Search Documents

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By R. S. Olsen

Although aluminum is easily leached from calcined clay with boiling mineral acids, the presence of fines and slimes in the leached residue has hindered the application of acid leaching processes. A feed preparation method was, therefore, devised that provided a dense, smooth-surfaced, fine-grained clay. The important factors affecting feed quality were determined to be (1) crushing the raw clay to the size desired for the leaching process, (2) moistening the crushed clay with a fine mist of water while tumbling on a rotating disk, (3) drying the misted clay, and (4) calcining the dried clay at 750° C in a fluidized bed. Clay treated by this method was leached with HCI, and its residue was washed by water displacement in 4-ft-deep beds. Bed permeabilities on the order of 47 darcys or 4.6 x 10-7 cm2 were obtained with the leached residues.

Jan 1, 1983

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

Increasing depths and mechanization of underground mines have led to the production of large amounts of gaseous and particulate contaminants. Over 100 000 lives have been lost due to methane gas and dust explosions in coal mine workings in both the United States and Canada since 1900. There is, therefore, the need to constantly assess and evaluate the performance of existing mine ventilation systems to maintain safe and acceptable mine environmental conditions. This paper advances research initiatives in the control of methane gas in underground mine environments. It uses the results of continuous monitoring of methane gas concentrations conducted in selected coal mines in North America to assess the effectiveness of existing auxiliary ventilation systems to control methane gas concentrations. The results show that the average quantities of fresh air required to dilute, disperse and remove methane gas concentrations within set levels of one minute varied from 5.43 m3/sec. to 27.97 m3/sec. in the development headings. The average dilution times in the headings studied were less than eight minutes. The calculated dilution efficiencies of the auxiliary ventilation systems in the headings varied from 12% to 139%. These efficiencies ranged from poor to excellent. This implies that the auxiliary ventilation systems were capable of controlling the methane gas concentrations below statutory levels but may not be able to cope with large and unusual methane gas concentrations in the headings. This study is significant in the control of methane gas and coal dust explosions in coal mines.

Sep 1, 2001

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008

By Jean M. Richardson, Steven R. Williams

"Geometallurgical mapping is a new team-based approach that documents variability within an orebody and quantifies the impact of geology (host rocks, alteration and structure) and mineralogy on grinding, metallurgical response and metal recovery processes. The quantitative, spatially constrained database that results can be readily integrated into 3-D block models and mine planning activities. Thus it is an important tool to reduce the technical risk associated with new mine developments or expansions.Normally undertaken during pre-feasibility or feasibility planning stages, the first step of geometallurgical mapping is to review the geology, mineralogy and other critical parameters and construct a geometallurgical matrix. This matrix provides an objective base to then guide sampling and/or compositing activity for physical property and metallurgical testing. Depending on the project, an array of testing techniques can be used to characterize the ore and feed data into the geometallurgical model.While the range and number of tests needed is project-dependant, the geometallurgical mapping approach allows the development of empirical models or interdependent relationships, grounded by spatially-constrained real data. Extensive data sets collected using less expensive testing methods can be meaningfully correlated with results from complex specialty tests to yield realistic metallurgical recovery data.With geometallurgical mapping completed, the resulting database can be integrated into an overall 3-D block mine model. This means that metallurgical response can be used to realistically forecast the recoveries of specific blocks, perhaps sampled only by drilling. Mine planning can then incorporate the forecasted metallurgical response and generate future project cash-flows; opening the door to economic optimization of the mine exploitation."

