Search Documents

The Honor Roll includes the names of all members of the Institute Whom we know to have been on active military duty it the date of compilation, Mar. 5, 1919. Despite our efforts to have this list accurate and complete, some of our members who have been rendering military service are probably left off because of the fact that we have not been informed of their military connection. The list of men in military service has been compiled with great difficulty owing to the modesty of the members, who in their patriotism began their service but neglected to send us notice. In 1918, We published a separate Honor Roll of the Institute in which we included a list entitled "On active duty in other departments of the service" which contained the names of members who were rendering important emergency service to the Government other than in the Army. This list is entirely omitted this year because any list We might compile for this purpose would be entirely inadequate and must inevitably do injustice to a large number of our members who have been devoting great time and making many sacrifices for the benefit of the government along lines not within our ken. It is not too much to say that almost all our membership in this country has been, more or less directly, doing its uttermost for the successful prosecu¬tion of the war. The active work of many of these members we are Well aware of, as is also the rest of the civilized world. Faithful and wholehearted efforts on the part of many other members we have not been informed of, so that any list would be both incomplete and unsatisfactory.

Jan 1, 1923

By Pope Yeatman

THE Committee on the Elimination of Waste in Industry, of the Federated American Engineering Societies, in its report says that "Waste in -industry is attributable to four causes: 1. Low production, caused by faulty management, of materials, plant, equipment, and men; 2. Interrupted production caused by idle materials, idle plants, and idle equipment; 3. Restricted production intentionally caused by ,owners, managers, or labor; 4. Lost production caused by ill-health, physical defects and industrial accidents. The committee sent out elaborate questionnaires, and in them divided the responsibility into Manage-ment, Labor, and Outside Contracts. These question-naires showed that in the different industries examined the responsibility of Management was from 50 to 80 per cent. and of Labor from 9 to 28 per cent. The percentage of responsibility that Management was held accountable for was much larger than any of us supposed. However, when this question is studied, we realize how necessary it is to select, in the first instance, suitable personnel, in the form of directors, managers, heads of departments, experts, etc. We would like to -believe that the percentage of responsibility of Management for waste in the mining business was less than that quoted above, but there are so many mining properties started up and operated by men of no experience in such lines, and there have been so many improvements in late years in mining and metallurgical methods not taken advantage of, that we can not believe that. the percentage will vary much from that already quoted. Quoting from a report approved by the Committee on Management of the American Society of Mechanical Engineers: Management is the art and science of preparing, organizing, and directing human effort applied to control the forces and util-ize the materials of nature for the benefit of man.

Jan 3, 1922

By F. H. Newell

Measurements of the amount of water flowing in many of the larger rivers of the west have been made by the United States Geological Survey, and by this means the daily discharges of these rivers have been computed for a period of over two years. These measurements have been confined mainly to that part of the country commonly known as the arid region, where the rainfall is insufficient for the needs of plants most useful to man, and the supply of water, not only for agriculture, but also for mining and all other purposes, falls below the demands made upon it. In such localities flowing water has a great value, for without it many industries are impossible. Experience has shown that in the western part of the United States, over an area a little less than two-fifths of the whole extent of the country, there are great bodies of fertile land enjoying a genial climate, and in every way adapted to the support of a large population, except in the one particular of water-supply. By utilizing the water available, portions of this rich land can be rendered valnable. In other words, the laud-values rest directly upon the prospects of a continuous artificial water-supply. The same is true of many mineral lands, which require for hydraulic mining, or for the supply of concentrating-works, stanip-mills, etc., a certain water-supply, and are impaired in value if this supply is inadequate or irregular. The pressure of this need upon the mining industry is not so widespread, or in the first instance so severe as upon agriculture; but as different regions become more thickly settled, and the two industries compete for a water-supply not sufficient for both, it, is probable that the miner will suffer. But he can snspend operations with less inconvenience than the farmer. Agricuitural land, if the watersupply is not continuous, becomes a desert; on the other hand, the profit of mining is greatly enhanced by the presence of agricultural

