metal equilibrium, the metal would contain a certain definite concentration of dissolved iron oxide. It is a matter of great practical importance, therefore, to determine the quantitative relation between the minimum or equilibrium concentration of iron oxide in the metal and the higher concentrations which must actually obtain in practice. The present paper is devoted to the development of certain equations, derived from the established laws of physical chemistry, which will enable this relation between rate of refining and the degree of oxidation of the metal bath to be computed from operating data. So attempt is made to exhaust the possibilities of this general method of treatment. In considering rate of refining, attention is mainly confined to rate of carbon elimination. However, the equations are of a more general nature and their application may readily be extended. The results of the preliminary calculations given herein indicate that increased rate of refining may have a decided effect in increasing the concentration of iron oxide dissolved in the metal. The uncertainty which attaches to the calculated value for this relationship arises in part from probable errors in experimental data on which the calculations are based, and in part from the lack of complete or favorably disposed information on basic open-hearth practice. When the relation between rate of refining and degree of oxidation of the metal has been more accurately established than has been done in the present paper, it will then become possible to consider what comprises

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By Ivor Hawkes

A wide variety of borehole gages have been developed for measuring rock stress. They all operate on the principle that stress changes around a borehole result in deformation that can be measured by the gage and interpreted in terms of the stress change either by calculation or calibration. In general terms, gages that comply with the borehole deformations are referred to as “deformation meters” and those that restrain the deformations by reason of their rigidity are referred to as “stress meters.” The main advantages claimed for stress meters are: their “stress” sensitivity is much less dependent on the rock modulus than that of deformation meters, and they are clamped firmly in the borehole. The use of each of the borehole gages developed for stress determinations in rock in the main has been confined to the laboratory responsible for its development. To be generally accepted a gage must meet the following specifications : 1) Gages to be left in place to measure stress changes must be relatively cheap, and if possible recoverable, so that large numbers can be used to obtain an overall picture of the changing conditions. This, of course, is not necessarily the case for recoverable gages designed for absolute rock stress measurements where usually only one or two gages are involved. 2) For use in the adverse environmental conditions encountered underground, it is essential that gages be robust, stable, and unaffected by high humidity, corrosive water, or dust. 3) Highly qualified technicians are rarely employed specifically for rock mechanics studies in mines or on civil engineering sites and there- fore gages designed for measuring stress changes must be easy to set and

Jan 1, 1972

By W. M. Peirce

THE PROCESSES USED FOR THE rolling of zinc are not novel or unique in a mechanical sense. There has not been so widespread a tendency toward heavy slabs and mechanical handling, and toward 3-high and continuous mills as has taken place with steel and with some of the other nonferrous metals. Those respects in which the rolling of zinc differs from the rolling of other metals center around two facts. First, the hexagonal zinc crystal has only one plane of easy slip: namely, the basal plane. Fortunately, however, the crystal twins readily on any of the pyramidal planes, thereby creating new basal planes favorably oriented for relief of the stress which has caused twinning. Second, the recrystallization temperature of zinc is little above room temperature and for very pure grades of zinc may in fact, be at room temperature for severely strained material. The practical effect of these two characteristics of zinc will become evident in the later discussion. First, it is necessary to give some attention to the melting and casting of billets for rolling. Reverberatory furnaces are commonly used for melting. These vary over a wide range of capacity from as low as 5 tons to 100 tons or over. Low-frequency electric furnaces have also been used with satisfactory results. Arc Furnaces are, of course unsuited to a low-melting and lute-boiling metal, such as zinc. To minimize oxidation and volatilization losses in the furnace, the temperature should be kept below 500°C. With this temperature in the melting furnace, a suitable pouring temperature in the neighborhood of 460°C can he maintained at the mold when a transfer ladle is used for pouring.

Jan 1, 1948

By C. P. Fiske

The pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers, and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance come the condensers, as large numbers are used in the manufacture of spelter, and improvements in quality result in material decreases in working cost. While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are conccrned. Materials Bond Clay.—The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather it in the accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later) accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons with the clay as usually handled.

Jan 1, 1918

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By John L. P. Campbell, Warren J. Jackson

