Search Documents

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

By Jose Luis Sosa, Marco Surichaqui, Ramirez Marcelino

El proyecto permite obtener resultados de operación que no siempre son los esperados en cuanto a calidad y recuperación, aquí es donde destaca el programa; tiene una data que PRONOSTICA estos resultados, con el control de parámetros, corrigiendo estos resultados al valor óptimo esperado, haciendo que su empleo permita obtener en “tiempo real” excelentes resultados en cuanto a calidad y recuperación del licor lixiviado y se refleja en costos.

Sep 1, 2017

By M. Sagheer

An 8.5-km (5-mile) conveyor has gone into operation in western Turkey to eco¬nomically transport crushed lignite from the mine area to a power plant. This conveyor has replaced trucks as the principal mode of transporting the lignite. One principal element of Turkish govern¬ment policy is the country's commitment to increase electricity supplies for mining and other industries. Lignite is an important source of electric power supply in Turkey. Production was about 48 Mt (53 million st) in 1987, amounting to more than 20% of the total power supply in Turkey. In the western Anatolia supply network, it plays a major role for power generation. Deposits are located in the Soma region of western Turkey. The lignite is of low quality, deposits are scattered, and the terrain is dif¬ficult and hilly. These conditions demand an economical and technically feasible method of transporting the raw material from mining areas to the central thermal power plant. The Soma power plant is located about 120 km (75 miles) northeast of Izmir, near the coast of Aegean Sea. An overland conveyor of a unique design has gone into commercial operation at the Soma power plant facilities of the Turkish state electricity organization, Türkiye El¬ektrik Kurumu (TEK). The conveyor re¬places truck transport to ensure economical use of the lignite deposits. Computer-aided design (CAD) added more precision, qual¬ity, and flexibility of engineering in design activities. It also helped quick realization of the project that was executed in cooperation with the German company Krupp Industri¬etechnik and the Turkish firm Gama Endüstri AS. Unique features The conveyor includes several major features rarely combined in a single flight: Overland long distance conveyor. • Horizontal curves. -Steep vertical concave and convex curves to match the difficult terrain. Down-hill conveying. Frequency converter drives with vari¬ able belt speed. Generating operation mode to backfeed the energy to the network. Layout The 8.5 km (5 mile) long conveyor takes the -200 mm (-8 in.) lignite from the primary crushing plant located near the mine to the central, final crushing plant located in the stockyard area near the power station. The drive and belt tensioning assemblies are situated near the tail end of the flight. The high voltage switchgear is housed in a room in the primary crushing plant build¬ing upstream from the conveyor flight. The frequency converters are installed in the low voltage switchgear room located below the control room within the primary crushing plant building. Conveyor design The conveyor includes two 4 km (13,120 ft) radius horizontal curves, one left-hand and the other right-hand. The minimum radii

Jan 1, 1989

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By Michael W. Neill, O&apos

The engineering profession generally does not accept vibro-driven piles as bearing piles unless their capacities can be verified by restriking with an impact hammer, which significantly reduces the economic benefits of vibratory driving. In part, the concern for capacity development in piles driven by vibration arises out of observations that vibro-driven piles do not develop capacities equivalent to those driven by impact (e. g., Mosher, 1987). Nonetheless, if capacities are predictable, vibratory installation may be more cost effective than installation by impact, due to savings in time of installation, even if capacities are lower than those of impact-driven piles. Throughout the past few decades, a number of attempts have been made to develop capacity prediction methods for vibro-driven piles, mostly along the same lines as methods for impact-driven piles. That is, (1) totally empirical formulae, (2) power balance / power transfer formulae, and (3) "time domain-nonlinear" (TDN) computational procedures such as the wave equation. Some of the formulae have been based partly on field experience, but the majority have been developed from simple theoretical models with parameters evaluated from laboratory studies. Neither these formulae nor the TDN solutions have been systematically checked (or modified) by recording appropriate field data over a variety of site

Jan 1, 1989

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 25 underground coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, "A Guide for the Evaluation of Human Exposure to Whole Body vibration." The comparison showed that about 30% to 40" of all underground coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only 10 to 15% would be expected to experience vibration exceeding the exposure limit. The primary sources of the exposure are shuttle cars and possibly scoop trams. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By G. I. Gritsko

In this paper we consider the elements of a distributed information geomechanic monitoring system which is used in computerized mine planning and mining operations control. The automated system is a technical means of geomechanic monitoring, as a complex system of regulated observations, estimation and prediction of geomechanic state of rock mass and workings during underground mining of coal deposits. Geomechanic monitoring at coal mines and the automated system execute data collection, analysis and calculations of geomechanic situation in the panel during planning, development and carrying-out of mining operations for ensuring geotechnical stability of underground mining.

