Search Documents

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By Ira B. Joralemon

Neighboring mines, like men who live in the same environment, often assume similar characteristics. In the Bridge River area of the Lillooet district in central British Columbia there is a remarkable exception to this rule. The Pioneer mine has a simple fissure over 3000 ft. long, with no faults of more than a few feet and with only minor variations in width; the Bralorne mine, 2½ miles away at the other end of the same intrusion, has developed one of the most intricate vein and fault systems in the West. Hinged faults displace the main vein for hundreds of feet, and sometimes become valuable veins themselves. The width of ore varies in a few yards from 2 to 60 ft. Changes in grade of ore are just as abrupt. The rocks that follow the veins or are cut by them often grade into one another or into the ore with no definite contacts. Although the complexity of the structure has left many problems unsolved, the development has indicated a fascinating geological pattern. The Bralorne is in the eastern portion of the Coast Range, 55 miles by spectacular mountain road from the Pacific Great Eastern Railway station of Bridge River. The adit tunnel runs easterly from Cadwallader Creek, a tributary of Bridge River that flows into the Fraser River. Steep mountains rise from 3300 ft. elevation above sea level at the creek to peaks and ridges at 8000 to 9000 ft. altitude. The lower slopes are heavily wooded while above 5000 ft. bare rocks, glaciers and snow-fields extend far above timber line. See Fig. 1. Story of the Bralorne The Lorne claim, staked in 1897, was one of the earliest lode locations in the Bridge River district. At that time it was 70 miles by steep and treacherous trail from the railway. For the next 15 years Arthur Noel, Will Haylmore and other local prospectors mined the small, irregular, oxidized quartz veins to a maximum depth of 200 ft., and treated the ore in arrastres and later a five-stamp mill. The total production to 1912 was only $55,000. Noel and associates later formed the Lorne Amalgamated Mines Co., which they worked in a desultory way until 1925. Increasing sulfide and arsenide content in the veins

Jan 1, 1935

By John C. Calhoun, Raymond G. Loper

Theoretical calculations for the decline of pressure and the variation of instantaneous producing gas-oil ratio with increased cumulative production have been made for reservoir systems under various producing drawdown values and for various spacings. These variables have been included by a modification of previously Published techniques. This consists essentially of utilizing a radial system flowing gas and oil in a succession of steady state calculations. The results of the calculations do not show any variation in the predicted behavior of the internal gas drive reservoir when either the drawdown or the spacing are changed. The prediction of performance on an internal gas drive reservoir has been presented by various authors. ',"' These predictions are in the form of a pressure decline and an instantaneous producing gas-oil ratio as a function of cumulative oil withdrawal. In making these predictions a basic assumption has been that the saturation of the reservoir is uniform throughout at any time, or that the pressure differential imposed on the reservoir system is zero. Because of these assumptions the validity of such predictions has been questioned. Their application to actual systems, where saturations are not uniform and where producing differentials exist, has been a hazardous procedure. The authors cited have used different methods of approach to the derivation of equations for making their predictions and for arriving at a solution of both equations, but basically the same relationships are utilized in each case. In all instances the instantaneous producing gas-oil ratio is calculated from the equation: In utilizing this equation an average reservoir pressure and an average reservoir saturation must be known, the former to define ß, v, s, and uo/ug and the latter to define kg/ko. Predictions can be made, therefore, only for the conditions of a uniform reservoir saturation and a uniform reservoir pressure. This restriction of requiring a uniform oil saturation can be resolved by applying two-phase steady state flow for the radial system to the reservoir's history. Radial steady state flow is defined when the ratio of phases flowing,

