Search Documents

By P. R. Sperry

In an investigation of the decomposition of the solid solution in a cold worked high-purity aluminum alloy containing 7 pct Mg, aged at temperatures from 30o to 82°C, the nucleating sites at the earliest stages of precipitation were observed to be of two types. Nucleation occurred at the high angle grain boundaries both when the alloy was initially cold worked and when solution annealed. Nucleation also occurred at certain unique deformation markings which began to appear in abundance at approximately 30 pct reduction in thickness by cold rolling. These deformation markings were identified as deformation (kink) bands rather than as the usually assumed "slip planes." Zn material that was cold rolled 15 pct, only the grain boundary Fig. 2—A1-7 pct Mg alloy, cold worked 60 pct and heated at 230° C for 5 min. Etched with Perryman's reagent. X500. Reduced approximately 25 pct for reproduction. (a) Bright field illumination, precipitate deeply pitted. (b) Phase contrast, showing slip markings.

Jan 1, 1962

By G. K. Dumbauld, B. E. Morgan

A satisfactory well-cementing composition must retain its fluidity long enough to be pumped into Place; then it must develop within a reasonable length of time sufficient strength and impermeability to anchor the casing in position and to form an effective seal between the casing and the formations. These properties may be evaluated by pumpability, strength (compressive or tensile), and permeability tests. Laboratory test procedures for the determination of pumpability time and strength development have been outlined previously and are readily available,1 but a satisfactory and convenient laboratory procedure for the measurement of the permeability of set cement has not been developed heretofore. some permeability data have been obtained previously by passing air through dried cement specimens.2 such a procedure is unsatisfactory because the drying of set cement alters it physical and chemical properties and subjects it to conditions dissimilar to well conditions. A more realistic method would be one wherein the cement remains water-saturated durin

Jan 1, 1952

By David Hall

IN October, 1926, the Inspiration Consolidated Copper Co. began the operation of its new leaching plant, which has a capacity to handle 8600 dry tons of ore daily and produce therefrom approximately 160,000 lb. of electrolytic copper per day. (See Fig. 1.) The energy for the leaching process is supplied by three motor generator sets (Fig. 2), each set consisting of one 5450-hp., 6600-volt, three FIG. 1.-LEACHING PLANT OF INSPIRATION CONSOLIDATED COPPER CO. AT INSPIRATION, Ariz. phase, 25-cycle, 500-r.p.m. synchronous motor and two 1920-kw., 150 to 320-volt, 6000-amp.,12-pole, d. c. generators, and one 70-kw., 125-volt d, c. exciter. The capacity of the three sets is 36,000 amp. at 320 volts. A description of the metallurgical processes of this plant was. given in a paper by H. W. Aldrich,1 and from his paper we quote the following figures for the month of July, 1927:

Jan 1, 1928

By R. H. Singleton

ThE purpose of this investigation was to determine the effect of cerium upon the nonmetallic inclusions found in cast and wrought steel containing various amounts of sulfur, oxygen, and nitrogen. Interest of the Physical Metallurgy Laboratory of the Watertown Arsenal Laboratories in this type of research was stimulated by the reports from industry that rare-earth metals imparted beneficial effects upon the mechanical properties of steel, but that the mechanism was not understood. Berry and Dorvel' found that misch metal improved the impact properties of aluminum-killed cast steels. They reported that the rare earths modified the intergranular-film type nonmetallic inclusion, present with aluminum as the sole deoxidant, to a randomly distributed globular type. Lilliequist and Mickelson2 observed the improvement of ductility and toughness of quenched and tempered cast steels through rare-earth additions. They also observed the change from angular to duplex inclusions when rare earths were present. They con-

