Search Documents

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objection- able to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for efficient hand picking. At most mines an attempt is made to remove the visual impurities at one or more of the following places in the surface plant? (1) in the tipple during screening; (a) on picking band, belt, or shaking conveyors;*(3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller

Jan 1, 1943

By John Patek

KNOWLEDGE of the relative floatability of silicate minerals is increas-ing in importance as flotation is being applied to the concentration of nonsulfides. Many silicates are in themselves commercial products amenable to concentration by flotation. Moreover, the selective flota-tion of other nonsulfide minerals, such as cassiterite, depends largely upon the floatability of associated. gangue silicates. Differences in floatability existing between the various silicates have not been suffi-ciently appreciated; for example, the feldspars that differ greatly in floatability have generally been merely treated as "feldspar." It was the purpose of the work described in this paper to determine by experi-ment the differences in floatability between silicates; to investigate the causes for such differences, and to discover a means of predetermining approximate floatability without the necessity of experimentation.

Jan 1, 1934

By I. R. Kramer

A delay time for yielding in cold-worked face-centered-cubic metals was found. Slip on (123) planes was observed. Glide on these planes occurred during the delay-time period before slip starts on the (111) planes. AN important approach to the study of the anchoring and blocking of dislocations is available through the delayed-yield phenomenon which has been observed in body-centered and hexagonal close-packed metal by several investigators. Clark and his associate1-5 showed that a delay time for yielding is present in mild steels and fine-grain molybdenum. Type 302 stainless, SAE 4130 normalized, SAE 4130 quenched and tempered, and 24s-T aluminum aid not have a delay time. Kramer and Maddin6 studied the delay-yield effect. in metal single crystals. While they found a delay time in body-centered-cubic metals none could be found in the face-centered-cubic metals. Later7 a delay time was found in hexagonal close-packed metals. cottrell8 has proposed an explanation for the difference in the yield phenomena of b.c.c. and f.c.c. metals based upon the anchoring of edge dislocations by the proper types of impurity atoms (C and N). In the body-centered-cubic lattice the interstitial atoms are near a cube edge and can interact with an edge dislocation, while in a face-centered-cubic lattice the distortion around an interstitial atom is of spherical symmetry and cannot anchor a screw dislocation which has practically no hydrostatic component. Cottrell's theory seems to account rather well for the behavior of body-centered-cubic . metals. EXPERIMENTAL PROCEDURE The apparatus used in these experiments is essentially of the same design as described previously.' Single crystals 1 in. long and having a diameter of % in. were placed in a pendulum which consisted of a bar 8 ft long designed with a crystal holder to accommodate the specimen at low temperatures. This portion of the apparatus was supported on fine molybdenum wires. A bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on a set of roller bearings arranged around the periphery of the bar to allow accurate alignment. This bar was propelled by means of a spring-loaded gun and allowed to strike the lead bar in front of the single-crystal specimen. SR-4 type A-8 resistance strain gages were cemented to the specimen and the strain measurements were obtained by amplifying the strain-gage output by means of a high-gain preamplifier. A tektronix 545 oscilloscope was used together with a polaroid camera to record the strain and time sweep. An Ellis Associate Bridge was used to calibrate the strain gages and calibration readings were obtained before each test. The sweep of the time signal was initiated by means of a miniature thyraton which was fired when the two bars came into contact. The single-crystal specimens were cut from single-crystal bars about 12 in. long, grown by a modified Bridgman technique. The aluminum crystals were made with material of 99.99 pct purity while the purity of the copper was 99.999 pct. A cut-off wheel was used to prepare the specimens which were then machined to the desired length. The two opposite faces of the specimen were parallel to each other and perpendicular to the axis of the specimen. The specimens were compressed 1 pct. No machining followed thereafter. In some cases prestraining was carried out in liquid nitrogen by impacting the specimens directly in the apparatus so that subsequent observations could be made without allowing the specimen to warm up to room temperature. The single crystals were compressed 1 pct at room temperature in a hand press without much control of the rate of deformation. In some cases specimens were recompressed to obtain the desired length change. As far as could be determined in these experiments this factor did not seem to influence the results. The SR-4 strain gages were glued with a cellulose type cement onto the specimen surface and baked at 45°C for 12 hr. As a check on the baking treatment gages were allowed to dry at room temperature. All delay time tests in this paper were conducted in a liquid nitrogen bath at -195°C. A schematic delay time oscilloscope trace is shown in Fig. 1. At point B the elastic stress wave caused by the impact reaches the strain gage on the specimen. The portion BC is the elastic strain. In this investigation the strain at point C was used to calculate the critical resolved shear stress by multiplying by the proper modulus depending upon the orientation of the single-crystal specimen. The time between C and D is the delay time portion of the curve. This portion of the curve is fairly flat but does have a definite microstrain associated with it. After the point D is reached the specimen deforms rapidly and the strain reaches a maximum at E. Following this, depending upon the length of the bar behind the specimen, the strain remains constant for a period and then decreases when the reflected elastic wave returns from the end of the pendulum bar. A permanent plastic strain is recorded on the oscilloscope trace and also measured by a strain-measuring bridge. The strain, E p,