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By F. W. Lake

The ultimate production from a natural reservoir of petroleum is inversely proportional to the gas-oil ratios existing during the producing life of the reservoir whenever gas is the major expulsive force in the recovery. In other words, in the period during which gas is the major expulsive force the ultimate production will be increased if the gas-oil ratio is decreased, and vice versa. This condition prevails in the greater number of the present producing districts. While this relation is difficult to prove from actual operation, on account of the present paucity of detailed observations, it must be admitted after a study of the forces and conditions governing the recovery of petroleum from natural reservoirs. Where gas and oil exist under pressure in sand interstices and water movement is not freely possible, the force expended in moving the oil to the well is the expansion and movement of the gas through the pressure differential existing between the interior of the reservoir and the well. If pressure and solution conditions in the untapped reservoir are such that the relation between gas and oil volumes at atmospheric conditions is as 100:1; and if during the producing period, until the gas is exhausted, the relation between the gas and oil volumes produced is 300:1, it follows that only one-third of the oil has been produced and the remaining two-thirds cannot be recovered unless some extraneous force is introduced into the reservoir. This serves to illustrate the importance of gas-oil ratio control during normal producing operations. Gas-oil Ratio Control Eliminating natural conditions in a reservoir, which govern gas-oil ratios, such as the physical properties of the oil and gas, the physical characteristics of the reservoir strata and the original pressure and solution conditions in the reservoir, which cannot be controlled by operation practice; and also eliminating operating conditions that apply to the reservoir as a whole, such as well spacing, well locations, relative completion dates, various penetrations and drilling practice; there remains but one condition in each well that influences the gas-oil ratio and that is

Jan 1, 1928

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957

By G. H. Wigton

The oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods are unsatisfactory, as the lead smelters heavily penalize the largc amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this internal, an expcrimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments .were resumed. The highly infusible flotation tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent, common salt showed nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus

Jan 1, 1926

By G. K. Manning, A. R. Elsea, C. R. Simcoe

It was found that a critical boron content exists which yields the maximum boron-hardenability effect in hypoeutectoid steels, as was predicted from the mechanism proposed in a previous paper. The hardenability of boron steels with boron contents between 0.00005 and 0.0017 pct was dependent on the boron content, austenitizing temperature, quenching temperature, and austenite grain size. The effects of these variables on hardenability can be explained by the mechanism previously proposed for the boron effect. A MECHANISM has been proposed to explain the effect of boron on the hardenability of steel.' The proposed mechanism assumes that transformation particles nucleate at concentrations of lattice imperfections where the energy level is high, and

Jan 1, 1957

By John. C. Reed

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62° W. The average dip is about 67° SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30° W. and average dips about 75° SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30° for the south-west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By Samuel S. Wyer

The magnitude and economic importance of the problem of correctly valuing natural-gas leaseholds become evident when me consider that: (a) Natural gas is handled in 55 per cent. of the gas distributing plants in the United States. (b) Present known natural-gas acreage forms 47 per cent. of the total known mineral-land acreage in the United States. (c) Five acres of land are now required to protect and maintain continuous service to each of the 2,000,000 domestic natural-gas consumers in the United States. (d) The cost of acquiring and maintaining this acreage of an expendible resource represents a substantial part of the cost of the natural-gas service to the consumer. (e) "The right of a citizen by means of his ownership of or his mining leases on land to draw gas from beneath its surface is property and sometimes valuable property."' A large number of other court decisions have established the basic legal principle that the right to drill for gas within a given area constitutes an interest in the land itself, and is necessarily an exclusive property right. Definition of Vested Interests or Rights "Vested interests are economic interests which are legally recognized to be such that they cannot be impaired by public action, directly or indirectly, without indemnification. Vested interests are largely property interests. The recognition of an interest as a vested interest gives it some of the attributes of property, and by American courts it would be comprised in their very inclusive concept of property. Otherwise than through property, vested interests generally arise through contract."

Jan 1, 1917

By David B. Reger

The exhaustion of oil and gas in the United States is proceeding at a rapid pace. This is especially true in fields where the light oils that furnish the most fuel for internal-combustion engines arc found, leading to a late estimate by Arnold that the petroleum resources are 36 per cent. exhausted.l The further remark by Dr. David T. Day at the New York meeting of the Institute, in February, 1916, that the operators of the country are now scarcely able to supply the ever-increasing demand for gasoline, leads the writer to believe that a determined effort will soon be made to secure deeper producing horizons in those regions that now furnish high-grade oil, and in which pump stations and pipe lines offer convenient means for the economical handling of new production. A study of Arnold's table shows further that the States that produce paraffin oil exclusively are 45 per cent. exhausted, this figure being much higher than the average of paraffin and asphalt States altogether. The most extensive of all the paraffin-oil-producing areas is the Appalachian Field, extending with the Appalachian Geo-Syncline from western New York southwestward through western Pennsylvania, western West Virginia, Ohio, Kentucky, and Tennessee, where oil of high gravity is always secured. Of these States, Pennsylvania and West Virginia rank highest in the quality of their product. In West Virginia, the oil sands dip to a lower level than in any other locality in the Appalachian Geo-Syneline, the Pittsburgh Coal of the Pennsylvanian being only 50 ft. above sea level along the Nineveh Syneline at Wileyville, Wetzel County.² The very significant fact that the sands of the Mississippian and Upper Devonian Measures furnished the richest oil pools of the State along this

Jan 1, 1917