Search Documents

By J. J. Mulligan, F. F. Colcord, E. F. Kern

The electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years, and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. Effect of Copper Content on Conductivity The first work was to determine the specific conductivity of silver nitrate and copper nitrate solutions. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was then determined. The plotted results are shown in Figs. 1 and 2. The effect of increasing quantities of silver and copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 5C g. per liter, as its effect is to increase greatly the conductivity in an approximate propor-

Jan 1, 1926

By Michael Tenenbaum

Selected characteristics of nonmetallic phases were determined in low-carbon sheet steels which had been produced by various refining; deoxidizing, and casting procedures. The results showed little influence of the refining process on the quantity, distribution, size, and character of the nonmetallic phases. The quantity of inclusions was governed by the deoxidation procedures. While the mode of casting influenced the internal structure and the pattern of inclusion distribution, it had little effect on the quantity of nonmetallics. The vast majority of inclusions were under 30 µ in diam, and there was little change in size distribution during hot and cold rolling. The composition and structure of the inclusions were expained an the basis of known equilibrium phase diagrams for the appropriate systems. Additional work is needed to explain some of the observations of this paper. HENRY Marion Howe's contributions to the metallurgical profession include his many writings, the wisdom that he imparted to his students, and the inspiration that he gave to the many scholars, teachers, and industrialists who knew him personally. It was Professor Howe's intimate colleague, Albert Sauveur,1 who, in the first Howe Memorial Lecture, could have been speaking for the metallurgist of our generation as well as his own when he wrote, "...how many of us on the point of going astray were called back to the right path by Howe's guiding torch?" More than a quarter of a century later, Francis Foley,2 one of the last in the Howe Lecture series who worked directly with the great man, delivered the ultimate tribute, "...truth, in its time is so hard to identify." While Professor Howe strove to be right, "he was content if he provoked the reader to take the next step along the path to greater knowledge." Like so many of my predecessors, I sought guidance for this lecture by referring to Professor Howe's two classic texts, Metallurgy of steel,3 and Metallography of Steel and Cast Iron: the former book interpreting the facts as he saw them near the start of his career, and the latter—published 26 years later—pointing to many fertile fields for metallurgical investigation. Those of us who harvest the fruits of Henry Marion Howe's contributions to the metallurgical profession now look with wonder at the tremendous legacy he has provided. It is rewarding to study his writings and to recognize the anticipation of such aspects of modern ferrous metallurgy as: 1) Direct reduction 2) Steelmaking reactions 3) The approaches and benefits of degassing 4) Solidification mechanisms 5) Habits and behavior of nonmetallic inclusions 6) Recrystallization phenomena 7) Slip and slip propagation 8) Dislocations 9) Discontinuous deformation 10) Microscopic and macroscopic segregation

Jan 1, 1970

By F. F. Colcord

THE electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years; and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the, composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. EFFECT OF COPPER CONTENT ON CONDUCTIVITY The first work, was to determine the specific conductivity of silver nitrate and copper nitrate solution. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was, then determined. The plotted results are shown in Fig. 1 and 2. The effect of increasing quantities of silver and, copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 50 g. per liter, as its

Jan 2, 1926

By J. V. Gluck

In the present paper," as in earlier publications, V1'2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge's method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel'~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term 'probable error' was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that 'it is neither an error nor probable' ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people's minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the 'probable error' which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~' of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburgh, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1923

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

By Stanley M. Moos, Richard Addison

Introduction The Pueblo Viejo gold-silver mine, located in the Dominican Republic, started production in early 1974 processing ores averaging 4 g/t gold and 20 g/t silver at a rate of 7.25 kt/d. The ore milled is a silicified siltstone with average work index of about 8 that occurs as an extensive oxide capping of a primary sulfide ore body. The sulfide ores are refractory to conventional treatment process and extensive research work is now in progress to develop a treatment process for them. The ore deposit has a long history, having been mined by the indigenous Arawak Indians for some time in the early sixteenth century prior to the arrival of the Spanish, and then by the Spaniards. In the early 1950s, Italian engineers attempted to process the sulfide ores. Mining by the Indians and Spanish was abandoned because of low grade and little coarse gold in the oxide ores and by the Italians because of the refractory nature of the sulfide ore. In 1969, Rosario Resources geologists discovered that there existed sufficient reserves of oxide ore for a viable mining operation and the plant was designed, built, and brought into production.

