Search Documents

By Guy Bjorge

IN recent years the Homestake mine has been served by three shafts, the B. &. M., the B. & M. No; 2 and the Ellison, supplemented by an inside shaft, the Milliken, extending from the 2000-ft. level to the 3200-ft. level. In 1932, when a new operating shaft was under consideration, the bottom of the mine was at the 3200-ft. level. The B: & M. and the B. & M. No. 2 shafts were down to the 1550-ft. level and the Ellison was being deepened from the 2600 to the 3200-ft. level. All ore was hoisted at the B. & M. and-Ellison shafts. Levels below the 2600 level, which were under development only, were served by the Milliken shaft. Below the 1550-ft. level, the mine was served only by the Ellison shaft from the surface. Within a few years, when ore reserves above the 1550-ft. level would be depleted, operation would be limited to the Ellison shaft and the auxiliary underground shaft. The Ellison shaft alone was not adequate for hoisting the entire output from the deeper levels and also handling all men and supplies. Further-more, assurance of safety and uninterrupted operation required- two fully equipped shafts to the deeper levels. Therefore a new operating shaft was authorized in November, 1932, and was named for A. J. M. Ross, the mine superintendent.

Jan 1, 1935

By Clair Upthegrove, Elbert S. Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are: obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from. 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By Charles R. Fettke

BefoRe the Drake well on Watson Flats below Titusville, Pa, inaugurated the modern petroleum industry on Aug. 28, 1859, a considerable industry, based on the manufacture of mineral oils through the destructive distillation at relatively low temperatures (750' to 800' F.) of cannel coals and shales in closed, air-tight retorts, had already sprung up in Europe and America because of the increasing cost of animal and vegetable oils and fats and the growing demand for illuminating and lubricating oils. In 1860, eight out of 55 such coal-oil companies in the United States had plants located in Pennsylvania.' Of these, the Lucesco Works, costing $120,000, situated near Kiskiminetas Junction, was the largest operating in the country. It was equipped with 10 revolving 2.5-ton retorts and 16 stills for rectifying the oil, each holding 2000 gal. The total output of crude oil was almost 6000 gal. per day.2 The discovery of an abundant supply of natural petroleum by the Drake and other wells stopped the distillation of coal oil in America. Most of the smaller plants were closed and others were converted into petroleum refineries. At present, in spite of the temporary over-production of petroleum, the coal and oil-shale carbonization industries are again attracting the attention of far-sighted oil companies who realize that the gradual exhaustion of the American petrol-

Jan 1, 1923

By Charles R. Fettke

BefoRe the Drake well on Watson Flats below Titusville, Pa, inaugurated the modern petroleum industry on Aug. 28, 1859, a considerable industry, based on the manufacture of mineral oils through the destructive distillation at relatively low temperatures (750' to 800' F.) of cannel coals and shales in closed, air-tight retorts, had already sprung up in Europe and America because of the increasing cost of animal and vegetable oils and fats and the growing demand for illuminating and lubricating oils. In 1860, eight out of 55 such coal-oil companies in the United States had plants located in Pennsylvania.' Of these, the Lucesco Works, costing $120,000, situated near Kiskiminetas Junction, was the largest operating in the country. It was equipped with 10 revolving 2.5-ton retorts and 16 stills for rectifying the oil, each holding 2000 gal. The total output of crude oil was almost 6000 gal. per day.2 The discovery of an abundant supply of natural petroleum by the Drake and other wells stopped the distillation of coal oil in America. Most of the smaller plants were closed and others were converted into petroleum refineries. At present, in spite of the temporary over-production of petroleum, the coal and oil-shale carbonization industries are again attracting the attention of far-sighted oil companies who realize that the gradual exhaustion of the American petrol-

Jan 1, 1923

By E. Furubayashi, T. Taoka, S. Takeuchi

Recrystallization textures developed from artificial nucleation around indentations were compared with spontaneously recrystallized textures in two rolled 3 pet Si-Fe single crystals with (111)[112] and (100) [011] orientations. Orientation of individual grains in some stages of their growth was also directly determined by a microetch-pit method. In both the crystals, the recrystallization texture was characteristic of each orientation regardless of any nucleation conditions, artificial or spontaneous, though artificially nucleated grains were more randomly oriented in finer stage. These results support the concept that the process of selection of growing grains controls the formation of the prejerred recrystallization texture. Discussion is given on the factors controlling the mobility of grain boundaries. Recrystallization textures are formed through a number of stages which are customarily called by the terms recovery, nucleation, and grain growth. Many experiments have been done to clarify the mech- anism of formation of recrystallization texture but no fully successful explanation has been proposed. The texture consists of oriented grains which nucleate at many sites of the deformed matrix and grow at the expense of the matrix during annealing. The current theories on the formation of recrystallization texture are based on the following two extreme hypotheses: 1) the oriented nucleation theory by Burgers et al.;1, 2 2) the oriented growth theory by Beck et al.3-5