Jan 1, 1960

By B. Ladanyi, G. Archambault

It is generally recognized to date that a rational stability analysis of slopes and foundations in rock masses is a desirable but still rather remote goal of rock mechanics.1 In principle, a slope analysis is possible provided the original state of effective stress in the ground is known and the shear strength of the earth material can be clearly defined. In a macroscopically continuous earth medium such as soil, the two basic ingredients of the stability analysis in most cases can be assessed with sufficient approximation. A much less favorable situation exists when the slope is composed of a macroscopically discontinuous medium such as rock mass containing one or more sets of geological planar structures. In such a case, both the original effective stresses and the overall shear strength of the mass are much more difficult to determine. As for the former, it is only recently that certain calculation methods and solutions concerning the stress distribution2 and the seepage forces3 in a discontinuous medium have been proposed. As the strength behavior of the rock mass is concerned, much valuable effort has been made in recent years toward reaching a proper understanding of the phenomenon of rock mass failure under stress. Probably one of the most complete investigations of the problem to date has recently been made at the University of Illinois. The study resulted in establishing a first useful working hypothesis of the shear behavior of a regularly jointed rock mass, proposed by Patton in 1966.4 The main purpose of the work described in this chapter is to establish a more general framework for the shear behavior of rock mass, one that would be directly related to some basic rock parameters and would also

Jan 1, 1970

By J. B. Murdoch, John G. Jackson

The many mechanical, geological, and economic factors which influence the planning of a directional drilling program are thoroughly discussed and analyzed. It is demonstrated that the planning of a directionally drilled multiple-well artificial island location is a complicated undertaking and that it is imperative that complete planning and engineering analysis be undertaken before the program is started. Complete planning is profitable because all of the factors influencing the directional work are in general interrelated and many time compromises have to be made before a harmonious program results. The engineering control necessary to accomplish a complicated directional drilling program is outlined. Various means by which engineering control can be increased, such as cylinder drilling specifications, are given. A hypothetical example is developed for a complete offshore artificial island of ten wells to demonstrate the more important factors involved in the planning. Included with this example are special charts and tables which make more rapid the drafting of directional drilling proposals and maps. Introduction A petroleum engineer must consider many and varied factors when planning a long range directional drilling program for an offshore or inaccessible location on an oil structure. The basic principles of direc- tional drilling planning and operation must be reconciled with his company's drilling practices, and frequently special concessions to standard drilling and production practices should be made. The field techniques and tools used in directional drilling are well known and widely used, but the deliberate, careful planning of a complete directional program is in the main a recent innovation. This development, plus the increased demand for oil resources and the consequent exploitation of inaccessible structures and offshore locations, has placed this problem before many engineering departments for the first time. Directional drilling programs of a very complex and difficult nature have been successfully carried out in the Mid-Continent and Pacific Coast regions. The planning itself of a directional drilling project, however, has not had the careful analysis it deserves and we can reasonably expect widespread future progress along thesc lines. Data and experience gained in these programs by the directional drilling service companies and the oil producers have been studied with the objective of giving the engineer a better conception of the factors which govern the various steps in planning a series of directional wells. The newest engineering procedures are the result of recent careful analysis of years of directional drilling work accomplished under the supervision of directional drilling service companies working with the oil companies. The purpose of this paper is to illustrate