Jan 1, 1960

By H. W. McCue, Henry Rogatz

Oil.—In the Texas Panhandle, during the year of 1941, 647 oil wells were drilled with a total daily initial production of 133,435 bb1.—that is, 145 more oil wells than in the previous year, with a decrease in total daily production of 5752 bbl. On Dec. 31, 1941, a daily allowable of 116,766 bbl., which was an increase of 27 per cent over 1940, was assigned to the field to be produced from 5182 wells. The total amount of oil produced for the year was 27,904,846 bbl., making a cumulative total of 404,657,324 bbl. during the past 20 years. Gas.—During the year, 52 gas wells were drilled, having a combined open flow of 2.62 billion cu. ft. per day—that is, 40 less than the number of wells drilled in 1940, with an increase in the open flow of 217,100,000 cu. ft. per day. The gas

Jan 1, 1942

By Henry Rogatz, H. W. McCue

Oil.—In the Texas Panhandle, during the year of 1941, 647 oil wells were drilled with a total daily initial production of 133,435 bb1.—that is, 145 more oil wells than in the previous year, with a decrease in total daily production of 5752 bbl. On Dec. 31, 1941, a daily allowable of 116,766 bbl., which was an increase of 27 per cent over 1940, was assigned to the field to be produced from 5182 wells. The total amount of oil produced for the year was 27,904,846 bbl., making a cumulative total of 404,657,324 bbl. during the past 20 years. Gas.—During the year, 52 gas wells were drilled, having a combined open flow of 2.62 billion cu. ft. per day—that is, 40 less than the number of wells drilled in 1940, with an increase in the open flow of 217,100,000 cu. ft. per day. The gas

Jan 1, 1942

POSITIONS VACANT (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) General manager .for a pyrite mine in Virginia, with experience in the mining and particularly in the washing of pyrite, required. Salary at start, $250 per month with perquisites. No. 28. Assayer and cyanide man for a Costa Rica plant. Salary $100. No. 29. Mine manager to develop gold-mining property in Witwatersrand, Transvaal. Salary £2,000 to £4,000, according to the experience and ability of the engineer. No. 31. Mine superintendent for a mine in Arizona containing copper, gold, silver ore. Will have entire charge of operation and development. Salary to start, $200 per month with perquisites. No. 32. .Mining engineer to make complete report and suggest necessary machinery for development and operation of a placer property; also to examine a copper property. Both properties in Peru, South America. No. 34.

Jan 4, 1915

The Bureau of Mines extends. a cordial invitation to all members of the Institute to visit Pittsburgh, Sept. 29 to Oct. 1, to participate in the dedication of the Mines Experiment Station. Accompanying this will be a nation-wide participation in a First-aid and Mine Rescue Contest. The Pittsburgh Chamber of Commerce will cooperate. The Institute will be represented by a special delegate appointed by the President. MONDAY 8:30. A. M. Bureau Building open for inspection. 10:30 A. M. Dedicatory Ceremonies in rear of Main Building, .4800 Forbes St. 2:00 P. M.. Special Train and Automobiles to Experimental Mine near Bruceton, Pa. 3 to 6 P. M. Mine Explosion and Inspection of Experimental Mine . and of Explosives Testing Plant near Bruceton, Pa. 6:00. P. M. Return by Special Train and Automobiles to B. & 0. Station, Pittsburgh. 8:00 P. M. Informal Reception and Organ Recital Carnegie Music Hall. Arranged by Carnegie Institute of Technology.

Jan 9, 1919

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THESE furnaces are of the ordinary Siemens type, and present no special peculiarities of construction. The bed of each is 8 feet by 20 feet clear inside of the walls and ports. The producers are placed at a distance of about 200 feet from the furnaces, and the gas is collected in an iron tube and led across the yard overhead. It then drops underground into the gas flue, and is distributed to the furnaces. A considerable weight of floor-plates over the valve-pits is included in account 39, but none of the general stock of floor-plates for the mill were charged to the furnaces. In Table No. 1 is shown the money cost of the furnaces as distributed to the several accounts named. In Table 2 is shown the proportion of each account due to each of the several items or classes of expenditure named.