Jan 1, 2004

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By B. B. Dhar

Slope stability at the proposed mine in Rajasthan was analysed in two dimensions using a finite difference code. The properties of the rock material were determined in the laboratory and subsequently modified to approximate those of the in situ rock mass. Geotechnical mapping was undertaken to determine the critical orientation of structural discontinuities. The results of the work indicated that an open pit 148 m in depth would be stable with overall slope angles of 60 degrees

Aug 1, 1994

By R. A. Meister

The study on improving surface coat refuse disposal site inspections included surface inspections of 15 refuse disposal sites. Monthly aerial photos were taken of the sites and computer methods were used to determine elevation changes. Photogrammetric techniques that were used are described in detail. A comparison of the results of each of these inspection techniques is included. A detailed evaluation of the photogrammetric techniques was made and conclusions were drawn concerning the advantages and disadvantages of using aerial photography and photogrammetry as part of the inspection procedure. Operators' opinions of the aerial photography methods are included.

Jan 1, 1980

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By J. B. Scott

"A computerized cost estimating program developed with the use of the Lotus 1-2-3 spreadsheet program has produced dramatic savings in preparing estimates for operating costs, equipment fleet size and manpower requirements for underground mines.The program is used by Dynatec to support its consulting engineering projects, particularly feasibility studies. The 'first principles' approach is used to prepare detailed estimates under direct labour and supplies categories and maintenance costs for each mining operation . User notes have been developed to guide the estimator and ensure appropriate consideration is given to the specifics of the particular mine.A typical case history is illustrated and the ease by which alternatives and sensitivity analyses can be prepared is demonstrated. IntroductionHistorical MethodsMining engineers have used one or a combination of methods to prepare operating cost estimates for new or existing mine s. Operating companies have access to historical cost data and generally use this for preparing estimates. Consulting engineers do not usually have direct access to such information and must rely on mining companies (the present or previous clients); publications (text books, equipment manufacturers manuals, CMJ reference manual, etc.); annual reports (applicable to public companies); previous studies (to be used with caution as conditions change from mine to mine); and first principles (the subject of this paper), for cost information:Definition of First PrinciplesA first principles approach to cost estimating considers individual primary work elements of an operation. Quantities of work items are developed from the mine plans, production rates, geographic and physical layouts etc. The knowledgeable estimator, assisted by experienced operations personnel, can assign appropriate resources (equipment, labour, supplies and services) to each work element and establish productivities. Completion of the cost estimate is then largely arithmetic."

Jan 1, 1988

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on any type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the ground outside seemed to shake the building as a single, loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By J. R. Thoenen

For several years the Bureau of mines has been investigating the characteristics of ground vibrations produced by quarry blasts. Considerable basic information has been obtained in the course of this study, and the results have been made known to the public through various publications listed in the accompanying bibliography. The studies have been confined to obtaining fundamental knowledge of the characteristics of the vibrations themselves, because it was evident at once that he problem was extremely complicated. It was felt that any attempt to predict the effect of a ground vibration on an' type of artificial structure would be useless until the complexities of building vibrations are better understood. As opportunity offered, teats wore made in various types of structures and the effects of vibrations from many different sources were measured. In one set of tests (5)4/, it was demonstrated that the behavior of a building as quite different if it was shaken by vibrations originating outside tae foundation walls than if the source of the vibrations was within the building; vibrations coming from the round outside seemed to shake the building as a single loosely-coupled structure, whereas mechanically induced vibrations within the house seemed to set floors and walls in motion as independent units, each of which communicated its own natural motion to the adjoining member, causing a very complicated movement that was impossible to interpret.

Jan 1, 1938

The 18th annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held on Saturday, Dec. 2, 2000 at The Westin La Paloma in Tucson, AZ. The 2000 inductee, guest of honor and featured speaker at the banquet will be Ronald C. Cambre, chairman and chief executive officer of Newmont Mining. He will be honored for his role in positioning Newmont as an innovative and key player in the gold mining industry.

Jan 1, 2000

By Benjamin Cebrian

Wall control blasting is an expensive and labor intensive operation. Obtaining a good design is a first step that is not enough to ensure desired results. Experience shows that designs are not always well implemented, not only in the contour blast itself, but also in surrounding production blasts that can affect the final pit wall. In this paper techniques and reference indicators are described in order to audit and evaluate if correct implementation of designs have been done.

Jan 1, 2013