Search Documents

By C. L. Kinney

The rapid increase in the amount of steel produced by the basic open-hearth process is an index of its ability to produce high-grade steel from raw materials of the most, varied physical character and chemical analysis. This inherent adaptability of the process has resulted in a lack of care in the selection of raw materials, so that in far too many cases charges are used of a chemical and physical character not justified by local economic conditions. A practice, or series of practices, should be used that will result in the greatest economy for the plant as a whole; therefore, the operations of blast furnace and open hearth must be considered together. In this paper, an effort has been made to show those variations in both open-hearth practice and cost that follow changes in the analysis of the pig iron arid it may be said that the theoretical costs shown are worthy of careful study and consideration. Carbon, manganese, silicon, phosphorus, and sulfur constitute the principal metalloids in basic pig iron and play the leading role in the production of steel by the basic open-hearth process. The percentages of each of these metalloids, with the exception of carbon, is a variable that has its genesis in the economic relation of the blast-furnace plant to its ore and fuel supplies. As the amount of carbon in the iron is a saturation function of the temperature at which it is produced, the variation in the amount carried is, for any given locality and grade of iron, practically negligible and is so considered in the eight heats discussed in this paper. The melting and refining reactions in an open-hearth furnace, either acid or basic, are essentially oxidizing and vary greatly with the type and age of the furnace, as well as the character of the fuel employed. The outstanding characteristic of the basic process, and the one that explains its predominance over the acid, is its ability to form out of the lime charged and the phosphorus oxidized from the charge a stable

Jan 1, 1924

By C. E. Lawall

ONE of the most important developments in the coal industry during 1940 was the continued uptrend in the production of bituminous coal. Estimated production for the year is 450,000,000 tons, with an additional production of anthracite of 50,000,000 tons making a total of approximately 500,000,000 tons. This is an increase of 12.5 per cent over 1939. Despite an estimated decrease of about 3.5 per cent in anthracite production, all of the major coal-producing states had increases in production for 9140. The national defense program, with the consequent increase in industrial activity, undoubtedly had an important effect on the increased demand for coal.

Jan 1, 1941

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,' we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By Georg Masing

Jan 1, 1933

By J. H. Brophy

Experimental evidence in recent years shows that nickel coated hydrogen reduced tungsten powder can be sintered to 98 pct of theoretical density at 1100°C. New data indicate that the sintering rate is the same for nickel contents ranging from 0.125 wt pct (mon-atomic layer) to 5.0 wt pct Ni coated on 0.561. tungsten powder. Nickel tungsten made by coreduction from oxides sinters in a kinetically similar way, but the rate tends to increase with higher nickel contents. The activation of sintering can be accomplished with a minimum amount of nickel if coated powder is used. Transverse rmpture strength was found to increase in specimens containing 0.25 pct Ni as density increased during the initial stage of the carrier-phase sintering process. Upon the onset of grain growth in the final stage, strength was found to decrease. With increasing nickel contents up to 4 pct, strength increased. Maximum strengths in three-point loading were observed at 73,000 psi for 0.25 pct Ni and 93,000 psi for 5 pct Ni. These were comparable to that of massive tungsten recrystal-lized in the presence of nickel and tested in the same way. The results were sensitive to the mode of powder treatment and ductility was negligible in all cases. The study and application of sintered bodies of nickel and tungsten is not new; however, the analysis of the mechanism by which small additions of nickel increase the sintering rate of tungsten promises to Contribute new information regarding sintering theory in general. Initial experimental evidence was presented by the authors showing that nickel-coated hydrogen-reduced tungsten powder may be sintered to 98 pct of theoretical density at 1100°C in 16 hr.' Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the 'solution-precipitationo step postulated when the carrier phase is liquid3 although in the nickel tungsten case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in mi-crostructures at the temperatures under consideration. In the present work, new data for nickel-coated tungsten powder are offered in support of the proposed mechanism, and a more explicit study of the second stage of densification is presented. Concurrently, the sintering kinetics of these coated powders are compared to Ni-W powder made by coreduction of oxides. In this way the present work can be compared to earlier results in nickel activated sintering of tungsten in which the coreduction process was emplyed. The ultimate utility of such an activated sintering process will be determined to some extent by the mechanical and physical properties of the final prod-

Jan 1, 1962

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By A. C. Spencer, H. F. Bain, E. C. Harder, Sidney Paige, C. M. Weld, W. Lindgren