Jan 1, 1981

By T. H. Oxnam

INTRODUCTION. THE predominating value of the ores now being treated by the Palmarejo and Mexican Gold Fields, Ltd., is silver, although some gold is also carried. The present method of treatment consists of wet-crushing and concentrating, followed by the cyanidation of the unroasted sands and slimes. The sands are treated by leaching and the so-called accumulated slimes by a system of agitation and decantation. It is only within very recent years that the cyanidation of unroasted silver-ores has been commercially successful. In fact, at the time operations were begun at the cyanide-plant at Chinipas, February, 1902, I knew of no other leaching-plant treating similar ores successfully. The cyanide treatment of the Palmarejo ores differs but little from the ordinary practice in cyaniding gold-ores; and perhaps but little, if any, new information concerning the metallurgy of silver is to be gleaned from it. PALMAREJO MINE. The Palmarejo mines are located in the southwestern part of the State of Chihuahua, Mexico, on the foothills of the Sierra Madre mountains, at an elevation of 3,200 feet. The mills, 12. miles distant, are situated on the Chinipas river, near the town of Chinipas, which is about 150 miles northeast of Agiabampo, on the Gulf of California. Supplies are shipped via this port as this route is the best and most direct to the property. The ore-bodies in the Palmarejo mines have been deposited. along a series of rock-fractures, caused by an intrusion of eruptive rock. The most important of these fractures or fissures, both in width and value, are the Prieta and Blanca veins, which.

Jul 1, 1905

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By William H. Spice

For the year 1943, exploratory drilling in South Central Texas continued on the sharp decline that started during 1942. Of the 3 counties comprising this district, as now revised to include the same area as is covered by District No. I, Oil and Gas Division, Railroad Commission of Texas, I5 counties are producing oil or gas. Only 29 exploratory wells were drilled during 1943, as compared with 51 exploratory wells in 1942, or a decrease of over 40 per cent. One new oil field and one new gas field were discovered during the year and a new horizon was discovered in an existing oil field. This cornpares with two new oil fields and an extension to an existing gas field in 1942. The one new oil field, South Washburn, in southeastern La Salle County, was discovered by Quintana Petroleum Corporation's No. I-D South Texas indicate in April 1943, flowing 4 bbl. per day, 48" A.P.I. gravity oil with an estimated 4 million cubic feet of gas from Wilcox sand at 6030 ft. This well i's the result of an extensive seismograph survey of the area. It is about 434 miles southwest of the same company's Green Branch field and by the end of the year one dry hole had been drilled to the southwest of this discovery. The one new gas field, which was not named, was located in eastern McMullen County by Edwin M. Jones' No. 102 Ezzell, in November 1943, for an estimated 8 million cubic feet of gas from shallow Jackson sand at 1222 ft. NO addi- tional wells have been drilled in this area, which may also be considered as an extension to the South Calliham field. The one new producing horizon was discovered in the South Campana field in southeastern McMullen County, by Argo Oil Corporation's No. 2-G Edrington, in January 1943, flowing 55 bbl. per day, 21' A.P.I. gravity oil with 40 per cent water from Government wells sand at 2609 feet. None of these discoveries were of major importance and subsequent development in these new areas has proved to be disappointing. Produc'tion for the district during 1943 totaled approximately 6,985,000 bbl. from about 3430 producing wells. This is an increase in production of about 5 per cent over 1942, but a decrease in producing wells of about 10 per cent under the number of wells producing in 1942 for the same district. Average production per well was 5.4 bbl. during 1943 as against 4.8 bbl. during 1942. Approximately 5,320,000 hhl. of this total production, or 76 per cent, was produced by the four Edwards lime fields, Luling, Branyon, Salt Flat, and Darst Creek, which are from 22 to 14 years old. The remaining production came from the 43 other active oil fields in the district. Drilling in the proven fields maintained approximately the same level as for 1942, with a total of 36 wells drilled. Of these operations, 21 were oil wells, one was a gas well and 14 were dry holes. This is a slightly better proportion of producers than for 1942. Washburn field had the greatest number of new producing wells drilled during the year, with a total of 10.

Jan 1, 1944

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active'.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of' gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By Frederic K. Bunton

The smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due.to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at very hig~; efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of 81.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 Dons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by ALfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Worlrs, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913). II. Location and Connections The smelter of this company is about half a mile south of GreenGood, in the Boundary district of British Columbia, on the Columbia & Westerg branch of the Canadian Pacific Railway. It was originally built in 1900 by Paul Johnson, to handle 600 tons of ore a day in two small furnaces of 300 tons capacity; but in 1907 the old furnaces were torn out, the plant was remodeled, and three blast furnaces, 48 by 240 in. at) the tuyéres, were installed. In 1910, two of these were enlarged to 51 by

