Search Documents

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By D. Harrington

"Up to the last 10 or 15 years, responsibility for accidents in mines was generally, though not universally, placed upon the person or persons immediately involved. Present-day thought is rapidly veering toward holding the industry responsible for accidents, with ultimate payment of the bill by the consumer, if financial expenditure should be necessary. While it is undoubtedly correct in principle that responsibility for accidents in and around mines should be shouldered by the employer and while it is probable that as time passes the burden will become even more definitely than now that of the mining companies, on the other hand it is an undeniable fact that large numbers of accidents occur through acts of omission or of commission of some person, very frequently the victim of the accident being the offender.Out of about 3,000 persons killed every rear in our -mines and quarries, nearly half or approximately 1,500 of the fatalities are due to falls of overlying material or of persons, about 500 to haulage, about 350 to fires and explosions, about 125 to explosives, approximately the same number to electricity, and about 300 to various miscellaneous accidents.Generally the accidents from falls involve but one or two persons at a time, and the tendency is now as it always has been to charge the victim or possibly a coworker with the responsibility. Usually this sort of accident occurs at or near a working face (statistics indicate that about 80 per cent of fatalities from falls of roof or rib occur near the face), and as it is Generally agreed that it is the duty of the worker to keep his working place safe, the worker and especially the face worker is given the blame in case of accident."

Apr 1, 1930

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

Simulation and Analysis of Media Behaviour in the Tower Mill by Discrete Element Method for Estimating the Power Draw and Spatial Distribution of Grinding Process The trends to the Tower Mill (TM) for grinding the materials are increased recently due to its unique merits. Among the various considerations of this machine, the main important items are increasing the efficiency of grinding as more as possible while keep the power consumption, manufacturing and maintenance costs as less as possible. Because this grinding process includes a huge numbers of media particles (ball or other shapes) that are interacted with each other and body of the machine, the DEM (Discrete Element Method) way is a very useful and essential step to getting confident evaluations. Because the DEM simulation is a very young scientific field and proper commercial software are very rare and still under modification, at first step, a FORTRAN code is developed for DEM simulation of two laboratory Tower Mill models (KM5 and KD5). The simulation and experimental results matched each other properly. Then one another DEM software was implemented to perform simulation of bigger models (huge numbers of balls), meanwhile could handle the complex 3D geometry data. The simulation and experimental results were compared and analysed in detail for not only laboratory but also for industrial models (KW5, KWD5, KWD50, KW300F, KW700F and KW1500) without any manipulation or compromising of the parameters of simulation. Some numeric data of industrial models are hidden here due to confidential reasons. The relative velocity of balls (ball-ball and ball-TM body), dissipate energy, interacted forces and stresses during the process are the key outputs of DEM simulation for design this machine. Therefore the main important processes in a Tower Mill machine are recognised and consequently some horizons of development of this machine are distinguished.

Sep 13, 2010

By C. Lorimer Colburn

"The diverting of men from industry to combat in the world's war focused the attention of the operators in this country upon mechanical means of doing things. The demand for man-power -was so insistent that every available agency for multiplying it had to be employed. It was during the 1period of the war and immediately thereafter that development of the use of underground loading devices made most rapi4 progress. In all parts of the United States, mining engineers and mine managers were diligent in their efforts to develop mechanical loaders. The mining engineers of the U. S. Bureau of Mines in every section of the country have secured, with the cooperation of the mine operators, data on the actual performance of the mechanical shovels in their districts, and have made them available to the author of this paper.No effort has been made to discuss exhaustively the subject of underground loading devices. It has been the object to collect together in one paper, records of the performance of all machines now in actual use. Improvements in the design of machines are constantly being made the performance records given in this paper relate to operation prior to March 1 1 1921. The records prior to 1920 cay not fully represent the work that could be accomplished with the present models of the same machine.The data secured are given exactly as reported by the mine operators. Since this data were collected there have been two underground loaders, of a different design, put into operation in the iron mines of the Lake Superior District. One is the John Mayne Sub-level loader, being tried by the Cleveland-Cliffs Iron Co., Ishpeming, Mich., and the other is the Cole-Goudie shovel, being tried by the Oliver Mining Company, at Ironwood, Mich. No information has been secured regarding the performance of either of these machines."

