Search Documents

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Américo Pérez

La política ambiental de Centromin Perú S.A. promueve el aprovechamiento de los recursos minerales sin comprometer la capacidad de las futuras generaciones para satisfacer sus necesidades y desarrollo. En ese sentido, los objetivos de la empresa comprenden la protección de la salud y seguridad pública, la prevención del medio ambiente a largo plazo y el uso productivo de las áreas afectadas, retornándolas a su estado inicial. Por ello, el presente trabajo señala los avances en la resolución de los pasivos ambientales de la ex unidad de Casapalca y el Programa de Adecuación Ambiental de la unidad de Morococha, en actual operación.

Sep 13, 2001

By Juan M. Antorena

A dynamic testing program was performed to evaluate installation procedures, assess capacity of 610-mm (24-inch) diameter open ended steel pipe to evaluate set-up and provide minimum pile tip elevation based on the dynamic testing results. The program was performed for a marine terminal project consisting of a 570-meter (1900-foot) long, overwater railroad trestle. The project location is Santa Marta, Colombia, South America. The subsurface profile generally consisted of 4m (12 ft.) of water and soft to hard silty clays. The piles were installed to an approximate tip elevation of -22 meters (MSL). Three piles were initially dynamically monitored during installation and then later monitored during restrike driving to evaluate pile drivability and bearing capacity including time related capacity increases due to soil "set-up". Knowledge of change in pile capacity with time after end of initial driving is important for design of pile foundations.

Jan 1, 1995

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have b en available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on King available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By Foster Fraas

The most important lithium resource in the United States is in the form of the feldspathoid mineral spodumene. This mineral has not been used to any important extent as a source of lithium salts or lithium metal, as other more easily decomposed minerals have been available in sufficient quantity to supply the relatively small demand. The need for cheaper lithium salts for such promising new uses as air conditioning or dehumidification and of lithium feldspar for use in the glass and [ramic] trades has justified the recent work done by the Bureau of Mines on [king] available, through improved beneficiation and extractive processes, some of the lower grade but extensive spodumene deposits.

Jan 1, 1937

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

By E. Chin

The Asia and the Pacific region has large mineral resources of antimony, barite, bauxite, bismuth, copper, fluorspar, gold, graphite, iron ore, magnesite, mica, rare earths, salt, talc and pyrophyllite, titanium, zinc, and zirconium. The region overall lacks large resources of oil and natural gas, but it has large resources of anthracite and bituminous coal. In terms of exploitation, many minerals, metals, and fuel are produced in significant quantities in the Asia and the Pacific region as shown in table 1. Collectively, the area accounts for a substantial amount of the world production of antimony, barite, bauxite, fluorspar, gold, graphite, ilmenite and rutile, iodine, iron ore, lead, magnesite, manganese, nickel, salt, tin, tungsten, and zinc. Total coal production of the region exceeds 1.6 billion metric tons. The production of bituminous coal accounts for more than 80 % of the total output. China is the region's largest coal producer, with an output of almost 1.1 billion tons. Other major producers are Australia and India. The combined production by Australia, China, and India is more than 1.5 billion tons or 93 % of the area's output. The remainder of the coal output in the region comes from Afghanistan, Cambodia, Indonesia, Japan, the Korean peninsula, Malaysia, Mongolia, New Zealand, Pakistan, the Philippines, and Taiwan. The production of crude oil throughout the Asia and Pacific region is close to 2.4 billion barrels. China and Indonesia together account for 67 % of the total output. The remainder of the output is primarily from Australia, Brunei, India, and Malaysia. Indonesia is the largest producer of natural gas in the region with an output of close to 58 billion cubic meters, followed by Malaysia and Australia with 23 and 22 billion cubic meters, respectively. Other producers in the region of lesser stature by output include Brunei, China, India, and Pakistan.

Jan 1, 1993

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By Isabelle Lamb, Manfred K. Lechner, Daniel N. Adams

Sydney Australia’s M5 East Motorway connects southwestern suburbs to the airport. Central to the project are twin 3.8 km roadway tunnels which are mostly driven through rock. In order to come up with the winning tender, the project team developed several unique approaches for tunnel excavation and support. The project’s flat roof with thin shotcrete lining, 20 m wide underground intersections, thixotropic-grout sheathed rockbolts and cablebolts, and new shotcrete testing methods all differ significantly from traditional concepts. This paper presents the design basis and construction methods used to achieve the 100-year design life required by the project’s owner.

Jan 1, 2001

By Fanke Meng

Electrolyzing oxides of titanium, aluminum and niobium could prepare high-Nb bearing TiAl alloy (Ti-45Al-9Nb) at 1500°C. The chosen electrolysis voltage is 3.5V, which is lower than reducing voltage (~4.7V) of electrolyte CaF2, but higher than that of titanium, aluminum and niobium oxides. The investigation shows that compared with traditional methods, this method for preparing high-Nb bearing TiAl alloy is of many advantages such as few steps, friendly environment, low energy consumption, low cost and high current efficiency.

Jan 1, 2009

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By G. I. McPhail

The authors have conducted several investigations into the prediction of the beach profile of high-density tailings and have found that there are a number of important considerations that need to be taken into account over and above the reliability of the beach profile prediction methodology. These considerations relate to the chemistry of the slurry and specifically the influence of pH and flocculation, both of which have a significant influence on the rheology of the slurry at the discharge point. A number of examples are discussed and a potential testing protocol that will assist in assessing the influence of chemistry ahead of the beach profile predictions is presented. A methodology for assimilating the results of the testing into the likely field situation is discussed, and suggestions are made on application of the results in beach profile prediction. The suspected influence of residual flocculation on the stratification

Jan 1, 2012

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the rate of extraction of gold. This is due probably to the activation of passive gold by the thallous ions. Lead, bismuth, and mercury salts, which should produce a similar effect, fail to do so. It is postulated that this latter result, together with the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide.INTRODUCTIONThe work of Fink and Putnam (1950) showed that the rate of solution of gold in cyanide can be increased by the addition of small amounts of lead, bismuth, mercury, and thallium salts. Mills (1951), during a study of the electrochemistry of gold, with particular reference to cyanidation, was able to show that gold may become passive towards cyanide solution. The addition of lead or thallium salts prevented this passivity, although the action of lead was limited to the pH range 10 to 12. In a recent paper Cathro (1963) confirmed the findings of Mills, and presented results which showed that the addition of thallium to a cyanide leach of a calcine from Lake View and Star mine, Kalgoorlie, increased the rate of extraction of gold appreciably. In, this paper the use of thallium to prevent the gold becoming passive, and hence to decrease leaching time and cyanide consumption, is examined.EXPERIMENTALA series of leaching tests was carried out on a sample of Lake View and Star calcine, comprising calcined pyrite (about 70 per cent.) and siliceous gangue (about 30 per cent.) and containing 165 p.p.m. gold, 45 p.p.m. silver, 0·1...

Jan 1, 1964