Jan 1, 1916

By W. L. Fink, L. A. Willey

DURING the war there was introduced a new higher strength aircraft alloy designated 75S.1,2.3 The properties of this alloy assure extensive applications in both military and commercial aircraft. It is therefore important to understand its limitations as well as advantages. The properties of 75S alloy in the heat-treated tempers, like those of many other aluminum alloys, are affected by the rate of quenching. In general, low quenching rates tend to cause low strengths and to adversely affect the resistance to corrosion. Commercial quenching procedures are usually sufficiently rapid to permit the development of maximum properties. However, in the center of heavy sections, such as large rolled and extruded shapes, the quenching rates may not be rapid enough to develop maximum strength or resistance to corrosion. The investigations of 75S alloy described herein reveal the most critical range of temperature and the effects of quenching sheet and extrusions at different rates through that temperature range, on the tensile properties and resistance to corrosion. PROCEDURE Preparation of Specimens Sheet specimens (3 in. by 9 in.) were prepared from a commercial lot of 75S "as rolled" sheet (0.064 in. thick). The composition° was as follows: Weight Percentage Cu Mn Mg Zn Cr Al with Normal Impurities 1.64 0.16 2.58 5.66 0.27 Remainder The specimens employed for the determination of the time-temperature relations during quenching of sheet were prepared by the following procedure: the hot junction of a 28-ga. iron-constantan thermoelement (asbestos insulated) was brazed to a thin strip of aluminum which was in turn brazed into the end of a 3/16 in. i.d. by ¼ -in. o.d. by 30 in. long aluminum protection tube. Before brazing, the tube was flattened to 0.064 in. thickness over the junction and adjacent lead wires for a distance of 1 ½ in. The flattened end of the tube was fitted into a slot cut from one edge to the center of the 3 in. by 9 in. by 0.064 in. sheet and brazed into place. The brazed joint was dressed to the thickness of the sheet and the entire specimen buffed to approximately the brightness of "as rolled" material. Because of the brazing operations required, these specimens were prepared using 3S alloy. For the investigation of quenching rates in heavy sections, there were used 75S extrusions which had compositions similar to that of the sheet. The specimens consisted of 14 in. lengths of ¾ in., 2 in., 3 in. and 4 in. diam cylindrical rods and a roughly rectangular extruded section which was approximately 4 in. by 7 ½ in. Thermocouples were peened into the bottoms of 1/8 in. diam wells drilled into one end and parallel to the axis to a depth of

Jan 1, 1947

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By F. C. Hull

The grain size of a metal or alloy is one of the most important factors determining its properties. In steels, for example, grain size affects hardenability, toughness and machinability; in brasses, grain size is related to hardness and deep-drawing quality. In the field of heat-resistant alloys, grain size has a marked effect on ductility, creep and endurance strength. In order to determine these effects, as well as to control the properties of materials, many accurate and rapid measurements of grain size must be made. This paper presents a new and improved method for the estimation of grain size. Usual Methods OF EvaluatiNg Grain Size A frequetly used method of estimating grain size is that of comparing the image of a polished and etched specimen on the ground-glass screen of a metallographic microscope with standard grain-size charts. Several types of standards are available for use with different classes of microstructures. Geometric Grids.—The Metals Handbook' has a series of hexagonal grids ranging in size from ASTM No. I to 8. Idealized Grain Networks.—Idealized grain.boundary networks for ASTM grain sizes I to 8 are included in the American Society for Testing Materials Tentative Standard E 19 - 39 T, standard Micrographs & Metals Handbook and ASTM Tentative Standard E19-3gT contain micrographs of hypo-eutectoid and hypereutectoid steels ranging in grain size from No. I to 8. The grain size of annealed brass (diameter of the average grain in millimeters) is obtained by comparison with 10 micrographs of varying. grain size in ASTM Tentative Standard E 2-39 T. A handicap to accurate evaluation of grain size by this method is the fact that it is difficult to compare photographs in a dimly lighted room with the image on the ground-glass screen, or, if the general illumination is increased so that the printed standards may be clearly seen, the contrast of the image of the unknown is decreased. It is easier to estimate grain size by comparing a micrograph of the unknown with the grain-size standards. However, photographing every specimen on which the grain size is desired is too costly in time and materials to be practicable. For hardened steels, the Shepherd or Jernkontoret fracture grain-size standards are very accurate and useful, but this method obviously cannot be applied to ductile alloys such as brass, stainless steels and austenitic heat-resistant alloys. Jeffries' method for grain-size measurements consists of counting the number

