Search Documents

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By C. W. Wahsburne

Former studies of sedimentatry strata have been based upon the mineralogical and mechanical characters of the solid components, rather than upon the open spaces between them.

Jan 1, 1915

By R. C. Ku, A. J. McEvily, T. L. Johnson

AS reported in a recent paper,' we attempted to measure the response to stress of as-quenched Fe-Ni-C martensites (Ms of -35°C) in both the micro-and macrostrain regions. To avoid effects associated with the diffusion of carbon, tensile specimens were quenched from room temperature at 78°K and tested after 15 min in situ. It was assumed that the transformation had terminated and that the retained austenite was essentially stable. In the tensile tests microplastic strains of the order of 10"* were measured at stresses below 20 ksi. It was concluded that the observed strains were due to the motion of dislocations in the martensite, the dislocations having been introduced during transformation. It was argued that transformation or plastic deformation of the retained austenite did not contribute to the non-elastic deformation measured in the microstrain region. In contradiction to the above argument, Magee and paxton2 have more recently shown that the strain due to isothermal transformation of retained austenite to martensite can contribute to plastic deformation at low stresses even at 78°K. Moreover we were unaware (nost)-a culpa) of a paper by Machlin and cohen3 in which it was clearly shown by resistance measurements that isothermal transformation at 78°K leads to the formation of an additional 1 pct or so of martensite after the initial athermal transformation, even in the absence of external stress. We have verified Machlin and Cohen's results in the following manner. A capacitance microstrain gage was placed on a tensile specimen before immersion in liquid nitrogen. After 15 min at 78°K detectable burst phenomena had ceased and it was then possible to obtain a continuous record of the additional extensional strain due to spontaneous isotherma1 transformation. The results for the Fe-Ni-C series studied are shown in Fig. 1, and are similar to those of Machlin and Cohen who investigated a low-

Jan 1, 1968

By L. S. Reid, R. L. Hunntington

The study of the flow of oil and gas mixtures through oil-bearing formations has received special attention from the petroleum industry within the past few years, and has resulted in a series of research projects based upon various phases of the flow of heterogeneous fluids through porous media. Obviously, the low cost of producing oil during the flowing life of a well makes it desirable to obtain production by natural flow as long as possible and to effect a maximum recovery of oil and gas by the utilization of reservoir energy through efficient methods based upon a thorough knowledge of reservoir characteristics. Despite the extensive research that has been carried out, there is little information available on the behavior of oil and gas mixtures flowing through reservoir formations. This makes it impossible to predetermine the optimum operating conditions for flowing wells. A differential pressure must exist in the reservoir in order to induce flow toward the well. It is a well established fact that with homogeneous fluids the relation of pressure drop to linear distance traveled is a straight-line function as long as the flow is viscous. However, in regard to gas-saturated oils, a number of investigators1l,2,3 have reported that the flow characteristics are materially altered as some of the lighter hydrocarbons are liberated from the oil to form gas while the fluid passes through the reservoir. Most of the work done has been concerned primarily with steady-state flow of liquid-gas mixtures. Cloud1 has studied the effects of saturating crude petroleum oils with various gases, together with the resultant pressure gradients under steady flow conditions, noting that unsaturated oils flowed faster and yet maintained lower pressure gradients than saturated oils. The work of Wyckoff and Botset4 has constituted a major step in the interpretation of heterogeneous fluid flow; especially their concept of

Jan 1, 1938

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By G. B. Gould

EVERY mathematical statement of a measure of anything (as distin-guished from a count) is followed by a qualification always implied if not explicity stated--that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accu-racy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applica-tions-and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this ques-tion of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not, readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject them-selves. There is great need for more widespread understanding of what has been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments.