Jan 1, 1892

By J. E. Pollock

IN the oil-refining industry, steel comprises by far the greatest proportion of the materials used in construction work, but with an enormous number of alloy steels and nonferrous alloys available, and a greater knowledge of their properties and corrosion resistance; a substitu-tion first in the "hot spots" and then in locations of moderately severe corrosive conditions will be made as the greater expense can be justified. In new construction work, advantage is taken of the experience already gained and appropriate materials used, whether for high temperatures and pressures demanding additional strength or for corrosive conditions. The locations, however, where equipment in operation constantly requires replacement will soon become evident, as will the necessity for replacement in more resistant materials, if considerable down-time is to be avoided. In what direction and how far to go in the matter of alloys then becomes a question of the highest importance. Obviously, any replace-ment with more costly material must be. justified economically by the promise of longer life, thereby saving both material and installation costs besides the reduction of loss of production. Where the equipment is overcapacity and a regular schedule of cleaning periods is in force, the last item frequently must be ruled out and justification made on the basis of the first two only. Installation of material that will outlast the remainder of the equipment and have no recovery value must also be avoided; this is particularly important in temporary construction or in old equipment that will soon become obsolete.

Jan 1, 1935

By A. D. Hodges

In May, 1850, the first gold from the Comstock lode was discovered in the sands near the Carson river. It had been washed down by natural agencies, through Gold Caflon, from the decomposed rock of the ledge above. Within a few weeks, the precious metal was traced more than three miles in shallow deposits along the bed of the canon, from the river to the Devil's Gate-—a narrow, rocky cleft, notable to the teamsters of a later day chiefly as the place where " Uncle Jimmy Fair" collected high tolls, and could not reduce the rates, because " this was all he had for the education of his poor children." From 1850 to 1857, a fluctuating band of miners, whose number varied from twenty to two hundred, washed the Gold Canon placers with rockers and long-toms, making four to five dollars a day each until the last-named year, when the deposits were in great measure exhausted. The chief settlement of these miners was at Johntown. During only a third of the year was the water-supply sufficient for their work. The remainder of the time they utilized in desultory prospecting of the hills and in occasional forays for supplies among the Mormons in Carson valley. In 1857, the Grosch brothers discovered the Comstock lode at some point, now unknown, in Gold Hill, but their discovery perished with them. Early in 1858, the " Pioneer Quartz Company," having located several of the small surface-veins around Silver City (whose connection with the main lode has never been definitely shown), built an arrastra, and worked some of their ore; but the returns were so small that they soon abandoned this business. The following winter, James Finney and his partners found gold in place in

Jan 1, 1891

By B. Y. Ekber, A. S. Gorbachev

The development of economically effective and safe methods of mining thick coal seams allow considerable coal reserves to be used as an energy resource all over the world.

Jan 1, 1979

By H. W. Miller, V. H. Wilhem

Although the year 1933 was a period of uncertainty, considerable new development was initiated, with a high percentage of favorable results, for owing to financial conditions only projects of merit were proposed and developed. Unfavorable marketing conditions caused severe financial losses to refinery and sales departments of nearly all companies during the first half of the year. In anticipation of stabilized Government control, earnings were generally favorable during the third quarter but failure of the Government to take legal action against violators of the proration orders, and lack of agreement on a definite plan of curtailment, resulted in considerable overproduction and demoralization of the market structure during most of the final quarter. However, toward the close of the year Government action against violators of the Oil Code had a tendency to decrease overproduction materially and give the market a firmer tone. As a whole, the price structure of crude oil was maintained at a high level during the year; in fact, at a much higher level than the price of refinery products warranted. At no time during the year was production within 10,000 bbl. daily of the state allotment, overproduction of crude reaching a peak of 70,000 bbl. on Sept. 7, average daily average for the year being about 27,000 barrels. Numerous plans for equitable curtailment were prepared and tested during the year, none of which fully solved the many and intricate problems faced by operators who were in most cases willing to curtail if they could feel that cooperation was being practiced by their neighbors. Outstanding events in California oildom during the period under discussion may be classified under the following headings: 1. New discoveries. (a) New development in proven areas. (b) Deeper zones in settled pools. 2. Unproductive wildcat operations. 3. Whipstocking practice and procedure. 4. Progress of unit and orderly plans of development.

