Search Documents

By Zay Jeffries

IMAGINE a spinning sphere of hot matter about 8000 miles in diameter, rushing through space at a velocity measured in miles per second, and you have a rough idea of what our earth is supposed to have been like about two to four billion years ago. By applying all of the science known to man and, more especially, by determining the velocity of earthquake waves at different depths, making comparisons with meteorites, studying densities, compressibility of rocks and the nature of surface rocks, a fairly definite conception of the general constitution of the earth has been obtained.1 The earth is supposed to have a central core rich in iron containing a substantial amount of nickel and small percentages of several other elements. The density of the core is assumed to be about ten times that of water and the diameter about 4200 miles. An intermediate shell of density about 4, and thickness of about 1800 miles, is sup- posed to consist of heavy rocks including sulfides, oxides, and silicates. The outer rock shell, probably about 100 miles thick and with a density around 2.8, is thought to be composed mostly of silicates, becoming in general more siliceous as the earth's surface is approached. NATURE'S SMELTING OPERATION Nature seems to have subjected the earth to a stupendous smelting operation, burying beyond reach much of the metal that man recovers in his smelting practices. We live on the surface of Nature's "slag dump" and must be content, for the near term, to recover for man's

Jan 1, 1953

By J. H. Frye, S. G. Holder, E. E. Stansbury

Internal friction studies on annealed and cold-worked pure silver and alloys of silver with 4.5 atomic pct each of Cd, Sn, and Sb are reported. Small amounts of cold work, introduced by stretching pure silver, decrease the internal friction; large amounts of cold work, by wire drawing, cause this decreased internal friction to rise. Results of severol anneoling histories on the room-temperature in-ternal friction indicate a rather complex recovery and recrystallization behavior. A rather system-atic alloy effect is observed for the elements of Period V-B in silver in both the annealed and cold-worked states. DURING recent years internal friction measurements at very small stress levels have been interpreted in terms of structural models and mechanisms occurring within the metal or alloy.These measurements have been made over wide ranges of frequency of vibration and of temperature. While the effects of impurities, alloying, and plastic deformation have been studied by numerous investigators, no investigations of the effect of a series of solutes related by their position in the Periodic Table on a given solvent seem to have been reported. The present paper reports internal friction measurements on silver and on certain silver-base solid solutions to determine the values of room-temperature internal friction associated with varying amounts of plastic deformation and after different annealing

Jan 1, 1957

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By James C. Word, R. M. McLouski

