Search Documents

By Guilherme Duarte Moreira

Com o objetivo de melhoria dos resultados de desempenho operacional identificouse uma oportunidade em reduzir o tempo de trocas programadas (Setup) na Laminação de Fio Máquina na Usina Siderúrgica de Ouro Branco. Utilizando a metodologia SMED (Single Minute Exchange of Die), obteve-se grande redução do tempo de Setup. Como esta metodologia já se demonstrou uma excelente ferramenta para redução dos tempos de setups, foi idealizado uma abordagem mais completa, sendo desenvolvido um modelo para aplicação para as paradas programadas para manutenção. Esta aplicação corroborou um enorme ganho, tanto na definição do tempo de parada programada, quanto no planejamento e padronização das atividades.

Aug 16, 2017

By C. E. Williams

THE Iron and Steel Division, A.I.M.E., is unique in this country in that it serves all phases of the iron and steel industries. Through its publications, its meetings, and its sponsorship of new technical developments in the industries, it has proved of great value. The various technical committees of the Division are the nucleus around which this service can be developed. The Blast Furnace and Raw Materials Committee has done excellent work. The need for beneficiation of iron ores is increasing and the economics of this operation are developing more and more in favor of increased activities. Ores that are slightly undergrade should be concentrated up to grade to supplant the present practice of mixing with higher-grade ores to bring up the average composition. Marginal ores that are not now being mined, or that are being mined and piled for future use, should be concentrated. The development of the use of sinter in the blast furnace, because of the elimination of fines, the advantage of better sizing of the charge, the resulting reduction of coke consumption, and increased output of pig iron per furnace, will make concentration and sintering become practical ahead of its natural time.

Jan 1, 1936

By D. A. Kramer

Ammonia, the principal source of fixed nitrogen, was produced by 16 companies at 31 plants in the United States during 2003. Fifty-five percent of U.S. ammonia production capacity was centered in Louisiana, Oklahoma and Texas because of their large reserves of natural gas, the dominant domestic feedstock. Production In 2004, U.S. producers operated at about 59 percent of their rated capacity. The United States remained the world’s second largest ammonia producer and consumer following China. Urea, ammonium nitrate, ammonium phosphates, nitric acid and ammonium sulfate were the major derivatives of ammonia in the United States, in descending order of importance.

Jan 1, 2005

By R. L. Virta

Sixteen companies mined fuller’s earth in 11 states during 2004. Production during 2004, based on a preliminary survey of fuller’s earth producers, was 3.96 Mt (4.3million st) valued at $340 million. This compared with3.6 Mt (3.9 million st) during 2003, valued at $346 million. The 3.96 Mt (4.3 million st) probably includes some crude clay tonnage. And production of finished product probably was closer to 3.2 Mt (3.5 million st) in 2004. Georgia was the leading producer state of attapulgite-type fuller’s earth, followed by Florida. Georgia also was the leading producer state for montmorillonite-type fuller’s earth. It was followed, in descending order, by Mississippi, Missouri, Florida, Virginia, Illinois, California, Tennessee, Kansas and Texas.

Jan 1, 2005

By Paul C. Hyndman

No minerals have been produced from the McGraw Creek RARE II area. During the 1982 U.S. Bureau of Mines study, there were no active mines in the area. Limestone occurrences (fig. 1, no. 2), four copper prospects (fig. 1, no. 1, 4, 5, 6), and a prospect with no significant mineral values (fig. 1, no. 3) were examined. A moderate potential for high-calcium limestone resources was estimated between ocurrences within the study area near McGraw and Spring Creeks (fig. 1, no. 2). There is low potential for copper resources at the Argenta Prospect (fig. 1., no. 1) in the study area, and the McDougall Prospect adjacent to the area.

Jan 1, 1983

By Manuela Arend Prediger

Este trabalho teve como objetivo desenvolver um banco de dados com ênfase em materiais semicondutores e condutores para disponibilizar informações dos quatro principais grupos de materiais: metais, compósitos, cerâmicos e polímeros. Isto foi realizado através de uma seleção de materiais e definição de quais os mais adequados à área de semicondutores. Por intermédio de levantamentos bibliográficos em livros, periódicos e sites, foi possível compilar as características e as aplicações destes diferentes tipos de materiais. Assim, obteve-se um site que contém informações precisas e confiáveis e que está disponível àqueles que possuem interesse nesta área. Infere-se a partir do trabalho feito que o uso de materiais semicondutores faz-se cada vez mais necessário e crucial para satisfazer as exigências de equipamentos eletrônicos.

