Search Documents

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By P Jones

Fosterville Gold Mine is an underground operation located approximately 20 km northeast of Bendigo and 170 km north of Melbourne. Fosterville is the most productive gold mine in Victoria, producing over 100 000 ounces of gold annually. Access to the underground is via two portals cut into previously mined open pits. Fosterville is 100 per cent owned and operated by Northgate Minerals, a gold and copper producer with mining operations, development projects and exploration properties in Canada and Australia. (Northgate Minerals Corporation, 2010).Underground operations commenced in 2006 with ore production focused on three orebodies – Phoenix, Ellesmere and Falcon. Primary ventilation to the existing operation is provided by wall mounted exhaust fans located underground. This system provides approximately 220 m3/s of primary ventilation to the operations with intake achieved through the portals. Exploration drilling during recent times has uncovered another lode, the Harrier orebody, located 2.2 km to the south of the existing workings. Due to the location of the new Harrier orebody, vent analysis revealed the requirement for a separate source of primary ventilation to service Harrier. Figure 1 shows a current underground long section and the location of Harrier in relation to the existing workings. A number of options were considered, including a parallel decline from one of the existing two portals, however, a 4 m diameter, 350 m deep surface ventilation shaft was selected as the most suitable and feasible option for the mine.In December 2009, geotechnical drilling commenced to determine the most suitable location for the shaft. Site locations were constrained by a number of factors including interaction with current and planned surface infrastructure as well as proximity to nearby community members at the southern end of the mining lease. Results from the geotechnical drilling indicated that the majority of the proposed shaft would be suitable for a 4 m raise bored shaft. However, the top 40 m of the proposed shaft were deemed unsuitable for raiseboring due to zones of weakness that would likely influence the stability of a 4 m diameter shaft (Robinson, 2010). Following independent geotechnical advice and input from experienced raiseboring contractors, it was decided to construct a 40 m presink prior to raiseboring activities.A crane mounted auger was chosen as the preferred method to construct the presink. This method differs substantially from traditional blind sinking methods which are highly labour intensive. The auger, or drill, is designed and built to be attached to a crane base using engineered pivoting cradles. The auger is suspended from the crane jib by pennant ropes attached to hydraulic rams. The auger applies rotation and axial loads to the drilling tools via a telescopic steel bar (Kelly Bar). Drill tools are attached to the bottom of the Kelly Bar and comprise an assortment of drilling buckets and reaming barrels. Drilling buckets cut in situ material and collect the spoil for removal and are used for the excavation of the ‘pilot hole’. Reaming barrels are used to expand the diameter of the excavation by directing cuttings into the pilot hole which are then removed by the drilling bucket. In June 2010, the presink was constructed utilising a crane mounted auger with support to the shaft walls applied via a remote fibrecrete unit. The excavation method involved cutting a series of smaller diameter holes (2.4 m wide) before reaming out to the final diameter (4.7 m wide) in 4 - 5 m vertical increments. Fibrecreting activities were carried out on the backshifts, to ensure the stability of the excavation and minimise interaction between the two units. The presink was completed on time and offered many advantages compared to traditional blind sinking methods, including safety, costs and timing. This paper will examine the benefits of this method as well as lessons learnt and future applications in the mining industry.

Mar 21, 2011

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By Michael R. Norland

Surface and subsurface stabilization of mining-related wastes through revegetation depends upon the physical, chemical, and biological condition of the waste following mining. Mining disturbances can significantly alter the soil physical, chemical, and biological characteristics of a site, reducing or eliminating mycorrhizal fungi from the soil. Mycorrhizae are economically and ecologically important because they can alleviate environmental stresses caused by lack of proper soil condition and because they are vital to stabilization of mining waste by increasing plant survival and biomass through increased nutrient and water uptake. This report discusses some of the ecological factors that may affect mycorrhizae-plant associations on mining-related wastes and provides general information on mycorrhizae inoculation technology.

Jan 1, 1993

By Laurence A. Dahners

As part of the strategic minerals program, the Bureau of Mines conducted a diamond-drilling project on three barite properties in eastern Tennessee and western North Carolina during the summer and fall of 1944. These properties, the Moccasin Gap prospect and the Krebs property in Cocke County, Tenn., and the Sandy Bottom mine of the Stackhouse group in Madison County, N. C. (fig. 1), are known to have produced some barite. The Bureau of' Mines project was planned to prospect for extensions of the ore bodies. A total of 3,169 feet of diamond drilling was done in 15 holes on the three properties. Tabulations of sample analyses and drill-hole logs are presented in this report. Two other mines of interest in the area are the McCoy and the Williams in Cocke County, Tenn. The Williams adjoins the Krebs. No drilling was done by the bureau in either of these properties.

