Search Documents

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By A. Kaufmann, B. Cullity, G. Bitsianes

T0 determine the bulk of the phase diagram, techniques for melting, thermal analysis, heat treatment, metallography, and X-ray diffraction that have already been described were used.' It proved difficult to get definitive results for most of the alloy system because of the large number of compounds, their high melting points, and their extreme brittle-ness which made metallography difficult. The final phase diagram, essentially as shown in Fig. 1, was issued with considerable trepidation.' The phase relationships at the two ends of the system were defined with satisfactory accuracy. In the central region between U,Si, and USi, there was great uncertainty concerning the melting points and even the composition of the compounds. At the uranium end of the system, it is quite clear that a eutectic exists at about 985 °C and approximately 8 or 9 atomic pct Si. The a-to-8 transformation is not appreciably altered by silicon, but the 8-to-y transformation is raised to about 795°C. There is appreciable solid solubility in y-uranium, as demonstrated by the micrographs of Fig. 2. The occurrence of the E phase was not suspected at first, since the alloys as melted and furnace cooled gave no X-ray diffraction or thermal arrest indication of it. However, suitable metallography revealed a rim around each of the compound particles as shown in Fig. 3. Heat treatment above 600°C revealed that the rim was another phase which formed by peritectoid reaction between uranium and U,Si,. This reaction proceeds slowly and it is difficult to get it to go to completion. Consequently, there is some uncertainty concerning the exact composition of P and the exact peritectoid temperature. On the basis of various metallurgical studies, it was decided that the most probable composition for t was about 23 atomic pct Si. Metallographic examination shows the closest approach to a single phase at this composition. Likewise, density and hardness measurements of heat-treated alloys shown in Figs. 9 and 10 show a change in slope at 23 pct Si. This is revealed most clearly by plotting the difference in hardness or density between chill-cast and heat- treated alloys as shown in Fig. 4. Zachariasen2 was able to index the diffraction lines of P and to determine the arrangement of the atoms in the unit cell. He concluded that the composition must be US. However, it is felt that the metallurgical studies are reliable and that Zachariasen's X-ray work does not furnish positive proof that the P phase exists exactly at the stoichiometric composition U3Si. There are many instances in alloy systems where a phase does not occur at the composition dictated by the molecular structure. It is possible that the chemical analyses used in the present work were subject to some systematic error. This seems unlikely, however, since recent work in several laboratories seems to show excess compound at 25 atomic pct Si.

Jan 1, 1958

several days before leaving Buffalo; influenza developed, and when his train reached Nashville, Tenn., he was too ill to continue his journey and was taken to the Kissam Hall Hospital, Vanderbilt University, where he died of pneumonia. He was a young man of unusual ability and high moral character, always brigh.t, happy and kind, faithful and honorable in all things; loved by both his associates and those under his authority. His life and character cannot be better described than by the following quotation from one of his superior officers: "Lieutenant Ohnsorg was a man loved by all of us, always cheerful, just and kind, with unusual executive ability. We can never expect to find a man who has his ability and fine temperament and his position can never be sled as he filled it." He was happily married and leaves to mourn his loss a wife, Constance E. (Rogers) Ohnsorg and a baby girl born since his death, Nov. 29, 1918, a father, W. H. Ohnsorg, mother, Ida May Ohnsorg, and a sister, Mrs. Stuart Strathy McNair. He was a member of the American Institute of Mining Engineers and of the Florida Phosphate Miners' Association. Lieutenant Edward Hale Perry At the height of the first great German'offensive -of'the Spring of 1918, Edward Hale Perry, of Boston, First Lieutenant, Company D, Sixth Regiment Engineers, U. S. Army, was killed on March 30, near War fusee—Aban-court, Picardy, France, while defending the Boisdes Tailloux against the terrific plunge aimed at Amiens. Lieutenant Perry was born in Boston, Jan. 23, 1887, the son of Georgianna W. and the late Charles F. Perry. After completion of his college preparatory course, he travelled for a year in South America and Europe before entering Harvard with the class of 1910. It might have been regarded as the natural thing for Perry, upon graduation, to choose a path that would lead to a business or professional career at home, but there were in his character a solidity, a horror of sham, a contempt for the "soft" things, and a love-of the open which caused him to be attracted to a life of stern and sturdy reality. Accordingly, he entered the graduate mining school at Harvard, and received the degree of Mining Engineer in 1913. In the meantime, two summers spent in Western mining camps had at-