Oct 1, 1921

By A. R. Biggart

Twenty-sixth Sir Julius Wernher memorial lecture, presented at the Tunnelling '94 symposium held in London, 5-7 July 1994. In describing 18 projects with which he has been involved over a period of 36 years, the author aims to illustrate how technological change and an increase in scientific knowledge have influenced tunnelling practice, which he nevertheless maintains does continue to be an art. Tunnels discussed are: the Silver Street, Blackfriars, Whitechapel, St. Paul's and Waterloo Post Office tunnels, 1958-1969; metro tunnels on the Victoria Line, London, 1962-1970; the introduction of tunnel boring machines (TBMs), 1971-1978, in the Empingham reservoir diversion tunnels in Rutland, the bentonite tunnelling machine experiment at New Cross, the Southern tunnel water main section of the London Ring Main and the Warrington sewer in Cheshire; tunnels in rock 1975-1981, for the Lune Wyre and Megget Manor aquaducts, Weymouth sea outfall and Bristol interceptor sewer; Priestley TBM tunnels 1969-1982; the Greater Cairo wastewater project 1983-1987; Anacostia River crossing, Washington DC 1985-1987; the Channel Tunnel 1987-1992; and the Storebaelt eastern tunnel in Denmark, 1992-1994.

Dec 1, 1994

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth's crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By Cory Dippold, Michael Mett, Jérôme Steinkühler, Kristi Latimer

For decades, tunnels of all types have been a significant part of our infrastructure. In particular, water tunnels carry millions of gallons of fresh water every day to major metropolitan areas and surrounding communities. As a critical piece of public health infrastructure, it is important to inspect the condition of these tunnels regularly to ensure reliable and continuous operation. A specific challenge with water infrastructure is that it’s often difficult or impossible to shut down the system for long periods of time to perform the needed inspections. The latest method of tunnel condition assessment is the use of hybrid reality 3-D scan data. Photogrammetric and LiDAR based 3-D data ensure a reliable and objective view of tunnel conditions. The data can be used to support a detailed digital inspection including the compilation of databases that consist of a wide variety of deficiencies such as cracks and spalls within the structure. Mott MacDonald, a design engineer company worked closely with Dibit, used a 360-degree scanning system to collect high-resolution photogrammetric and LiDAR data on a recent project involving a water tunnel. The allows for full 360-degree coverage of the tunnel surface including a water covered invert. It operates at walking speed and ensures a fast and reliable data acquisition which can reduce the time of tunnel shutdowns. Several allocated inspection weeks can reduce to few days, with the final work product being a higher quality and more complete deliverable than traditional inspection methods would have provided. The true-color 3D-model has a photo resolution of 1 × 1 mm (0.039 × 0.039 inches) which makes cracks visible with a width of down to 0.3 mm (0.011 inches). The assessment of water tunnels, its technical challenges and the results of the 3D-tunnel inspection case study are illustrated and described in this publication.

Dec 1, 2022

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By M. J. Fairweather

"The development of means to maximize the selectivity between galena and sphalerite in lead zinc ores is extremely important to the lead-zinc industry. Two challenging studies recently undertaken by Cominco will be reviewed. The first required an unusually fine grind to achieve liberation between galena and sphalerite. The second contained partially altered galena which resulted in unusual early activation of sphalerite under normal flotation conditions. Means by which lead and zinc separation were optimized in these two ores will be discussed.There are two important factors in the separation of minerals by froth flotation: particle size distribution (grind) and pulp chemistry. Pulp chemistry includes a number of factors including pH, Eh, collector type and concentration, inorganic depressants, organic depressants and activators.Grind is important for two reasons. A sufficiently fine grind is required to optimize liberation. However, if the mineral dissemination is too fine, mineral selectivity in the flotation process is impaired. Due to the hydrodynamic constraints of conventional mechanical flotation cells, flotation works best over the single decade size range between 10 and 100 microns. The majority of new ores treated by Cominco until relatively recently were comparatively simple. The major factor in their treatment was defining optimum grind size. Accordingly, the focus within mineral processing at Cominco was on grind and supporting liberation studies. The relationships between grind, liberation and flotation response are intuitively easy to understand. An idealized relationship is shown in the first figure."

Jan 1, 1991

By Georgios Bartzas, Vasiliki Karmali, Konstantinos Komnitsas, Anna Kritikaki, Dimitra Vathi, Stylianos Tampouris, Arne Peys

Large volumes of slags, with varying mineralogical and geochemical characteristics, are produced annually by the ferrous and nonferrous metallurgical industry. Most of them are considered as potential secondary resources and may be valorized, following the principles of circular economy, for the recovery of critical elements, including energy transition metals. Apart from the economic benefits, valorization of slags may contribute to the competitiveness of the metal industry and the conservation of natural resources. Valorization also results in minimization of environmental impacts on soils and waters in slag disposal areas, due to the prevention of solubilization and subsequent migration of potentially hazardous elements. The present study utilizes ferronickel (FeNi) slag for the production of alkali-activated materials. The effects of the main experimental parameters, including sodium hydroxide (NaOH) molarity, silica/sodium oxide (SiO2 /Na2O) molar ratio in the activating solution, precuring and curing time, curing temperature and aging period on several properties of the final products, are assessed.

