Search Documents

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

Laboratory trials were performed in an induction furnace to study droplet formation during lance blowing. Compressed air was blown on a molten iron bath consisting of iron alloyed with carbon and silicon. Steel droplets were collected using a specially designed sampler. The average steel droplet composition and the oxide layer thickness were determined using scanning electron microscopy combined with energy dispersed spectroscopy. In addition, the concentration gradient of elements was determined using a microprobe. It should be noted that a special technique had to be developed in order to prepare the droplet sample. The size distribution and composition of the droplets was also determined using the microprobe. It was found that the carbon content in the droplets was lower than the carbon content in the bulk.

Jan 1, 2006

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

The early history of the mine is traced from the beginning of shaft sinking in 1886 to the purchase by the Broken Hill Proprietary Co. Ltd. in 1949. A necessary preliminary to mechanisation of the Borehole Seam was development of the Young Wallsend seam, andthis development is described. Surface reorganisation and coal handling arrangements are dealt with in detail. Then follows a description of the Borehole Seam mechanisation, the provision of power supply for this purpose, arid pumping arrangements in themine.INTRODUCTIONStockton Borehole Colliery is in the Parish of Teralba, between the townships of Teralba and Boolaroo, and about 12 miles from Newcastle. The colliery holding, a freehofd area of 2,560 acres, was apparently an original land grant when acquired by Teralba Co-operative Coal Company who decided to mine for coal and named the mine "Teralba Colliery." Shaft sinking was commenced in 1886 but was delayed by financial and water troubles to such an extent that it was not until 1901 that the Borehole Seam was reached.Coal was won until 1904 using a single 16 ft. diameter shaft, ventilation being achieved by means of a wooden boxing down one side of the shaft. This collapsed, and operations ceased until the mine was taken over in 1906 by a company known as "Borehole Colliery Limited," the principal stockholder being the Stockton Coal Company. It renamed the mine "Borehole Colliery." This new company immediately commenced sinking a 13 ft. diameter air shaft. In 1908 the Stocktol1 Colliery at Stockton was abandoned, and during the following year much of its equipment was transferred to Borehole Colliery. The name was again changed becoming "Stockton Borehole Colliery." From this period on, coal was produced from the Borehole Seam by...

Jan 1, 1957

Jan 1, 1994

Remote sensing, in general, is the recording of light and heat from a planet's surface within a certain range of the electromagnetic spectrum. For the Earth, systems capable of this recording are the MultiSpectral Scanner (MSS) and SLAR. The former is the recording system used in satellite and will be discussed in the next section. SLAR stands for Side Looking Airborne Radar. This device sends invisible radar waves which illuminate the Earth's surface. The reflected waves are subsequently recorded as images. The system can operate through darkness and dense cloud cover, and is particularly suited for the study of geological structures at both large and small scale (Wayland 1976). Remote sensing techniques are now widely being made use of in mineral exploration, especially for those last remote 'sanctuaries' where geological data are meagre or non-existent. For places like Borneo, West Irian, the Amazon Basin etc. remote sensing, in the form of both satellite imagery and SLAR, is of considerable help, in fact more often than not the only help, to delineate geological provinces, geotectonic domains and meaningful lineaments. In the case of New Zealand, well made geological maps at scale 1:250 000 by the Geological Survey are available to the public and these provide useful preliminary grounds for the selection of target areas. However, even in this case LANDSAT imagery can be of aid as will be shown later.

