Search Documents

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By J. J. Forbes

'"THE Federal Coal Mine Safety Act (public Law T. 552. 82nd Congress) was approved oil July 16, 1952. It incorporates, as Title I, the Coal Mine Inspectio1.1 and Investigation Act of May 7. 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter. coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title 11 contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires. inundations. and man-trip 01. man-hoist accidents. At this point a brief account of events that preceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Govermment as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coalmine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small folce of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations aftel mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia. Ill., disaster of March 25. 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act. The act is a compromise measure. Senator Matthew M. Neely of West Virginia and Congressman Melvin Priec of Illinois introduced almost identical versions in the 82nd Congress, but they were considered too drastic. The final version was introduced by Congressman Samuel K. McConnel, Jr., of Pennsylvania, after considerable discussion and amendment in committee hearings. It was passed by the Congress and became effective when signed by the President on July 16, 1952. The act is somewhat limited in scope because it applies only to approximately 2000 coal mines in the United States and Alaska that employ regularly 15 or more individuals underground. It exempts approximately 5300 mines employing regularly fewer than 15 individuals underground and all strip mines, of which there are about 800. Moreover, it covers only conditions and practices that may lead to major disasters from explosion, fire, inundation, or man-trip or man-hoist accidents. According to Bureau records, such accidents have resulted in less than 10 pct of all the fatalities in coal mines. It is important to mention that the law is not designed to prevent the day-to-day type of accidents that have caused the remaining 90 pct or more of the fatalities, because it was the specific intention of the Congress to reserve the hazards which caused them to the jurisdiction of the coal-producing states. Many who opposed any Federal legislation that would give the Federal inspectors authority to require compliance with mine safety regulations claimed that such legislation would usurp or infringe upon States' rights. To assure that the principle of States' rights would be preserved, the act provides for joint Federal-State inspections when a state desires to cooperate in such activities. The Director of the Bureau of Mines is required by the act to cooperate with the official mine-inspection or safety agencies of the coal-producing states. The act provides further that any state desiring to cooperate in making joint inspections may submit a State plan for carrying out the purposes of this part of the act. Certain requirements are listed: these must be met by a state before the plan can be accepted. The Director of the Bureau of Mines, however, is required to approve any State plan which complies with the specified provisions. The Director may withdraw his approval and declare such a plan inoperative if he finds that the State agency is not complying with the spirit and intent of any provision of the State plan. When this paper was prepared, agreements for joint Federal-State inspections had been entered into with Wyoming and Washington. A few other states have indicated their desire to submit a State plan and negotiations toward that end are now under way. Reluctance to enter into such agreements may be due to the mine operators' knowledge that in the states that adopt a cooperative plan they are prohibited from applying to the Director of the Bureau of Mines for annulment or revision of an order issued by a Federal inspector and must appeal directly to the Federal Coal Mine Safety Board of Review for such action. Experience has proved that review by the Director as provided in the act is a less expensive and time-consuming procedure to all concerned than applying to the Board. Reluctance also may stem from the fact that joint Federal-State inspections somewhat restrict the movements of the State mine inspectors and tend to reduce the number of inspections of mines. Where a State plan is not adopted, the Federal coal mine inspector is responsible under the law to take one of two courses of action if he finds certain hazardous conditions during his inspections. The first action involves imminent danger. If a Federal inspector finds danger that a mine explosion, mine fire, mine inundation, or man-trip or man-hoist accident will occur in a mine immediately or before the imminence of such danger can be elim-

