Search Documents

By John B. Pearse

The works heretofore used in carrying out the Bessemer process have been constructed substantially as follows: The whole works or plant has been divided into three parts. 1. The division in which the metals for conversion are melted. 2. The division in which the metals are converted into steel and cast into ingots, or the converting department. 3. The engine and boiler department which supplies the hydraulic power required to move the machinery, and which furnishes the blast used for converting the crude metal into steel.

By Robert Mehl

THE system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that FIG. 1.-BIJL'S DIAGRAM FOR CADMIUM-MERCURY ALLOYS. developed by Bijl1 (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1929

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month, Twenty-third Meeting The Twenty-third Meeting of the Boston Local Section was held at the Engineers' Club, 2 Commonwealth Ave., on Monday evening, Nov. 30,- 1914. Prof. R. A. Daly addressed the meeting on The Iron Ores of Küruna; Sweden. AUGUSTUS H. EUSTIS Secretary.

Jan 1, 1915

By George R. Cowan

A number of studies hare been reported of the effects produced in metals subjected to deformation by shock waves with maximum pressures ranging from tens to hundreds of kilobars. On the basis of the equations for the flow of mass, momentum, and energy through a stationary shock front, the macroscopic stress-strain curve for the resulting shock deformation can be calculated within narrow limits from the experimentally determined Hugoniol curve. In relatively weak shocks which are preceded by an elastic wave, the stress rises above the clastic limit only as plastic deformation proceeds cold thus the shock has a long toe. In strong shocks that override the elastic wave a high stress is applied without prior plastic deformation. A more important effect of increasing the shock pressure is the generation of shear stresses, called supercrilical shear stresses, that exceed the strength of the perfect lattice. A change in the mechanism of deformation is expected to result from the onset of supercritical shear. The shock disordering of ordered Cu3Au in strong shocks appears to be an example of such a change. It is suggested that the formation of fine twins in copper and nickel and the formation of structures which enable visible twins to be formed in the rarefaction ware, observed in copper and presumably in disordered Cu3 Au, are related to the occurrence of supercritical shear in shock dcformation. In recent years several studies1,2 have been made of the changes in structural and mechanical properties of metals produced by the passage through the metals of strong shock-compression waves ranging from about 50 to 800 kbar pressure. Recent work involving dynamic measurements of the shock compression "Hugoniot" curves 3-8 of many metals has developed techniques and provided data required to obtain the shock pressure and the (transient! plastic deformation produced in the shock-conlpression experirnents.9 Shock deformation has been found to be much more effective than slow deformation in changing the mechanical properties of metals, when the two are compared on the basis of equal plasti strain, Holtzman and Cowan9 made quantitative estimates of the shearing stress occurring in a shock front in a metal by assuming that the shearing stress is similar to that occurring in a shock front in a viscous, heat-conducting fluid, with the addition of a yield stress. Taylor's solution9 for a weak shock was used to estimate pairs of values of shearing stress and thickness of the shock front obtained by assumed choices of the ratio of effective kinetic viscosity to thermal diffusivity. It was noted from these values that. unless the shock front is extremely thin. heat conduction has slight effect, and the shearing stress is nearly independent of the mechanism of deformation. This mechanism does, however, determine the thickness of the shock front and the rate of strain. Furthermore, since the maximum possible shearing stress occurring in shocks of moderate strength does not greatly exceed the shear stress occurring in conventional slow deformation, the mechanism of deformation is not expected to be qualitatively different. The greater effectiveness of shock deformation in changing the mechanical properties of metals can be attributed partly to the fact that dislocations, when driven by near-conventional stresses, cannot keep up with the shock front, thus necessitating a higher dislocation density than required for an equivalent slow strain. The fast uni-axial strain occurring in the thin shock front would also be expected to cause a larger number of dislocation intersections to occur. In the upper range of shock pressures that have been studied the estimated values of the shearing stress exceeded the estimated shear strength of a perfect crystal. Under these circumstances it is reasonable to expect that the mechanism of deformation might be considerably different from that involved in slow deformation. Except for the observation by smith1 of twins in shocked copper, the effects of shock waves on metals did not show any obvious or large changes in properties that would indicate the onset of a change in the mechanism of deformation. The recent investigation of the effect of shock waves on ordered and disordered specimens of Cu3Au by Beardmore, Holtzman, and ever" showed a spectacular decrease in the amount of long-range order retained by initially ordered Cu3Au when the shock pressure was raised from 290 to 370 kbar. Since Dr. Holtzman and I suspected that this behavior probably was due to the onset of a shearing stress in the shock front in Cu3Au which exceeded the limiting shear strength of the perfect crystal. it was considered appropriate to examine directly the shock-front equations for a solid. and to obtain a sound estimate of the shearing stress occurring in the front using equation of state data obtained from shock studies. In this paper an estimate is made of the

Jan 1, 1965

By N. Arbiter, C. C. Harris

Analysis of ball and pulp flow in ball mills indicates that three factors may become critical with increasing mill diameters: ball size, fraction critical speed, and average pulp flow velocities. Ball diameters may need to be decreased and fraction critical speeds increased with ores which show decreased breakage rate coefficients above 1.2 mm (14 mesh). With 5.5-m (18 ft) and larger mills at higher circulating loads, pulp flow velocities may become capacity limiting and also may limit increases in ball mill diameters.