This paper will describe the development and application of large-scale integration techniques employed in the fabrication of a germanium multielement array. The array consists of 100 by 228 PNP bipolar transistors fabricated on 5 mi1 centers. Back-biased p-n junction techniques are used for electrical isolation of the individual elements. The end use of the array is a high resolution, large area IR sensor. The monolithic array is fabricated in 1 ohm-cm p-type germanium epitaxially deposited on 6 ohm-cm n-type substrate. Epitaxy was accomplished through the hydrogen reduction of germanium te trachloride. Di-borane was used as the dopant. Base regions are achieved by the diffusion of arsenic from doped oxide or arsine sources. Oxide-masking of the arsenic im-pzlvity was achieved by the chemical deposition of a boron doped glass. The emitter is formed by an aluminum alloy diffusion technique. Vacuum deposited aluminum is used for the emitter, interconnections, and for the contact and bonding pads. ALTHOUGH a great volume of literature pertaining to the development of large scale integration techniques (LSI) has been published for silicon and in particular silicon imaging applications,' to date only a small number of similar devices have been constructed using germanium technology.' Since the physical and chemical properties of germanium are vastly different from those of silicon, the fabrication technology for integrated structures in germanium is also different from that of silicon. In particular germanium does not possess a stable oxide as can be grown on silicon by heating in an oxidizing ambient for masking of dopants and passivation. This paper describes the application of germanium LSI techniques employed in the fabrication of a multielement infrared sensor array. The array is used in a high resolution, large area infrared sensor for operation in the 0.8- to 1.5-u spectral range. Back biased p-n junction techniques are used for electrical isolation of individual elements. Discrete germanium devices have been fabricated routinely for some time. However, mainly due to the lack of a suitable mask for selective doping and the high current leakages inherent in germanium p-n isolation, few monolithic germanium structures have been constructed. THE INFRARED MOSAIC A cross-sectional view of the array is shown in Fig. 1. The monolithic structure consists of 12,800 PNP transistor elements in a 100 by 128 matrix fab- ricated on 5 mil centers. The emitters of each line of transistors are connected together using aluminum interconnects while the strip collectors are connected together in series at right angles to the emitter lines. The selection of this structure is dictated by the readout technique involved. Access to each element transistor is obtained by applying a bias voltage to a particular collector strip and separately interrogating each emitter row. A charge storage, i.e., an integration mode is used for reading out this particular array Construction techniques available for use with germanium do not include a selective p-type diffusion capability for surface concentrations greater than 10" per cu cm and junction depths greater than about 10 u. This fact limits the type of structure that may be used. Therefore, an array of PNP transistors that did not employ p-type diffusions was chosen. The structure was fabricated by growing a 1 ohm-cm p-type epitaxial layer on a carefully prepared 6 ohm-cm n-type substrate. N-type dopants were used for the isolation and base diffusions and alloyed aluminum was used to form the emitter junctions. The array was then completed by evaporation of aluminum interconnections and contact pads. SUBSTRATE AND SUBSTRATE PREPARATION Germanium substrates of (111) orientation grown by both Czochralski and zone leveling techniques were utilized for mosaic fabrication. Czochralski substrates were preferred because of the lower dislocation densities available in this type of material. Dislocation densities for the Czochralski material were typically less than 3000 per sq cm, while those for the zone leveled material were typically less than 5000 per sq cm. All substrates were uncompensated to minimize thermal conversion problems in subsequent epitaxial and diffusion processing. Both in-house and vendor polished wafers were used. The in-house polishing technique employed consisted of an initial gross chemical etch in CP4 to remove saw damage from both surfaces. This was followed by a chemical-mechanical polishing operation of one side of the wafer. The chemical-mechanical polishing solution used was Lustrox 1000 (Tizon Chemical Co.), and consists of zirconium dioxide, sodium hypochlorite, water and a surfactant. The wafer thickness before and after polishing was typically 0.020 and 0.010 in, respectively. THERMAL CONVERSION The problem of thermal conversion of both the substrate and epitaxial layer was particularly acute because of the relatively low carrier concentrations employed in both regions. This problem has been encountered by other workers in the past.3 Without special treatment before epitaxial growth substrate conversion (n-type to p-type) and changes in the re-

Jan 1, 1970

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965

By E. N. Mazza, H. S. Kalish

The effect of sintering types 302, 3028, and 430 stainless steel powder compacts in hydrogen and dissociated ammonia was investigated. It was found that sintering in dissociated ammonia resulted in as much as 0.5 wt pct increase in the nitrogen content of stainless steel even though the dissociation of the gas was complete. Sintering in hydrogen, on the other hand, reduced the nitrogen content of the stainless steel to less than 0.01 wt pct. In the case of the 302-type stainless steel, the low nitrogen content resulted in a material that was largely ferritic, whereas the high nitrogen content rendered the material fully austenitic. Sintering in dissociated ammonia resulted in lower density, generally lower tensile strength, less ductility, and higher hardness than sintering under equivalent conditions in hydrogen. The reduction of oxides on both stainless steel and iron particles was found to be effected by hydrogen partial pressure in the sintering atmosphere. Compacting pressure was found also to effect oxide reduction during sintering. DISSOCIATED ammonia often is used as a substitute'.' for hydrogen in sintering and in annealing, since economic advantages sometimes can be obtained by such a substitution. In addition, anhydrous ammonia contains very little impurity. Thus, dissociated ammonia gas is very dry whereas tank hydrogen often must be freed of oxygen and water vapor prior to use in many applications. The sintering of stainless steel powder compacts as well as bright annealing is well recognized as requiring a hydrogen atmosphere and for the foregoing reasons dissociated ammonia is frequently substituted. It has generally been overlooked, however, that the nitrogen in dissociated ammonia might have an important effect on the sintering process and on the properties of stainless steel compacts. Considered an inert gas in many applications, nitrogen, on the other hand, is very reactive with cer- tain metals. Dissociated ammonia could not be used for hydriding zirconium or titanium. Nitrogen reacts with columbium, tantalum, chromium, uranium, thorium, and many other active metals. Iron and iron-base alloys are, for the most part, inert in nitrogen but there are many borderline cases. It has been reported that stainless steel stabilized with columbium or titanium should not be sintered in dissociated ammonia.3 olybdenum has been reported as reacting with dissociated ammonia to a minor extent.' Although most of the reactions with iron-base alloys are attributed to the action of un-dissociated ammonia and the action of nascent nitrogen, Uhlig4 showed how readily pure molecular nitrogen reacts with and diffuses into 18-8 stainless steel at 1150°C. He also pointed out how readily nitrogen diffuses out of 18-8 stainless steel when heated in pure dry hydrogen, and these thorough investigations on the subject show that commercial stainless steels are nitrogen-bearing, since they are melted in air. The effects of nitrogen in stainless steel, particularly the 18-8 Cr-Ni type, previously have received considerable attention." In 1926, it was pointed out

