Search Documents

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

By Enrique Fernandez

M-30, Madrid’s inner ring, covers 42 sq km of the city centre where one million people reside. It was constructed in several phases during the sixties and the eighties. The design criteria applied to those phases were different and were not always homogeneous with urban roads with lighting regulation as well as speedways. These areas had a heavy concentration of access and exits and there had been made many changes on the number of traffic lanes which has caused heavy traffic congestions and high accident rates. The environmental impact and noise pollution in residential areas are also consequences of M-30. The Madrid Major took a decision at the beginning of the present legislation, based on socio economic and environmental evaluation; rebuild the M-30 with the following sustainable mobility principles: Underground transfer of a considerable portion of the main ring and some of its links replacing some parts of the surface with new green areas in order to reduce the environmental impact. Increase the traffic capacity, improving the traffic continuity and fluidity and eliminating the lighting regulation areas, which is one of the main congestion problems currently. Increase the traffic safety with clear signalling information panels and avoiding difficult maneuvering. Redesign the links with the high capacity radial highways and other connecting lanes of the city. The project is worth 3.7 billion Euros. In 2007, when the construction is completed, it is expected will save 14 million of journey hours that represent 4.5 million Euros saved in fuel consumption per annum, There will be a very significant reduction of 35,000 tons of CO2 in terms of pollution and 400 less car accidents. Those values will increase even more in the following years. The areas beside Manzanares River, running parallel to the M-30 on the western side of Madrid, will be highly enhanced. Better water quality and the recovering of the green areas existing in old times will also return for the citizen’s enjoyment. TUNNEL CROSS SECTION OF CALLE 30 SOUTH BY PASS One of the major challenges of the new Calle 30 is actually not only the related to the main road but also to the link with the A-3, with highway to Valencia. This link is currently the most congested area and has one of the highest traffic densities of Spanish roads, with more than 250,000 vehicles/day. The remodelling of this area is the principle objective of the South by-pass. The tunnel is the only answer for this by-pass as the road alignment will go among buildings. A twin tube design, one for each direction, with three lanes allowing the circulation of both, light cars and heavy trucks, is the solution that has been

Jan 1, 2007

This report presents the results of a study for the Bureau of Mines to compare loan terms for non-fuel mineral projects in developing countries, from various International Financial Institutions (IFIs), and from private sector commercial sources. The study compares IFI and commercial loan terms for seven mineral projects in developing countries. The International Financial Institutions represented are: ? International Bank for Reconstruction and Development (World Bank) ? International Finance Corporation (IFC) ? Inter-American Development Bank (IDB) ? Asian Development Bank (ADB) ? International Monetary Fund (IMF) In addition, the costs of financing for these mineral projects were compared with the costs of long-term debt to the five largest U.S. mineral producers.

Jan 1, 1986

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100 per cent recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after 12 years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By L. J. Prosser, A. T. Iannacchione

Unfortunately from 1991 through 1995, 44 miners were fatally injured in the stone industry. Of these 12 occurred at underground mines from a total work force of less than 2,000 miners. Nine of these 12 miners were fatally injured in falls of roof or rib. A safer environment for the miners can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground control strategies. Roof and rib conditions in the underground stone industry were observed and assessed at 33 mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania, and West Virginia [(Figure 1)]. Hazard assessment indicated that those ground failures occurring under moderate to substantial overburden (> 30 m [l00 ft]) were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine layout decisions tremendously influence ground stability.

Feb 24, 1997

By M. J. Farrell

Mining is a significant emitter of greenhouse gases and is the focus of increasing attention from green groups and regulators. Miners need to know their own carbon emissions and how they compare with the rest of the industry. Miners and mining companies need to know where they fit in the emissions curve. Who is in the bottom quartile? This article updates data from minecost.com which detail the specific carbon dioxide emissions for over 200 mines producing 90% or more of western world copper, zinc, lead and nickel in 2009. This data shows the potential impact on mine economics of proposed carbon taxation regimes and emissions trading schemes proposed at COP 15 in Copenhagen during December.

Jan 1, 2010

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Rita D. Sylvester

"This compilation lists and summarizes publications by Bureau authors published in the regular Bureau of Mines series, in scientific, technical, or trade journals, or in other media; those available from the Bureau of Mines are indicated. Patents issued to Bureau personnel are also listed, and instructions are given on how to apply for permission to use them. One of the outstanding features of this Special Publication is an exhausive subject and author index. IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and present their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries, The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminar's; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January 1, 1970, to December 31, 1974. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960;2 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960;3 and the 5-year lists of Bureau publications and articles from January I, 1960, to December 31, 1964,4 and from January I, 1965, to December 31, 1969.5 It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1970, to December 31, 1973."

Jan 1, 1975

By K. E. Stanfield

[Asphalt and road oil are the principal products manufactured from Wyoming ?clack oils? which, because of their high asphalt an high sulfur content, are difficult and costly to refine into high-grade motor fuels, burning oils, and lubricants by pre sent methods. Accordingly, the remand for these asphaltic residuums for the construction of roads and other uses is a controlling- factor in the quantity of crude oil produced. The increasing utilization of special asphalts as inexpensive bonding, insulating, and waterproofing materials indicates the desirability of obtaining information on the yield and properties, of asphalts from Wyoming black oil to promote a wider and more stable caret for these asphaltic materials.]

Jan 1, 1941

By C Li, D O’Dea, R Moreno-Atanasio, T Honeyands

The behaviour of iron ore granules in the feeding process of sintering is significantly influenced by the material properties of the granulated mix. Therefore, the measurement of key material properties of the iron ore granulated mix is indispensable prior to the simulation of the sintering process based on the discrete element method (DEM). In this paper, three key property parameters of the iron ore granulated mix, apparent density, elastic modulus and rolling friction coefficient, were measured in laboratory-scale experiments. For different sintering processes, the moisture content of the granulated mix normally varies according to the specific requirements for granule size distribution and operating conditions. Therefore, understanding the effect of moisture content on the property parameters of iron ore granules is very helpful in accurately determining the property parameters for DEM simulation work. In this paper, six groups of iron ore granule samples with six levels of moisture contents were prepared through granulation and the trends in apparent density, elastic modulus and rolling friction coefficient with the increase of moisture content were plotted and analysed based on the measurement results. The results show that as moisture increases from 6.9 per cent to 9.1 per cent, the apparent density decreases from about 3000 to 2800 kg/m3. With moisture increasing within the same range, the elastic modulus first decreases from over 200 MPa to below 100 MPa and then reaches a relative constant value of about 40 MPa at higher moisture contents. Rolling friction coefficients are measured using two methods with both indicating a similar trend, with the rolling friction coefficient first decreasing and then rising as moisture increases from 6.9 per cent to 9.1 per cent. The relationship between µr and µ’r is assumed to be similar to that between static and dynamic friction coefficients.CITATION:Li, C, Moreno-Atanasio, R, O’Dea, D and Honeyands, T, 2017. Variation in property parameters of iron ore granulated mix with moisture content, in Proceedings Iron Ore 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By Mark E. Hammele

A number of new thoughts have recently emerged concerning the role of air decks, stemming, gas confinement and gross motion in specific blasting environments and applications. Field research in full-scale production environments is based on the theoret ical work f i rst proposed at the Universi ty of Maryland’s Fracture Mechanics Laboratory.

Jan 1, 1989

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck&apos;s bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company&apos;s Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999