Search Documents

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Kengo Usui

The energy consumption of Iron-making, especially Blast Furnace (BF), is very large. In order to maximize the utilization of limited resource, it is essential to reduce energy consumption and recovering waste energy in BF. This paper introduces energy saving equipment based on NSENGI’s over 80 BF construction experiences since 1963. The first is the technology for the Top Charging System for low fuel-rate operation. One of the important factors to achieve such operation, the burden should be charged uniformly. Since 1974, NSENGI have developed and delivered over 80 Top Charging equipments for such purpose and nowadays, developed new type Top Charging equipment with improvement of charging precision. The second is the technology for Solely BFG Operation in Hot Stove, which means no use of other fuel gas such as LDG, COG. It is realized by high combustibility of NSENGI’s Top-Combustion Hot Stove with Metallic Burners, and large amount of heat recovery of Waste gas Heat Recovery system with heat medium. The third is the technology for effective energy recovery in TRT. With NSENGI’s latest Gas Cleaning System “Multi-Vessel Electrostatic Precipitator" (MVEP), TRT will be able to generate higher electrical energy by approx. 30% than that of wet-type. In comparison with dry bag-type, MVEP allows temperature fluctuation which lead to generate higher electrical energy by approx. 10% NSENGI therefore, will be able to accept and meet your request widely.

Aug 1, 2018

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Olivier Lacroix, Dubé Mathieu, Guylaine Laforest

The reduction behavior of iron ore pellets in gas-based DR shaft processes has been studied at COREM since the late 80s. At that time, a new DR characterization test called COREM R180 was developped in collaboration with ArcelorMittal Mines Canada (former Quebec Cartier Mining) and ArcelorMittal Long Products Canada (former ISPAT Sidbec Inc.). This paper describes COREM’s approach to improve its understanding of the relations between iron ore pellet microstructure and pellet quality. The differences between the DR90 and the R180 tests are discussed. The evolution of the microstructure during reduction of both tests is also described. The reduction steps during the two tests are put forward as an important factor impacting the microstructural changes as well as the test results.

Oct 1, 2019

By Francisco de Paula Pinheiro

Estudo das fontes de variação do processo de vazamento contínuo de chapas de alumínio, através da aplicação de uma metodologia prática e rápida para solução de problema. Após identificação das variáveis críticas à qualidade, ações foram tomadas de modo a minimizar as perdas do processo, o que contribuiu para a redução nos custos de produção das chapas.

Aug 16, 2017

By Jose Maria Rodriguez-Ibabe, Ronaldo Antonio Neves Marques Barbosa, Douglas Glenn Stalheim

Major costs in the production of both flat and long commodity grade structural steel products include alloy, labor and energy. Flat and long commodity grade structural steels such as ASTM A36, ASTM A527Gr50, S235, S275, S355 and other equivalent world societal standards represent over 500 million annual tons worldwide. These simple commodity grades consist of a minimum of three base common alloying elements, carbon, manganese, silicon and then can be supplemented with microalloying elements of either vanadium or niobium. Since 2016 raw material costs for two of the five alloying elements in these commodity grade structural steels, FeMn and FeV, have risen significantly and/or have become volatile making it difficult to maintain stability in profitability for these commodity grades. For steel plants producing hundreds of thousands and in some cases over a million tons annually of these common structural steel grades because of the significant alloy cost increase for Mn and V alloy additions has squeezed profitability of these grades. These grades typically represent the base loading for cost controls in most all steel plants and hence a significant cost increase or volatility in two of the five elements used for these grades having a negative effect on overall production costs. However, with a proper strategy for alloy designs working in conjunction with the mills existing processing capabilities to achieve the desired end metallurgy/mechanical properties, alloy costs and operational efficiencies can be realized.

Oct 1, 2019

By Wolfgang Kern

The implementation of the Gas Treatment Plant (GTP) for CSPECEM, Ceara-Brazil is a result of the closed partnership between Paul Wurth Italia S.p.A. and DMT, the German leading company in Coke Oven Gas Treatment Plants. In addition to technical issues reducing emissions, avoiding of waste and saving environment and energy were technical challenges during the engineering phase. Below mentioned three descriptions of technical solutions represents examples of a number other innovations based on DMT’s know-how and experience in the field of by-product plants. Generally the design of the complete GTP is based on the consideration of modern features and design upgrading, with the aim of a safe operation with stable conditions and a long-living cycle of the whole of the plant.