Jan 1, 1920

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By Reynold Q. Shotts

The small domestic underfeed stoker as now designed is unusually sensitive to the coking and plastic properties of coals, and when the attempt is made to burn the high rank coking and caking coals of the Appalachian fields, serious trouble may occur. Part of the trouble may be caused by the ash content and clinkering characteristics of the particular coal in use, but more often it is the result of an excessive ac-in of coke in the form of ''trees,, or masses in the fuel bed. Often the zone of burning becomes so restricted that the fire goes out, and in extreme cases the fire may be lifted completely out of the fuel bed and away from the air ports. Even if the fire is preserved, excessive coking may cause response to subsequent heat demand to be slow and irregular. Coke trees seem to grow most readily during periods of hold-fire operation, so that in order to preserve the fire in mild weather it is often necessary to set the timer for such a long operating period each hour that much unneeded and unwanted heat is developed, causing discomfort. During demand periods the fire may pick up so slowly that the intense burning which develops just before stoker cut-off causes a serious overshooting of the thermostat. Stoker coal performance tests which have been made in a number of labora- tories1,2,3,4,5 are one method of approach to the problem Of selecting stoker coals- As yet these tests have not been standardized and they are expensive and time-consuming. The value of the results probably increases with the length of the test. Sherman and co-workers at Battelle Memorial Institute believe that even a one-week test is not too reliable a trial2 and it is quite likely that Others will agree. A great advantage of such tests is that characteristics of coals, other than the tendency to form coke masses, may be evaluated from them. The selection of stoker coals would be greatly facilitated if there existed some simp1e measure Of the tendency Of a a to form coke in a fuel bed. Although possessing all Of the disadvantages Of any small-scale laboratory test, the test for the free-swelling index of coal has been found useful for evaluating the probable effects Of swelling properties upon combustion.7 Ostborg, Limbacherand Sherman, have shown that the test can Predict, roughly, the tendency Of coke to accumulate in the fuel bed Of a domestic stoker. They also gave instances of its value in predicting combustion behavior in some large installations. The use of the test for free-swelling index has become well established and has been adopted as a standard by the American Society for Testing Materials.8 When domestic stoker coal investigations began at the State Mine Experiment Station in the summer of 1944, it was decided

Jan 1, 1949

By P. Lindstrom

Retreat mining, using yielding steel friction props, over a 7-year period has been successful at a uranium mine operated by Hecla Mining Co. in southeast Utah. The support system allows good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered. Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths. The Radon mine was one of the first American metal mines to use yielding steel props for supporting the relaxed core of the pressure arch which is induced by retreating longwall mining. Full caving was induced. After more than 7 years of stoping experience, the method has proved very satisfactory for the conditions encountered. The mine and method have been described in references listed in the bibliography. U.S. Bureau of Mines Information Circular 8004 by Wilbert Dare and Philip Lindstrom gives the most information. Stoping experience at this mine indicates that there are many advantages to be gained by using yielding supports; such as in safety, timber cost, roof control, ventilation, ore dilution, and low cost per pound of metal produced. Subsidence measurements show that the surface will rise rather than slump in some areas over the mine. This appears to be an unusual observation and is presented as a new development in subsidence studies. The Radon mine is located 35 miles southeast of Moab, Utah in the north end of the Big Indian mining district in San Juan County. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual premiums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining. The principle of working under the relaxed core of

Jan 1, 1964

By Marshall B. Standing, Donald L. Katz

DENSITY data are reported on 16 saturated hydrocarbon vapors at pressures ranging from 1000 to 8220 lb. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. INTRODUCTION The densities of natural gases are necessary in many engineering computations in petroleum production and utilization. Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 lb. per sq. in.4 Recent discoveries of pools having pressures up to 7500 lb. per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data on gas density at high pressures. METHODS OF COMPUTATION The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The methane-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by Sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir or while on contact with liquid during flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those considerably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions. This paper reports the density of 16 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure' have been modified and enlarged. A simplified method of obtaining gas density is presented in the form of charts, which apply for specific groups of gases.