Aug 16, 2017

By JOHN JANNEY

STABILIZATION of the adjustment of normal consumption to normal production of world commodities is quite different from reducing production until visible surpluses are consumed. The first means restoration and maintenance of prosperity, the second means merely a temporary alleviation of a condition with the prime cause remaining uncorrected. Overproduction of foodstuffs in some sections of the world while millions starve in other sections represents not so much overproduction of foodstuffs as mal-distribution of foodstuffs. The flour mills of Washington and Oregon normally ship quantities of flour to China. Now, the wheat that would make this flour goes East instead of West. Is this overproduction, or is there something wrong that calls for study, analysis and correction? Can the plan used by the ostrich of hiding its head in. the sand get us by this present world tragedy, or must the challenge to solve this problem be met, constructively? Can we not make out of this breakdown in the world's economic system an opportunity? And use it as the stimulus for remedying the basic cause of the trouble and not content ourselves with devising temporary expedients that aim at remedying this or that of the obvious conditions, in themselves not causes at all but rather the evidence of causes, or that are the symptoms of the real trouble.

Jan 1, 1931

By Ernest W. Johnson

Diamond, drilling of some blast holes in stoning operations is practised in at least two iron mines in the Lake Superior district - the Soudan mine of the Oliver Iron Mining Co., on the Vermilion range at Soudan, Minn., and the Anvil-Palms mine, operated by Pickands, Bather & Co., on the Gogebic range at Bessemer, Mich. Diamond drilling, at the Soudan nine has partly replaced percussion drilling because of the extreme hardness of the ore and of the lean formation. According to Wolff,4/ the jasper or lean formation in this mine is the hardest rock regularly drilled in any commercial operation.

Jan 1, 1945

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

By Jose A. Gomez, Javad Sattarvand

Failures of tailings dams have been happening lately. Due to the lack of laws on particular design criteria and stability requirements related monitoring during construction and maintenance, they are thought to be more fragile than hydraulic dams. Monitoring the dam is therefore necessary to understand its current condition and guarantee its safety. The physical condition of the dam could be evaluated with the early identification of seepage. Additionally, due to their adaptability and capacity for high-resolution data collecting, UAVs are an excellent choice for efficiently covering the tailings dam site. UAVs may capture high-quality photos when equipped with a high-resolution RGB camera, thermal sensors, or multispectral sensors. When these sensors are paired with image processing and machine learning algorithms, the result is a reliable estimate of the dam condition.

Jun 25, 2023

By M. Sanchez, I. Imris, G. Achurra

The Smelting and Converting El Teniente Process for copper concentrates as well as Slag Cleaning Furnace Technologies to treat slags coming out from the El Teniente Furnaces are widely applied today in Chile and around the world. Several industrial applications of this process have shown their capability to treat copper concentrates in a wide range of chemical and mineralogical compositions. Main operational parameters determining performance of the process are: oxygen enriched air flow rate, degree of oxygen enrichment, moisture content of the solid materials processed, molten material levels inside the vessel, frequency of molten materials tapping, bath temperature and copper losses in slags. In this work, the copper losses in the slags from El Teniente pyrometallurgical process are predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and slag industrial data. Results obtained show that the main part of copper losses in the slag from El Teniente Furnace are mechanically entrapped or floated unsettled droplets of the coexisting matte phase. by the contrary the very low copper losses in the slag from slag cleaning furnace are limited by the physico-chemical form.

Jan 1, 2004

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By M. Prasad, G. M. Rao, T. C. Rao, A. K. Majmudar

A two-step flotation scheme was employed to beneficiate a low-grade, cherty-calcareous rock phosphate ore from the Jhabua district, Madhya Pradesh, India. In the first stage, apatite and calcite ire floated together to remove silica, and, in the second stage, calcite is floated and apatite is depressed. The reagent scheme consists of sodium oleate, sodium silicate, orthophosphoric acid and sulfuric acid. The effect of reagent dosages on the efficiencies of separtition in each stage was studied systematically. A flowsheet was proposed for the processing of a low-grade phosphate ore containing 12.5% P2O5, 26.5% SiO2 and a CaO/P2O5 ratio of 2.64 (=32% calcite). The proposed flowsheet would produce a composite phosphate concentrate containing 27.2% P2O5, 6.37% SiO2 and a much reduced CaO/P205 ratio of 1.66. The total P2O5 recovery for the composite concentrate would be 73% .

