Search Documents

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By Adam Powell, Matthew Earlam

INFINIUM, Inc. is scaling up a new molten salt electrolysis process for producing rare earth metals. Instead of conventional carbon anodes, this process uses Pure Oxygen Anodes™ which employ a stabilized zirconia solid electrolyte between the molten salt and anode. This eliminates two problems with today's rare earth metal production technology. First, it eliminates carbon anodes and contamination of the product by carbon and its impurities, enabling 10-100 times larger batch size than current practice, and lower labor costs. Second, it eliminates emissions of perfluorocarbons (PFC) such as CF4 and C2F6, which are very problematic greenhouse gases with 6000+ times the global warming potential of CO2. The zirconia also enables a sealed vessel with no LiF emissions, creates a reducing environment enabling use of low-cost welded steel vessels, and either produces a high-purity oxygen by-product or can use natural gas to reduce the necessary electrical energy with no HF production. This paper will describe the technology and its current status for rare earth metal production.

Jan 1, 2014

By George H. Willis

In the second half of the nineteenth century, bimetallism progressively replaced by gold standard. After World War I and 1931-33 depression, gold mainly reserved for official international transactions and internal use restricted. Changes since 1971 have shrunk official international use of gold. International payments deficits and surpluses now financed by private and official credit, rarely by gold. Historical review covers evolution of: (1) internal and external private use, (2) internal official use, (3) external official use, (4) role in IMF and (5) use as unit of account.

Jan 1, 1978

By D J. Holden

Prospectivity, the relative value of gold, investor confidence, general economic stability and legislation driven by public attitudes are seen as the major influences on the gold mining industry in New Zealand. Since the 1860s the gold mining industry in New Zealand has been subject to the complex interaction of these influences resulting in three successive boom and bust periods. The booms are related to periods of greatest potential economic growth. The busts are more strongly related to downturns in the economy and falling gold price. The influences may be expressed as trends over time. The role of gold has changed from being a currency base to that of a traded commodity. This change has caused price instability and rapid fluctuations in its value. Increased competing land uses, shifting public attitudes and legislative changes have added to the instability of the industry. Reaction against change is to be expected from the companies until new legislation is seen to be functioning efficiently. Other trends show that there has been a tendency towards reduced exploration and consolidation of active gold mining projects. The future consequences of this are likely to be felt both regionally and nationally as there will be no new discoveries to fill production voids which will develop as currently producing mines close. The review of New Zealand's resource use statutes is nearly complete. A period of legislative stability can now be expected. There are some positive signs that consents will be obtained much more quickly than under previous legislation, particularly by those companies which develop the skills to work with the system. The new regime is about consideration of impacts rather than specific activities. This, together with excellent prospectivity, bodes well for the identification of mineral resources in New Zealand.

Jan 1, 1992

By W. F. Hazen

This paper describing the mining practices at a 100 per cent mechanized mine working the Pittsburgh or No. 8 coal bed in eastern Ohio is one of a series being prepared by the U. S. Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The purpose of assembling this data is to place before those interested in the mining industry the methods employed and the cost data on the items involved in the winning of the coal and its removal to the railroad car at the tipple. Mining costs are governed by the mining method used, which is selected for its adaptability to local natural physical conditions such as the nature and thickness of the coal, its dip, the character of the roof and floor, and the thickness of the overlying strata.

Jan 1, 1929

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By Michael J. Brown

It is often necessary to undertake some form of pile testing to verify design calculations. Historically this has been limited to static and dynamic tests. Newer rapid testing methods such as Statnamic are seeing more frequent use. This form of testing can be advantageous due to short set up time and test duration. Although the methodology suffers from a lack of formalised guidance and may prove difficult to analyse in certain soil conditions. This paper investigates the suitability of Statnamic testing and analysis for a range of soil and pile types as well as different installation methods through a number of case studies undertaken in the UK. Recommendations are made on test specification and analysis.

Jan 1, 2006

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By Christian J. Sorensen, Christopher Armstrong, Andrew Matejunas

A team consisting of junior and senior mechanical engineering students at New Mexico Tech worked on the design of an explosively loaded vessel, with a maximum load of 15 grams (0.53 oz) TNT equivalent explosive. The main challenge presented was to meet the stringent sample positioning specification of 3 microns in two Degrees Of Freedom (DOF) and one degree of rotation in a third DOF. This is to accommodate precise sample placement in a tight x-ray beam, and to bring areas such as explosives/metal interfaces into magnified field-of-view photography. This presentation describes the process and design decisions to arrive at the final product presented to LANL in December 2014. Our engineering analysis techniques will be reviewed, including use of American Society of Mechanical Engineers (ASME) Boiling & Pressure Vessel Code (BPVC) Code Case for Impulse Loaded Pressure Vessels (ASME BPVC Code Case 2564-3). Also discussed will be integration of Hydrocode computer models with Finite Element Method analysis.