Jan 1, 1948

By R. Shuttleworth, R. Smith

A Knudsen effusion tnethod I~as been used lo measure the vapor pressure of pure iron in the temperature range 1000° to 1500°C. Neutron-irradiated , natural iron was used and the Mn'~proclzdced by the (n, p) reaction removed by evaporation at high temperature. The results can be represented by the equation: where pM - 1.088 x 107 atm and T, = 20,890°K. A value of 100.2 kcal per g- atom was obtained for AH;. THE vapor pressure of pure iron in the temperature range 1000" to 1500°C has been measured. Radioactive iron and a Knudsen cell technique were used and the Mn' produced by an (n, p) reaction removed by evaporation at high temperature. From the variation of vapor pressure with temperature values of the enthalpy and entropy of solid iron have been found. Previous workers2 used a Lang-muir method and measurements were made over a smaller temperature range than that in this work. EXPERIMENTAL The apparatus used was similar to that of Pyle and Shuttleworth, and McLellan and Shuttle worth. However, because of the higher temperatures the Knudsen cell was machined from tungsten bar and the flanged furnace tube was beryllia. Heating was by passing a high current (70 amp at 7 v for 1500°K) through a strip of tantalum foil laid across the top of the cell and through a turn of molybdenum wire around the furnace tube. This method of heating ensured that the top of the cell was slightly hotter than the base and prevented condensation and re-evaporation from the orifice. The temperature was measured by means of a pt/Pt 13 pct Rh thermocouple spot-welded to the base of the crucible. To ensure accurate temperature measurement the iron was in the form of a thin disc (0.75 cm diam by 0.075 cm) which lay on the base of the cell. The high-purity iron was irradiated in the Harwell pile for a week at a neutron flux of 1.2 X 10" neutrons per sq cm per sec. The isotopes fe'~ and Fe" are produced by (n! y) reactions but only Fe", half-life 45.1 days, is a emitter; Mn which is also a y emitter, half-life 300 days, is produced simultaneously by an (n,p) reaction.' Immediately after irradiation of natural iron the ratio of ~e" to Mn y activity was 100:l. However, manganese is very much more volatile than iron and almost all the y activity of the condensate is due to Mn'~. Thus it was essential to eliminate all the manganeses before any measurement of the vapor pressure of iron was made and this was done by preliminary heating for 20 hr at 1400°C. For each determination the iron was dissolved from the target with acid and the y activity compared to a known weight of iron. By means of a y-ray spectrometer the y-activity measurements were made at the 1.09-mev peak of the 17e5' spectrum where the background was of the order of 3 cpm. Despite the low specific activity of ~e" a mass of 10- " g of iron could be determined corresponding to a vapor pressure of about l0-'' atm. RESULTS The vapor pressures were calculated from the equation: Where m is the mass of iron effusing in a time t through an orifice of area a2, r is the radius of the target, Z is the distance from the orifice to the

Jan 1, 1965

By T. Busch, R. A. Dodd

The solubility of hydrogen in pure iron and pure nickel, and of nitrogen in pure iron, has been determined and agrees well with earlier data. Nitrogen is insoluble in pure nickel and cobalt. The solubility of nitrogen in Fe-Ni alloys also confirms earlier- work. The solubility of hydrogen in Fe-Ni alloys increases non-linearly with increase in nickel content, but the solubility of hydrogen in Ni-Co and Fe-Co alloys reaches a minimum at 75 and 50 at. pet, respectively. The solubility of nitrogen in Fe-Co alloys decreases approximately linearly with increase in. cobalt content. Nitrogen is insoluble in Ni-Co alloys. Determined interaction parameters are in good agreement with predictions of Gokcen and Ohlani. THE solubility of hydrogen and nitrogen in liquid iron and iron alloys has been studied by various investigators.'-l' The method of solubility measuremerit due to Sievertsl is usually preferred when the vapor pressures of the liquid components are sufficiently small, but other techniques such as sampling the equilibrated melt and then analyzing by vacuum fusion have been used quite often. Previously reported data on the solubility of hydrogen and nitrogen in ostensibly pure liquid iron are summarized in Table I; certain of the quoted results were obtained by interpolation of the published data. Agreement between the various investigators is only fair, indicative of the experimental difficulties involved in obtaining gas solubility data. The only report found on the solubility of hydrogen in pure nickel is that of Sieverts.2 The solubility of nitrogen in iron-nickel alloys has received some attention, 10, 11 the results indicating that the solubility decreases with increase in nickel content, becoming zero for pure nickel. There is no published information on the solubility of these gases in either pure cobalt or alloys containing cobalt EXPERIMENTAL PROCEDURE Sieverts' method of solubility measurement was used throughout the investigation. The construction of the melting chamber is somewhat different from A. Optical pyrometer F. Alundum cover B. Vycor chamber G. Alumina crucible C. Furnace coils H. Alundum sand D. Glass water jacket I . Alundum thimble E. Chamber support J . Detachable vycor base sealed with de Khotinsky cement

Jan 1, 1961