Jan 1, 1949

By The Staff

"IntroductionThis paper lists typical liner performance data for various grinding mills at the Noranda, Waite-Amulet, Pamour, and Hallnor mines, and concludes with a comparison of these data, based on wear per square foot of lined mill shell area. Flow-sheets for each of these plants will be found in the reference cited.General InformationTwenty-eight ball-mills and one rod-mill are used by the Noranda organization for grinding ore. These mills, which are shown in general outline in Plate IV, are all of the overflow type and have a cylindrical shell attached to dished heads.Most of them are serviced by hand-operated cranes and none by power cranes. During re-lining, portable tugger hoists are employed to lift the liners and, frequently, to install them in place.The mills vary in length and diameter and the ratio of end liner area to breast liner -area consequently ranges from 1. 6.75 in a 5 ft. by 14 ft. mill, to 1:2.28 in an 8 ft. by 8 ft. mill."

Jan 1, 1950

Jan 1, 1990

By Paul Sterling

1. INTRODUCTION. THE general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a "coal-breaker." This name is misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only in the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for domestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Oct 1, 1911

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

The Particulate Mineralogy Unit has been established at the College Park, Maryland, Metallurgy Research Center. The Particulate Mineralogy Unit will have the responsibility within the Bureau of Mines for the characterization of particulate minerals which have potential for adverse environmental effects. The Unit will provide a focal point for identifying particulates in connection with environmental problems related to the activities of agencies such as OSHA, HEW, EPA, and MESA. The Particulate Mineralogy Unit is seeking to clarify the ambiguities surrounding the mineralogy of and terminology used for asbestiform minerals and other mineral particles. The Unit?s investigations of the morphology, composition, and structure of asbestiform minerals and their nonasbestos analogs have made its members recognized experts in this field. The information which it develops on the characterization of asbestos and other particulate mineral forms such as silica should provide a technically rational basis for decisions by regulatory agencies. Those desiring further information, contact Dr. W. J. Campbell, Program Coordinator, College Park Metallurgy Research Center, College Park, MD 20740, telephone: 301-344-4014. ALUMINUM: For over a month, domestic producers have priced 99.5 percent grade primary aluminum ingot at 48¢ per pound. In the same period, merchants raised ingot quotes by 1.5¢-2.5¢ to a range approaching 44¢-47¢ per pound.

Jan 1, 1976

By V. R. Shea-Albin

This U.S. Bureau of Mines report discusses elastic wave velocity and attenuation behavior as an indicator for changes in load and structural integrity of coal samples. Measuring changes in compressional (P)-wave and shear (S)-wave attenuation and velocity under uniaxial and triaxial compression tests revealed their effectiveness for distinguishing changes in applied load and structural failure of samples. The velocity and attenuation values were used in further calculations such as ratios of P-wave to S-wave values, dynamic elastic constants, normalized velocities, and attenuation coefficients to reveal trends for loading and failure. The behavior of both P-wave and S-wave attenuation and velocity together define distinct and consistent phases of load change and failure for uniaxial and triaxial tests. The S-wave velocity and attenuation illustrate changing axial load and initial development of microfractures within the sample preceding structural failure more clearly than those of the P-wave. The attenuation and velocity ratios and dynamic elastic constants (except the bulk modulus) respond to closure of small preexisting fractures within the coal sample with initial loading to failure of coal samples. The attenuation coefficients and normalized velocities reveal trends similar to those shown by velocity and attenuation.

Jan 1, 2010

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976

Research 86 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1986

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

By Davis E. Traut

TiC14, AIC13, and VC14 were coreduced simultaneously via a Kroll-type magnesium reduction to form an alloy sponge as part of a research effort by the Bureau of Mines to produce titanium alloy powder. Reduction tem-peratures of 750°, 850°, and 950° C, a range of chloride feed rates from 34 to 152 Ib/(ft2·h), and crucible diameters of 7-3/4 and 10-1/4 in were tested. Microprobe analyses using a 40-um-diam spot showed no effect on alloy microhomogeneity (distribution of Al and V in the Ti, considered critical as a powder property), due to changes in process variables within these ranges. Statistical analysis of these data for alloy sponge indicated greater variation in the chemical composition (AI and V) than that found in commercial Ti-6Al-4V plate or Plasma Rotating Electrode Process (PREP) powder. Therefore, a one-step approach to pow-der, such as grinding the Ti alloy sponge, would not produce a powder product of acceptable chemical homogeneity. An approach that homoge-nized the sponge, such as with a melting step, would produce an accept-able powder product with respect to chemical homogeneity.