Jan 1, 1968

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,' but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

By W. J. Heck

The need for a better understanding of the effect of fluid pressure on the strength of intact and jointed rock has long been recognized. The behavior of pore fluid pressure was first pointed out by Terzaghi 1 who suggested the application of the effective stress concept to rock and concrete. While the effective stress concept has been used for some time in the design of mass concrete dams, it only recently has been applied to rock. Robinson 2 and Handin et al.3 evaluated the effects of pore pressure on a variety of sedimentary rocks and demonstrated the validity of the concept. Work using pore fluids other than water has been done by Boozer, et al.4 who considered strain rate and temperature as additional variables. According to the effective stress theory, the effective stress, [a], is the difference between the total stress, [a], and the pore pressure, u, and is the controlling factor influencing frictional strength of rock, other parameters remaining constant. Assuming the Mohr-Coulomb failure criteria applies, the shear strength, T, is given by the equation [r=d+ (a-u)tan ¢](1) where [~F], the angle of internal friction, and c, the cohesion intercept of "no load" shear strength, are the effective stress parameters.* Robinson,2 Handin,3 and others have demonstrated that moderately porous sand-

Jan 1, 1972

By Stanley J. Gasior, Albert J. Forney, Joseph H. Field

Most bituminous coal mined near Eastern industrial areas requiring high-Btu pipeline gas is caking and therefore unsuitable for fixed-bed pres- sure gasification by present techniques. If the caking property of such coal can be destroyed, the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work, strongly caking coals of 1/8- to 1½ -in. size were converted to a noncaking coal char by treatment in a static bed in about 3 hours1 and coal of 18-100 Tyler mesh in a fluidized bed in about 5 min.2 An inert gas such as steam, nitrogen, carbon dioxide or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a noncaking form in free-fall in about 2 sec by dropping it through a countercurrent flow of steam containing 4% to 7% oxygen at 1150º-1200°F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 3, 1965

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By H. Ries

INTRODUCTION OF the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which results in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.1 There appears to he a difference of opinion, however, regarding the temperature at which it is formed. Thus. Klein2 notes that sillimanite forms only above. 1300° C., while Mellor claims that it can develop below 1200° C., the difference in results being conditioned by the time factor. In Klein&apos;s experiments the test pieces were fired in 12 hr., while in Mellor&apos;s, the temperature rose from 800° to 1180° in 24 hrs., and occupied the same time in cooling back to 800°.

Jan 9, 1917

By H. Scott

Since Bohler discovered, in 1903, on cooling certain alloy steels, the phenomenon of a new and lower temperature transformation than the usual Ar 3-2-1 obtained by increasing the maximum temperature to which the material was heated, much has been published1 connecting this phenomenon with a large number of dissimilar steels of high alloy content. From the fact that the transformation divides itself, taking place at two widely separated temperatures, it has been called a "split transformation." The significant facts established by recent investigators2 are: that when the transformation occurs at the higher temperature Ar1, troostite or a decomposition product is formed, and that when the transformation occurs at the lower temperature Ar", the resulting structure is martensite. The terminology Ar&apos; and Ar" adopted here is that of Portevin. Previous Investigations Reviewing the work on this subject published in a recent issue of Revue de Metallurgie and referring in particular to his statement that martensite is a solution of carbide in alpha iron, Le Chatelier says :4 "How then can a theory already 20 years old demand new investigations? The reason for it is that we have not succeeded in proving directly the real presence of the transformation of iron during the very short duration of the quenching. The fall of temperature takes place at the rate of several hundred degrees per second and the observation of

Jan 1, 1920

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda &apos;and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda&apos;s solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky&apos;s thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky&apos;s solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By J. M. Gaines, C. H. Herty, M. W. Lightner, H. Freeman