Jan 1, 1934

By R. E. Grace, H. W. Schadler

DARKEN1 has established the theoretical relation between the self-diffusion coefficients and the Boltzmann-MatanO Or interdiffusion coefficient: D is the Boltzmann-Matano or interdiffusion coef-

Jan 1, 1960

By William A. Kapp

INTRODUCTION Coal is being mined from beneath residential areas, structures, bodies of water and other surface features in the coalfields to the north, south and west of Sydney. The particular problems faced by mine operators in these areas vary considerably due to differences in the overlying strata, the variation in the depths of cover and also depend on the number of seams being mined. Detailed subsidence work first commenced in the Southern Coalfield in 1965 and is now being carried out over areas of extraction at roost collieries. The analysis of the results of the early investigations and of the work which continues in other areas has shown that there is a consistent relationship between subsidence and mine geometry and has led to a reliable empirical method for the prediction of subsidence. In addition, particular aspects of each of the studies in the Southern Coalfield results in a clearer understanding of strata movements and of the resulting subsidence. The features of a subsidence trough apply generally to all areas but the magnitudes of specific features vary according to the stratigraphy of the particular coalfield. The aim of the subsidence work is to quantify the effects of subsidence for a range of mining geometries and mining conditions to enable the maximum safe recovery of coal from beneath surface features. The importance of local subsidence investigations is becoming more evident to mine operators and to authorities or organisations with surface interests. The subsidence work also provides important information on the stabilities of pillars of coal which remain unmined between panels of extracted coal. These pillars are not extracted either because of poor mining or geological conditions, or because pillar extraction is not part of the particular mining operation. Subsidence studies over these coal pillars clearly establish whether the pillars have remained stable or have failed to support the overlying strata. With subsidence studies continuing over several years, it is possible to assess the stabilities of these pillars on a long term basis. BACKGROUND TO THE STUDY OF SUBSIDENCE Geographical setting Most of the black coal production in Australia comes from the Sydney Basin. The coal seams extend for approximately 350 km along the coast of New South Wales and inland for distances up to 150 km. The City of Sydney is located near the centre of the coastal extent of the Basin where coal has been mined at a depth of 900 m. The Sydney Basin is part of the Main Coal Province of NSW and is divided into several coal- fields. The Southern Coalfield to the south of Sydney contained 15 operating mines and produced 12.7 million tonnes of raw coal during the 12 months to June 1981. The collieries discussed later are shown in Fig. 1. The prominent topographical feature of the area is the Illawarra Escarpment which rises to 400 m above sea level, or 300 m above the coastal strip along the South Pacific Ocean. The escarpment is mainly sand- stone and the weathering of the cliff line has resulted in a covering of talus material at its base. Several collieries are located near the seams which outcrop along the escarpment. The city of Wollongong is located in a scenically attractive area on the coastal plain. The suburbs of Wollongong extend north along the coastline, south to beyond Lake Illawarra and west to the lower slopes of the escarpment. The Illawarra Escarpment forms the eastern boundary of the Woronora Plateau. On a regional scale the surface dips gently to the west and thus forms a watershed for the rivers, most of which flow in a general north westerly direction, sometimes forming steep gorges in the sandstone. These rivers join the Nepean and Hawkesbury River system and flow into the Pacific Ocean north of Sydney. Seven dam have been constructed over the Southern Coalfield (Fig. 1) and with one large dam further to the west, their stored waters provide the needs of the Cities of Sydney and Wollongong and the surrounding districts. A large part of the area affected by mining is the undeveloped bushland of the associated catchment areas. In general no special precautions have been required with respect to subsidence with the exception of the dam structures and stored waters. With the increase in coal mining activities and the expanding residential development south of the City of Campbelltown in the outer Sydney Metropolitan area, subsidence is becoming an increasingly important area of research. Structures which have been affected or considered are townships and extensive residential areas, buildings of historical importance, major tollways, and a high pressure natural gas pipeline. The subsidence effects of mining beneath natural features within national parks is coming under study as mining approaches these areas. Geological setting The coal seams of the Southern Coalfield lie within the Illawarra Coal Measures. They contain high rank coking coal used in the local steel industry and for export. The Bulli Seam is mined extensively through- out the Southern Coalfield with the lower Wongawilli Seam being second in importance with regard to coal production. The top of the Bulli Seam is taken to be the marker horizon between the Permian Coal Measures