Jan 1, 1949

By John C. Calhoun, Raymond G. Loper

Theoretical calculations for the decline of pressure and the variation of instantaneous producing gas-oil ratio with increased cumulative production have been made for reservoir systems under various producing drawdown values and for various spacings. These variables have been included by a modification of previously Published techniques. This consists essentially of utilizing a radial system flowing gas and oil in a succession of steady state calculations. The results of the calculations do not show any variation in the predicted behavior of the internal gas drive reservoir when either the drawdown or the spacing are changed. The prediction of performance on an internal gas drive reservoir has been presented by various authors. ',"' These predictions are in the form of a pressure decline and an instantaneous producing gas-oil ratio as a function of cumulative oil withdrawal. In making these predictions a basic assumption has been that the saturation of the reservoir is uniform throughout at any time, or that the pressure differential imposed on the reservoir system is zero. Because of these assumptions the validity of such predictions has been questioned. Their application to actual systems, where saturations are not uniform and where producing differentials exist, has been a hazardous procedure. The authors cited have used different methods of approach to the derivation of equations for making their predictions and for arriving at a solution of both equations, but basically the same relationships are utilized in each case. In all instances the instantaneous producing gas-oil ratio is calculated from the equation: In utilizing this equation an average reservoir pressure and an average reservoir saturation must be known, the former to define ß, v, s, and uo/ug and the latter to define kg/ko. Predictions can be made, therefore, only for the conditions of a uniform reservoir saturation and a uniform reservoir pressure. This restriction of requiring a uniform oil saturation can be resolved by applying two-phase steady state flow for the radial system to the reservoir's history. Radial steady state flow is defined when the ratio of phases flowing,

Jan 1, 1949

By Wilbur C. Helt

The United States is self-sufficient in bituminous coal and lignite resources to meet the high range of energy demands forecast for the remainder of this century and beyond. The known or proved recoverable reserves of energy from coal in the United States are estimated to be 88% of all fuel reserves, whereas the energy reserves for oil are estimated to be 276, gas 376, shale oil 5% and uranium 2% (as now used). The demand for all forms of energy used in the United States is increasing at a rate of 3% to 4% per year. Presently, coal is competitive on a supply and cost basis with other fuels in conversion to electrical energy and as a source of energy for converting raw minerals to metals and nonmetals, but it is not competitive in transportation and other uses that demand the high flexibility that oil and gas enjoy because of their form. Coal conversion to fluid forms is essential to make it interchangeable with gas and oil to meet the markets they now occupy. Essentially, the chemical constituents that make up coal are the same hydrocarbons that make up oil and gas; it is a matter of reconstituting the proportions of hydrocarbons to make coal interchangeable with the other fuels. The production of coal has fluctuated widely between the peak production of 631 million tons in 1947 to a low of 403 million tons in 1961. Throughout this period, the total value of the production, f.o.b. mines, has averaged more than $2 billion annually. Beginning with 1962, there has been a steady upward trend in coal production with only minor fluctuations that were mainly caused by labor disputes. Output for the latest typical year, 1970, was 588 million tons. Production in 1971 was affected by a major strike and dropped to 548 million tons. Exports of coal from United States to foreign countries have increased steadily and developed into a substantial annual market for over 71 million tons per year. About 56 million tons of this is suitable for metallurgical purposes, and the remaining 15 million tons is exported for electric power generation. The largest single-industry demand for coal is in the electric generating industry, Fig.1. Roughly, the production of electricity has doubled every

Jan 1, 1973

TO THE BOARD OF DIRECTORS AND THE MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Herewith are submitted the report of the Treasurer for the year 1936 and the reports for the same year of the following committees: Admis¬sions, Membership, Papers and Publications, Library, Student Relations, and MINING AND METALLURGY. To these reports you are referred for details of the year's activities. Finances.-Income for the year was $173,091 including an appropria¬tion of $2500 from the Rocky Mountain Fund earmarked to defray expense for official visits to western Sections and student societies. This compares with $141,754 in 1935 and exceeds by more than $50,000 the income of 1933 wherein the low point during the depression was reached. The major items of increase were: $6,700 from current dues; $10,600 in initiation fees and dues of newly enrolled members; $10,800 from the monthly magazine MINING AND METALLURGY. Sundry small declines were offset by minor increases. Expenditures for the year totaled $176,007 compared with $148,361 in 1935. Major increases were $5,700 for MINING AND METALLURGY; $4,000 for TRANSACTIONS and TECHNICAL PUBLICATIONS; $1,500 for meetings; $1,300 for Local Section appropriations; $6,500 for Technical Division expense; $5,000 for Increase of Membership expense; and $2,500 for visits to Local Sections and educational institutions. Comment on several of these items will appear under subsequent heads. Net deficit for the year was $2,915, this sum being made up from the accumulated surplus. It is interesting to observe that the net excess of income over outgo for the five-year period 1932-1936, inclusive, is $760. Membership and Dues.-During the year there was a net gain in membership, including Members, Associates, Junior Members and Junior Foreign Affiliates of 755 (from 7116 to 7871). In addition there was a gain of 616 in Student Associates (from 1004 to 1620). Taking account of small losses totaling 5 in the other grades, the net increase was 1366 bringing the total to 9607, the highest figure reached in the history of the Institute except at the end of 1921 when the total was 9850. In part the gain is accounted for by the smaller number lost by suspension