Jan 1, 1878

Michigan State Department of Conservation, Lansing, Mich The Department of Conservation has two divisions issuing publications which should be listed in this directory. Geological Survey Division. R. A Smith, State Geologist Land Economic Survey Division L R Schoenmann, Head. A price list of publications of either division will be sent upon request to that division Geological Survey Division.-Citizens of Michigan may obtain publications of this Division on payment of forwarding charges Prices to others for available publications are given below: Vol 5 (1881-1884): Pt 1, Geological report of the Upper Peninsula of Michigan, by L L Hubbard, pt 2, Geology of Lower Michigan with reference to deep borings, by A C Lane, $125. Annual Report for 1908. Pt b, Geological section of Michigan, by A C. Lane and A E Seaman, 50 cents. Publication No 5, The Late Glacial and Post Glacial Uplift of the Michigan Basin, and earthquakes in Michigan, by W. H

Jan 1, 1933

By P. J. Potter

PRACTICALLY all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specificational limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings.

Jan 1, 1929

By N. L. Svensson

The model developed by Tuylor for the calculation of Polycrystalline yield strength has been applied to the case of an aggregate hawing a preferred orientation. In general this procedure requires the specification of texture by means of weighting factors applied to specific orientations. The problem to which the model has been applied is that of the yield-strength aniso-tropy of cold-rolled aluminum whose rolling texture was described as a combination of (110)[112] and (311) [112] In this case yield-strength anisotropy is defined by the rutio of yield strength measured at an angle 8 to the rolling direction to that measured along the rolling direction. The method of calculation of yield-strength ratio as a function of ? is described and the results show good agreement with experimental values. The orthotropic yield criterion suggested by Hill has been applied to the results and the strain ratio R also calculated as a function of ?. This has been compared with calculations using the method suggested by Elias, Heyer, and Smith which does not exhibit suck good agreement with observation. one deficietlcy of the method presented is that the strain ratios used by are those applying to iso-Irobic materials. The method should therefore be reg-clrded only as a first abbroximation to the prediction of anisotropy. THE problem of calculating the stress-strain characteristics of polycrystalline aggregates from the properties of single crystals has attracted attention for a number of years. The most important contributions to this study have been those due to: Sachs,' Cox and sopwith,2 Taylor,3 Kochendorfer,4 Batdorf and Budiansky,5 Calnan and Clews,6 Bishop and Hill,7,8 Kocks,9 Budiansky, Hashin, and sanders, 10 Kroner,11 Cyzak, Bow, and payne, 12 Budiansky and Wu,13 and Lin.14 While the earlier work has been largely superseded, recent developments tend to support Taylor's solution" within the restriction imposed by his assumptions. The essential features of Taylor's approach were: 1) the material is rigid-plastic; 2) each grain experiences the same strain components as the aggregate as a whole (the problem was that of