Jan 1, 2015

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By P. M. Ambrose, A. C. FtELDNER

This , the twelfth annual report of research and technologic work conducted by the Bureau of Mines on coal and coal products , summarizes the research and tests conducted frah July 1, 1946, to July 1, 1947. The organic act of Congress establishing the Bureau of Mines authorized tech- nologic investigations of all phases of mining, preparation, treatment, and utilization. These investigations cover eight main fields of activ-. projects varies from time to time. The on ity. The emphase-half of the coal reservos of the world. United States These reserves are not always of the quality desired or in the place where they could best be used. It is necessary to continue research in order that increased output, greater recovery, and better quality can be main- tained under safe mining conditions. Coal comprises 98 percent of the known fuel reserves of the United States and ad eventually must take over much of the requirements now supplied by petroleum and natural gas.. The purpose of this report is to bring to the reader a resume of the work of the fiscal year. The material presented herein is based largely upon publications. In a few instances the results of research that would not otherwise be available in the immediate future are presented. For details concerning the research, it is suggested that the readers consult the publications given in the footnote references." Collected references to all Bureau of Mines publications on coal are published in a series of bibliographies. Technical Paper 576 covers 1910 to 1935; Technical Paper 639 covers 1935 to 1940; and Technical Paper 698, issued in 1947; covers' 1940 to 1945.

Jan 1, 1948

By Felix du Breuil

Contract H0177044 included three objectives; (1) consolidate, maintain, and distribute information on STE approved lighting systems; (2) develop and present one-day seminars on underground mine lighting; (3) determine direct labor and hardware costs associated with the installation of mine illumination systems. All objectives were completed with results as follows: Task I - A file containing 1350 Statements of Test and Evaluation (STE) for all types of underground equipment was developed and publicized throughout the coal fields, A total of 40 requests for STE information was received and processed. Task II and III - A series of 50 seminars was scheduled and presented to 942 attendees throughout the coal fields. The seminars were well received and attendees indicated the information presented would be helpful in bringing their equipment into compliance. Holding a series of seminars in the coal fields, instead of a few in population centers, was favored by attendees. Task IV - Installation cost data obtained on 415 lighting systems indicate that the factors which most affect installation costs are higher hardware cost for DC powered systems and slightly higher manpower requirements for systems installed underground. Based on these data, the total cost to industry of retrofitting existing underground equipment could range up to $50 million.

Jan 1, 1979

By L. Garycki, P. Poks, R. Urbaniak, T. Gabka

In 2016 at Głogów Copper Smelter KGHM Polska Miedź S.A., after shutting down the shaft furnaces new FSF was launched. Currently, it is the only smelter with two direct to blister flash smelting furnaces in operation. The main difference between the vessels are the dimensions and production capacity. The new furnace design output is about 30% higher compared to the old flash smelting furnace working for 40 years. The paper presents a comparison of both FSFs operation, differences in technology and the way to optimize the process to maximize efficiency. INTRODUCTION KGHM Polska Miedź S.A. is the only company in Poland (eastern part of Europe) that extracts and processes copper ores. It is located in the south west of Poland and this region is called the "Copper Basin”. KGHM PM S.A. consists of three underground mines: Lubin, Polkowice-Sieroszowice, Rudna, concentrator plants, a tailings pond plant, three copper plants: Legnica, Głogów and Cedynia wire rod plant in Orsk. The publication relates to the operation of the furnaces in Głogów (the plant in Głogów consists of Głogów 1 and Głogów 2 which form integrated smelting and refining facilities). In 2016, after closure of the shaft furnaces technologies in the Głogów 1, a new FSF commenced operation. The simplified process flow sheets are given in Figure 1 and 2. Technological schemes are similar, but due to the differences in them, they will be discussed separately. Głogów 1 Enriched ores are discharged and directed to the feed preparation plant. Delivered concentrates are built up on the three bedding aisles in appropriate proportions. The concentrates are distributed in even layers in one of the three aisles. Aisle emptying is done with a blending machine which cuts across the concentrate layers and collects thus blended material, sending it via belt conveyors to a storage bin. From the cross- blending machine and conveyor assembly, the mixture of concentrates is directed to drying in the steam dryer. Part of the charge is directed to the FSF and part to the roaster for carbon elimination. Known in the world roasters are used to eliminate sulfur compounds or arsenic. In the case of KGHM deposits, the aim of the process is to reduce the energy value of the feed by eliminating carbon and converting sulfur from sulfide to sulfate. Changing the nature of exothermic to endothermic material is crucial in the case of furnace operation with design performance. Roaster is a separate furnace with an innovative character.