Jan 1, 1937

By W. A. Ver Wiebe

It is becoming increasingly apparent that the State of Kansas contains one of the largest reserve areas for oil exploration in the United States. During the year 1936 no less than 54 new oil pools were discovered by drilling. In addition, seven gas pools were found, which may develop into oil pools when deeper horizons are tested. Several old pools increased their reserves when production was found in lower strata. The data presented in Table 2 indicate that nearly 2000 wells were drilled in the state during 1936. Of these more than 1214 found commercial quantities of oil and at least 61 found marketable quantities of gas. The data are conservative because complete results on drilling are not available for the eastern part of the state. Ellis, Rice and Russell Counties share honors with a total of 10 new pools in each. Barton County is prominent with six pools; while those counties claiming fewer new pools are Clark, Ellsworth, Harvey, McPherson, Ness, Pawnee, Rooks, Stafford and Trego. Important additions to our gas reserves were found in Finney and Haskell Counties, which are north of the extensive Hugoton gas area and may some day be part of it. At the close of the year there were 17,317 wells in the state rating as producers. By far the larger share (14,000) were classed as strippers and allowed to flow 100 per cent of their potential capacity, thus accounting for 33,500 bbl. a day. The remaining wells, capable of producing from 15 up to over 6000 bbl. per day, were limited in output according to these amounts. The largest wells having a potential of from 3000 to 7000 were allowed to flow from 2 to 3½ per cent of their official potential capacity. The percentage rises until wells of 15 to 20-bbl. capacity have a rating of slightly over 83. On the basis of these calculations the total potential capacity of all wells was 1,667,814 bbl., and the daily amount allowed was 175,851. Nine of the pools most recently opened were still unable to market their oil and were classified as "shut-in" pools. Total production for the state for 1936 was somewhat over 58 million barrels. Striking Geological Data Some interesting geological data were uncovered by deep drilling during the year. The most remarkable bit of information is the discovery

Jan 1, 1937

By M. J. Hordon

Measurements of the 103 yield stress of ordered and disordered poly crystalline Cu ,Au were related to the ordered antiphase domain size determined by resistivity measurements. For undeformed material, a yield stress maximum wa obtained at a critical domain diameter of about 40A. Plastic deformation resulted in a marked increase in the yield stress and electrical resistivity of the ordered alloy compared to the disordered, the strain hardening rate increasing regularly with initial antiphase domain size. Order hardening was accompanied by a sharp reduction in size of the initially large domains. It has been observed that the yield stress of ordered and partially ordered Cu3Au alloy varies sensitively with antiphase domain size aid degree of order.ly2 In addition, ordering of the lattice leads to a marked increase in the strain hardening rate (order hardening) as compared to the rate for the disordered alloy. In the present investigation, changes in the electrical resistivity and yield stress of ordered polycrystalline Cudu with varying initial domain diameters were measured after tensile plastic deformation in order to examine the effect of cold work on the antiphase domain size. EXPERIMENTAL PROCEDURE Au-Cu alloy of 99.99 pct purity analyzing 50.85 wt pct Au-balance copper was obtained from the Handy-Harmon Co., N. Y., in the form of 0.061 in. diam drawn wire. Wire specimens 3 in. in length were given the following annealing treatment in nitrogen: 500" for 72 hr, 820" for 15 hr, and 450" for 5 hr, followed by a water quench. The annealing sequence resulted in a completely disordered structure with a grain size of about 0.2 mm. The disordered specimens were then reannealed at 360' in nitrogen for periods varying from 10 min to 150 hr followed by quenching to produce ordered structures with varying domain sizes. The degree of ordering and variation of domain size was followed by electrical resistivity measurements made at room temperature using a low resistance precision Kelvin double bridge apparatus. The specimen resistance was determined over a length of 4.0 cm between two brass knife-edge contacts while the specimen was immersed in an oil bath to minimize temperature variations. In addition, the current flow in the circuit was minimized by a current pulse technique in balancing the bridge in order to avoid heating the specimen. Using a sensitive galvanometer to detect the bridge null, the accuracy of the resistance measurement Wire specimens were plastically strained in tension with an Instron tensile unit at strain rates in the range 5 x 10"5 sec-' to 2 x 10"4 sec-'. Stress and extension data were fed into the Instron chart drive amplifier to obtain the actual stress-elongation curve from which the yield stress at 10"3 strain was determined. The maximum resolution of the apparatus was approximately 50 psi stress and 3 x 104 strain. At various plastic strain levels, deformation was interrupted and the electrical resistivity determined after removing the stress. RESULTS AND DISCUSSION 1) Yield Strength of Ordered Cudu. In order to determine the effect of the ordered antiphase domains on the initial yield stress, specimens were prepared with varying domain sizes ranging from zero for 5 completely disordered structure to about lo5A for a completely ordered structure by suitable annealing treatment. Domain sizes were estimated by comparing room temperature electrical resistivity data with the original data of Jones and sykes3 as modified by rdle.' In agreement with previous work, the resistivity varied sensitively with domain diameter and degree of order, decreasing from approximately 11.6 x l0- ohm-cm for the disordered structure to about 5.9 x l0- ohm-cm for ordered domains above 10"3 cm in diameter. Fig. 1 shows the change of the 103 yield stress with ordered domain size. It is evident that the maximum