Jan 1, 1955

By L. A. Rapoport, W. J. Leas

The original Burkley-Leverett theory has been extended and a more detailed formulation of the waterflood behavior in linear horizontal systems is presented. Particular consideration has been given to the evaluation of capillary pressure effects and differential equations permitting an explicit evaluation of these effects have been derived. On the basis of the developed theory it is recognized that the flooding behavior is dependent upon the length of the system and the rate of injection. At the same time it has been determined that systems of different lengths yield the same flooding behavior if the injection rates and or the fluid viscosities are properly adjrrsted or "scaled." It has also been found that the sensitivity of the flooding behavior with respect to rate and length decreases as any one of these {actors increases in value and that for sufficiently long systems and high rate.; of water injection the flooding behavior becomes independent of rate and length. or "stabilized." To such stabilized conditions the theory formulated by Buckley and Leverett is applicable. A number of laboratory flooding tests have been made and good agreement Iraq been found between theory and experimental observations. The experimental results are discussed and it is shown that under field conditions the flooding behavior is usually stabilized. As a result of these finding; a procedure is indicated for evaluating field performances either on the basis of tests performed with commonly available core samples or by means of calculations using relative permeability data INTRODUCTION In recent years the development of methods for evaluating oil recovery by waterflooding has been the object of considerable research. A theoretical analysis of the mechanisms involved in the displacement of immiscible fluids was originally established by Buckle!- and Leverettl and experimental investipatio~~s have been made by numerons workers." Many of the experimental results are in mutual agreement and bear out several significant features of the flooding mechanism as predicted by theory. Thus it lias been generally recognized that a flood corresponds to the movement of a steep saturation hank or "front" (primary phase), followed by additional gradual oil displacement (subordinate phase). It has also been found that for any porous medium the flooding behavior is largely dependent upon the oil-water viscosity ratio and that for increasing values of this ratio the relative importance of the primary displacement phase decreases while that of the subordinate phase becomes more pronounced. Although the studies to date have clarified certain aspects of the flooding process. they have given rise to observations of a somewhat contradictory nature that cannot he explained in terms of the original theory. These observations pertain mainly to the effect of injection rate or pressure gradient upon recovery. Some investigators report laboratory tests that indicate incresing oil recoverieq with increasing rates of water injectill, others find the flooding behavior to be independent of and other. mention lower oil recoveries with increased injection rates.3 The conflicting evidence indicated above creates considerable uncertainty with respect to laboratory testing procedures and the utilization of the resulting data for field evaluations. The principal purpose of this paper, then, is to resolve these Uncertainties by means of a comprehensive theoretical and experimental investigation of the flooding meanism. THEORETICAL DEVELOPMENT Derivation of Flooding Equations The mathematical description of transient flow phenomena is based upon the consideration of the various processes occurring during an infinitesimal time interval in an infinitesimal volume element and upon the correlation of these processes with those occurring in the adjacent elements. The volume elements are defined as being infinitesimal in comparison to the overall dimensions of the porous system, yet each sufficiently large so aS to encompass the full range of pore openings encountered throughout the system. If a porous system can arbitrarily be subdivided into an infinite number of volume elements all possessing the same distribution of pore openings and if this distribution is unformly continuous. the system may be said to be homogeneous. Such a homogeneous porous medium is considered in the present studivs. It is furthermore postulatecl that only oil and water are present in the pornu wediu. that they act a- totally incompressible and immiscible fluids. and that gravity effects are negligible. In n linear flow system of unit cross sertional area. as treated here. the infinitesimal volume element.; to he considered are cylindrical ".slices" of thickness dx. oriented perpendicularly to the direction of flow. The equations applicable to any such volume element. at my time. describe the movement. of oil and water across the element:

Jan 1, 1953

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By R. D. Taylor, Jim Douglas Jr., H. H. Rachford Jr., P. M. Dyke