Jan 1, 1985

By J. Weijdema, D. N. Dietz

In the conventional underground combustion process (dry combustion) much heat is left behind in the swept formation and goes to rva.rte. Econonmy can be improved by heat recuperation through water injection. This is most advantageous if done at the earliest opportunity before much heat is dissiputed to cap and base rock. Water injected simultaneously with the air will flash to superheated steam, which passes through the combustion front together with the nitrogen from the air. A condensation front traveling up to three times as fast as the combustion front drives out the oil. In this type of wet combustion, the water evaporates before it reaches the combustion zone. The evaporation front travels more slowly than the combustion zone. If so much water is injected that the evaporation front overrun the combustion front, combustion in that spot will be quenched and some unburned fuel will be left behind. Air reacts with the oil farther down-stream where steam temperatures occur; at steam temperature, the air reacts rapidly with the oil. Velocity of the combustion front is increased thereby and is governed essentially by the water-injection rate. In the extreme case of high water-injection rate, a short heat wave of constant length is driven through the formation by water injection. Once this wave has been established, no more heat need be generated than that required to make up the heat losses from the short heat wave; a relatively low rate of air injection will suffice. The feasibility of partially quenched combustion has been confirmed in tube experiments. A heat wave at steam temperature is observed. Chemical analyses of flue gas indicate preferential burning of hydrogen while a carbonaceous residue is left in the formation. Introduction A disadvantage of so-called dry in situ combustion is that air-compression costs are rather high. An air consumption of about 400 std cu m/cu m (400 scf/cu ft) of formation swept is an accepted figure. This high consumption is mostly wasted since much heat is left behind in the depleted oil sand. Methods were investigated for recuperating as much as possible of the heat left behind. This paper deals only with basic principles and is confined mainly to one-dimen- sional flow without lateral heat losses; experiments were conducted in relatively narrow, well insulated tubes. If some water is injected with the air, it will turn to superheated steam in an evaporation front, which should travel behind the combustion front. The steam having passed the combustion front causes a steam drive by a condensation front that can travel faster than the combustion front. The latter needs to travel only part of the distance covered by the oil-displacing condensation front, and thus consumes less air. The water-air ratio would seem limited to that at which cold water overruns the combustion. This limitation was deliberately exceeded considerably in theory and experiments. It was found that combustion is then indeed quenched, but only locally. Farther downstream, the oxygen finds residual oil at steam temperature, which is suficiently high to ensure rapid oxidation. Thus, the combustion front uses only part of the available fuel because it is chased through the formation faster than its normal velocity. No heat is left behind. This new process is called "partially quenched combustion". At the upper limit of the water-air ratio, a small heat slug is moved through the formation by the flow of water and steam. Only a small flow of air is needed since it has only to generate sufficient heat to make up for the lateral heat losses of the short heat slug. Theory Although many factors complicate underground combustion, the processes will be presented in their simplest form. For this reason, one-dimensional flow without lateral heat losses is assumed. Heat conduction in the direction of flow also is disregarded. Under these conditions, dry combustion causes very high temperatures. The heat-carrying capacity of the gas stream is small. Heat generated by oxidation of a residual oil saturation is retained in the sand. The available fuel determines the air requirement and the temperature obtained. Accepting the often-mentioned air consumption of 400 std cu m/cu m (400 scf/cu ft) formation, we calculate a temperature of the swept sand of 1,200C (2,192F) (Fig, I). If water is injected at a modest rate with the air, it will flash to superheated steam upon contact with the heated sand. One cu m (35.31 cu ft) of hot formation will evaporate about 0.5 cu m (17.66 cu ft) of water, and thereafter will accommodate (at an estimated 0.80 saturation and an assumed 0.40 porosity) another 0.3 cu m (10.59 cu ft) of water in cold condition. As long as less than 0.5 + 0.3 = 0.8 cu m (28.25 cu ft) of water is injected for every 400 std cu m (14,125 scf) of air (water-

Jan 1, 1969

By Theron Wasson

During 1936 the state of Michigan produced 11,868,573 bbl. This is approximately 4,000,000 bbl. less than produced in 1935. The principle reason for the decrease in production over the previous year was the rapid decline of the Crystal field, which reached its peak in October 1935. The old producing area—Mt. Pleasant, Porter, Yost-Clark— accounted for over 7,000,000 bbl. during 1936. Crystal produced a total of 2,400,000. Outstanding among the old fields were Vernon and

Jan 1, 1937

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969

By J. D. Miller, M. B. Mooiman

It has been discovered that gold can be extracted from alkaline cyanide solution with primary, secondary, and tertiary amines by adding certain Lewis base modifiers, such as organic phosphorus oxides. Under these circumstances, gold can be extracted at about pH 10, commensurate with the pH of cyanide leach liquors. The selectivity of the amines and amine/modifier combinations for Au(CN)[2] over other metal-cyanide complexes is discussed. Potential applications for the solvent extraction of gold from cyanide solutions are also discussed.

Jan 1, 1985

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-' had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.' Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By G. Cartaud, F. Osmond

WE have already devoted two previous memoirs to this question. In the first we collated and discussed the existing literature on the subject; in the second, we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allotropic states of iron-a, stable below A2; 19, stable between A2 and A3; and 7, stable above A3-all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, but did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier was even led to think from some of our results that iron could very well be a rhombohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Nov 1, 1906

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By V. N. Krivobor

The study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency toward brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had litttle use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: 6L... manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 percent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper. Previous Investigations As early as 1886 the Terre Noire CO.3 in France produced alloys containing up to 2.5 per cent. of manganese, using ordinary low-grade

Jan 1, 1927

By G. Cartaud, F. Osmond

We have already devoted two previous memoirs to this question. In the firstL we collated and discussed the existing literature on the subject; in the second: we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allo-tropic states of iron—a, stable below A2; , stable between A2 and A3; and , stable above A3—all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, and did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier mas even led to think from some of our results that r-iron could very well be a rhom-bohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Jan 1, 1907