Jan 1, 1963

By G. Rowan, M. W. Clegg

Approximate analytical solutions for non-Darcy radial gas flow are derived for bounded and infinite reservoirs producing at either constant rate or constant pressure. These analytical solutions are compared with published results for non-Darcy flow obtained on digital and analogue computers, and the agreement is show to be very good. Some observations on the interpretation of gas well tests are made. INTRODUCTION The flow of gases in porous media is a problem that has been the subject of much study in recent years [l - 71 , and many methods have been proposed for solving the non-linear equations associated with it. The assumption that the flow satisfies Darcy's Law It has been observed, however, that the linear relationship between the flow rate and pressure gradient is only approximately valid even at low flow rates, and that as the flow rate increases the deviations from linearity also increase. It has been suggested by a number of authors that Darcy's Law should be replaced by a quadratic flow law of the form This form of equation was first suggested by Forchheimer [9] and, later, Katz and Cornell [10], and Irmay [lll, developed a similar equation. Houpeurt [12] derived this form of equation using the concept of an idealised pore system in which each channel consists of sequences of truncated cones giving rise to successive restrictive orifices along the channel. This type of representation leads to a quadratic flow law of type [4], for all fluids, but it is found that the quadratic term is only significant in the case of gas flow. The methods of Houpeurt for solving gas flow problems will be discussed further in another section of this paper. Solutions of the non-linear equation for Darcy gas flow 121 may be classified as either computer (digital and analogue), or approximate analytical ones. The former include the well-known solutions of Bruce et al. [13], and Aronofsky and Jenkins [14] , but the latter solutions, apart from the simple linearisation of equation (2) to yield a diffusion equation in p2 , are not so well-known. Amongst these approximate analytical solutions should be mentioned the work of Barenblatt [IS], who has applied the techniques of dimensional analysis to obtain similarity solution to a large class of non-linear equations; also, a number of Russian authors, including Barenblatt [16] , Kim [17] and others, who have used the method of moments for obtain-