Jan 1, 1977

By M. Ghoreychi, X. Daupley

ABSTRACT: The paper is devoted to two major aspects related to the abandonment of salt mines: 1)- Long-term risk associated with the mechanical instability of surface and its consequences for public security and properties. 2)- Long term dissolution and transport of salt resulting from its communication with groundwater. Basic characteristic features of salt deposits and mining methods are presented through the studies already undertaken on French mines. This analysis allows to identify major hazards encountered in different traditional salt mines and solution-mining cavities. In particular, the role of overburden (presence and thickness of salt layer in exploitation roof, presence of clayey rocks or hard rocks e.g. dolomite or anhydrite), presence of water-bearing strata and possibly natural brine levels, discontinuities, etc. are discussed. In the second part, the main features of mechanical behaviour of salt (creep, damage) as well as transfer processes of this material are presented. The influence of these aspects on the long term evolution of abandoned salt mines is then analysed. KEY WORDS: exploitation, abandonment, salt, mechanical, stability, transport, solution, brine. ZUSAMMENFASSUNG: Der Artikel bezieht sich auf zwei bedeutende Aspekte beim Salzabbau: 1)-Das langsfristige Risiko zur Bodenoberflächeunbeständigkeit und sein Einfluss über Mensch= und Gütersicherheit. 2)-Die langsfristige Auflösung und Beförderung des Salz beruhen sich auf Studien über französiche Bergbauen. Diese Analyse emöglicht es, die bedeutendesten Risiken in verschiedenen Salzgruben zu identifizieren, bzw. Traditionellen oder durch Auflösung abgebauten. Insbesondere wird die Rolle des Deckgebirges (Vorhandensein und Dicke von Salzschicht am Dach des Grube, Beisein von Tanlager oder hartem Gestein wie Bitterkalk oder Anhydrid), Beisein von wasserhaltigem Boden und/oder gesalzenen Wasserflächen, Trennflächen, usw… erötert. Im zweiten Teil werden die haupsächlichen Eigenschaften des Salzverhaltens (Kriechen und Beschädigung) beschrieben. Ihr Einfluss über das Verhalten von stillgelegten Bergwerken lässt sich analysieren. SCHLÜSSELWÖRTER: Bergwerksbetrieb, Stilllegung, Mechanik, Beständigkeit, Ausbreitung, Aussolung, Solewasser. RESUME: L’article est consacré à deux aspects majeurs liés à l’abandon d’exploitations de sel : 1)- Le risque d’une instabilité à long terme de la surface du sol et son incidence sur la sécurité des personnes et des biens. 2)- La dissolution à long terme et le transport de sel sous l’effet d’une communication avec des eaux souterraines. Les principales caractéristiques de gisements et d’exploitations de sel sont présentées en s’appuyant sur les études antérieures réalisées sur les exploitations en France. Cette analyse permet d’identifier les risques majeurs rencontrés dans différentes mines de sel traditionnelles ou exploitées par dissolution. En particulier, le rôle du recouvrement (présence et épaisseur d’un banc de sel au toit de l’exploitation, présence de terrains argileux ou de roches dures telles que la dolomie ou de l’anhydrite), présence de terrains aquifères ou de nappes salées éventuelles, discontinuités, etc. sont discutées. Dans la deuxième partie, les principaux traits du comportement mécanique du sel (fluage, endommagement) ainsi que les processus de transport de ce matériau sont présentés. L’influence de ces aspects sur le comportement à long terme d’exploitations abandonnées de sel est ensuite analysée. MOTS CLES: exploitation, abandon, mécanique, sel, stabilité, transport, dissolution, saumure.

Jan 1, 2003

Recovery of Tantalum Capacitors from Waste Printed Circuit Boards Using a Pneumatic Separator

Sep 13, 2010

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

By H. Britton

This bulletin is the seventh in the series of petroleum bibliographies published by the Bureau of Mines, Bulletins 149, 165, 180, 189, 216, and 220 being compilations for the years 1915, 1916, 1917, 1918, 1919-20, and 1921, respectively. In this bulletin the same general plan of classification of references has been followed, but several additions have been made. ACKNOWLEDGMENTS Acknowledgment is made to the following organizations for the use of their libraries in the preparation of this bulletin: University of California, Stanford University, California State Mining Bureau, Union Oil Co. of California, Standard Oil Co. of California, and the Mechanics Mercantile Library of San Francisco; acknowledgment for their assistance is also made to H. H. Hill, C. P. Bowie, A. L. Foster, M. J. Gavin, H. C. Miller, E. B. Swanson, and Miss Louise Janssen, all of the Bureau of Mines, and to Miss Elizabeth H. Burroughs of the Union Oil Co. of California.