Jan 1, 1996

By H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in southern Perú and the northern Chile coastal IOCG belt have emerged as two of the major exploration targets in the Central Andes in the last two decades. These Mesozoic Andean IOCG deposits formed in two mineralisation epochs, the Middle-Late Jurassic (170–150 Ma) and Early Cretaceous (130–110 Ma), with the major Cu-rich IOCG deposits located in the Early Cretaceous mineralisation belt. The early studies in some IOCG centres support a magmtic-hydrothermal model for both Cu-rich IOCG deposits and broadly contemporaneous Cu-poor ‘Kiruna-type’ magnetite deposits. However, recent evidence from field, geochronology, fluid inclusions and stable isotopes show that in the major Central Andean deposits (eg Raúl-Condestable, Mina Justa in southern Perú, La Candelaria-Punta del Cobre and Mantoverde in northern Chile), the incursion of evaporite-sourced basinal brines or sea water may be a prerequisite for economic Cu mineralisation. Moreover, the Cu-poor massive magnetite deposits could be interpreted as a product from iron oxide melt, with minimal intervention by non-magmatic fluids. Therefore, they could represent two contrasted deposit types and contain little genetic relationships. The different roles of magmatism during the Mesozoic are responsible for the variable mineralisation in the Central Andes, including IOCG, magnetite and ‘manto-type’ deposits. The ore modelling for both the Middle-Late Jurassic and Early Cretaceous metallogenic epochs in the Central Andes are reconstructed.CITATION:Chen, H, 2015. The Mesozoic iron oxide-copper-gold (IOCG) mineralisation in the Central Andes – a refined IOCG ore-forming model in the Palaeozoic Continental Margin, in Proceedings PACRIM 2015 Congress, pp 251–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Stacy Loizeaux

The Beirut Hilton Hotel, which was built in 1975, but never occupied, was imploded on Sunday, July 14, 2002 by Controlled Demolition, Inc. (CDI) of Phoenix, Maryland and their client, Optimal Engineering Consulting & Contracting, SARL, (OECC) of Antelias, Lebanon to make room for a new hotel. Twenty-seven years ago, just days before the grand opening, the Hilton Hotel became the site of fighting in Lebanon’s Civil War. Christian and Muslim militiamen fought room to room for control of the building and other nearby hotels. The Hilton, two other major hotels and other high-rise buildings were ravaged by the fighting. The building was one of the three major hotels badly damaged, but not rebuilt, in Lebanon. Located in the City Center, the Hilton stood out in a major redevelopment area which, in recent years, had erased the scars of the 15 year long Civil Wa r.

Jan 1, 2003

By Wilbur I. Duvall

In a review of so 40 papers on damage to residential structures resulting from blasting, only 3 were found that present data on the observed amplitude and frequency of the vibration levels produced by blasting together with an observed degree of damage to a residential structure. The data from these three reports have been analyzed statistically to determine if one of the quantities, displacement, velocity, or acceleration, is more reliable than the others for estimating the degree of damage to a residential structure. From this analysis the conclusion is drawn that a given degree of damage to a structure is most closely related to the magnitude of the particle velocity of the wave motion passing thru the earth at the structure location. On the average, only minor damage it observed for peak particle velocities of 5.4 inches per second, and major damage is observed for peak particle velocities of 7.6 inches per second. When the spread of the data is taken into consideration, the following statement can be made: Wave motions that have a peak particle velocity in excess of 2 inches per second have a fair probability of producing some damage to structures, whereas wave motions that have a peak velocity less than 2 inches per second have a very low probability of causing any damage. Therefore, the recommendation is made that vibration levels in the vicinity of residential structures should be maintained below a peat particle velocity of 2 inches per second. The above criterion for safe blasting is considered to hold over a wide variety of soil and rock conditions because the original data were obtained for a wide range of soil and rock conditions and on various types of residential structures. INTRODUCTION Ever since explosives were discovered and developed for mining purposes, there has existed the problem of what effects the air and ground vibrations resulting from blasting have on structures of various types. This problem is