At a meeting of the New York Section, on May 23, 1918, the sole subject of discussion was the nature and occurrence of iron ores in certain parts of the world." Owing to the importance of this subject, it has been deemed advisable to publish the remarks made at that meeting in the form of a paper, for presentation at the Milwaukee Meeting. The remarks related to the following districts: Page Brazil. By E. C. Harder................................. 116 Scandinavia. By Waldemar Lindgren..................... 120 Cuba. By C. M. Weld.................................. 124 Southern Europe. By A. C. Spencer...................... 130 China. By H. Foster Bain............................... 132 Alsace-Lorraine. By Sidney Paige......................... 135 Brazil BY E. C. HARDER† During the years immediately preceding the war, the iron ores of Brazil were attracting the attention of iron operators both in Europe and in the United States. This was due to the large quantities of practically undeveloped ore available, and to its great purity. It is reasonably safe to state that had capital not been diverted from the exploitation of these deposits to war purposes, Brazilian iron ores would probably now be offered in European and American markets. It is certain that after the war these ores will play a prominent part in the economic reconstruction of Europe and perhaps in the development of America. The Brazilian iron-ore field ranks among the six great iron-ore districts of the world, the others being: (1) The Lake Superior district of the United States; (2) the Lorraine ore field of northern France and southern Germany; (3) the magnetic deposits of northern Sweden; (4) the ore fields of Oriente, Cuba; and (5) the Wabana ores of Newfoundland. It is doubtless the greatest known undeveloped iron-ore district in the world. The Brazilian iron ores are situated in the State of Minas Geraes, the center of the district being located about 250 miles in a direct line west of

Jan 1, 1920

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

By M. E. Wadsworth, L. H. Raby, A. S. Peck

Infrared spec troscopy was used to study the adsorption of oleate collector on three varieties of hematite. Each of the minerals was found to react with either oleic acid or a solution of sodium oleate to form a mineral cation-collector anion chemisorbed layer at the solid-liquid interface. The chemisorption reaction displaced surface hydroxyls and was found to be pH dependent. The infrared band characteristic of the antisymmetrical C = 0 structural group of chemisorbed oleate appears between 1520 and 1540 cm-'. Evidence is presented which shows that molecular filming of the mineral surfaces with un-dissociated oleic acid precedes chemisorption. Infrared absorbance is correlated with the flotation behavior of the mineral. Adsorption processes are usually classified into two types which are distinguished and character- ized by the nature of the bond formed between the adsorbate and adsorbent. The process in which molecules chemically bond to solid surfaces is termed activated adsorption or chemisorption. If only weak van der Waals forces bind the molecules to the surface then the process is termed physical adsorption. Chemisorption is of primary interest in flotation systems since selectivity may be obtained if a single mineral is rendered air-avid by a specific collector mineral adsorption reaction. In previous studies infrared spectroscopy was used to define the mechanisms involved in the adsorption of oleic acid and sodium oleate on fluorite, barite, and calcite. Infrared techniques were particularly useful since adsorbed monolayers were identified in situ. Further, the infrared method permitted identification of reaction products in the solid, liquid, and vapor phases of the systems. The chemisorption reactions displaced F- from fluorite, SO4 from barite, and CO3 from calcite. This investigation was pursued in an effort to characterize and interpret the adsorption processes for synthetic hematite, compact red hematite, and specular hematite (crystalline hematite). Adsorption tests were performed using either oleic acid or

Jan 1, 1967

By Alfred E. Hunt

Tars paper is suggested by the appointment on the part of the American Societies of Mechanical and of Civil Engineers of committees upon the subjects of " Standard Tests and Methods of Testing," and " Uniform Methods of Tests of Material used in Metallic Structures," respectively, and by a study of the report of one of these committees, and other papers. Moreover, the writer has had frequent occasion to hear the complahts of tnanufacturers who furnish structural material subject to specifications, that in the tests prescribed, the number of tests required, and the methods of making

Jan 1, 1892

By C. H. Fulton

Page Introduction........................... 280 Distillation Products from Reduction of Zinc Ore........... 281 Preliminary Investigations..................... 290 Equilibrium of Reaction Zn + CO2 + ZnO + CO in Temperature Range of Condensation........................ 293 Requisites for Successful Condensation................ 299 Discussion............................ 300 Introduction The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zine-furnace work. recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,l "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; ...... when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder." This difficulty was not encountered in the electric furnace used12 the main difficulty being the destruction of the fire-brick lining of the large condenser, in certain parts, and the formation of .some oxide and dross coatings on the condensing surfaces. The reason for these difficulties could readily be explained by the infiltration of air whenever the condenser was changed from one retort base to the other, the zinc absorbed in the fire-brick forming oxide and causing rupture by its expending volume. Two facts, however, tended to disprove this theory for the rupture of the fire-brick lining: first, the large distilling retort, lined with fire-brick, which was shifted from charge to charge on alternate bases at temperatures between 1200 and 1300 C., fully exposed to the air, showed no signs of disintegration whatever; second, marked disintegration in the condenser occurred .only in places that were at tempera-