Jan 1, 1941

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,' Si,' Ni,2-5 CO,'-', Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry's law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.'2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

SEC. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6, Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in • special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than twenty-seven years of age at the time of election. The rights of the present Junior Associates shall continue until the same expire by limitation of time. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life memberships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute,

Jan 1, 1929

By David J. Mack, A. H. Kasberg

The transformation characteristics are found to resemble a similar binary alloy. The differences are due to the alpha iron particles. While strength properties of the isothermally transformed alloys are high, ductility is low, resulting in high notch sensitivity. The elastic modulus can be varied widely and correlates with strength. Abnormal grain growth sometimes occurs. A CONSIDERABLE amount of work has been done on the isothermal transformation of high purity aluminum bronzes using the methods pioneered by Davenport and Bain.' The first isothermal study of these alloys was made by Smith and Lind-lief,' but more recently Mack", " and Klier and Grymko5 have continued the work. In commercial aluminum bronzes, one or more elements are always added to refine the ß grain size and to improve the mechanical properties. The effect of these elements on the isothermal transformation has not been reported in the literature. No systematic study of the properties of isother-mally transformed aluminum bronzes has apparently been reported, although adequate information is available on their properties after more conventional heat treatments. The fact that a eutectoid alloy will reject face-centered cubic a during isothermal transformation at appropriate temperatures2'" warrants investigation of the properties of such structures. Another cogent reason for determination of properties is the fact that the modulus of elasticity of the eutectoid alloy varies widely with the nature of the heat treatment." Preliminary experiments7 indicated that a high purity eutectoid alloy would not give reproducible results in property determinations because of ex- cessive ß grain growth during heat treatment, a single ß grain frequently occupying the entire cross-section of a standard test bar. For this reason a commercial aluminum bronze containing iron as a grain growth inhibitor was used. The isothermal transformation diagram of the alloy was first determined. On this basis, the heat treatments necessary to produce representative structures were selected and the properties determined. Material A commercial alloy (Ampco Grade 20) of the following composition was used: Cu, 83.68 pct; Al, 12.31 pct; Fe, 3.68 pct; Ni, 0.28 pct; and Mn, 0.03 pct. This alloy proved to be very close to the eutectoid composition and may be compared with the accepted value of 11.8 pct A1 in the binary Cu-A1 system. Comparison is valid only because of the "negative replacement effect" of the iron? Since traces of excess y² are present, the alloy is slightly hyper-eutectoid. The material was received in the form of 3/4 in. round, hot extruded bars. Specimens of approximately ? in. thickness were cut from this stock and drilled to allow suspension in the salt bath. The structure of the as-received material varied from 5 to 40 pct a + y2* in a matrix of ß. The amount of a + y² present was dependent upon the ß grain size of the extruded material. The coarse grained portions did not form as much a + Y, as did

Jan 1, 1952

Molybdenum was first discovered on the Continental Divide in Colorado in 19 11; and in 1918 two companies, one of which was the Climax Molybdenum 250 stpd operation, were producing. In 1919 both mines were shut down, but in 1924 the Climax mine reopened and has been producing ever since. Over the years mine production has been increased until today the mill capacity is 48,000 stpd (43,500 mtpd). From 1935 to 1973 all ore was mined underground by block caving with scraper slushing. Since 1973 ore production has been supplemented by open pit mining. As demand for molybdenum increased, upper levels of the mine became worked-out and new lower levels were opened. In late 1972 production began on the 600 level with the mined ore being primary and secondary crushed in the new No. 4 crushing station. Ore is hauled to the primary in 10 st (9. 1 mt) capacity Granby side-dump cars. The trains, carrying 200 st (181 mt), pass throug.h a dump block and discharge directly into a 54 in. by 84 in. Traylor TC gyratory crusher set at an 8 in. (203 mm) open side setting. Since the ore has already been broken to a size which will pass the finger raises in the mining areas, there are only rare oversize boulders to block the crusher opening. Selection of the crusher was based more on its capacity than its receiving opening, as is often the case with gyratories used in open pit operations. Nominal and maximum capacities for this unit are 1250 and 1800 stph (1 135 and 1635 mtph). The ore is often wet and sticky, so a mechanical car cleaning device is utilized. Under the crusher is a 300 st (270 mt) ore pocket equipped with a 60 in. (1.52 m) wide inclined conveyor which delivers the ore to a 2,000 st (1800 mt) surge bin. Near the head pulley of this conveyor is a wood picking station whe re tramp wood and steel are put into cars for removal. Two more apron feeders remove the primary crushed ore from the surge bin, and impact belts and conveyor belts transport the ore to the crushing station for screening ahead of two 7 ft (2. 13 m) standard crushers. Secondary crushed ore is then conveyed to the surface for tertiary crushing. The entire underground crushing room containing the primary, two secondaries, screens and related equipment is serviced by a 100 st (90 mt) crane with a smaller capacity fast hook. A control room is situated so the operator can observe all the crushing operations. Rotoclone collectors remove dust from the entire operation (including the fumes from the zinc pots) and discharge it to the final product belt. The Rotoclones are vented through drifts and raises to the surface. Shop facilities, electrical gear, and lubrication equipment are located