Jan 1, 1996

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

By J K. Wright

In recent years the production of steel from directly reduced iron ore pellets has expanded rapidly. However, continued growth will depend on an adequate supply of suitable raw materials for the various commercial gaseous and solid reductant processes now in operation. Although at present Australia does not produce pellets primarily for direct reduction, there is an increasing awareness of Australia's potential role as a supplier of high grade ores for export and/or domestic use. The properties and quality requirements of iron ore pellets made specifically for direct reduction (DR) are reviewed and the laboratory techniques and test methods used at the CSIRO Division of Process Technology for the evaluation of potential DR feedstocks are described. At the present time most of the evaluation tests for DR pellets are extensions of those designed for existing blast furnace (BF) burdens. In the case of some physical parameters such as cold compression strength, abrasion index and cold strength after reduction this extension is quite satisfactory. In the measurement of parameters such as reducibility, swelling and sticking tendency, however, it is necessary to develop meaningful standardized tests so that ores and pellets can be ranked for DR performance. To do this, data from the laboratory tests and from operating plants must be correlated.

Jan 1, 1980

By Terry P. Medhurst, Stuart A. MacGregor, Peter J. Hatherly

In addition to fractures and joints, compositional factors and bedding influence the strength of clastic sedimentary rocks. Rock mass rating schemes must therefore consider all of these factors. In this paper, a rating scheme for clastic sediments based on geophysical measurements is described. Geo-physical logging allows an approximation of rock com-position to be obtained and an assessment of bedding frequency and laminations. Velocity measurements incorporate the effects of fracturing. The rating requires scores for the intact rock, bedding/cohesion, and defects. These are combined to yield a Geophysical Strata Rating (GSR). Determination of the GSR is objective and repeatable. GSR values are typically between 20 and 80 and can be related to the Coal Mine Roof Rating.

Jan 5, 2007

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.3 and 2.6 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year production period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 indexes. Initial capital investment is $34.6 million for the 1.3-MM-tpy mine and $63.5 million for the 2.6-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $50.8 and $92.2 million, respectively. These figures translate into total capital investments of $38.51 and $34.91 per ton of annual production. Assuming a desired 15-percent discounted cash flow (DCF) rate of return, with Federal income taxes at 50 percent, the required selling prices would be $13.41 and $12.27 per ton for the 1.3- and 2.6 -MM- tpy mines.

Jan 1, 1976

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

THE machine from which the following results were obtained makes one of a row of seven at work in the Junction North, Concentration Mill at Broken Hill, New South Wales. It consists essentially of a belt for dressing purposes, which travels round two 12-in drums situated at either end of a wooden frame. This frame is supported on wooden legs, and the whole is affixed to two iron castings, one on either side of the frame. A to-and-fro motion is obtained from an eccentric shaft, which, together with the stationary end of the supporting legs, is carried by the iron castings. A belt drive to the forward drum provides a constant rate of travel to the dressing belt.The top half of the dressing belt is supported on 3-in rollers spaced about 12-in centres along the frame of the vanner. A fairly thick dressing belt is used, and no trouble whatever is experienced from the formation of gutters between the rollers.These belts are 28 ft 4 in long, 4 ft wide, 3-16 in thick, and are made of two-ply 32-oz duck, with a coating of rubber on either side. The surface available for dressing is about 10 ft 6 in x 3 ft 8 in- ie, about 38'5 square feet. The machine is driven atthe rate of 245 i-in strokes per minute, while the dressing belt travels at 15 feet per minute...

Jan 1, 1909

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009