Aug 16, 2017

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017

By Juergen Meisel

The paper will explain how to successfully implement a robotic solution from the initial idea to a working industrial solution. Primetals Technologies can call upon 10 years of experience in installation of Robot solutions in the harsh environment of steelmaking plants - the so-called LiquiRob. To enhance an existing shroud manipulation system, the idea to connect the shroud with a bayonet mechanism to the ladle nozzle was born in accordance with the requirements of a well-known steel producer. The paper will describe the development steps from the first simulations and prototype testing in the laboratory, it will show the intensive system testing under workshop conditions and will finally depict the successful integration into the plant. Furthermore, operational experience will be shown as well as the advantages of such an installation compared to other shroud manipulation systems.

Oct 30, 2017

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Jörg Thomasberger

Delivering liquid steel to a steel processing unit at right temperature is an important criterion for high production steel shops, but it is surprising how little attention has been paid in the past to manage this vital phase in the steelmaking process-the steel in transit. The ladle running costs, both directly and indirectly, contribute significantly to the cost of steelmaking and should be an area of concern to any high production steel plant. Here we are talking not only of refractory costs or preheating fuel costs, but also cost of extra heating in ladle furnace, additional process delays incurred in delivering steel at right temperature to downstream unit in case proper care is not exercised at upstream unit, and occasional costs of ladle breakout due to inability to judge the residual life of the ladle. This paper emphasizes the need of a comprehensive ladle management system, an aspect which has not been properly addressed in the operations of a steel plant, in improving the productivity of a steel melt shop. Starting with review of present status and the attempts at implementation of ladle tracking in steel melt shop automation system, it looks at components of an exhaustive Ladle Management System (LMS), and finally gives an idea of benefits that will accrue from implementation of such a system in a steel melt shop.

Aug 17, 2017

By Michael Brandner

In the past the research and development of new materials for hot mill rolls was mostly done by trials. Such trials are expensive and difficult to transform from small size to the big size of a solid roll. Computation is the cheaper way to get ideas processed and can be varied in different directions. The main part before simulation is the generation of the needed basic data of the specific materials. Some data is already well known and can be bought from databases; others have to be done specifically for our materials. The evaluation of such results has to be done still with solid trials, but the number of trials can be reduced. The advanced techniques of finite element calculation offer a wide range of possibilities to get answers about alloys, solidification, casting parameters and their influence. The possibility to calculate a heat treatment cycle and to get an answer about the internal stress modification during the cycle is a great help to understand the principle of transformation. Examples of different calculations in various fields will be given. The close cooperation with universities and other research institutes as well as the in-house possibilities will be presented.

Jul 30, 2018

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Kenneth Williams

Economic drives dictate the exploitation of formerly less attractive ore bodies located close to or even beneath the water table. These ores can cause handling problems and expensive downtime of processing equipment due to their increased adhesive characteristics and are colloquially termed as “wet and sticky” ores. In order to gain a better understanding of the causes of poor handleability, experimental test methods for wall and inter-particle adhesion within bulk solids samples were developed and validated. The results confirmed that adhesion of bulk solid to equipment surfaces is mainly governed by capillary pressure. It can therefore be described using the Young-Laplace equation, which implies that adhesion is primarily dependent on the interfacial water between bulk material and the adhesion partner. Accordingly, the governing material parameters of adhesion are its capillarity and permeability, as these two characterize water transport to or from the interface of the adhesion partners. Furthermore a threshold for the classification of a material as wet and sticky based on the measurements of adhesion has been proposed.

Aug 17, 2017

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By Alberto Tremea

In this period a great attention is put on roll cost and the differences in roll behavior in very few situations move the existing balances. Among many variables that are taken into account to evaluate the roll there is the consumption which is normally calculated according to the tonnage rolled. In this work there is a review of some approaches that are used to evaluate the roll efficiency together a description of a new method to make this. The main purpose of this calculation method is to help the comparison of roll results used in different mills. There is the need to have a clear and univocal reference when it’s time to think about innovative products. At now there are available roll grades with excellent technological properties but it’s necessary to have the right tools for a careful evaluation of roll behavior to take a good decision.

Jul 30, 2018

By Adriana Amaro Diacenco

This work presents the finite element modeling of Euler-Bernoulli beams constituted of a metallic material, discussing theoretical and numerical aspects. The numerical analysis uses Hermitian interpolation functions and finite elements with two degrees of freedom per node. A numerical simulation will be done for uniform loading considering two kinds beams (steel and aluminum). The paper is organized as follows: introductory comments and numerical simulations to evaluate the static and dynamical behavior of the metallic beams.

Aug 7, 2018

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017