Jan 1, 1965

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By A. R. Denison

Several productive areas in the Mid-Con-tinent are broadly and briefly examined with respect to the present depth of drilling on productive structures, and the thickness of sediments remaining untested. Evidence is offered to show that a vertical mile to two miles of untested but prospective formation remain within reach of the drill. In no case would a well deeper than 15,000 ft. be required, and in most cases to no greater depth than 10,000 ft. Recent outstanding success of deeper prospecting in West Texas demonstrates the merits of deeper drilling on known structure. Introduction New fields discoverd during I942 equaled or exceeded the number in any preceding year. The total amount of oil found by these discoveries was less than in any previous year, for which accurate records are available. This means that the pools now being discovered are much smaller than in past years. This is to be expected, since the prospects available during 1942 were largely those overlooked in the earlier years and therefore represent a second or third order (in quality) of structural feature. This failure to find pools of good size and quality raises grave doubt as to the security of our future oil supply. With military needs rising almost daily, and the period of heaviest con- sumption in our war effort still in the future, there is even a growing doubt as to our ability to supply the amount needed for our ultimate victory. This does not mean that our reserves are inadequate, but rather that our "capacity to produce" may be inadequate. Lacking large fields with flush production, our capacity to produce is rapidly approaching our current needs. ,Since the industry is unable to find the large new fields necessary to keep a safe margin of "capacity to produce," other means are needed. It seems obvious that one of these should be deeper prospecting on the large, proven, productive structural features now known. The exploratory wildcat is drilled primarily in search of a trap and the reason for failure to find oil and gas in nine out of ten cases is due to the absence of a suitable trap under the drill site. Therefore, deeper drilling on a known structural feature that is productive largely eliminates the greatest hazard in wildcat drilling. While by no means all the oil known today is found in structural traps—in fact, some have estimated that less than half is so located— the fact remains that structural traps are far more commonly the oil fields that have multiple horizons of production superimposed one over the other. Outstanding examples are the Eldorado field in Kansas, the Tonkawa and Cushing fields in Oklahoma, the Louden and Salem pools of Illinois, and the richest and most prolific of all structural traps, the Long Beach, Ven-tura and other similar fields of California.

Jan 1, 1944

By R. E. Reed-Hill, W. H. Hartt, W. A. Slippy

An unusual form of double kinking has been observed at the ends of {1121} twins in deformed zirconium. These kinks lie partly outside of the twin and partly inside. While they are undoubtedly closely associated with accommodating the twinning shear into the matrix, they are apparently closely related to other important aspects of twin growth. A mechanism is proposed for {1121} twin growth involving interactions between 1/3 (1120) dislocations in the bend planes and twinning dislocations. It is also shown that boundaries without long range strain fields develop at the tapered ends of the twins. The {1121} twins can, therefore, grow without forming high-energy noncoherent twin boundaries containing large numbers of closely spaced twinning dislocations. NUMEROUS investigators have indicated that slip is often closely associated with deformation twinning. An example is twin accommodation kinking,1-3 where dislocations form bend planes and permit accommodation of a twinning shear within the parent crystal. Another is the incorporation of slip dislocations into twins, as proposed by Sleeswyk and verbraak4 and Ishii and Kiho5 for iron and ß-tin, respectively, and observed in hcp metals by Price.6 In addition, it has been shown that shear discontinuities exist at the points of twin intersections in zinc,7 magnesium,8 titanium,9 ß-tin,10 and bismuth," where the continuity conditions for twin intersections, originally proposed by cahn,12 are not satisfied. A similar situation occurs for zig-zag (1121) twins in zirconium13 and ?-phase silver-aluminum alloys,14 where the twinning shears of the two component twins are not parallel. In all these latter cases additional deformation by slip is believed to accommodate the twinning shear discontinuity. The present paper is concerned with a newly observed aspect of the slip and twinning interrelation, in which two kinks, one inside the twin and the other external to the twin, are formed. These kinks, observed in conjunction with (1121) twinning in zirconium, form to accommodate the twinning shear. A model has been constructed explaining the growth and accommodation of (1121) twins in terms of these kinks. This mechanism may be significant since it is concerned with an important twin mode, which occurs not only in zirconium but also in titanium and hafnium. The practical significance of (1121) twinning has been adequately demonstrated. At 77° K the high ductility of zirconium containing a large number of grains unfavorably oriented for slip is primarily due to (1121) twinning.'5 Also, (1121) twins nucleated at 77°K may grow during further deformation at room temperature. This growth can greatly increase the transverse ductility15 as well as produce large mechanical hysteresis effects.= EXPERIMENTAL PROCEDURE Arc-melted, sponge zirconium plate previously described17 was prestrained 0.65 pct at 77° K by cold-rolling to introduce {1121} twins into the structure. Tensile specimens were cut with axes normal to the plate rolling direction. These specimens were pulled in tension to near the point of failure in an Instron machine at room temperature at a cross-head speed of 2 x10-2 in. per min. This additional deformation caused growth of the twins nucleated by prestrain. Deformed specimens were then prepared for metallo-graphic examination. This included an anodizing treatment18 that made the surfaces sensitive to polarized light, permitting small lattice rotations to be revealed. EXPERIMENTAL RESULTS Nature of the Twin-Kink Band Structure. Fig. 1 is a photomicrograph of a typical specimen after prestrain at 77° K. The structure is characterized primarily by long, narrow, parallel sided (1121) twins which norma1ly traverse the entire grain. Fig. 2 shows several (1121) twins after additional straining at room temperature. These lie near the center of the polarized light photomicrograph and are inclined upward to the right. It is evident that this latter deformation has resulted in appreciable twin growth. The dark regions extending from the ends of these twins are accommodation kinks. The difference in reflected light intensity indicates the