Jan 1, 1956

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By H. J. Struth

A glance into the immediate future of the refining industry, and a retrospective view of 1929, cannot fail to emphasize the need for effective measures of control of refinery still runs. With oil producers alert to the need for control of the crude supply, it has become more than ever necessary for refiners to complete the movement toward stabilization by concerted determination to maintain still run schedules within the limitations prescribed by the demand for gasoline. The outlook for continued growth in the demand for gasoline appears to be well sustained by a preliminary survey of requirements for 1930. In fact, it is apparent that the industry will be assured of a market for gasoline that will aggregate in volume at least 472,000,000 bbl. this year. This indicates a gain in total demand over 1929 of about 9 per cent. or about 4.6 per cent, less than the gain recorded during 1929 over 1928, which amounted to 13.6 per cent. Despite the indicated increase in gasoline demand this year, it is apparent that little, if any, more crude will be required than last year. This is shown in Table 1, presenting estimates of gasoline demand and probable crude requirements for 1930. Table 1.—Preliminary Survey of 1930 Gasoline and Crude Run Requirements Millions of Barrels Doniestic gasoline demand................................... 397 Foreign gasoline demand..................................... 75 Total indicated demand...................................... 472 Natural gasoline content..................................... 53 Net gasoline from crude...................................... 419 Imported gasoline........................................... 13 Net gasoline required from refineries.......................... 406 Indicated excess stock Dec. 31, 1929........................... 10 Maximum protluction required................................ 396" At 40 per cent. gasolitlc recovery, this represents a maximum crude converson of 990,000,000 bbl., or a daily average for the ycar 2,712,000 barrels. Year after year, the refining branch of the petroleum industry has been found guilty of running crude to stills greatly in excess of normal requirements, causing frequent periods of market depression. A review

Jan 1, 1930

By Anthony Folger, Charles E. Straub

Kansas produced 38,150,878 bbl. of oil in 1928 and 40,658,170 bbl. in 1929, thereby retaining its rank as fourth among the oil-producing states of this country. Production for 1928 was less than that for 1927 (Fig. 1) because of a decrease in the number of completions, but the average initial production per well (Table 1) shows an increase due to the completion of wells of comparatively large capacity in the new Valley Center pool of Sedgwick County. This increase in average initial production per well was further augmented during 1929 by completion of additional wells of comparatively large capacity in the Valley Center pool and the new Greenwich pool of Sedgwick County. Production for 1929 exceeded that for 1928 and threatened to exceed all records except that of 1918, however, production was prorated in