uniaxial deformation with principal strain components in the ratio 3) all regions of each grain deform uniformly; 4) work hardening occurs equally on all slip systems. While Bishop and Hill7 have generally validated this approach, there has been some criticism offered. Kocks? as pointed out that since multiple slip must occur the single-crystal data must be determined from orientations arranged such that polyslip takes place. Boas and Hargreaves,15 and others, have shown experimentally that the strain distribution within grains is not uniform, the strains in the vicinity of grain boundaries being less than those in the center of the grains. Both of these criticisms can be largely offset by the suitable choice of single-crystal critical shear stress. However, for the problem analyzed below, the critical shear stress is not directly used and, consequently, these criticisms lose their importance. The more recent contributions have attempted to obtain a more complete analysis by considering an elas-toplastic material and considering interactions between grains of differing orientations. Lin14 has considered the early stages of yielding for a polycrystalline aggregate having specific regions of defined slip plane orientations. On the other hand, Budiansky and Wu13 have allowed for these interactions for randomly disposed grain orientations and have calculated the polycrystalline stress-strain curves for crystals exhibiting either elastic-ideally plastic or kinematic hardening characteristics. This work has shown that yielding commences when the macroscopic stress is 2.2 times the critical shear stress for slip in a single crystal (7,). The yield stress-strain curve then rises becoming asymptotic to a value of 3.072 7,. This is close to the value obtained by Bishop and Hill (3.06) in their confirmation of Taylor's method. This, of course, is to be expected since, at large strain values, the elastic strains are negligible and the rigid-plastic model is satisfactory. The results of Budiansky and Wu indicate that the result obtained by Taylor is 7.7 pct high at a plastic strain which is two times the elastic strain at the initiation of yield. By defining the anisotropy in terms of relative values, the ratio of yield strength at orientation ?, to that measured in the rolling direction, the effect of the discrepancy in Taylor's solution is considered to be of lesser consequence. Therefore, it is anticipated that an analysis based on Taylor's solution, which can be quite straightforward, should provide a reasonable estimation of the anisotropy of materials having a preferred orientation texture. OUTLINE OF TAYLOR'S METHOD In fee metals there are four possible slip planes (the octahedral planes) and in each there are three possible slip directions (the edges of the octahedron), that is a total of twelve possible slip systems. von Mises16 has shown that at least five independent slip systems must become operative in each grain of the polycrystalline aggregate in order to preserve continuity of strain. With this geometrical requirement as basis and the assumptions previously listed, Taylor determined the operative slip systems for a number of orientations of the tensile stress axis specified in the unit stereographic triangle. For the ith slip system, the critical shear stress