Jan 1, 1949

By L. J. W. JONES, B. H. Bennetts

THE removal and disposition of large quantities of slag from blast-furnaces is a question of great importance in the design of works, and various methods have been devised, from time to time, in order to take the best advantage of local conditions. In blast-furnaces treating copper-ores or lead-ores, it is necessary to use a fore-hearth, or matte-settler, in order to collect, if possible, every particle of valuable matte which, otherwise, would be carried away with the out-flowing slag. In all of these cases, the slag overflowing from the fore-hearth is caught in pots and then conveyed to the dump. If the slag is of no value and the necessary water-supply, grade and dumping-space be available, the disposal of the slag by granulation is by far the cheapest and best method. It involves a minimum of labor, both at the furnace and at the dump; and it permits a continuous outflow of slag from the furnace- or settling-pot, thereby avoiding frequent tapping and plugging. When the conditions of water-supply, grade and dump-area will not permit slag-granulation, there are three other methods in common use. Large steel or cast-iron pots, or ladles, supported by trunnions on heavy cars which are moved by steam-, air-, or electric locomotives; some type of mechanical conveyor; and small pots or buggies moved by hand. The pots on the slag-cars are generally circular or oval in shape, and each one contains from 15 to 40 or more en. ft. of molten material. The mechanism for tipping them is more or less elaborate; and, as a general rule, the slag is dumped alongside, and quite close to, the track. They are more or less costly to construct and to keep in repair, and, in order to use them to best advantage, it is necessary to have a good elevation of track above the dumping-ground; furthermore, the rails must be of heavy weight, and well-supported on heavy ties. Other disadvantages of the slag-pots are-1, that the slag cannot be removed continuously

Mar 1, 1905

By B. M. Larsen, T. E. Brower, J. W. Bain

A mass of circumstantial evidence is presented to indicate that the main source of alloy losses in open-hearth tapping is oxidation by air, with the steel apparently reacting with an amount of oxygen equivalent to about 30 times its own volume of air. The effect is erratic from heat to heat, depending largely on turbulence and distance of free fall of the stream of liquid metal. THIS paper reports another phase in a general study of oxidation in the open-hearth, various aspects of which have already been discussed in previous papers.1,2,3 It is based on experiments conducted on commercial, basic open-hearth furnaces at various times when opportunity offered, beginning about 1938, in an attempt to determine the mechanism and measure the amount of air oxidation during the flow of the tapping stream through the air into a ladle. This effect is closely connected, not only with alloy losses and control of chemical analysis, but possibly with various questions regarding inclusion content and steel quality and with a true picture of the deoxidation of steel in general. Thus it is believed that discussion of a large part of the results to date may be of assistance to others who are studying problems related to deoxidation or to steel cleanliness and quality. The literature reveals that strangely little attention has been devoted specifically to the effect of pouring steel through open air. Bardenheuer and Henke4 in 1939, in a paper devoted largely to overall losses of manganese in the basic open-hearth, reported that for a number of heats tapped into a tilted ladle held just beneath the runner so that the maximum distance of drop of the stream through the air was held to less than about 30 in., there was in most cases almost no loss of manganese from furnace to ladle. Hultgren,5 in 1945, showed that in high-carbon basic electric steel deoxidized in the furnace and containing no large inclusions as it left the furnace, large silicate inclusions, often rich in manganese oxide, were present in samples dipped from the pool in the ladle; also that the rise in content of large inclusions (above 0.01 mm dim) was greater when the metal stream was made to spray or flow in a turbulent manner. Our interest in this phase of oxidation in the open-hearth was first aroused by a study of alloy efficiencies on ladle additions. The frequency curves of manganese efficiency (net recovery of metal added in ladle) given in fig. 1 are of interest in this connection. Lowest, and also most variable (47 to 95 pct), recovery was in low-carbon heats having no coal additions to the ladle, progressing upward to a maximum average and least variable (82 to 97 pct) recovery in high-carbon heats killed with aluminum and silicon. Both coal additions and higher carbon contents in the tap stream, as well as additions of silicon and aluminum, help to lower the amount of manganese loss. But the most interesting point is the amount of manganese oxidized in many heats tapped at 0.50 to 1.06 pct carbon. It has been shown in a previous paper3 that the amount of oxygen in the tap stream in such heats is very small, usually below 0.01 pct, too small to oxidize any appreciable amount of manganese. Also, the fact that manganese should be oxidized at all in a metal solution containing such more stable oxide-forming elements as aluminum and silicon is an indication of some rather intense oxidizing effect such as could be caused by reaction with the air during ladle filling. Oxygen Balances from Tap Stream to Teeming Stream: Data in the form of alloy efficiencies, such as those shown in fig. 1, are not a proper measure of such a general oxidation effect. Having available