Jan 1, 1930

By C. D. King

The advances in basic open-hearth practice which have occurred during the past decade have been principally in the direction of the physical development of larger units, decreased fuel consumption and increased length of furnace campaigns. However gratifying the economies which have resulted from these improvements are, it must be granted that like advances in chemical, physical-chemical and metallurgical knowledge pertaining to open-hearth practice would have added greatly to these already attained reductions in costs and it is the purpose of this paper to stimulate the discussion and study of these phases of cooperation and their relation to ingot yields. Definition and Calculation oF Losses In discussing basic open-hearth yields, the writer refers to the ingot yields obtained in the process of converting pig iron, scrap and ore to steel. In this conversion some scrap is produced. The difference between the total weight of ingots and scrap produced and the original metallic charge constitutes the loss. Basic open-hearth yields vary considerably, and while some of the divergencies can be explained metal-lurgically because of differences in slag analysis, proportion of pig charges, and character of steel made, there often remain differences that apparently do not readily disclose themselves. In reconciling yields by the usual accepted methods of calculation, one is often forced to evaluate large losses as ((unaccounted for." Such a system is prone to accept these large losses as inherent to the operat.ion and not, susceptible of appraisement and correction. It is obvious that if the ingot yield plus the scrap recovered subtracted from 100 per cent. determines the loss, a drop in yield may increase the loss or the scrap, and both contribute to a monetary loss. To be sure, one can subdivide these unaccounted for losses into various components, such as metallics in slag, free Fe in slag, spillage, etc., and thereby reduce the amount of losses considered as "unaccounted for." If empirical methods could indicate with some degree of accuracy all losses, however slight, the undetermined losses become appreciably smaller and resultant calculations will check actual

Jan 1, 1929

By A. B. Young

In the original design of the flue system, the flues from the roasters delivered their gases to a large brick dust chamber which discharged into another flue with stack connection, as shown in Fig. 1. The treater is so situated that the gases are taken by it directly from the chamber and discharged again into the flue. The complete installation comprises two treater units, only one of which has been installed at present. The treater is essentially a flue 1.0 ft. high, 12 ft. wide, and 61 ft. long. (3 by 3.6 by 18.5 m.). Suspended inside, vertically and running lengthwise, are four banks of No. 20 corrugated iron plates; each bank is 10 ft. long, making an effective treater length of 40 ft. The spacing from center to center of the rows of plat,es is 9 1/8 in. (23 cm.) giving six-

Jan 1, 1921

By H. W. Gudenau, R. S. Chatty, W. Wenzel, M. Ponthenkandath

During several experimental programs conducted at the Institute of Ferrous Metallurgy, Technical University, Aachen, whisker formation was observed when iron ores were reduced at low as well as at high temperatures. Thus, in an attempt to find the reason for the volume change taking place during reduction, iron whisker growth was observed. Whisker growth appears to be one of the important reasons for the swelling of pellets. One set of experimental observations determined that when iron forms as needles rather than as a crust on the surface of oxide, the pellets became very porous. In related experiments, the beneficiation of finely disseminated iron ores, in which the metallic iron is separated from the gangue in granular or nodular form, was achieved by a reduction-concentration method. In this process, which is conducted at sufficiently high temperatures, oxide whisker growth, resulting from the formation of volatile suboxides and a gas transport mechanism, plays a vital role in the joint deposition of SiO, and iron from the vapor stage.

Jan 1, 1973

By B. Woyski

MANY writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deoxidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gases is more difficult to overcome. The regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes are the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer' lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere.

Jan 5, 1922

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

By G. S. Hume

TuRneR Valley, on the eastern edge of the foothills of Alberta, 35 miles southwest of Calgary, continues to be the major oil field in Canada. This field began production of gas and naphtha from the Mississipian (Madison) limestone in 1924, and until 1936 all wells were drilled for these products. At the end of 1938 there were 104 gas wells. In 1936 proof was found of a crude oil zone in the same horizon but lower on the west flank of the structure, which is a large fold cut off on the east side by an overthrust fault of great displacement. Since 1936 drilling has been done for the development of crude oil and at the end of 1938 there were 64 crude oil wells. On test through a 1-in. choke these flowed at the rate of 50,000 to 60,000 bbl. a day, but on production would not be expected to make this volume. The output has been prorated according to the capacity of the Prairie market. During the harvest season, when the demand for oil and oil products was at its maximum, the allowable production of Turner Valley was 28,363 bbl. per day. With the arrival of winter, this was cut to 11,500 bbl. per day but later was raised to 12,500 bbl. Production in 1937 from Turner Valley was 2,767,221 bbl., which was more than double that of the previous year. Production in 1938 was 6,691,075 bbl., which is considerably more than double that of 1937.