Jan 1, 1937

By J. Richard Lucas

The coal industry, one of the great basic industries in the nation, plays a major role in the American economy. Coal is the principal fuel used in generating tremendous quantities of low-cost power so necessary to the nation. Two-thirds of the electrical energy and one-fourth of all energy consumed in the nation is produced from coal. Large-scale production of steel, cement, and chemicals is vitally dependent upon this natural resource. Because of extensive reserves and low mining cost, it is one of the few natural resources in which the United States is a significant exporter. During 1965 in excess of 500 million tons of coal were produced, almost 10% over the previous year; more than 50 million tons were shipped to foreign markets. The utility market gained approximately 8% during the year for a total of 242 million tons.

Jan 2, 1966

By H. W. Reinhardt, J. W. Dally

A dynamic photoelastic analysis of stress waves interacting with a free surface is described. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb N,). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. The mechanics of rock breakage by means of explosives has received considerable treatment by many investigators including Duvall, Obert, Broberg, Rinehart, and Langefors1-11 over the past two decades. Indeed in more recent years several texts12-15 have been written on the topic, treating a wide variety of subjects which are logically related to the modern technique of rock blasting. In rock blasting the chemical energy of a concentrated explosive contained in a relatively small diameter borehole is utilized to fragment the rock. The explosive is transformed into a gas with enormous pressures which exceed 10-5 bars18 This high pressure shatters the rock in the area adjacent to the borehole and produces dilatational and distortional stress waves which propagate radially away from the borehole. The state of stress associated with these outgoing waves produces a system of cracks which extend for a few feet from the borehole. The breakage produced in this manner is limited as the dynamic stress in the pulse attenuates markedly with distance. In the absence of a free surface, the stress wave propagates away from the source without further fracture. With a free face of rock near the drill hole, another mode of breakage occurs which is due to scabbing failure of the layer of rock adjacent to the free face. These scabbing failures are produced by the reflection of the incident waves and the conversion of compressive stresses into tensile stresses sufficiently large to fracture the rock. The detailed nature of the interaction of the stress waves with the free surface is complex and difficult to treat analytically. However, dynamic photoelasticity offers an experimental approach which gives a fullfield visual display of propagating stress waves and the reflection process. Applications of static photoelasticity to solution of problems related to mining technology have become relatively common (see, for instance, Refs. 17 and 18) with a plastic model loaded to produce a state of stress representative of that occurring in the workings of a mine. The application of dynamic photoelasticity is ex tremely limited. Tandanand and Hartman19 have used a multiple spark camera to study fracture in glass and plastic plates impacted by a chisel-shaped tool. This paper describes a dynamic photoelastic analysis of stress waves interacting with a free surface. The free surface is that of a bench with a fixed bottom so common in quarry applications. The stress waves are generated by line charges of lead azide (Pb-N6). Four models of identical geometry are investigated with the direction of detonation of the line charge varied between the four models. Dynamic photoelastic patterns are recorded and analyzed to indicate which method of detonating the line charge produced the largest magnitude of tension at the free surface. Experimental Procedure The model illustrated in [Fig. 1] was fabricated from a sheet of Columbia Resin CR-39 to represent a bench with a fixed bottom. Properties of the CR-39 pertaining to these dynamic experiments are listed in [Table 1]. Scribe lines on 1-in. centers are used to identify locations along the bench face. The bench height was 8 in., the burden was 3 in., and the overall dimensions of the sheet, 16 and 18 in., were large enough to eliminate reflections from nonessential boundaries during the period of observation of the dynamic event. To simulate a charge in a borehole, a groove 0.062 in. wide and 0.080 in. deep groove was cut into the sheet from one side. The lower end of the groove was 1 in. or 1/3 the burden distance below the bottom of the bench. The upper end of the groove was 3 in. or one times the burden distance below the upper level of the bench. The groove was packed with 60 mg of Pb No per in. of length, and ignited with a bridge wire detonator. Four different ignition procedures were used to examine the effects of detonation direction on the stress wave interaction with the free face of the bench. In Test 1 the line charge was ignited at the top and the line charge detonated downward. In Test 2 the line charge was ignited at the bottom and the charge burned upward. In Test 3 the charge was ignited in the center with the top half burning upward and the bottom half burning downward. Finally in Test 4 the line charge was ignited at both ends simultaneously. Sixteen high-speed photographs of the photoelastic fringe patterns representing the stress wave propagation were recorded for each of the tests. A Cranz-Schardin multiple spark gap camera 20,21 was operated at framing rates which were systematically varied from 110,000 to 250,000 frames per sec during each test.