Jan 1, 1969

By R. C. Patterson

In view of the circumstance that very few important changes have been made within the last 15 or 20 years in the equipment of rod and wire mills, the description of a new process introduced by Grenville Mellen, of LleweIIyn Park, N. J., to take the place of the present laborious system of producing rods of lead, zinc, brass, copper, aluminum, etc., may be interesting to members of the Institute. This new process consists in the production of cast rods at one operation in a small continuous casting machine. The hot liquid metal is transferred from the melting crucibles directly into an endless chain of mold blocks in the machine, where solidification takes place, and the rod comes out continuously in a solid form at one end as long as the molten metal is supplied. The operation of these mold blocks so as to produce a solid rod of uniform structure constitutes an important part of Mr. Mellen's invention. The machine (Figs. 1 and 2), 12 ft. in height over all, 2 by 3 ft. in horizontal cross-sectional area, and 6,000 Ib. in weight, has a framework of cast iron, holding in position two endless chains of mold blocks, which are made in sections and join in center alignment. The mold orifice is made up of these mold sections, into which the liquid metal flows. The molding chains are composed of steel blocks, grooved on one face to form the molding cavity, and linked together with flexible joints. Each block is carried on four rollers which guide the chain around the end sprockets and carry it in its course through the machine. The accuracy of alignment requisite to the production of a perfect rod in the mold groove formed by these sections is secured by careful machine work, and by building the four ways, down which the alignment takes place, so that two of the sides are fixed permanently, whiIe the opposite sides are held to their position by spring pressure. The guides carrying the molds, while in casting position, are water-cooled square tubes. The length of this machine is somewhat indeterminate. A certain amount of both time and cooling surface is required to solidify the metal jn the mold; and one may either use a long molding chain and run it fast, or a shorter chain and run it correspondingly slower. We have found,

Jan 1, 1916

By C. A. Heiland

The new geophone described herein was developed by Charles H. Hull, instrumentmaker of the Colorado School of Mines, and the writer. The first geophone was invented during the war for the purpose of detecting enemy sapping or underground mining operations and for locating enemy artillery. It is based on the principle of the seismograph—a heavy lead mass suspended by one or two diaphragms, which are clamped to an air-tight case. When the ground vibrates during the transmission of sound waves, the case moves with it while the so-called steady mass remains practically motionless. Attached to the top of the casing is a hose leading to an earpiece shaped like a stethoscope. When the mass and the diaphragm move up and down in the case, the air is compressed and rarified in the inside; thus the vibration is communicated as sound wave to the human ear. The geophone combines a surprising simplicity of construction with an extreme sensitivity. Other listening instruments were developed during the war, adaptations of the telephone and the microphone—that is, instruments operating through the medium of electricity—of which the so-called seismicrophone, an adaptation of the carbon-granule microphone receiver, probably has found the greatest application, but such instruments apparently have not proved as useful as the simple geophone despite obvious advantages arising from the use of electricity. The carbon receivers were more subject to extraneous noises and to what is called "frying," and they did not offer the advantage possessed by the geophone; namely, the simultaneous use of two receivers, which makes it possible to determine the location of the source of sound. During the war, the U. S. Bureau of Mines made a study of the geophone and of the propagation of sound waves through rock. These studies have been continued, as the earlier results proved the possibility of using the geophone in various non-military ways, principally in mining, and the results of these studies have been published.'