Jan 1, 1929

By João Carlos Jânio Gigolotti

O avanço tecnológico tem gerado demanda crescente por materiais que possam ser utilizados em alta temperatura e ambientes oxidantes, o que inclui ligas intermetálicas MR–Si–B (MR = metal refratário) com estruturas multifásicas. Assim, este trabalho teve por objetivo estudar a microdureza de ligas do sistema Hf–Si–B na seção isotérmica a 1600ºC, na região rica em Hf. Ligas Hf–Si–B foram fundidas com lâminas de Hf (min. 99,8%), Si (min. 99,998%) e B (min. 99,5%), em forno a arco e tratadas termicamente a 1600 ºC em atmosfera de argônio. As relações de fases nessas ligas foram identificadas por difração de raios-X e por contraste, em imagens obtidas via microscopia eletrônica de varredura no modo elétrons retroespalhados. As ligas tiveram sua dureza medida pelo método Vickers (microdureza) com cargas de 0,05 kgf e 0,2 kgf e tempo de aplicação de 20 s. Os resultados, obtidos da média aritmética das medições realizadas nas regiões heterogêneas de cada liga, mostraram uma dureza média de 11,08 GPa, com pequeno coeficiente de variação de 3,8%. Os boretos HfB2 (19,34 GPa) e HfB (11,76 GPa) apresentaram dureza mais elevada que os silicetos Hf2Si (8,57 GPa), Hf5Si3 (9,63 GPa), Hf3Si2 (11,66 GPa), Hf5Si4 (10,00 GPa), HfSi (10,02 GPa) e HfSi2 (8,61 GPa).

Aug 17, 2017

By A N. Danoucaras, S E. Goater, D Hearne, A M. Bansuan

It is globally recognised that existing and emerging mining activities should be conducted in a æsustainableÆ manner for the entire life of mine. Many companies annually publish corporate sustainability reports to demonstrate their actions in accordance with international expectations. This concept of sustainable mining practices also applies to mine water management, with influences often extending beyond site operations, affecting surrounding catchments and community users. This paper explores differences in conceptual and operational terms of æsustainableÆ mine water management within the Philippines. Outcomes of a review of corporate sustainability reports, governance documentation, research programs, and stakeholder knowledge acquired through action-research workshops are presented. The paper aims to inform and support future capacity building exercises delivered by the International Mining for Development Centre (IM4DC), with outcomes tailored to government officials and policy makers of developing countries. The project is funded by IM4DC, which is working with AusAID to identify needs and develop capacity with regard to mining for development; specifically, issues pertaining to governance and regulation, social and environmental sustainability, and operational effectiveness in developing countries.CITATION:Bansuan, A M, Goater, S E, Danoucaras, A N and Hearne, D, 2012. Integrated sustainable water management in mining for development in the Philippines, in Proceedings International Mine Management 2012, pp 205-226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Gupta R. C

Syria has about 500 million ton deposit of minerals having 34 per cent iron content with alumina and silica as major impurities. Efforts were made to see the feasibility of concentration by four different methods involving washing, high intensity magnetic separation, reduction roasting and magnetic separation and acid leaching technique. It was observed that the reduction roasting with magnetic separation yields a concentrate with high iron (62.3 per cent) content without requiring water which is a scarce raw material in the region. The paper concludes that the detailed study may be made following this route to optimise the process Parameters.

Jan 1, 1999

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

IN this paper it is proposed to present certain features of operating practice at the Port Pirie works of The Broken Hill Associated Smelters Proprietary Limited, in the smelting in a blast furnace of lead ores carrying a high concentration of zinc.The subject matter selected for presentation is:(i) The effect of zinc on lead blast-furnace operations, together with an outline of the methods adopted in actual practice in dealing with the zinc problem.(2) Development of the height of tuyere above the bottom of the jacket, and the extension of the tapping interval and the combined effect of both factors upon the lead content of blast furnace slag.It will later be seen that one phase of the investigation carried out in connection with the effect of zinc on blast-furnace operations was largely responsible for the decision to increase to a marked degree the height of the tuyere above the bottom of the jacket.Due to this interdependence, it has been considered advisable to deal with the two features above mentioned.The high concentration of zinc in the lead-bearing materials smelted at Port Pirie has brought with it those troubles which are associated with zinc in the smelting operation.In the early stages of the history of The Broken Hill Associated Smelters Pty. Ltd. the trend towards increasing cost for labour, fuel, and stores, etc., rendered it necessary to increase the lead content of the charge, and reduce to a minimum the quantity of barren flux used.

Jan 1, 1931

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

Jan 1, 1902