Jan 1, 1967

In 1974, iron pellet production in the Great Lakes region reached the 53-million-tpy level, accounting for more than 88% of the nation's pellet production. By 1978, pellet output from the Great Lakes district will climb to at least 78 million tpy. To achieve this 50% increase in output, the US iron and steel industry is investing at least $1.25 billion in new mines and pelletizing plants, mostly in Minnesota and Michigan. The biggest effort is concentrated in the Mesabi Range of Minnesota, the heart of the US steel industry's major iron ore source: here, plans for two new taconite plants-one by Hibbing Taconite Co., and the other by Inland Steel Mining Co.-and three major expansions of existing facilities are already under way to boost Minnesota's total iron pellet capacity from the current 41.2 million tpy to 65 million tpy by 1978. The facilities being expanded are those of US Steel Corp. (Minntac operations), Eveleth Taconite Co., and National Steel Pellet Co.

Jan 11, 1975

By Eugene S. Meieran

The effects of methods of crystal growing, wafer sawing, polishing, routine handling, diffusion, and epitaxial growth on the defects in GaAs are reviewed and studied using reflection and transmission X-ray topographic techniques. In general, it was found that boat-grown crystals exhibited fewer defects than Czochralski crystals, although all crystals showed large numbers of precipitates visible when examined in the electron microscope. Mechanical surface treatments such as sawing and mechanical polishing introduce damage to a depth of about 5 µ, most of which can be removed by suitable chemical or chem-mechanical polishing. In addition, defects can be introduced through routine handling of wafers, for example with metallic tweezers. These defects can be quite severe, and have been observed 20 µ below the wafer surface. Defects can also be introduced through diffusion and epitaxial growth. These defects, which include precipitates, growth pyramids, stacking faults, dislocations, and so forth, can be detrimental to device fabrication. It is shown that wafers or films which appear defect-free optically can contain defects visible in the X-ray topographs. WHILE the use of GaAs in the semiconductor industry has increased very rapidly in the last few years, due mainly to the recent development of many important GaAs devices,1,2 the major limit to the production of commercial quantities of many GaAs devices remains a severe lack of suitable materials technology. This lack is apparent in two critical areas. First, production quantities of high-quality GaAs crystals, reproducibly doped and precipitate-free, simply are not available commercially, although some reasonable quality material is available on a limited first-come, first-serve basis. Second, in comparison to silicon technology, little is known about the effects of processing variables on the defects either present in as-grown GaAs or introduced through processing and handling of wafers. These areas are now receiving some attention from semiconductor device manufacturers, who are studying defects in GaAs in order to better understand how either to prevent their occurrence or to cope with their existence. Most investigations of the defects in GaAs have been made by optical microscopy3-5 or transmission electron microscopy techniques.'-' Recently, however, the imaging techniques of X-ray topography, electron mi-croprobe analysis, and scanning electron microscopy are being applied to the study of GaAs.9-14 In the case of X-ray topography, a one-to-one image is obtained that must be photographically enlarged. In compensa- tion, the defects within entire wafers may be imaged by simple scanning (Lang technique15) if the wafer is reasonably perfect, or by using the scan oscillation technique developed by Schwuttke16 if the wafer is warped or distorted. The purpose of this paper is to both review and extend the general application of X-ray topographic techniques to GaAs. Emphasis will be placed on the effects of growth and process variables on the quality and perfection of both bulk and epitaxial GaAs. Reference to optical or electron microscopy results will be made when useful. Since the effects on defects of a wide variety of processing variables such as crystal growing, sawing, polishing, diffusion, and epitaxial growth will be somewhat superficially reviewed, a fairly extensive bibliography of the most important recent results in these areas is included. However, for completeness, important defects will be illustrated here, although such defects have been previously shown by others. While this paper is concerned with defects rather than with the physics of X-ray scattering, the mechanisms of contrast formation in the topographs will of necessity be briefly mentioned. EXPERIMENTAL GaAs crystals, both boat-grown18 and Czochralski-grown,'8 containing a variety of dopants of various concentrations, were purchased from outside vendors. Wafers were sliced from the crystals using a Hamco ID saw and were mechanically polished using 1 µ diamond paste. Chem-mechanical polishing was done in bromine-methanol as described by Sullivan and Kolb.18 Chemical polishing was done using a modified sulfuric-peroxide solution, 11 parts H2SO4, 1 part 30 pct H2O2, 1 part DI water.5 Zinc diffusion was carried out in a closed tube, using a 10 pct Zn-In source at 825°C for 1 hr. Oxide masking techniques were used to select the area to be diffused. Epitaxial wafers were either purchased or prepared here. All epitaxial runs prepared here were carried out using a Ga-GaAs-AsC13 source in a closed tube at a substrate temperature of 750°C. Wafers were chem-mechanically polished and gas-etched prior to deposition. The X-ray topographs were taken on a Krystallos Lang camera, operating in the transmission scanning geometry (Lang technique15) or in the reflection scanning geometry (modified Berg-Barrett technique20,21). MoKa, radiation was used for all transmission topographs using a Jarrell-Ash 100-µ spot focus. CuKal radiation was used for all reflection topographs using a General Electric CA-7 1-mm spot focus X- ray tube. Topographs were printed from an intermediate contrast inversion film, so the contrast shown in all figures here is the same as that of the original 50-µ-thick emulsion L4 Iiford nuclear plate used to record the topograph.