Jan 1, 2019

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

Cessation of mining on the Bendigo goldfield makes it evident that, as the older generation fades away, knowledge of the famous Bendigo saddle reefs will be limited in the future by their written records. It is important therefore that the summarised account by D. E. Thomas (1953) in the Geology of Australian Ore Deposits should not be misleading. Fig. 6 in this article is stated to portray a cross section and longitudinal section through a series of gold shoots in the Garden Gully 300 ft. reef. The gold shoot along the capof the saddle reef is represented as extending down the east leg in a series of prongs, with the tips of the prongs about 50 ft. apart. It is the purpose of this note to indicate that this illustration can be suspected to be a diagram of the old stopes instead of a diagram of the distribution of gold in the quartz.The original sketches of Figs. 6 and 7 in Thomas' account were extracted, I believe, from the field note books of H. S. Whitelaw, years after his death in the late twenties. Whitelaw was stationed in the Bendigo office of the Geological Survey of Victoria, carrying out geological surveys of the Bendigo mines. He was there for many years before the Gold Research committee started its investigations in 1916 and he was acutely aware of the problem attached to the distribution of gold in the reefs. He had felt concern that manyauriferous reefs were being mined without adequate study and record and he decided, as he expressed it to me, to pick up what he could as he went along. There can be little doubt that the diagrams of Figs. 6 and 7 are products of this resolve.Opportunities to investigate gold occurrences at Bendigo were limited before 1916 because the field was operated by Manuscript received at The Institute 18th November, 1960.

Jan 1, 1961

By Christoph Miller

About 80 years ago the mining industry saw an advertisement of a machine manufacturer: ?One man ? one machine?, meaning the productivity gain by using a pneumatic rock drill instead of manual tools. Mechanization in mining had started. In the 1950's and 1960's when mechanization progressed the word could be transformed into the meaning of ?one man ? one drill rig?. During the 80's automatic functions were added to the machines. Automation started. In the 90's, the first autonomous machines were seen, transforming the advertisement from the 1920's into ?one man ? multiple machines? operated from a remote control room. Soon, the productivity gain achieved by pure automation will also be flating out meaning that the margin cost of further productivity gain will be inefficiently high. What next? In mining operations there is still a high potential of unused productivity lost by ?trivial? things like organization, logistics and operational management. Changing the focus from mechanization and automation towards optimizing the overall mining process will unleash another big potential for cost cuttings and for enhancing efficiency of production. Optimizing an overall process is a task of much higher total complexity compared to an isolated machine automation focus. And a successful process integration requires the collaboration of machine vendors, infrastructure suppliers, IT services and the mine itself. It requires a number of of important preconditions to be fulfilled: ? Integrated IT systems with seamless interfaces between all components and peripherals involved ? Real time information access in all locations ? Real time overview of all operational aspects A crucial aspect for all of these issues is a seamless communication both above and also under ground and IT interfaces which are easy and price efficient to implement. This paper highlights ways to achieve productivity gains by process optimization. It also discusses needs for industry wide activities in order to enable cost efficient performance of mine process optimization projects.

Oct 1, 2009

By S. Sakurai

We discuss the mechanical characteristics of underground structures that are subjected to vertical oscillations. Under such circumstances - expected when an earthquake rupture occurs very close to highly developed urban areas - the conventional seismic analysis, which mainly considers horizontal shear oscillations, may not be fully valid. Our analysis, based on the elastic wave theory, shows the effects of vertical disturbances and the generation mechanism of the unique damage patterns observed on the occasion of the 1995 Hyogo-ken Nanbu (Kobe) Earthquake. Wir diskutieren über die mechanischen Eigenschaften der unterirdischen Strukturen, die sich vertikalen Schwingungen aussetzen. Unter solchen Umständen - erwartet, wann ein Erdbebenabbruch sehr nah an hochentwickelten städtischen Bereichen geschieht - kann die herkömmliche seismische Analyse, die sich hauptsächlich horizontale Schubbewegungen überlegt, möglicherweise nicht völlig gültig sein. Unsere Analyse, basiert auf der elastischen Wellentheorie, zeigt die Effekte der vertikalen Bewegungen und den Erzeugungsmechanismus der einzigartigen Beschädigungsmuster, die anläßlich des 1995 Kobe Erdbebens beobachtet wurden. Nous discutons les caractéristiques mécaniques des structures souterraines qui s’exposent aux oscillations verticales. Dans ces conditions - s’attendent quand une rupture de tremblement de terre se produit tout près des secteurs urbains fortement développés - l’analyse séismique conventionnelle, qui considère principalement des oscillations horizontales de cisaillement, peut ne pas être entièrement efficace. Notre analyse, qui est basée sur la théorie des vagues élastiques, montre les effets des mouvements verticaux et le mécanisme de génération des modèles uniques de dommages, que nous avons observés à l’occasion du tremblement de terre 1995 de Kobe.