Jan 1, 1919

C. W. GENNET, JR.,* Chicago, 111. (written discussion?).-Since the Lehigh Valley accident, transverse fissures have become a source of constant anxiety to railroad officials, because such defects, only infrequently detected by the trackmen, may appear under a moving train entirely without warning. The number of actual accidents resulting from rails containing fissures is no doubt a small proportion of the total, but the serious losses that have been directly attributable to fissures, coupled with the continual possibility of repetition, creates an alarming situation which demands a full investigation of the cause of fissures; apart from other types of rail failures. Mr. Howard's position gives him a field for action and an opportunity for laboratory examination and research that are unsurpassed, and the results. of his investigations must be received with the utmost attention and respect. His admirable paper, summarizing his previously published studies and analyses of the transverse fissure problem, constitutes a convincing treatment of the subject chiefly from the standpoint of stress and strain to which rails are subjected. The intricacies of the problem are so great that seemingly any theory advanced for the cause of fissures may be attacked from some angle; and although Mr. Howard's deductions are logical in the direction followed, it is apparently necessary for considerable work to be done along other lines before his theories can be fully accepted. It is generally conceded that fissures, whether fundamentally clue to fatigue or something else, are of a progressive character, their ultimate size' being the result of growth from an originating nucleus or point of rupture. Abundant proof of this lies in the variable sizes of the fissures found, and there can be no doubt that their development or growth is the result of the strains to which rails are subjected in the track. Obviously, therefore, the most important factor in investigating the cause for fissures lies in determining the conditions that exist at the point or

Jan 4, 1918

By H. P. Allen

THE chloridizing mill of the Standard Reduction Co. is located about 75 miles south of Salt Lake City on the Tintic branch of the Denver & Rio Grande Western R. R. and 12 miles from the Tintic Standard mine. The daily capacity is 200 tons of a siliceous, low-grade, silver-lead ore from this property. It has operated continuously since it was started in January, 1921. The process consists essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid, the precipitation of silver on sponge copper and of copper and lead on tin-plate cuttings. The precipitates are shipped to a smelter. Some of the general ideas involved are said to have been used by Augustin in England, in 1840. A number of textbooks treat of the subject, especially the chloridizing roast followed by a leach with sodium hyposulfite or amalgamation. The process was revived in this district by Theo. P. Holt, N. C. Christensen, the Bureau of Mines, and others.

Jan 8, 1925

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By C. W. Hill

IN a previous article preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) FIG. 1.-STEPS IN THE ELIMINATION OF LEAD. (The lead line, at point 105.8 in the violet portion of the spectrum, is seen between the two copper Lines,-102.29 and -106.29, lying close to the latter. The crowded faint lines are due to the carbon are.) 1. OUTLINE OF METHOD A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 10, 1918