Jan 1, 1978

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By J. D. Price, W. M. Bertholf

One of the chief difficulties with which the operator of a coal washing plant has been forced to contend is the handling of the very fine coal. First he has the problem of separating the fine coal from washery water. This is usually accomplished by the use of settling cones or Dorr thickeners: in either event the separated fine coal contains a high amount (40 to 80 pct) of water and, somewhat loosely, dependent upon the size of the coal particles present, may be known as sludge or slurry. His second problem is the satisfactory further dewatering of such separated sludge and/or slurry. At the coal washing plant of the Colorado Fuel and Iron Corp., washed coal from the Deister Plat-O tables is sluiced to a stationary inclined de-watering screen provided with 3/16 by 1-in. slots, and the coarse coal passing over this screen is conveyed by a Baum-type elevator and a flight-type distributing conveyor to a battery of Carpenter centrifugal driers. The fine coal and water passing through the openings of the primary dewatering screens, plus the fine coal passing through the screens of the centrifugal driers (and no small portion of which is the result of the disintegrating action of these driers) is pumped to two 30-ft Link Belt settling cones. The sludge recovered as underflow from these cones was formerly dewatered on stationary screens having 1/16 by 1-in. slots and discharged on top of the coarse washed coal in the Baum drainage conveyor; but after a relatively few hours of op eration the circulating load of fine coal on this conveyor built up to a point where it became necessary to reduce the quantity of feed to the washing tables. The original arrangement of our coal washing and dewatering equipment is shown in Fig 1. In order to regain the loss in active throughput which had been caused by this circulating load, an installation of six vibrating filters was made during the year of 1936. This resulted in an increase in normal tonnage of washed coal from 1430 to 1750 tons per 8-hr shift, a gain of slightly over 22 pct. This increase in throughput has made a very substantial decrease in the " conversion cost" per ton of washed coal. Since the vibrators were installed, we have gained about 2,000,000 tons in production, compared to what would have been produced in the same number of shifts at the former rate. Putting it in slightly different form, we have saved in the past 12 yr the cost of 1400 operating shifts in the washery. Fig 2 shows the location of the vibrating filters as applied to the original flowsheet. It will be noted that the sludge from the bottom of the settling cones is passed through a distributing box and thence to the filters. The de-watered coal from the filters is de-livered to the conveyor receiving the dried coal from the Carpenter driers.

Jan 1, 1950

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By James R. I. Henagan, William O. Crego