Few subjects have attracted the attention of metallurgists more than oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction; vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;&apos; furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A12O3, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet extraction methods3 give only the more insoluble oxides SiO2 and A12O3, though the iodine method gives MnO to an uncertain degree (information that may be more misleading than no information

Jan 1, 1930

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

BEFORE me is a colored mining-claim map of the productive portion of the Robinson Mining district-sometimes called the Ruth-Kimberly area-that lies a few miles west of Ely, Nevada. It covers an area of 20 sq mi and at the end of 1954 had produced just under 2,000,000 tons of copper and about 2,000,000 oz of gold as a by-product. The three principal colors on the map and the meaning of each are: Red -Property of the Nevada Mines Division of Kennecott Copper Corporation, formerly known as the Nevada Consolidated Copper Company. Yellow -Property of the Consolidated Coppermines Corporation. Green --Consolidated Coppermines property under lease to Nevada Mines. The striking feature of the map is the crazy-quilt intermingling of the colors and the tendency of property lines to intersect ore bodies. For example, the westerly one-fourth of Nevada Mines&apos; Copper Flat pit, source of most of the ore,up to date, is in Coppermines property. Nearly half of Nevada Mines&apos; Veteran pit is on leased claims; and Nevada&apos;s new Deep Ruth shaft is on a right of way on ground originally owned by Coppermines. On the other hand, the original Ruth underground mine and the new Kimbley pit are on Nevada Mines property; and the Morris and Brooks opencut mines, the most important of Cop-

Jan 1, 1957

By J. H. Clemes

The process of leaching silver ores with sodium hyposulphite is comparatively new, and published accounts of the details and losses of the process are as yet very few. The following account of a careful series of experiments to determine the actual loss in this process may therefore be acceptable to members of the Institute. The ore treated was highly calcareous, and the principal sulphide present was iron pyrites. Following is an analysis by Professor Price, of San Francisco, of the ore treated : Per cent. Silica,..........15.13 Sulphur,.........13.31 Arsenic,.......... 9.82 Iron............ 17.33 Alumina,..........1.35 Zinc,...........4.92 Lead,..........1.78 Carbonate of lime,..33.78 Magnesia,.......... 2.58 100.00 Ten tons were crushed dry with a 30 X 30 screen = 900 holes per square inch. In order to feel our way with this ore, two experimental or "pilot" charges were roasted. Pilot Charge No. 1. Treated 1000 pounds in a four-hearth reverberatory. 8.30 p.m.—Entered fourth hearth, remaining there one and onehalf hours; sulphur began to burn. 10 p.m.—Changed to third hearth; ore became red-hot half an hour after entering; the fireplace was kept almost destitute of fuel. 2.30 A.M.—Changed to second hearth. Charge continued, giving off a large quantity of sulphurous fume; the fireplace was kept dark.

Jan 1, 1884

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 1 1/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond de- lays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face.so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of $5 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock.

Jan 1, 1950

By Esteban Domic, Eugene O. Brimm

The Lo Aguirre ore deposit of Sociedad Minera Pudahuel is expected to have a life of 12 years, producing 16,500 mt per year of copper cathodes. The total copper content of the ore ranges from 2% in acid-soluble form to 2% as sulfides. Sociedad Minera Pudahuel chose TL leaching, solvent extraction, and electrowinning as the processing steps to give low investment and operating costs. Design and operating criteria of the TL leach plant have been obtained in an experimental program carried out since 1974. Bench scale tests indicated that 90% of the oxidic copper and 35% of the sulfidic copper could be extracted to give 5 gpl copper by treating crushed ore with acid, curing, and rinsing in a column with a dilute acid solution containing ferric sulfate which is requllred to solubilize the sulfides. These results were verified in a pilot plant which combined leaching, solvent extraction, and electrowinning. Raffinate was recycled to the leaching circuit after oxidation to regenerate ferric ion. Refinements in the processing have resulted in significant improvements in extraction to give 95% to 98% recovery of the oxidic copper and 55% and 60% of the sulfidic copper. The plant is expected to give this degree of recovery. As a consequence, the original plan to include a concentrator in the plant has been abandoned.

Jan 1, 1980

By C. L. Dake

Chemistry of Iron Solution IRON is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered&apos; soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.1 Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil.4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble

Jan 7, 1915