By J. S. Hegwer, P. M. Dunlap

An improved acid for the treatrrzent of sulfate-con-raining limestones and dolomites is described. The acid is designed to reduce he reprecipitation of dissolved calcium sulfate and the possibility of plugging permeable flow channels. In addition, this improved acid has a much lower reaction rate than that of regular acid; the advantages of a "retarded" acid are obtainable. Field testing of the acid has shown it suitable for use in sulfate-containing formations. Substantial improvements in productivity generally resulted. INTRODUCTION Acid treatments of limestones, dolomites and other formations bearing carbonate deposits are frequently unsuccessful when the calcareous formation contains sulfate, either as anhydrite (CaSO,) or gypsum (CaSO4. 2H2O). Preliminary dissolution in acid followed by redeposition of calcium sulfate appears to be a major factor contributing to poor well performance after acidizing. The precipitate is usually the gypsum form of calcium sulfate, but in higher temperature formations it may be anhydrite. The freshly precipitated crystals are nearly always very small and needle-like. They may occupy a gross volume many times that of the original anhydrite crystals and will obviously constitute an impediment to flow through newly enlarged flow channels. It is believed that the redeposition problem is most severe when anhydrite lines the fracture systems and large pores which supply the effective permeability of a formation. Microscopic inclusions of calcium sulfate also present large sulfate surface areas for dissolution in acid. In either case, great amounts of calcium sulfate may dissolve before the acid can be spent on formation carbonates. For regular spent acid (originally 15 per cent hydrochloric acid) the precipitate could be as much as 270 Ib gypsum/1000 gal acid. Two techniques have been applied by the industry for reducing sulfate plugging during acidizing. The method'.' commonly employed in the field is the attempted removal of a quantity of regular treating acid before it has reacted completely with the formation. This is practiced because the solubility of calcium sulfate is greater in a solution that is still acidic than in one which has been largely spent on the formation rock. The chance of precipitative plugging is therefore reduced if the withdrawal is successful. However, it is often impossible to get the acid out of the formation before precipitation occurs. A second possible method, which at first glance appears practical, involves addition to the acid of sequestering agents which form strong soluble complexes with calcium ions. These chemicals do increase the "solubility" of calcium sulfate in fresh acid, but to a lesser extent in spent acid. The sequestering agents have, therefore, proved unsatisfactory because the amount of sulfate eventually deposited from the spent acid may be greater than that from regular acid. Another logical approach to the problem of calcium sulfate reprecipitation is the prevention of the initial dissolution of calcium sulfate by the common ion effect. This may be accomplished by adding a soluble calcium salt to the fresh acid. The use of calcium salts in treating acids is not entirely new. An earlier suggested use of a soluble calcium salt in hydrochloric acid apparently failed to recognize the full extent to which the solubility of calcium sulfate could be suppressed. The present study extends this earlier work and adds certain improvements toward the development of a practical anti-anhydrite acid. LABORATORY DEVELOPMENT Calcium Sulfate Solubility Table 1 shows the results of a laboratory study performed to establish the effect of calcium chloride concentration on gypsum solubility. Because of the strong tendency of calcium sulfate to form supersaturated solutions, accurate solubilities are difficult to determine. These solubility data probably are reliable to within ± 15 per cent. The solubility of calcium sulfate in 15 weight per cent hydrochloric acid increases with increasing temperature. This trend is also followed in hydrochloric acid which cantains calcium chloride. This is contrary to the solubility behavior of calcium sulfate in water, wherein the solubility decreases with increasing temperature.

By L. Albert, A. M. Cameron, J. W. Gullick

International Nickel has 15 operating mines in Canada, and. 3 mines which are being maintained on a standby basis. Annual production is about 20 million dry short tons of ore, most of which is from underground mines, the remainder from open pit mines. Although some of the underground mines are served by ramps for trackless vehicles, most men, materials and ore are hoisted in vertical shafts. In addition to shafts and raises for ventilation and service purposes which are not equipped with hoisting plants, there are now 28 vertical shafts at Inco mines served by 47 hoists. Of these, 22 shafts and 36 hoists are located in the Sudbury District of Ontario, one shaft and two hoists are at the Shebandowan mine in Western Ontario, and 5 shafts with 9 hoists are located near Thompson, Manitoba. This paper describes the components of Inco hoisting plants-which have been applied at different times and under different conditions, and indicates the rationale for the various designs. Some engineering and maintenance practices, considered advantageous, are also described. MINE SHAFTS Many of the shafts sunk in the early days of the Sudbury District, on what are now Inco properties, were inclined shafts. Of the identifiable shafts sunk between 1885 and 1920, thirteen were inclined and at least four were vertical. Since 1920, thirty vertical and two inclined shafts have been sunk. All of the inclined shafts have been abandoned for hoisting purposes but the majority are still in use as service or ventilation ways. Shafts at Thompson- and Shebandowan are all vertical. The vertical shafts range from 2 or 3 compartment exploration and development shafts to 6 compartment shafts for ore, man and material hoisting. They vary in depth from 1,050 to 7,137 feet and in addition to hoisting compartments all contain manway and service compartments. Prior to 1948, unlined rectangular shafts with timber sets and guides were used. The rectangular cross-section was favoured since the rock is competent, the shape compatible with timber set framing, and since available shaft space could be used efficiently. Resistance to air flow was not of prime importance. Concrete linings were introduced for the first time at the Creighton No. 7 Shaft which was collared in 1948. All major shafts since that date have been concrete lined. Vertical set intervals were increased in steps, with the introduction of structural steel sets secured to the concrete linings. Whereas 7 foot set intervals were used with timber framing, this increased to 10 feet 6 inches with steel sets and more recently to 15 feet with steel and steel backed wood guides. With the advent of deeper shafts, or shafts which are expected to be deepened, the trend is to circular concrete lined shafts. The majority of shaft guides in service are of select Douglas Fir. This practice commenced as a component of timbered shaft design but continued as a

Jan 1, 1975