The Mamou Field, located in Evangeline Parish, La., is an elongated anticlinal structure on the downthrown side of a major east-west fault with oil and gas production from the upper part of the Wilcox formation. Two main producing horizons occur at an approximate depth of 11,500 ft and have been designated the Morein sand and the Deshotels sand. The upper sand (Morein) had an original bottom-hole pressure of 6,788 psig, which is some 1,500 psi above the normal pressure for that depth. Oil production with high gas/oil ratios and fluid analyses giving high shrinkage factors prompted a study of the reservoir in its early stages. The results indicated a closed reservoir producing under solution gas drive with low expected ultimate oil recovery. The early study of the Wilcox formation and its contained hydrocarbons resulted in the presentation of the data to the Department of Conservation of the State of Louisiana. with suggestions for field rules and a request for permission to inject extraneous water into the Morein sand. The water injection plans eventually led to complete unitization of working and royalty interests, to the construction of a gasoline plant, and to a central tank battery installation for the field. Deshotels sand wells were reworked to the Morein sand, and the water injection system was installed and ready for continuous operation in the early part of 1949. The injection of water was started in time to arrest the bottom-hole pressure decline at or near the bubble-point pressure. This injection was calculated to increase the ultimate recovery and to conserve natural resources. Pressure maintenance, the extraction of LPG products, and the sale of residue gas (early 1950) represent an attempt to produce an oil field with utmost efficiency. INTRODUCTION The two principal Wilcox oil horizons in the Mamou Field are the Morein sand and the Deshotels sand, occurring at 11,500 ft and 11,700 ft subsea, respectively. Minor oil production has been encountered in Morein stringer sands. (Fig. 1.) This paper deals only with the Morein sand, which is blanket over the Mamou Field. It is, however, segmented by the northwest-southeast "E" fault as shown in Fig. 2. The west segment is the area involved in the water injection pressure maintenance program. To date the east segment has operated largely under the influence of a strong water drive. The paper presents (1) a brief history of field development, (2) a resumé of reservoir conditions which led to the decision to inject extraneous salt water into the principal producing horizon, and (3) a summary of reservoir analysis and performance. FIELD DEVELOPMENT The Mamou Field is located in Evangeline Parish, La. The discovery well (J. B. Morein No. 1, now Unit No. 5) was completed in December, 1945, after penetrating 200 ft into the Wilcox formation. Initial production from the Morein

Jan 1, 1951

By A. D. Dorenfeld

Factorial design is a mathematical method of drawing valid conclusions from a series of tests made in a predetermined pattern. It is applied to flotation ore testing using, in this case, five variables, each varied twice, requiring a total of 32 tests. Representative conclusions are checked by repeat testing. THE factorial design method of testing is particu-J- larly applicable to mill-scale plant tests because 1—the conclusions take into consideration all variabilities of the plant, 2—there are no subjective guesses as to the conclusions, 3—the number of tests necessary to check large numbers of variables are at a minimum, and 4—interactions between variables can be discerned. It is equally applicable to laboratory testing because once the variables to be investigated have been decided upon, as well as the number of levels for each variable, a well-trained assistant can run the tests, since the test work follows a predetermined mathematical pattern, leaving the conclusions to be found by the person in charge. The conclusion takes into consideration all errors of the tests. To illustrate the use of factorial design, a sample of copper porphyry ore was tested, the copper content of the batches not being uniform. Five variables were investigated, each at two levels, requiring only 32 tests. After suitable arithmetical analysis, conclusions for copper recovery and concentrate grade are arrived at. Four cases of these conclusions are checked by repeat testing. Testing Methods Reproducibility of flotation tests varies widely, depending on the experimenter, the process, the equipment, and probably a host of unknown and perhaps interacting variables. If the reproducibility of tests is good, let us say to 0.2 pct recovery of a certain metal, and the minimum difference between tests upon the variation of the interested variables is, say 1 pct, then simple averaging and inspection is ample in interpreting results. However, often such a happy situation is not the case. This is particularly true in mill-scale operations where the ores are variable, and a host of minor operating fluctuations common to most milling, and familiar to all mill operators, is the normal state of affairs. Yet, mill scale tests are run, the results averaged, and conclusions drawn therefrom. The trustworthiness of such results should be measured by comparison to the experimental error—the measure of the degree of reproducibility of the results. This comparison is a test of significance. Thus, if daily results of recoveries average 80.0 pct, and a spread of 78.0 pct to 82.0 pct, is recorded, then, clearly, on changing mill operations, an 81 pct recovery cannot be construed as significant by using averages, since it is well within the previous test limits. By using rigorous statistical tests of significance, conclusions arrived at by inspection or simple averaging may be shown to be based on inadequate evidence or even wrong. In any event, a plant super-