Jan 1, 1982

By S. B. Lement

THE nature of the carbides that form during the tempering of martensite is a subject of continuing controversy. The only direct methods of identification available are X-ray and electron diffraction. These methods are subject to several difficulties. Only a relatively few diffraction lines of appreciable intensity emanate from carbide phases that are formed at low tempering temperatures. Furthermore, some overlapping of carbide and matrix lines occurs. There is also the problem that numerous lines in the patterns of possible carbide phases that may be present have about the same d-spacings. Increasing the number of carbide lines and eliminating the matrix lines can be accomplished by extraction techniques. However, there is always the possibility that a change in carbide structure will occur as a result of removal from the parent matrix. Therefore, such techniques as electrolytic extraction and making extraction replicas should be checked by other methods. For identifying small amounts of carbide in a tempered martensitic matrix, electron diffraction carried out in reflection is more advantageous than X-ray diffraction. To properly prepare a specimen for reflection electron diffraction, an etchant that will selectively attack the matrix and thereby cause the carbide particles to stand in relief should be used. With an electron beam directed at a grazing angle to the specimen surface, the major contribution

Jan 1, 1960

By Graham Bright

THE rapid increase in reliability, the low cost f operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the' motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made.

Jan 9, 1921

By James F. Lewis

THE hematite iron ore mines east of the Hudson River are confined to a strip of country ten to fifteen miles wide, commencing on the south, near Fishkill, running northeast through Dutchess County, and striking the southeast corner of Columbia County, extending into Litchfield County, Conn., known there as the Salisbury mines, cropping out again at and near West Stockbridge, Lanesboro, and Cheshire, Mass., also in Bennington County, Vermont. The ores are found in beds or deposits and in veins, with a limestone ledge on one side and slate on the other, from six to thirty feet from the surface. Portions of it are quite solid, called rock ore, but

Jan 1, 1877

By W. A. Oates, J. S. Blakemore, E. O. Hall

AS part of an investigation into the effect of hydrogen on the serrated yielding of Ni-Cu alloys,' it was necessary to determine the solubility of hydrogen in the alloys of interest. With the exception of the work by Fukusima and Mitui2 who investigated the solubility of hydrogen in solid Ni-Cu alloys at 20 wt pct intervals at 1050°, 700°, and 350°C, the information in the literature is limited.3-10 Alloys were prepared from deoxidized Analar Copper and Mond Nickel pellets.' Wire samples were hydrogenated at 7.8 atm in an autoclave consisting of 5 ft of thick-walled Inconel 600 tube with a resistance furnace around the middle portion. The top end, at room temperature, was fitted with a safety valve, a calibrated pressure gage, and a sample inlet, while the bottom end, again at room temperature, was filled with water. After reaching equilibrium samples were quenched by dropping from the high-temperature region of the autoclave into water. They were then quickly transferred to liquid nitrogen where they were stored until analyzed for hydrogen using an Exhalograph.11 The results, which are shown in Fig. 1, represent the mean of two separate determinations on each sample. Because of the lower level of hydrogen at the high copper end of the series, the results here are of poor precision using this method. Fortunately, the results of Himmler9 using the Sieverts technique are available for these copper-rich alloys (>80 at. pct Cu)

Jan 1, 1969

By L. E. Wemple

Previous to 1915, zinc refining had not become a general practice among the zinc smelters in the United States. Such refining as had been carried on was confined chiefly to remelting very high-leaded zinc, such as third-draw metal from the retort furnaces, and slab dross, and hard spelter from galvanizing pots. In this remelting operation, the lead and iron were settled out and the refined spelter obtained graded fifth class, ie., Prime Western. Owing to the presence of lead in most zinc ores, the bulk of the spelter produced by direct smelting is of this Prime Western grade. Careful selection of ores of low lead content gave purer grades of spelter, z.e., Brass Special and Intermediate; and smelters which could secure ores carrying practically no lead produced high-grade spelter. Thus, in general, the grade of spelter produced by any smelter was predetermined by the purity of the ore it could obtain. The needs of the warring nations of Europe for enormous quantities of cartridge and other high-grade brass resulted in such a demand for the purer grades of spelter that the available supply of lead-free and low-lead ores could not produce the quantity required. Prime Western grades went begging, so to speak, while high grades sold at times from 5 to 15 c. per pound over the Prime Western market. The great demand, coupled with the wide market margin, which permitted the inherent costs and losses, resulted in the conversion of the lower grades into higher grades by processes of refining. These conditions also accentuated the development and size of the electrolytic plants, which were being worked out at the time this increased demand for pure grade of metal occurred. The electrolytic process, where available, produces a higher grade of spelter from impure ores than does the fire process; a large portion of those impurities in the ore, which by the distillation process would be carried into the spelter, are removed in the leaching of the ores and the purification of the solutions. The refining process, adopted at a number of smelters for the purpose of converting low-grade spelter into grades suitable for bras4 was that of redistillation.