Jan 1, 1972

By A. J. Lyon, J. B. Johnson, Samuel Daniels

The wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating at 932' F. (500" C.) for 2 hr., cooling in air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that" considerable improvement in the mechanical properties of copper-aluminum alloys may be obtained from suitable heat treatment applied to castings."' Jeffries and Gibson8 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932" F. in a nitrate bath for 1 hr., quenching in fish oil, and reheating at 300' F. for for 1 hr. Their results disclosed the facts that the ultimate strength and the percentage of elongation of sound alloys were usually, and quite uniformly, improved by heat treatment; that with the iron content ranging between 0.36 and 0.88 per cent. and the silicon content between 0.24 and 0.60 per cent. the effect of increasing the copper content (Tables 10

Jan 1, 1925

By Carl Zapffe

The manganese ore reserves of Lake Superior, because of their location and nature, have recently achieved a rnarked degree of importance as compared with the world's manganese reserves. To appreciate fully the significance and the adequacy of this reserve, one should understand how such ores are used, where obtainable, the quantity used, possible avenues for increasing use or application, and the chemical and physical characteristics of the available ores. Only with those data at hand, is it possible to arrive at a convincing answer to the question whether the reserves of manganiferous iron ores are adequate to satisfy the annual demand of the presently known iron ores for the full life of the latter. That they should last is vital; and to ascertain whether they will last was the purpose of the present investigation, which marks the first attempt to study these Lake Superior reserves. The Lake Superior region possesses and supplies the full assortment of iron ores needed for the conversion of ore into pig iron and steel ingots and castings. These ores are named bessemer, low-phosphorus and high-phosphorus non-bessemer, manganiferous and siliceous; and to include the term aluminiferous would be in keeping with the most recent nomenclature adopted by some dealers. About 35 or 40 years ago, perhaps less, most of the Lake Superior ore which is being used today was the material then considered either useless or too poor for immediate use; perhaps it was considered no more than a future reserve. An examination of the analyses of ores and the guarantees in the sales of those older times convince one that the opinions of those days must have been governed by only small differences in analyses. Some grades of ores used today in substantial amounts were used most sparingly only one or two decades ago. The relative quantities of the different ores used are ever changing; and, bit by bit, the metallurgy and the opinions are ever changing and the prejudices against certain ores and practices decrease. This is unquestionably more pronounced for the manganiferous ores than for any other kind. If, when using the present data for manganiferous ores, we will only be content to make allowances for the same experiences other kinds of ores

Jan 1, 1927

By W. J. Reagan

The problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 max.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot after coming from the slicing lathe. Jusf sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By J. M. Stuart, G. D. Bengough, A. R. Lee

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By A. R. Lee, G. D. Bengough, J. M. Stuart

Corrosion tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply of oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case of salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion of the metal was shown in some experiments due to Friend.2 He tested the corrosion of mild steel plates immersed in water in glass jars, a steady stream of air being drawn over the surface of the water in the jars. The air passing through half the number of jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor." Conditions for Quantitative Corrosion Tests These results show that we must either control or prevent evaporation at the liquid surface, if we wish to avoid effects on the rate of cor-