Jan 1, 1952

By B. F. Oliver

A levitation zone melter is described which has the necessary characteristics for processing metals of controlled purity. No crucible is required; control of the solidification variables is stable; the environment of the charge is chenzically controlled. Rotation of the solidifying interface and mixing in the liquid by the magnetohydrodynamic stirring produce an eight-fold increase in freezing velocity over former melting units with better resulting solute redistributions. The smooth appearance of processed specimens, resistivity ratios as a hnction of position, as well as a segregation curve, are presented as evidence of smooth continuous solute fransport over distances in excess of ten zone lengths. THE difficulties of the floating zone-purification of higher density metals in large quantities under conditions of lowered surface tension are well known and have hindered fundamental research programs for some time. The inordinate amount of time required to obtain a small reproducible yield of high-quality metal has excluded the use of such material for many important material research programs. However, with the use of controllable induction levitation forces' to accomplish stable liquid zones with nearly flat solidifying interfaces, and with good physical and chemical control of the processes involved, these difficulties can be overcome. A zone melter that is to be used for both high-purity and controlled composition work in metal systems must have the following three characteristics: 1) The process must avoid the use of containers. 2) Physical control of the solid-liquid interface and of the mixing within the liquid phase must be stable. 3) The chemical environment of the melt chamber must be controllable. A description of an apparatus that accomplishes these objectives follows.* APPARATUS One of the basic features that is necessary for good process control of large sections is that the charge, the coil, and the motion mechanisms be within the same chamber. This arrangement permits a close coupling between the work coil and the load, which then provides a good flexibility for adjustments of coil dimensions, for controlling the amount of levitation needed for stable operation at a given power level. An overall view of the melter is shown, with the melt-chamber door open, in Fig. 1. The radiation shields surrounding the single-turn induction coil are of water-cooled copper. The chamber is stainless steel, as are most of the components within the chamber. The control panel for the scanner is located at the immediate lower right of the melt chamber. This panel controls the operation of the scanner. The operations controlled are the interface rotation rate, the stretch-squeeze or diameter control, the up and down scanning speeds, and the induction power. All of the drive motors are constant-torque variable-speed motors. The scanning speeds are set with precision helipots and continuously observed with the voltmeter on the control panel and checked with a mechanical indicator within the melt chamber. The rotation rate is also set with a precision helipot. The up-scanning speeds are 2 to 300 in. per hr.

Jan 1, 1963

By J. H Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. H. Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By James S. Foster, Paul G. Shewmon, Frank V. Nolfi

Analytical expressions are developed for the kinetics of dissolution or growth of a spheroidized, solute rich stoichiometric Precipitate in the surrounding matrix. There are two limiting cases; in one the rate of dissolution or growth is limited by long range solute diffusion through the matrix and in the other by the transfer of atoms across the mrdrix-precipitate interface. In the former case local interfacial equilibrium exists while in the latter it does not and the rate of dissolution or growth is controlled by an interfacial reaction. The analysis treats both limiting cases as well as mixed control in a single development, where it is found that the thermodynamic state of the interface is completely specified by a single parameter, o, defined by where K is the reaction rate constant, D is the matrix solute diffusivity, and R, is the precipitate radiz~s. If K is infinite then a is zero and local equilibrium prevails; if K deviates infinitesimally from zero, then a is very near unity and an interfacial reaction is rate controlling. Mixed control occurs for intermediate values of o. From the analytical results, numbers are computed which are useful in determining the duration of interfacial reaction or mixed control; following this time period, long range diffusion is rate controlling. THE rate controlling process or processes governing phase boundary migration has been the subject of much speculation and investigation. Traditionally, the most widely assumed boundary condition in quantitative treatments of this problem has been that of local interfacial equilibrium. This condition implies that long range diffusion of one or more elements controls the migration and is referred to as "diffusion controlled migration" (herein DCM). In contrast to the above view is the proposition that local interfacial equilibrium does not exist and that transport of atoms across the interface is rate controlling. Consequently, this mechanism is referred to as "interface controlled migration" (herein ICM). In processes of the latter type, the activity, a, of one or more elements is discontinuous at the phase bound- ary and the flux, J, across the boundary of a given element is some function of its activity discontinuity, a. One of the most comprehensive contributions to a mathematical description of phase boundary migration is due to am.' His analyses are applicable to precipitation in binary systems in which a) the precipitates are spherical* solute rich compounds of constant

Jan 1, 1970