Jan 1, 1918

By J. D. McClung

INTRODUCTION The ever increasing demand for coal sues that meet exacting specifications has made necessary the installation of thousands of dollars worth of crushing equipment by the coal industry. At one time the operator at- tempted to recover as much lump as possible but today he is confronted with the necessity of crushing to facilitate the mechanical cleaning process and to meet the demand for a variety of uniform sizes. As a matter of fact, about 65 percent of the coal mined in the United States today goes through preparation plants where it is crushed and cleaned. One becomes more aware of the importance of the art of comminution when it is realized that practically all of the operations in mining are involved in comminution in one way or another. Whether the coal is mined conventionally or by continuous miners it is separated from the solid by a breaking, ripping or milling action which essentially amounts to a comminution operation. Even degradation resulting from material handling from the mine working face to the preparation plant might in a broad sense be so classified, Then of course crushing is usually necessary in the plant before the coal is ready to be marketed. THEORY Despite the various comminution operations there is a lack of satisfac- tory information concerning the fundamentals of crushing and their relation to the variable factors associated with the operation. There are certain laws and theories on mechanical reduction, such as those of Rittinger, Kick and Bond that are helpful and useful. The difficulty in developing exact mathematical relationships for specific crusher applications is due to the many variable physical characteristics found in coal. Hardness, as measured by the Hardgrove grindability index, is one parameter that has been used for years to determine the resistance of coal to comminution. While the coal properties as measured by grindability are complex, recent work has shown that a high correlation exists between the grindability of some coals and their petrographic analysis. Early research on the hardness of petrographic entities from an Illinois coal2 demonstrated that durain was the hardest constituent followed by clarain, vitrain and very soft fusain. Other research demonstrated that, for different size fractions of the same coal, a wide variation in hardness commonly exists. For example, the fines in about half of 39 coals studied were softer than their corresponding coarse sues while most of the remaining coals were uniformly hard in all sizes. A few coals contained fines which were harder than their coarser constituents. These variations in hardness give insight into the heterogeneous nature of coal.

Jan 1, 1968

By W. M. Weigel

THE rapid advance, during recent years, in the manufacture of articles that have been in common use for generations and the development of new materials entering into appliances and devices unheard of fifty years ago, have created a demand for some of the more common non-metallic minerals. To supply this demand there has quietly developed a branch of the mining industry of which little is known by most mining engineers the mineral-filler industry. In this paper, and generally in the trade, the term mineral filler is applied to a mineral used, in its natural state after mechanical preparation only (such as. grinding, milling and washing), without undergoing any chemical change and without exerting any chemical action on the substance with which it is incorporated. The consumption of mineral fillers is confined chiefly to large manufacturing centers in the eastern and northern states. Where available, materials originating near the place of consumption are used, as most fillers bring a comparatively low price and, frequently, the freight may equal the cost of the finished filler at the mine. The southern states have abundant deposits of non-metallic minerals suitable for fillers, which supply the manufacturing industries in adjacent states. Many of these deposits are equal to, or superior, in quality to those mined in the north, but they can not compete with them because of the freight rates. The mineral-filler industry has felt the present depression, but it has suffered less than most mining industries for as a rule the mills are simple, the overhead expenses are low, and the labor is entirely local and can revert to farm work when the plant closes down. Many other deposits in the southern district will undoubtedly be developed when business. revives and freight rates are adjusted.

Jan 2, 1922

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

By G. H. Clevenger

THE reagents now used in flotation consist of various acids or salts, which may be either electrolytes or non-electrolytes, dissolved in water and some substance or combination of substances which function as collecting or frothing agents. At times the only dissolved salts present are those naturally occurring in the water used. The general effect of the electrolyte is to greatly sharpen the separation between the gangue and the concentrate. Examples of this are: The use of sulphuric acid with zinc ores; and of sodium carbonate or calcium oxide (line) with silver-gold ores. Crude pyroligneous acid is also sometimes used when available. Various oxidizing agents, such as permanganates, bichromates, etc., are added in the selective flotation of lead-zinc ores. Many other reagents for performing certain specific functions, either real or imaginary, have been proposed, and a number of them have been tried upon a working scale. The wild orgy of experimentation which is now going on in flotation exceeds even that which followed the introduction of the Washoe process for the treatment of Comstock ores, when, among other things, sage-brush tea and tobacco juice were reagents added to the pans. Out of all this will, of course, eventually come a more or less standard practice for the treatment of each class of ore. Omitting a discussion of the functions of frothing and collecting agents, the reagents used in flotation for this purpose may be classified under five general heads: (1) Essential oils; (2) fixed or fatty oils;. (3) alcohols and their combinations with organic acids; (4) coal tar and its refined products; (5) petroleum and its refined products. A flotative agent of some kind is required in flotation as now practiced. A single reagent, as, for example, certain. of the essential oils, may perform the dual function of frothing and collecting agent, or a mixture of substances may be required.