Jan 1, 1951

By J. J. Jakosky

A REVIEW of the progress in applied geophysics during the recent depression years reveals marked advances "over the methods employed several years ago. Of late, geophysical work has been curtailed to a con-siderable extent in the fields of oil and base-metal exploration, its especial domains a few years ago. Greater attention has been directed toward the use of geophysical technique in other engineering problems. Constantly maintained research programs have developed new instruments and per-fected better field, laboratory and interpretation techniques based on experience and skill acquired from years of application in the older geophysical field. During the past two years, geophysical methods have been employed in problems that required information on thickness of fill materials and subsurface bedrock contours. Considerable success has been attained, with subsequent drilling checking the predicted depths within one to five per cent. In general, these problems were similar as far as the fundamen-tal physical and geological conditions were concerned, but they have varied widely in specific detail and in engineering aspects. Character-istic of the different problems are: (1) yardage and bedrock profile in gold-placer mining; (2) water supply, involving underground drainage and storage conditions; (3) bedrock contours in dam-site and other structural investigations; (4) gravel and fill yardage, and other structural features along rights of way and in rock and gravel quarrying. Of particular interest, perhaps, to mining men are the problems of gold placer deposits and water supply. Geophysical work on gold placers is of especial interest because of the present expanded activity in all phases of gold mining. The development of a suitable water supply at, an economical cost is often of prime importance in insuring a successful mining venture. Particularly is this true in the arid Southwest. How-ever, the use of geophysical work in water supply is not confined to the needs of mining development.

Jan 1, 1933

Jan 1, 1888

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

HAVING produced one ton of concentrate that contains the copper that can profitably be saved or recovered from anywhere between 3 and 60 tons of mine ore, the ore-dressing engineer passes the result of his handiwork over to the metallurgist for smelting. Essentially, the concentrate is a damp mass of finely ground material consisting of copper sulphide minerals; pyrite, the sulphide of iron; and gangue, usually silica and silicates of aluminum. The purpose of smelting is to produce metallic copper and a slag containing the iron and siliceous constituents by pyrometallurgy-the kind of metallurgy that employs fire and heat to produce the chemical reactions through which it attains its object. Though blast furnaces have been used to smelt Porphyry-mine concentrates, notably at Braden, more than 90 per cent of [ ]

Jan 1, 1933

By Robert Glass Cleland

THE MEMBERS of the Phelps-Dodge, Phelps-James co- partnership differed widely from one another in certain aspects of temperament and personality; but in one thing Anson Phelps, William Dodge, and Daniel James were fundamentally alike. They were all bred in the English Puritan tradition. Their creed, moreover, was the stern, militant, uncompromising creed of John Calvin and John Knox. The present generation, harshly intolerant of such a creed, has little understanding of the authority it exercised on the thinking and conduct of its adherents or of the contributions that those same adherents made to human welfare and social progress. The men who accepted its authority "were characterized by a blend of strong individualism and an equally strong sense of social duty, and they submitted their own souls to the same searching scrutiny that they applied to their business ledgers." To all three of the immediate founders of Phelps Dodge, their religion was the most real and important thing in life. It was with them day and night, in joy and sorrow, in loss and prosperity, in their most trivial personal affairs, in business transactions of the greatest moment. It was with