Jan 1, 1962

By K. Barr, F. Grenier, J. Hettinger

"To reach the Hemlo Gold Inc. objective of becoming the lowest cost, safest Canadian gold producer while causing no environmental damage, management embarked from its inception on a strategy to build an organization which would foster employee involvement wherever possible. This paper describes the organizational structure and how various innovative concepts have been implemented.BACKGROUNDThe Golden Giant Mine in the Hemlo area of North Western Ontario is owned by Hemlo Gold Mines Inc. 50.1% is controlled by Noranda. The mine commenced operations in March 1985 at a modest production rate. After it reaches full production by the end of 1988, with completion of underground development work, the mine is expected to operate at 3000 t/d and produce in excess of 300,000 ounces of gold per annum. This makes it one of the three largest producing gold mines in North America.Two other companies, Lac Minerals and Teck-Corona, operate mines on either side of the Golden Giant Mine. Noranda Geco Division is located 55 kilometers to the north at Manitouwadge. The majority of Hemlo Gold's 270 employees live in Manitouwadge where a mix of accommodation was constructed and made available for purchase by employees. Bus transportation is provided to and from the workplace with modern coaches. The housing and transportation policies were implemented prior to start-up and designed to help attract and maintain good employees.As shown in Figure 1, the operation is divided into five operating and support departments with each reflecting a high degree of departmental control and responsibility. For example, the mill department is responsible for all aspects directly relating to the milling complex including safety, operation, mechanical maintenance, assaying, instrumentation, and environmental control. Similarly, the mine department is responsible for all phases of operation, mine engineering, geology, and maintenance of underground mobile equipment. The plant department is responsible for maintenance of hoisting plants and conveyances, underground stationary equipment, all site electrical services, surface buildings, housing and yard maintenance. Efforts are made at every level of the organization, from departmental organization to individual job assignments, to ensure responsibilities are clear and that they encompass complete functions."

Jan 1, 1988

By Larry A. Enloe

The 16-to-1 milling operation is Sunshine Mining Company's first new silver and gold producing facility. The 16-to-1 underground mine and mill are located approximately 64 km (40 miles) southwest of Tonopah, Nevada. Ore re- serves in the epithermal vein deposit are estimated at 0.91 Mt (one million st) of ore, at an average silver grade of 206 to 240 g/t (6 to 7 oz/st) and an average gold grade of 1.2 g/t (0.035 oz/st). The underground mine uses a large diameter blasthole stoping system of mining using highly mechanized rubber-tired equipment. The mill uses conventional cyanide leaching with countercurrent decantation and Merrill-Crowe precipitation. The mill start-up was in February 1982 resulting in the first pour of dore' in March 1982. The mill's present annual production is approximately 31.1 t (1.0 million oz) of silver and 264 kg (8500 oz) of gold.

Jan 1, 1984

By Amalia Giannakou

This paper utilises 3-D finite-element modeling to study the static and dynamic lateral harmonic response of inclined piles, in a homogenous and a non-homogenous soil, modeled as a linear hysteretic medium. The results of a comprehensive parameter study are presented in the form of dimensionless plots of: (a) static and dynamic swaying and rocking stiffnesses and damping ratios, and (b) distribution of internal forces (bending moment, shear and axial force) with depth. These plots can be readily utilised in practical applications and they offer insight on the role of the inclination in the response of flexible piles.

Jan 1, 2006

By R. A. Franks, J. C. Edwards, L. Yuan

To determine the critical air velocity for preventing smoke rollback, diesel-fuel fire experiments were conducted in the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Research Laboratory’s Safety Research Coal Mine. Such information is necessary for preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 to 300 kW depending on the fuel tray area. Airflow in the 2-m- (6.6-ft-) high, 2.9-m- (9.5-ft-) wide coal mine entry was regulated during the course of each experiment. The airflow was measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor and was recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light-obscuration monitors, ionization smoke sensors and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics fire dynamics simulator.