Jan 1, 1969

By H. A. Wahl, J. M. Campbell

This study extends our information on solid-liquid slurries to the flow of sand in horizontal fractures. Inasmuch as this is basically an unsteady-state process, a comprehensive photographic study was undertaken in a 10-ft windowed cell to determine if the basic flow regimes described for steady-state flow in pipes applied to the subject process. Since the number of potential variables far exceeds the capacity of a single study, emphasis has been placed on the effects of sand concentration, oil viscosity and oil flow rate. The extensive photographic evidence obtained has proven very valuable in gaining an insight into the basic flow mechanisms. Being able to follow visually the flow characteristics that accompany the quantitative data is valuable in the application of the results. Although the use of dimensionless parameters was carefully investigated. it was found that the data obtained could be more easily, and as accurately, correlated by judicious use of the dimensional variables investigated. However, a study into the feasibility of scaling slurry flow was made in the event this technique is justified in future investigations. The data presented show that the pressure behavior observed in solids transport in pipes basically applies to slurry flow in horizontal fractures. The roles of the parameters are altered but a basic equivalence exists. The most significant correlating parameter was the oil viscosity (µo) and the bulk velocity of the slurry (vn), expressed as ''µv" product. The most significant correlation expresses the rate of advance of the sand as a function of the variables investigated. There are many practical ramifications of this phase of the investigation that should aid in better treatment design. Evaluation of sand advance rates provides a means of estimating sand placement efficiencies during a treatment and the resulting sand distribution in the fracture. The results show that sand placement efficiencies are low under typical treatment conditions. A brief description of the effects of overflushing is also included. INTRODUCTION The flow of sand-oil slurries in fractures is an area in which little basic knowledge is available. This stems to some degree from the fact that it is impossible to duplicate fractures at the surface. They occur in various shapes and sizes with an infinite combination of irregularities. Unfortunately, we can never "see" these fractures except in cores and by indirect means of measurement. In spite of this inherent difficulty, it is desirable to develop some basic concepts that will provide a better understanding of the sand transport mechanism. An insight into the problem is provided by investigations of fluid flow in rectangular conduits. Several studies on the flow of liquids in non-circular conduits1,13 show that a Reynolds number-Fanning friction factor relationship can be written if the hydraulic diameter is substituted for the regular diameter in a circular pipe. This hydraulic, or equivalent, diameter is taken as four times the cross-sectional area occupied by the flowing fluid divided by the wetted perimeter. Eq. 1 expresses an extension of this same work when applied to infinite parallel planes b distance apart.' Eq. 1 is a theoretical equation expressing the friction factor as a function of the Reynolds number for laminar single-phase fluid flow. This expression has been verified experimentally. The equivalent expression for a smooth circular conduit differs only in that the value of the constant is 16 instead of 24. Numerous studies have related friction losses to Reynolds number in both circular and non-circular conduits. These results are widely used and are not reviewed here. Huitt' investigated the effect of surface roughness on fluid flow in simulated fractures. He concluded that fluid flow in fractures may be treated similarly to fluid flow in circular conduits. This work, together with that of Nikuradse,' shows that surface roughness has no appreciative effect upon the resistance to flow in the viscous flow region. In the region of turbulent flow, surface roughness is a prominent factor. Hydraulic conveyance literature is another important source of information. Durand3 has attempted to organize systematically the variables involved in hydraulic-solid transport in pipes. He has classified the modes of flow into three types according to the size of the particles in the mixture— homogeneous mixtures, intermediary mixtures and heterogeneous mixtures. With the usual concentrations and flow rates used in hydraulic transportation, particles with diameters of less than 20 or 30 microns form eszentially homogeneous mixtures with water. The data show, however, that even small materials will tend to settle out under laminar flow conditions. Mixtures containing solids over 50 microns in diameter do not achieve total homogeneity even under turbulent flow conditions. Particles from 50 microns to 0.2 mm in diameter may be transported in fully suspended flow at normal transport velocities although the concentration in the vertical plane is not uniform. Above 2 mm in diameter solid materials are transported along the bottom of the conduit at a velocity substantially less than that of the liquid itself. Between 0.2 and 2 mm in diameter, the particles tend to be in a transition zone between heterogeneous suspended flow and deposit flow at normal hydraulic transport velocities. The sand sizes used in fracturing usually fall in this size range. It is interesting to note that the grain size range designated by Durand for this transition zone corresponds closely to the transition zone between

By R. W. Smith

A study has been made of the crushing and grinding circuits by the Portland Cement Association in nine cement plants. Five of the plants used the wet process and four, the dry method. Both raw and clinker grinding were studied in the four dry processing plants. The raw materials used varied considerably from plant to plant. Actual power consumption data were obtained for the majority of the grinding mills in these plants. Previously representative raw and clinker samples had been obtained from the nine plants, and Bond1 and Hardgrove2 grindability tests were run on these samples. All pertinent data concerning the grinding mills, such as mill size and speed, ball charge size and weight, size distribution of feed, and discharge materials were also obtained. Thus it became possible to calculate the actual horsepower used by the various mills, and to compare this figure to the theoretical horsepower as calculated by several different methods.