Jan 1, 1929

By M. C. Miller, M. R. Tek, D. L. Katz

Previous studies have shown the influence of geometric variations on the drawdown and buildup behavior of a well completed in a homogeneous, porous medium containing a single-phase fluid. Other papers have shown the influence of leakage across caprocks on drawdown tests on water wells and aquifers. This paper presents two additional cases: the influence of an adjacent, expansible source of fluid, and the effect of caprock leakage on the measured in situ permeability and compressibility. Methods are developed for evaluating the influence of these two deviations from a uniform aquifer upon the in situ permeability and compre.ssibility indicated by pump tests. INTRODUCTION In relatively uniform porous media, saturated with a single-phase fluid, the effective reservoir permeability and compressibility of the water porous bed system may be obtained from drawdown and build-up data on wells, such as the initial wells drilled in aquifer storage reservoirs (Homers and Katz et al.7). In considering the drawdown and build-up behavior of wells adjacent to storage reservoirs, or of wells in an aquifer adjacent to an unknown gas field, questions arise as to the quantitative effect of the presence of compressible fluid on the measured permeability and compressibility of the formation. The solution to this problem is presented, using a constant pressure line source at some distance from two wells, one of which is pumped and the other used as the pressure observation well. The solution is presented in terms of the geometry of the wells and their relationship to the constant pressure line. It is known that caprock leakage can interfere with the determination of an aquifer in situ permeability and compressibility (Mantush4, Hantush and Jacob3 and Witherspoon and Muellerll). This paper presents an added case of the effect of leakage through a caprock of known thickness and permeability on well tests starting with a reservoir of constant pressure above the caprock and contributing to the aquifer as a result of the pump test. Again, both a pumping well and an observation well are postulated. These two cases are presented together since both a compressible fluid nearby and. caprock leakage show similar deviations from expected in situ permeability and compressibility results, and the solutions are similar in form. EFFECT OF A NEIGHBORING CONSTANT PRESSURE SOURCE ON IN SITU MEASUREMENTS Bixel, Larkin and van Poollenl presented a paper showing the influence of a discontinuity of the properties of a fluid formation system on drawdown and build-up performance. Their case is related to the present study but may be distinguished from it in that their numerical work and resulting graphs relate only to the performance of the pumping well itself. Incorrect values for in situ reservoir properties may be obtained from pump test data if the skin effect of the well and after-flow are not considered. Analysis of this problem by the authors indicated that the more reliable method of evaluating the influence of an adjacent gas field or expansible source was to use one well for pumping and another well at some distance from it for observing the aquifer pressure performance. An expansible source of hydrocarbon near a pumping well may be approximated by a line of constant pressure for a pump test. Fig. 1 illustrates a pumping well and an observation well near a line of constant pressure. Pressure behavior of an observation well during a drawdown pump test near a line of constant pressure is given by the diffusivity equation:

Jan 1, 1967

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending northeasterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 72¢ per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrother-mal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons. In 1946, on the basis of information obtained from 25 miles of mine workings and a completed exploratory program involving over 200,000 ft of diamond drilling, the present authors reviewed and brought up to date the geology of the orebody. More recently Sears," employing microscopic techniques, made a study of hydrothermal alteration and mineralization, and Howell and Schassberger'" restudied available geologic data. Production (1953) of molybdenite ore has been expanded to over 25,000 tpd and total production from 1918 through 1953 has been: Tungsten, tin, and pyrite are byproducts and monazite also was produced from 1949 through 1951, after which it was not saved. A maximum of 15 to 20 tons of monazite was produced. Geology of the Area Pre-Cambrian crystalline rocks constitute most of the Mosquito Range for several miles to the north, east, and south of the Climax molybdenite deposit, see Fig. 1. To the west the crystalline rocks are in fault contact with shales and sandstones of Pennsyl-vanian age. Both crystalline rocks and sediments are intruded by dikes and sills of Tertiary age. Numerous faults with small displacements are to be found in the crystalline rocks east of the Mosquito fault and in the sedimentary beds to the west. Pre-Cambrian Rocks: The pre-Cambrian rocks consist of schist and gneiss, identified with the Idaho Springs formation, and granite with minor pegmatite correlated with the Silver Plume granite of the Silver Plume area. The Idaho Springs formation is a general term applied to pre-Cambrian schist and gneiss found over a large part of the Colorado Front Range. At Climax this formation consists largely of biotite-schist and quartz-biotite gneiss with minor quantities of plagioclase and orthoclase, although in places appreciable quantities of feldspar and quartz are present in the more gneissic varieties. Locally, especially along the contact with granite, recrystal-lization of the schist has produced coarser texture and a more pronounced than average gneissic appearance. The gneiss and schist have been mapped as a single unit by Butler and Vanderwilt (1933)" and by Singewald (1951).12 Schist predominates at the higher elevations of the Mosquito Range and in the area to the north and east of Climax. The regional trend of schistosity is northeast with varying dips to the east. Silver Plume granite and associated pegmatite intrudes the Idaho Springs formation. Silver Plume granite in many places and in the Climax district in particular has an irregular form, and many large and small inclusions of schist and gneiss occur within the granite. Granite predominates at the surface in the immediate vicinity of the area of hydrothermal alteration and extends for several miles to the northeast and southeast. As more schist is present at lower levels of the mine than in the upper levels, the suggestion is that the granite is sill-like in form,

