Search Documents

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981

By John P. Powell

The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing new oil fields are factors that emphasize the importance of increasing the recovery of oil from known petroleum reserves. Water flooding is a valuable conservation measure, not only preventing premature abandonment of stripper leases but also reviving interest in many areas previously abandoned. The use of water flooding as a means for recovering additional oil from partly depleted oil-bearing formations was first tried in Oklahoma in 1931. Early water-flooding operations were confined to the area of shallow Bartlesville-sand formations in Nowata and Rogers Counties, where many of the projects were outstandingly successful. The results of these operations stimulated activities in other pools in Oklahoma, and by the end of 1949 water flooding had been tried in 25 of the 49 oil-producing counties in the State (fig. 1). Approximately 33 million barrels of oil, or 1,806 barrels per acre, had been recovered by December 31, 1949, from 18,221 productive acres included in the 162 active and abandoned projects in Oklahoma by injection of approximately 449 million barrels of water.

Jan 1, 1952

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By A Giblett, R Dunne, D Appelhans

There are a number of hurdles that must be negotiated in order to design an effective gold ore treatment facility such that the expectations forming the basis of project economics are valid and can be achieved in practice. Selecting samples based on geometallurgical context, performing and interpreting testwork relevant to the selected process flowsheet are essential considerations towards achieving this aim. This paper discusses recent experiences in process development for free milling gold ores giving consideration to frequently encountered challenges of this nature.CITATION:Giblett, A, Appelhans, D and Dunne, R, 2013. Considerations for effective gold process development, in Proceedings MetPlant 2013 , pp 445-454 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By B. Ceki, A. Mabentsela

The BCL furnace is scheduled to restart operations after being placed on care and maintenance in 2016 due to depressed nickel prices. The decision to start operations after such a stoppage ought to be led by a techno-economic evaluation of process options to make operations more resilient. For BCL, the decision lies between using the existing flash-smelting furnace (FSF) or a top-submerged lance (TSL) furnace. Available studies show that the FSF combined with other converting technologies is cheaper to operate; however, such studies are based on flowsheet simulation results of single copper concentrates and therefore do not provide a full scope of practical capabilities based on smelter operator skills. Using a t-test on normalized prior operational data from three Cu FSF and two Cu TSL, it was found that the only statistical differences between the operating costs of the FSF and TSL technologies are in the coal use for heating the feed blow and number of rebuilds: the FSF consumes coal to heat the feed blow and the TSL requires 2.4 rebuilds during a course of a single FSF campaign. A summative operating cost comparison over the existing BCL FSF 11-year life shows that BCL can decrease operational costs by some BWP 55.5 million if the operation were to change to the newer TSL technology. The savings derive from reduced coal use, which is normally associated with heating the blow when using the FSF. Despite the TSL carrying added costs of 2.4 rebuilds during a life time of one FSF furnace campaign, the cost associated with the TSL rebuilds of approximately BWP 1.3 million is minimal compared with the overall operational expenditure decrease that BCL will incur on using the TSL technology. In terms of the technology, BCL can have higher Ni–Cu recoveries at lower operational costs by elimination of Ni–Cu losses and eliminating the slag-cleaning furnace by converting to a TSL furnace.

Jul 10, 2024

The lignite deposits of the United States represent a huge potential source of fuel for power generation. It has been estimated that lignite constitutes about 24 percent of the remaining National reserves of solid fuel on a tonnage basis and about 15 percent of the reserves on a B.t.u. basis. (See sec. 3, part 1.) The major portion of these reserves is in North Dakota. Lignite has been used locally for domestic heating since the first settlers burned it at forts and fur-trading posts as early as 1855. Some of the first studies of the use of lignite in steam boilers were conducted by the Federal Bureau of Mines from 1910 to 1920 (15, 19) 1/ However, the commercial utilization of lignite as fuel for producing power developed slowly. Not until about 1925 was any really successful lignite industrial fuel-blaming equipment developed. Since then the commercial use of lignite as a fuel for producing power has been increasing steadily.

Jan 1, 1954

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

"D bed, Ky., coaL, washing characteristics RII 5140coking coal, reserves, estimate RI 5037Pa., coal, washing characteristics RI 4834, 4941D bed mine, Ky., coal, washig characteristics"

Jan 1, 1960

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

By Joshua A. Bennett

"Lawsuits where owners allege their property has been damaged by nearby blasting routinely costblasting companies, explosives engineers, and others in the field both time and money. When ownersfeel the vibration of a blast, they immediately begin to look for damage and usually find cracking thatwas, in fact, present prior to the blasting occurring. When those owners begin to talk to their neighbors and legal counsel, blasting entities suddenly have multiple lawsuits being filed as a result of the same blast."

Jan 1, 2016

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006