Jan 9, 1916

By Robert Glass Cleland

THE DEATH of William E. Dodge occurred at a time when, all unwittingly, the company in which he had so long been the dominant factor was about to break with its old practices, its old traditions, its old interests, and transfer its major activities three fourths of the way across the continent and engage in an enterprise that differed almost as much from the original Phelps Dodge undertakings as the rough, arid mountains of the new region differed from the green hills and valleys of New England. To understand the effect of this transformation upon the fortunes of Phelps Dodge, one must change the setting of the present narrative from the familiar locale of the Atlantic seaboard to the land of "distance, silence, and solitude," that men called Arizona. In 1880 that Territory was one of the last frontiers of the Old West. To the Spaniards it had been a land of mystery and fable, the limit of the King's settlements, the far edge of the rim of Christendom. Through it Coronado; in a vain effort to find the fabulous Cities of Cibola, had led "the most brilliant company ever assembled in the Indies to go in search of new lands." Below its southern border, Father Kino, the "steel-thewed" Jesuit described by his

Jan 1, 1952

By F. N. Ward, E. H. Bailey

Camp and sample-site methods useful for determining about 0.5 to 16 ppm of mercury in soils and rocks have been devised to complement the analytical methods already widely used in geochemical prospecting. In the camp-site procedure the sample solution is obtained by digesting the finely powdered sample with hot nine-molar sulfuric acid and bromine, the latter generated in place. The solution is buffered at a pH of 4 and the mercury is extracted into a relatively small volume of an organic solvent. Estimations are made by comparing the color of the mercuric dithizonate extracted from the sample with that extracted from a standard. In the sample-site method the mercury is volatilized as the iodide and the latter is dissolved in a buffer solution from which the mercury dithizonate is extracted as in the camp-site method. The estimation is made by a similar comparison with standards or by comparing the color of the mercuric dithizonate with artificial standards prepared from Orange II, an azo dye. Except for the establishment of standards, the time required by an experienced analyst seldom exceeds 10 min for a camp-site determination and 5 min for a sample-site determination. Camp-site determinations are useful for commodity studies and intensive exploration programs; sample-site determinations are applicable to extensive and reconnaissance-type geochemical prospecting programs. The results obtained on samples taken along traverses above known mercury ore deposits in the California Coast Range and western Nevada demonstrate the usefulness of both methods in geochemical prospecting. The increasing use of the mercury content of soils, rocks, plants, or water in geochemical prospecting emphasizes the need for analytical methods which are sensitive and at the same time require a minimum of readily available equipment. Sensitive methods based on the absorption of ultraviolet light by mercury vapor are common in the literature31 12. Although none of these methods have been used to analyze the large number of samples required in geochemical prospecting, they could be extremely useful except for the expensive instrumentation usually required to make the methods quantitative Also, such methods are perhaps too sensitive for field use, especially around areas of possible contamination. Other methods involve the distillation of mercury from a relatively large sample and subsequent collection of the vapors in nitric acid6. The mercury is then estimated by titration with a suitable reagent such as thiocyanate. These methods are not trace methods because the actual amount of mercury measured is often as great as 50 to 100 milligrams. Also, such methods are unsuitable for geochemical prospecting because of the amount of equipment necessary and the time required. Still other methods involve colorimetry, and the sensitive reaction between dithizone and mercury (11).. is the basis for a number of reports on the determination of mercury in biological materials 5,7. Moreover, by the judicious use of solvent extraction and suitable complexing agents, the dithiaone method can be made almost specific for mercury. However, none of the dithizone methods have yet been applied to the determination of mercury in soils and rocks. In most colorimetric methods he sample solution

Jan 1, 1961