Jan 1, 1939

By G. S. Hume

TuRneR Valley, on the eastern edge of the foothills of Alberta, 35 miles southwest of Calgary, continues to be the major oil field in Canada. This field began production of gas and naphtha from the Mississipian (Madison) limestone in 1924, and until 1936 all wells were drilled for these products. At the end of 1938 there were 104 gas wells. In 1936 proof was found of a crude oil zone in the same horizon but lower on the west flank of the structure, which is a large fold cut off on the east side by an overthrust fault of great displacement. Since 1936 drilling has been done for the development of crude oil and at the end of 1938 there were 64 crude oil wells. On test through a 1-in. choke these flowed at the rate of 50,000 to 60,000 bbl. a day, but on production would not be expected to make this volume. The output has been prorated according to the capacity of the Prairie market. During the harvest season, when the demand for oil and oil products was at its maximum, the allowable production of Turner Valley was 28,363 bbl. per day. With the arrival of winter, this was cut to 11,500 bbl. per day but later was raised to 12,500 bbl. Production in 1937 from Turner Valley was 2,767,221 bbl., which was more than double that of the previous year. Production in 1938 was 6,691,075 bbl., which is considerably more than double that of 1937.

Jan 1, 1939

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory investigatorsstate of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which andare useful for predicting machine performance and give acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary canexplain commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted.'TheRittinger In its first form, as stated by P. R. Ritted.'tinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include the concept of surface energy; in this form it was precisely stated by A. M. Gaudin' as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended." According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported- hat support the theory in its first form by indicating that the new surface produced in different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work done on the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading, since it does not follow the regular breakage pattern of most materials but is regularrelativelybreakage harder to grind patternat the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory4 is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr /log 2." The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-l.V f a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The evaluation in terms of kw-hr per net ton of —200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of —200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1953

By C. M. Haight

THE mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts. The latter are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various types are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and enable the men at the tops of the shafts to sort out the required sizes and to have them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 2, 1926

By William F. Butler, Mo-Hung Che

DEVELOPMENT OF MONEY AND MONEY STANDARDS This chapter is concerned with the rise, and then the decline and fall, of gold and silver as monetary metals. As a first step in tracing the history of this process, it is necessary to consider the nature of money, and the manner in which different forms of money have developed over the centuries. The origins of money go back into deepest antiquity. Once men ceased to be pure nomads and entered into even a rudimentary form of society such as clans or tribes, money had to be invented The first step was barter as farmers or hunters swapped their surplus products for things produced by artisans such as shoes, clothing, and simple tools. But such barter trading is inconvenient even in primative societies It is difficult to match up buyer and seller at any point in time There are problems in arriving at viable and acceptable terms of exchange. The accumulation of savings-wealth-is complicated. No one can be sure that a pile of furs, or wheat, or certainly fish or game can be used in the future to trade for other goods or services. So even prehistoric man saw the need for money. There was a need first for something to serve as a medium of exchange This was an essential first step in the process of specialization-or the division of labor. A farmer, a hunter, or a shoemaker could only devote his full efforts to his trade if he could be sure that he could exchange his surplus production for the other things he needed for existence. This required a medium of exchange-a form of money which would be broadly acceptable. Money was needed for two other reasons Some system of market prices was essential to facilitate the exchange of goods and services. This required some form of common denominator-some standard of value-to govern the exchange process. And there was also need for something to serve as a store of value, a place to put any excess production (savings) with the assurance that it can be used in the future to acquire a general range of goods and services. As a result, money, in one form or another, developed at a very early state in civilization. Yet the centuries have been marked by a search for a form of money which will possess in full measure all of the attributes in money-a reliable and universally acceptable medium of exchange, standard of value, and store of value. -A wide variety of things have been used as money at one time or another: shells, beads, stones, feather, metals, and even the teeth of sharks and dogs. Some of these things were obviously of little or no practical value. They were used because people had confidence in their continued acceptance as a medium of exchange. As the world evolved and as trading ex-

Jan 1, 1976