Jan 1, 2003

By A. Rejeb

ABSTRACT: This paper contributes to the study of underground structures in argillaceous media, especially Tournemire argillites (Aveyron, France). The basic results obtained over six years in two experimental drifts at the Tournemire site are presented. In situ measurements cover drift wall temperature, humidity and convergence. Delayed convergence represents around 50-65% of the total measured convergence. Analysis of the measurements has shown that delayed convergence is explained by the viscoplastic behaviour of the argillaceous formations. Lemaitre’s rheological model has been extended to the orthotropic case, as Tournemire argillite is naturally anisotropic. The triaxial creep test results on samples at different orientations enabled the parameters of the Tournemire argillite to be identified in terms of orthotropic viscoplastic law. A plane deformation model, using this rheological law and the initial stress field in the site, was developed to interpret the convergence measurements in the drifts. The computed results match the measurements well, especially during the excavation phase. KEY WORDS: Argillite, convergence, time-dependent behaviour, creep, viscoplasticity, modelling. ZUSAMMENFASSUNG: Der vorliegende Artikel ist ein Beitrag zur Untersuchung der unterirdischen Strukturen tonhaltiger Milieus, insbesondere der Tongesteine von Tournemire (Aveyron, Frankreich). Die wichtigsten Ergebnisse, die in zwei Forschungsstrecken am Standort Tournemine über einen Beobachtungszeitraum von sechs Jahren zusammengetragen wurden, werden hier vorgestellt. Gemessen wurden in situ Temperatur, Feuchtigkeit und Streckenkonvergenz. Von der insgesamt gemessenen Konvergenz sind etwa 50 bis 65 % auf zeitlich verzögerte Konvergenz zurückzuführen. Die Auswertung aller Messungen hat ergeben, dass die zeitverzögerte Konvergenz mit dem viskos-plastischen Verhalten des Tonsteinmassivs zu erklären ist. Aufgrund der naturgemäßen Anisotropie des Tongesteins von Tournemine wurde das rheologische Modell von Lemaitre auf den orthotropen Fall ausgedehnt. Triaxiale Kriechversuche bei jeweils unterschiedlicher Ausrichtung dienten der Ermittlung der einzelnen Parameter des orthotropen, viskos-plastischen Gesetzes. Zur Auswertung der Konvergenzmessungen innerhalb der beiden Strecken wurde unter Beachtung dieses rheologischen Modells sowie des ursprünglichen Spannungszustands vor Ort ein flächiges Deformationsmodell entwickelt. Die Rechenergebnisse zeigen eine gute Übereinstimmung mit den Messungen, insbesondere während der Vortriebsphase. SCHLÜSSELWÖRTER: Tongestein, Konvergenz, zeitlich verzögertes Verhalten, Kriechen, Viskoplastizität, Modellbildung. RESUME : Cet article est une contribution à l’étude des structures souterraines dans les milieux argileux, notamment les argilites de Tournemire (Aveyron, France). Les principaux résultats obtenus pendant six années, dans deux galeries d’expérimentation au site de Tournemire, sont présentés. Ces mesures portent sur la température, l’humidité et la convergence des parements des galeries. La convergence différée représente environ 50 à 65% de la convergence totale mesurée. L’analyse de l’ensemble des mesures a montré que la convergence différée est interprétée par le comportement viscoplastique du massif argileux. Etant donné que l’argilite de Tournemire est naturellement anisotrope, le modèle rhéologique de Lemaitre a été étendu au cas orthotrope. Les résultats des essais de fluage triaxial, sur des échantillons à différentes orientations, ont permis de déterminer les paramètres de la loi viscoplastique orthotrope. Un modèle en déformation plane, utilisant cette loi rhéologique et l’état de contrainte initiale dans le site, a été développé en vue d’interpréter les mesures de convergence dans les galeries. Les résultats des calculs sont en bon accord avec les mesures et plus particulièrement durant la phase de creusement. MOTS-CLEFS : argilite, convergence, comportement différé, fluage, viscoplasticité, modélisation.

Jan 1, 2003