A major obstacle to the use of wetting agents in .secondary recovery by water flooding is the adsorption of the agents on the sand. As a result of adsorption, the surfactant always lags behind the floodwater front. Consideration of the chromatographic theory of adsorption indicates that the detergents will not lag as much if used in very high concentrations. An investigation was made of the possibility of using high concentrations economically by flowing slugs of wetting agents followed by normal flood water. The experiments consisted of adsorption studies on Alundum powder and Berea sandstone. Flow rests on a 12-in. Alundum core and 22-in. Berea core were used to determine rate of detergent movement. The results of the flow experiments indicate that the relative rate of surfactant advance is, indeed, sensitive to the concentration of the agent. A 10 per cent slug moved with a rate that war 78 to 95 per cent as fast as the rate of advance of the flood water. By contrast, one with 25 ppm (the number of parts of commercial detergent in a million parts of water on a weight basis) concentration moved less than one-fourth as fast as the flood water, and calculations indicate that in very long porous systems the rate of movement of the lower concentrations will be a small fraction of the rate of advance of the flood front. The results. of the adsorption studies were utilized to calculate the rate of advance of the detergent when only the initial concentration was known. The calculated rates showed substantial agreement with the experimental flow tests in the high concentration ranges. The adsorption results were also used to estimate the cost of the materials for a slug-type surfactant flood in the field. In addition to the faster rates of movement, the concentrated detergent slugs removed much more oil than the dilute solutions. However, the effectiveness of the slug process depends on many variables. The quantity of oil removed is increased markedly by increasing the flooding rate. The efficiency is also influenced by the type of crude, type of reservoir rock and initial water saturation. Therefore, a careful analysis of each reservoir system is required before the economic value of the process can be determined. INTRODUCTION It is well known that the displacement of oil by invading water during water flooding is far from complete. It is generally agreed that the unrecovered oil is retained in the porous medium by the capillary forces which may be relatively large compared to the forces generated by the flowing water. Therefore, it was logical that some early workers should turn to surface-active materials to reduce the capillary forces to facilitate the release of oil. As early as 1927,' a patent was granted for the use of surface-active materials in water flooding. In 1932, when soap solutions were passed through Bradford and Venango sands, it was reported that the results were inconclusive, erratic and that "further investigation is needed to determine exactly the function of the solution and to obtain a clearer insight into the phenomena involved."' Some of the modern scientific reports conclude with a similar statement,' showing that the lack of agreement on the mechanism of oil removal by wetting agents is still very widespread even though several comprehensive studies have been reported.'." Although there is a lack of agreement as to the general effectiveness of the detergents for water flooding, most investigators do agree that all of the common detergents are strongly adsorbed onto the solid surfaces of the reservoir. In the early calculations it appeared that all additives would be lost before reaching much of the formation area which contained the additional oil to be removed. Experiments indicated that if the usual small waterflood concentrations of wetting agents were used, the rate of advance of detergent through the formation would be only a small fraction of the rate of advance of the flood front. Indeed, some investigators4 felt that the use of wetting agents would never be economically feasible because of their adsorption. For example, DunningG estimated that the wetting agent in concentrations of 25 ppm, would advance only 0.05 times as fast as the flood front. Ojeda, et al,' found that a surfactant in a concentration of 10 ppm moved less than 0.01 times as fast as the flood front. It is significant, however, that both investigators found that increased concentrations of wetting agents moved faster, relative to the flood front, than solutions at the lower concentrations. Ojeda showed that an extrapolation of his data indicated a relative rate of 0.5 at 1 per cent concentration, while Dunning6 estimated a relative rate of 0.46 for a 1 per cent concentration. It was obvious that these concentrations could not be used for continuous injection because the cost of the injected detergent would far exceed the value of additional oil produced. Traditionally, detergents are used in very low concentrations for they show good

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country's production. The largest previous year's consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By David R. Mitchell, Byron M. Bird

THE revision of this chapter has presented a problem in that heavy-medium jigging has come into the picture since the chapter was originally written (seven years ago), a practice in which an artificial medium is built up and maintained in the jig circuit. As this development makes the jig a "true" heavy-medium process, the method belongs in the chapter dealing with such processes. Although putting this development in its proper position in the book involves some repetition, this seems to be the best procedure, and it has been followed. As the chapter on jigs in its original form was intended to be more or less a handbook on jigging for the use of the practical man, and the great bulk of the material therein is still generally applicable, the text has been re-used in large measure. Two major changes should be noted: (1) the portion of the text relating to the refuse-withdrawing mechanism of the McNally-Pittsburg jig has been entirely rewritten, and (2) a description of the hutch valves on the Jeffrey jigs has been added. Jigging is the stratification of a mass of solid particles in upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through 3/4-in. to 0, and mixed sizes of ores down to 7/32-in. to 0and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems.

Jan 1, 1950

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By B. Trentini

In the spectacular development of pure oxygen steel-making, the process using the vertical lance converter LD, is at the present time the most widely employed. Proper control of slag composition during the steel-making process appears to be essential in achieving satisfactory blowing from both the metallic yield and metallurgical points of view. The paper illustrates the primary importance of the presence of a large quantity of metal droplets in the slag during the process. In the case of both phosphorus and hematite pig iron, it can be deduced from the phase diagrams and confirmed by experimentation that nonhomogeneous slags are one of the causes of slag overflowing during the blow. The problem is however a complex one and further physicochemical studies appear necessary. Finally, the new continuous steelmakingprocess developed by IRSID is described. PEOPLE who knew Henri Marion Howe have said that he took great pleasure in speculating on the future of metallurgical processes. It is therefore not inappropriate to devote, in his memory, some description and discussion to processes unknown to the world of his time, in particular oxygen steelmaking and continuous steelmaking. The first industrial application to steelmaking of tonnage oxygen produced by air liquefaction was made in Germany just before the war and consisted in enriching the air blown through the bottom of a basic Begsemer converter in order to melt a higher proportion of scrap and to produce steels with lower nitrogen content than is achieved with conventional practice. While this process was being developed after the war, mostly in Western Europe, steelmakers were becoming increasingly familiar with the technique of blowing pure oxygen from the top, first by means of consumable steel pipes, with or without refractory shielding, and later by water-cooled lances, designed for the purpose and affording longer life. The field was then open for the wide use of pure oxygen in steelmaking, either in existing processes such as open-hearth or electric furnace, or in new processes. These new processes can be broadly classified according to the category of furnace employed. In the case of the vertical converter taken as the first category, bottom-blowing of pure oxygen causes extremely rapid wear of the refractory tuyeres, and although various expedients have been tried to overcome this drawback (such as mixing oxygen with CO2 or H2O or using high pressure oxygen), they have had to be abandoned. The solution for vertical converters has been found in top-blowing with a vertical water-cooled lance; this is known as the LD process or basic oxygen converter process.