Jan 1, 1956

IT will be recalled that when educational instruction for the mineral industry began at Freiberg, at the beginning of the eighteenth century, the original aim was to organize and systematize the procedures previously followed by young men in gaining familiarity with the technology then in use. There must have been many other ideas current, even then, as to just what a young man needed to learn in order to become capable of assuming responsibility for the supervision and direction of such technical work. The problem in Europe was decidedly different from that in nineteenth-century America, because some of the European mines were actually owned and operated by the governing authority and the others were supervised, regulated, and taxed by it. The American problem was the efficient performance of technical operations; the European one was regulatory supervision. It was natural, therefore, that in the development of educational processes in Europe stress was laid on those factors which conserved and protected the interests of the state. The study of mineralogy and geology, leading to correct judgments as to the workability and value of mineral deposits; assaying, which gave the means of quantitative measurements, as did surveying; chemistry, which furnished a better basis of understanding for assaying, mineralogy, and geology; and physics and mathematics, which are the bases for the understanding and efficient use of mechanical appliances, became the core of systematic instruction for the mineral industry. It was early recognized that men could learn more than was already known about all of these subjects and education took on that dichotomy which still characterizes it; the teaching of established knowledge to the unlearned, and that of extending of the bounds of knowledge, now loosely termed research, which after two and a half centuries of work still shows

Jan 1, 1941

By S. Arthur Krom

(Wilkes-Barre meeting, June, 1911.) RECENT experiments indicate that the usual type of concentrating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentrating-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus many have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concentrating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is "bedded," that is, until a sufficient amount of metallic values have been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very lim-

Jul 1, 1911

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940

By Norman P. Goss

It is generally agreed that cold-working mechanically refines the grains into smaller fragments and with continued working these are oriented with certain crystallographic directions bearing a relation to the direction in which the metal is worked. Some of the energy expended on the metal during plastic deformation appears in the form of heat, but a very small portion remains in the metal as stored energy. The entropy, specific heat capacity, temperature at which recrystallization will just begin, density, ductility, elasticity, tensile strength, and resistance to corrosion are affected. These properties have been studied extensively and some of the changes in the physical properties due to cold-working were attributed to lattice distortion.l-8 The broadening of the Ka lines on the X-ray diffraction diagrams of plastically deformed metals is believed to indicate lattice distortion, and consequently the existence of internal stresses. The evidence supporting this theory rests solely upon the observed experimental fact that the diffraction lines are broadened and the Ka doublets are completely diffused. Elam9 has reviewed the matter of lattice distortion in relationship to the hardening of metals by plastic deformation. The X-ray diagrams of plastically deformed metals differ in general from annealed metals. The hardening of a metal was believed due to lattice distortion.9 The resolution of the doublet is lost when a metal is cold-worked and the Laue spots are elongated. At one time this elongation was thought to indicate the elastic bending of the crystal planes. However, more careful work showed that the asterism was due to new orientations developed within the fragmented grains during plastic deformation. Some theories attributed the hardening to fragmentation of the grains into smaller units. Jeffries and Archer,ll after carefully considering the problem of work-hardening from many angles, came to the conclusion that cold-working mechanically refines the grains into smaller crystal fragments, some of which at least differ in orientation from the parent grain. The increase in

Jan 1, 1940