Jan 1, 1932

By Richard W. Markley

A centralized online data acquisition system has been developed by the U.S. Bureau of Mines Pittsburgh Mining and Safety Research Center for rapidly digitizing, storing, and processing experimental signals originating up to 1100 feet away from a central computer. This system, which services seven laboratories, is currently based on a CDC System 17 1/- computer with 56K of semiconductor memory, four disk drives (one shared online with a CDC 1700), two magnetic tape drives, high-speed A/D hardware, and other input/output peripherals. The laboratories are linked to the central computer by 15-pair cables and signal conditioners and to the computer's communications controller by modems and current loops. The A/D throughput rate is approximately 30,000 samples per second (9 bit plus sign resolution) and permits scanning about 30 instruments once every millisecond for up to 100 seconds, being limited only by disk capacity. The laboratories serviced by this facility conduct explosions research and include such facilities as an Experimental Coal Mine Explosion Facility (45 channels), a Constant Volume Combustion Laboratory (4 channels), and a Simulated Coal Mine Laboratory (15 channels). Personnel support includes one systems analyst, two applications analysts, one operator, and a hardware technician. The system has performed adequately for burst-type data acquisition, but due to a lack of long-term reliability (24 hours) of the real-time multiprogramming operating system and unpredictable power failures, slow phenomena signals are generally digitized and stored offline. This latter data is input to the computer through peripherals such as a high-speed paper tape reader, or high-speed asynchronous communications ports. Processing of data is done either in real-time (as soon as data is collected) or in batch mode. Smaller batch jobs are run on this computer, and all others are transmitted by means of the system's high-speed UT 200 terminal simulator to a CDC-6000 series computer.

Jan 1, 1977

By J. B. Wagner, B. Swaroop

The atomic ratios of oxygen to iron in zlarious corn-posilions of wustite in the vicinity oj the reported p to n transformation were determined in the temperalure range between 950" and 1250°C. For these conditions, equilibrium vacancy concenrations have also been determined at vatious mixtures of C0,-CO. The data show a continuos introduction of iron vacancies as oxygen is introduced into wuistite. No phase change is observed with in the wuustite field. However, the value of n in the isothermal oxygen pressure dependence, the weight change shifts to 1ower values as the concentration of oxygen increases. WUSTITE is a metal deficit semiconductor with the majority lattice disorder being cation vacancies. Using the notation similar to that of Kroger and ink,' the dissolution of oxygen into wiistite using C02-CO mixtures is represented by, WHere v+! denotes a cation vacancy with k effective negative charges and kh • denotes k electron holes, h -. Applying the law of mass action and assuming a dilute solution of defects in the wiistite yields Where the square brackets denote concentrations. Furthermore, when k = 2 the cation vacancies are completely ionized, and both the concentration of cation vacancies and the concentration of electron holes are proportional to the third root of the ratio, PC /PCo. This analysis is valid for one particular mael based on an ideal solution at elevated temperatures (in this case t > 1000°C). At lower temperatures, it has been shown2 that the pressure dependence of the electronic conductivity changes in a manner which suggests that vacancies interact with or "trap" electron holes. At the very high concentrations of defects, 10'' to 10" per cu cm, these simple models no longer hold. Recently Tannhauser,3 Geiger et a1.' Bransky and Tannhauser; and Hillegas' have found an apparent p to n transformation in wiistite in the temperature range of 950" to 1300°C. This junction was found by thermoelectric and electronic conductivity measurements. Geiger eta1.' found that the electronic conductivity became almost independent of the oxygen pressure at high temperatures and oxygen concentrations within the experimental error. In addition, Vallet, Raccah, and coworkers6'7 have reported the existence of several "varieties" of wiistite which were reported to exist within what was heretofor presumed to be a

Jan 1, 1968

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black stone, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 years before the Christian Era. And, from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, goes back for thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of a slight use by the Indians. However, the first recorded discovery of coal, in what is now the U.S., was by French explorers, who reported a "cole mine" on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coalfield near Richmond, Va., a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New Pork, and Boston. During the Revolution this coal was of importance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1973

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938