Jan 1, 1969

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By F. J. Radd, R. L. McGlasson

The mechanisms of corrosion and corrosion fatigue damages to sucker rods are examined from a fundamental electrochemical viewpoint, and the relationships of sucker rod microstructures to these damaging effects are defined. The common corrosive agents in crude oil production and storage are discussed as to types of attacks that they cause. The variations of fatigue strength with alloy content, surface preparation, and stress ranges are analyzed. Finally, conclusions are drawn as to how microstructures largely influence and control sucker rod performance. INTRODUCTION Greater than 90 per cent of the crude oil produced by artificial lift methods is produced through sucker rod pumping systems. In the USA each year more than $14 million is spent for sucker rods in new and old pumping installations. It is important to make this investment a wise one. Essentially, the sucker rod system is a long series of steel rods, operating under alternating stress loadings and under mechanical vibrations, which connect the surface power source with the subsurface pump. These rods often operate in a variety of corrosive media, including water, brines, carbon dioxide, hydrogen sul-fide, and air. Basically, this paper is concerned with the problem of the behavior of certain steels in various corrosive media under high and dynamic stress patterns. The main objective of this paper is to show how, once the stress effects and the corrosive environments are defined, one can still realize structural control and beneficial influence upon corrosion and corrosion fatigue. FUNDAMENTAL DEFINITIONS AND ANALYSIS In the corrosion and stress behavior of this solid state mixture of iron and iron carbide called steel, one must analyze upon what major factors does its service life depend and of what, exactly, is steel composed. The former question can be referred to two external factors and two internal factors. The two major external factors are: 1. the nature of the stress patterns — size and range of stresses present 2. the nature of the corrosion — erosion environment — the corrodent and/or wear involved The two fundamental internal factors that govern the strength and useful life of a steel both in normal duty and in heavy-duty corrosion service are: 1. the nature of the steel volume properties 2. the nature of the steel surface properties For the latter question normal steel is defined as a solid mixture of iron and iron carbide particles, generally with certain accidental and intentional elements present. (The amount of iron carbide present is determined by the carbon content of the steel.) These additional elements generally dissolve into either the iron (ferrite) or the iron carbide (cementite) components.

Jan 1, 1955

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By D. K. Crampton, H. I. Burghoff, J. T. Stacy

The effect of cold-working upon electrical conductivity of copper and of copper alloys appears not to be generally known in detail. Although several papers on the subject have been presented, showing variable effects according to alloy composition, it is often assumed that the 2 to 3 per cent lowering of the conductivity of ordinary tough-pitch copper by severe cold-working is typical for copper alloys. Because of this situation it was decided to carry out the present work upon several types of copper, copper-zinc alloys over the commercial range of brasses, other binary alloys, and numerous age-hardening alloys in the quenched, and quenched and aged conditions. The large number of alloys investigated made it impossible to study every one in the detail it may have merited. Inasmuch as several interesting points that could not be satisfactorily explained came to light, further work is contemplated by the authors. It is usually considered that the normal effect of cold-work on ductile metals and unordered alloys is to decrease conductivity slightly. In alloys that are in the ordered state, as annealed or otherwise heat-treated, cold--working tends to disorder the structure, resulting in very marked lowering of conductivity. The random state of atomic arrangement produces lower con- ductivity than the ordered state for the same composition.1 Previous Work Previous work in the authors' laboratory has shown the electrical conductivity of several copper alloys to be decreased by greater amounts than might have been expected, in view of the general knowledge on the subject, when cold-worked. Guillet and Ballay2 investigated the influence of cold-work upon the resistivity of several metals and alloys, including copper and some copper alloys. The increase of resistivity due to severe working w is less than 4 per cent for all pure metals tested, while the increases for the alloys were generally higher. In the copper-zinc alloys, they found that the increase of resistance due to drawing increased with zinc content, and reported a 21.7 per cent increase of resistance for an alloy contaiiiing 67.9 per cent Cu as severely worked. Masima and Sachs3 studied the change in electrical resistance of three brass crystals when stretched in the tensile test, obtaining increases in resistance of the order of 3 per cent for 30 to 40 per cent reduction of area of the specimens. The resistance decreased again when the cold-worked crystals were subsequently annealed. Bardenheuer and Schmidt4 found that the conductivity of copper was decreased by 3 to 4 per cent when reduced 50 per cent by working. The conductivity of 72-28