Jan 1, 1987

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

By Urs Peuker, Thomas Mütze, Thomas Leißner, Inga Osbahr

"Mining in the Ore Mountains (Germany) has taken place for hundreds of years and in several stages. Each stage produced its typical tailing. According to the former state of the art of the processing much valuables could not be extracted. This was caused by complex interlocking of the minerals, low grades, or by upgrading processes not sensitive enough for small particle sizes. Thus the processing of these fractions was uneconomically. Modern technical possibilities and rising metal prices bring these tailings disposals into focus for the processing of strategic metals. Mining disposals can be classified in heaps with coarse, low grade rock, which did not undergo a processing, slags and fly ash from smelting, and tailing disposals from mineral processing. The latter is under investigation to integrate them into a geographic information system. The mineral processing of the material will be part of the database besides information about geographic location, structure, amount of valuables, and details of ownership of the heap. The tailings disposals are composed of coarse, low grade, interlocked particles from density separation processes, medium size particles, which are tailings from flotation, and fines with liberated valuables, which did not undergo flotation. Therefore mineral processing of these disposals comprises the separation of liberated gangue by classification, beneficiation of locked valuables with density separation, liberation of valuables by grinding, and beneficiation of liberated valuables with flotation. The presented work shows the results concerning the composition of one exemplary heap and results of the classification as well as of the preconcentration tests achieved with material from this heap."

Jan 1, 2014

By David White

This paper is the result of a comparative study of ultimate coal analyses made and published by the United States Geological Survey. This study, at first casually undertaken to devise an acceptable classification of coals based on chemical analyses, was continued in connection with a microscopic examination of a number of the coals. The initial comparisons, made from a relatively small number of analyses, not only confirmed a previous conviction that the elimination of oxygen incident to the development of a coal is economically far more important than has been generally suspected, but also showed that oxygen is very nearly as harmful as ash in coal. The immediate purposes of the present study were: (a) To determine more definitely, from a comparative examination of a large number of ultimate analyses, the relative importance of oxygen as an impurity in various coals; (b) to illustrate the transition between various grades of coal of similar origin-transition mainly due to progressive devolatilization, brought about more or less directly by dynamic influences; (c) to ascertain the relative proportions of oxygen, hydrogen, and carbon in coking coals, especially with reference to a theory tentatively framed to explain the coking quality; and (d) to forecast the probabilities of successfully treating a large number of coals so as to render them amenable, in a softened condition, to satisfactory study under the microscope.

Jan 1, 1911

By S B. Richardson, D Mead, N T. Moxon

The use of air-decks to reduce explosive costs has become very topical in recent years. The majority of the research in this area has been arried out between the Soviet Union where reductions in explosive consumption of between 10-30% have been claimed with apparent benefits being gained in both fragmentation and movement. Work carried out by the University of Maryland using thick plexiglass blocks has supported these findings and indicated that air-decks in measetbe duration of action of the shock wave on the surrounding material by a factor of 2 to 5 (see Figure 1). Although the fracture network resulting from this mechanism is not as intense as that produced adjacent to the explosive charge it does appear to act over a larger volume of material. Although the mechanism attributed to air-decking has been studied in some detail the effect of this mechanism on the size distribution of material produced during a blast does not appear tot have attracted much attention.

Jan 1, 1991

By J. F. Neill, O&apos

[The Cartersville mining district is in Bartow County, Ga., about 40 miles northwest of Atlanta. Barite, limonite, ocher, amber, hematite, and, manganese oxide ores have been produced from the strict since about 1840. In the search for a possible source of manganese ore, Bureau of Mines engineers made a preliminary study of the district from September 1950 to January 1951. During this study 139 deposits were examined, and many mineral exposures were sampled. Manganese mineralization occurs as fine oxide and concretionary pellets in residual clays, as fine oxides in umberous clay, in brown-iron deposits, and in a limited quantity in mud ponds and Jig-tailing piles. The future supply of ferrograde manganese ore from the district, using current mining and benefication methods, appears limited to the recovery of the hard manganese ores deposits. Rough estimates indicate a reserve of manganese-bearing clays of about 8,000,000 long tons. This type of deposit has been extensively exploited and the larger deposits mined out to depths of from 50 to 200 feet. The remainder of these deposits are low grade, are covered with deep layers of colluvium, or lie below the ground-water table. Any future production from this source will require systematic prospecting, improved concentration, and an increase in the price of concentrate.]

Jan 1, 1954