Jan 1, 1952

By R. T. McLamore

Lack of sufficient native permeability or skin damage caused while drilling wells for in situ leach mining projects may necessitate stimulating injection and production we1ls to increase the leaching rate to economic levels. Such stimulation processes could include acidization, hydraulic fracturing, or explosive fracturing. This paper describes an explosive fracturing process that is being developed primarily to stimulate the production of oil and gas wells, but may be useful in in situ leach mining projects as well. The process utilizes a liquid explosive that has unique safety features. The chemicals that form the explosive are subdivided into two pumpable, non- detonable components. Technology has been developed to pump these two components independently but simultaneously into the well and blend them together downhole to form the explosive. As such, surface facilities and personnel are not exposed to explosive hazards. The explosive formulations utilized in the process have been subjected to numerous safety and characterization tests and been qualified for use in deep wells with temperatures and pressures up to 250°F and 10,000 psi. The explosive composition can be varied to produce an explosive ranging, energetically, from a blasting agent to a high explosive that can be detonated after injection into a borehole, a porous media or into thin naturally occurring fractures within the roc

Jan 1, 1974

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916

By Peretti, E. A.

Since its development about forty years ago by J. V. N. Dorr (Cyanidation and Concentration of Gold and Silver Ores, McGraw Hill Book Co., 1936, 1-5), and others, continuous countercurrent decantation has not only become one of the standard methods for extracting gold and silver from their ores, but has also found wide application in other metallurgical and chemical industries. In 1917 L. B. Eames published an excellent paper (Countercurrent Decantation, Trans AIME, 1917, 57, 143- 158), in which he determined the effects of grade of ore, ratio of solution precipitated to ore treated, variations in the density of the thickener spigot discharge and variations in the value of the barren solution upon the gold assay of the solutions discharged from the thickeners in the system. Eames showed that, other things being equal, the dissolved gold lost in the tailing varies directly as the value of the ore and as the value of the barren solution. The tailing loss de- creases rapidly as the ratio of solution precipitated to ore treated is increased to about three or four to one. Beyond this point the improvement is negligible.

Jan 1, 1949

By J. J. Kantner

CREEP investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that applica-tion of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and struc-tural character of the solid metal.

Jan 1, 1937

By R. R. Byran, M. H. Kuryla

The Compania de Real del Monte y Pachuca started a 10-ton pilot plant in March, 1906. The distinctive features of the first cyanide installations at Pachuca were: grinding in cyanide solution, all-sliming and filtration of ore in which silver constituted the major value. Loreto started with a 300-ton " all-sliming" plant, using jaw crushers, grinding in stamps, Chilean mills and pebble mills in cyanide solution, concentrating with Wilfley tables and Johnson vanners, classification by cones and Dorr classifiers, intermittent thickening by decantation, mechanical agitation in flat tanks by stirrers and centrifugal pumps, filtration in Butters filters and precipitation by zinc shavings. The "San Francisco" mill No, 1 was contemporaneous, using a rather similar flow sheet. We shall trace the main developlnents in the three large mills of the district to their present practice. Developments in Large Mills of District Crushing and Grinding.—The trend of development in this part of the work has been the same as throughout the milling world; via., all increase in the degree of comminution of the ore in dry-crushing machines, the advance from pebble mill to rock mill and then to ball mill and the elimination of the stamp battery through the encroachment upon its field on the one side by finer dry crushing and on the other by more efficient wet grinding. The single-stage crushing in jaw type crushers, used at the start, has been replaced by two stages; at first, both stages by gyratory type and later the present practice, which is the same in all three mills, consisting of gyratory as primary followed by cone as secondary and delivering a product that may be rated at 56 to 1 inch. Primary wet grinding, at first performed by stamps and Chilean mills, is now by hall and/or rod mills; present practice differing widely in the three mills. Santa Gertrudis uses a 7 by 15 ft. rod mill, San Rafael

Jan 1, 1935

By I. R. Kramer, P. D. Gorsuch, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By P. D. Gorsuch, I. R. Kramer, D. L. Newhouse

Although many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application aid tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + . . . , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann, in his work on the harden-ability of quenched steels, and Walter, in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield 2nd tensile strength.4 This is not true, however, for normalized

Jan 1, 1948

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of' cutting such a

Jan 1, 1892