Jan 1, 1941

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By S. Floreen

Measurements have been mode of the effects of tempering and austenitizing heat treatments, the work-hardening characteristics, and the effects of test temperature and strain rate on the properties of a low-carbon Fe-18 pet Ni martensitic alloy. In many respects the alloy behaved quite similarly to cold-worked iron. One notable quality was the excellent ductility at temperatures as low as 20°K. Many of the qualities of the maraging steels could he related to the properties of the Fe-Ni matrix. THE 18 pet Ni maraging steels have demonstrated that unusual combinations of strength and toughness may be obtained by age hardening a low-carbon Fe-Ni martensite matrix.' These properties must, to some extent, reflect the properties of this Fe-Ni matrix, and therefore an understanding of the properties of this matrix is a prerequisite to a complete understanding of the steels. There have been several recent studies of Fe-Ni-C martensites, but not much attention has been paid to alloys with very low carbon contents. At low carbon levels the crystal structure of these alloys is essentially bee.2 Electron transmission microscopic examination of a 20 pet Ni binary alloy showed martensite platelets separated by low angle boundaries.3 Plastic deformation of the low-carbon alloys has been shown to proceed by wavy glide.4 The hardness of these martensites is typically RC 28, and their yield strengths are 70 to 80 kg per sq mm.2, 5 Their ductility is excellent. Room-temperature tensile elongations of 18 pet and reductions of area of 70 pet have been observed in an Fe-18 pet Ni binary alloy.5 These observations have provided a qualitative understanding of the flow characteristics of these alloys. To date, however, no thorough study of their properties has been made. In particular, it is not known to what extent the deformation characteristics of low-carbon martensites are similar or dissimilar to those of pure iron or other bee metals. The present work was undertaken to provide more detailed information on the flow characteristics of a low-carbon Fe-18 pet Ni martensite. PROCEDURES, RESULTS, AND DISCUSSION Materials. A 40-lb heat of the Fe-18 pet Ni alloy used in this study was made by vacuum-induction melting. The charge materials were electrolytic iron and electrolytic nickel. A carbon boil was used to achieve deoxidation. After the boil the heat was refined by additions of 0.1 wt pet Ti and Al. These additions are commonly used in the maraging steels to keep the carbon and nitrogen contents in solid solution at a minimum. After casting, the heat was

Jan 1, 1964

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949

By Burton H. Boyum

Greater depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Mar-quette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock. Introduction The deflection of diamond drill holes by wedging was a widespread practice in Canada, South Africa and the Lake Superior District as early as 1907 to 1920. Several basic schemes were used, with local variations.' The deflecting wedge assembly was the idea of Mr. Welldon and Mr. Payne-Gallwey operating under the supervision of Mr. William Gallagher of Johannesburg, South Africa. All schemes employed some means of plugging the old hole. A footpiece of various styles was placed in the hole on the plug. In some methods, the orientation of this piece was determined before placing the deflecting wedge. Some techniques permitted continuing the hole the same size after wedging, while others necessitated a size reduction. Interest in wedging diamond drill holes in the Lake Superior District waned after 1920. The Hall-Row patented system for deflecting holes was developed in Canada about 1918.2 Interest centers on the wedging process for the following applications: 1. Maintaining a given course and inclination of the drill hole. 2. By passing an obstruction in a drill hole. 3. Resampling an ore body. 4. Exploring an area overlain by surface conditions not favorable to drilling. During the period of 1913 to 1920, The Cleveland-Cliffs Iron Co. used the wedging technique under a variety of conditions. In general, the practice was not applicable again until 1946. Meanwhile the Hall-Row system of drill-hole deflection survived years of application as the best technique available. In the intervening years, our depth of exploration has increased as well as the overall cost of drilling. As exploration becomes deeper, there is the possible economy of cutting the ore body at a moderate distance from the parent hole without redrilling from surface. Thus a branch hole started near the mid-point of a deep hole can reach the ore horizon at a considerable offset from the parent hole. This permits a greater interval between surface drill holes as drilling becomes deeper. Our interest revived in the subject and a wedging program was initiated. General Description Results The maximum theoretical angular deflection possible, based on the deflecting

Jan 1, 1949