Jan 4, 1961

By H. Krueger, H. N. Hersh

USE of autoradiography in diffusion studies offers the advantage that no repeated sectioning is necessary and that the analyses are performed in a simple manner over the continuous range of penetration depths. As part of a program of solid-state physics, it was desired to develop the autoradio-graphic method' quantitatively for use in diffusion studies. Results are reported here for the self-diffusion of silver. Silver was chosen because the existing data are good enough to evaluate the technique." The silver used in this investigation was obtained in the form of ¼ in. diam rods of polycrystalline material, 99.99 pct purity. The radioactive silver, Ag110 (ß, y), was obtained as the nitrate and converted to the chloride for use in a standard cyanide plating bath. The diffusion specimens were 1/2 in. lengths of the rod. They were mounted in bake-lite and the exposed circular face carefully ground and polished. Prior to electrodepositing radioactive

Jan 1, 1956

REPUBLIC STEEL CORP. and Armco Steel Corp. have joined in a $160,000,000 project for the production of iron ore from Taconite in the Lake Superior mining region. The two companies announced acquisition in equal shares of 100 pct ownership of the stock of Reserve Mining Co., which controls a vast deposit of magnetic Taconite iron ore on the eastern end of the Mesabi range in Minnesota. Through Reserve Mining the two companies will build a plant for manufacturing high grade ore from Taconite near Beaver Bay on the north shore of Lake Superior. The first announcement calls for about a $60,000,000 plant which will be built as soon as plans are completed and will have an annual capacity of about 2,500,000 tons of iron ore pellets. Longer range development plans call for future expansion of the plant to provide an annual capacity of 10,000,000 tons. This will amount to an additional investment of

Jan 10, 1950

By P. B. Barton, P. M. Bethke, R. O. Rye

Rhyolitic welded-tuff wallrocks of the epithermal base and precious metal veins of the Creede district were pervasively altered by the addition of more than two billion metric tons of potassium some 1.5-2 million years before mineralization. Sodium, calcium and magnesium were strongly depleted, yielding a nearly binary quartz + potassium feldspar assemblage containing as much as 13 weight percent K 0. This large-scale metasomatism, originally noted by Steven and Rattle (1965), took place progressively by initial alteration of plagioclase phenocrysts to orthoclase or microcline followed by alteration of the groundmass feldspar to orthoclase and gradual change of the sanidine phenocrysts to more Or-rich compositions. Oxygen isotope and chemical studies show that the metasomatism resulted from the interaction of the tuffs with deeply circulating heated ground water and suggest that the potassium metasomatism of rhyolitic rocks is the facies equivalent of propylitization of volcanic rocks of more basic composition.

Jan 1, 1985

A letter has been received by the Secretary of the Institute from Mr. C. W. Purington, Honorary. Secretary of the. American Committee of Engineers in London, whose offices are at 6, Copthall Avenue, London, E. C. 2, which will be of interest to any member who may be intending to go to England. Mr. Purington says: "A Committee of Americans has been formed here, consisting mostly of Mining Engineers, and those interested-in mining and allied industries. We should be very glad, among other duties, to give assistance to any American engineers arriving in England on official business connected with the war. This assistance would probably take the form of offering advice and hints as to saving time in approaching British official Departments, and generally in getting. about." This Committee of Engineers was organized with the approval of the American Ambassador to Great Britain, who has recommended its services to the United States Government in connection with the conduct of the war.

Jan 7, 1917