Apr 1, 2025

By Nicholas Zabaras, Deep Samanta

"Solidification of metal aluminum and aluminum alloys is modeled on uneven surfaces characterized by sinusoidal curves. Wavelengths and amplitudes of these sinusoidal surfaces are varied to study their effects on processes like solidification, macro-segregation and inverse segregation. Solidification and macro-segregation are modeled using a slightly modified form of a stabilized finite element method developed recently to model high Rayleigh number solidification and porous media flows. For pure metal solidification, the effect of varying amplitudes and wavelengths is observed in heat transfer, fluid-flow ~nd phase change processes. The relative importance of shrinkage driven flow and solutal convection on the redistribution of solute for an alloy solidifying in a rectangular cavity is compared. The analysis is then extended by modifying one of the surfaces to a sinusoid. In this case the effects of varying amplitudes and wavelengths are studied in heat transfer, fluid flow, phase change, macro-segregation and inverse segregation processes.1 IntroductionTransport phenomenon during solidification of alloys is a major cause ofcasting defects such as segregation, micro-voids, hot tears, porosity, internal and surface cracks. Heat flow across metal and mold surfaces directly affects the phase change process and plays an important role in determining freezing conditions within the metal. In alloys, natural convection and shrinkage play an important role in determining the final solute redistribution, macrosegregation and evolution of solid macromorphology. Surface unevenness plays an important role during the early stages of solidification. It influences the heat transfer rate and fluid flow in the melt, which in turn affect the morphology and shape of the solid-liquid interface. The effect of surface unevenness on solute redistribution is important during solidification of alloys, where solute driven flow in the mushy zone is prominent. Thevik and Mo in [7] and [8] used a one dimensional model for studying surface segregation and macrosegregation in alloys under the influence of exudation and solidification shrinkage. Air-gap formation in their model was expressed through a variable convective heat transfer coefficient at the boundary. Tsai et al. in [3] and [4] have modeled macrosegregation in an aluminum-copper alloy driven by shrinkage and solutal convection. They used a single domain model based on mixture theory and solved the transport equations using finite difference methods. Our aim is to model solidification of aluminum followed by macrosegregation and inverse segregation in aluminum-copper alloys on uneven surfaces by finite element methods. These surfaces are modeled as sinusoids characterized by amplitudes, ?s and wavelengths, As, By varying As and ?s, changes in heat transfer, fluid flow, phase-change and macrosegregation are studied."

Jan 1, 2004

By Y. M. Jiang

A users friendly PC Computer Program has been developed to implement a systematic design of the powered support. The required input data are: (1) thickness, RQD, and compressive strength of the immediate roof; (2) mining height; and (3) type, thickness, and tensile strength of the main roof. Several important parameters for support selection under a given geological condition are generated through the implementation of the program, including type of support most favorable for the geologic condition, minimum inclination angle of the legs with respect to the horizontal axis, suitable setting load ratio of the front to rear leg for the 4-leg supports, optimum setting load, and support capacity.

Jan 1, 1989

By K. W. John, L. Mueller

The rock mechanics approach to stability problems of steep rock slopes dealt with in this article has particular reference to the concept and methods of analysis developed by the Salzburg, Austria, school of rock mechanics. These theories are based on the principal postulate of the anistropy of the technological properties of in-situ rock masses. The present approach, which is more in line with geological engineering concepts, differs distinctively from the soil mechanics and engineering geological concepts commonly practiced in the United States. PRINCIPAL ENGINEERING APPROACH TO GEOTECHNICAL PROBLEMS AVAILABLE ENGINEERING CONCEPTS At the present time two different concepts are available for engineering analysis of underground structures and foundations in different earth material: soil mechanics and rock mechanics. Of these two branches, soil mechanics is, after 40 years of initially revolutionary and more recently evolutionary development, well established. Its principal concept of replacing in-situ soils or rock masses by perfectly homogeneous substitues has resulted in many practicable methods of analysis which, if applied with judgement, have resulted in successful applications throughout the world. Conversely, rock mechanics is still in the early stages of revolutionary development. Few, if any, standard concepts or methods of analysis have been established. Opinions vary widely. At present the professional background of an investigator very often determines the engineering concept to be applied to a particular problem, rather than its actual requirements if considered objectively. This paper stresses the rock mechanics or geological engineering point of view advocated by the Salzburg group. A review of the soil mechanics concepts is considered beyond the scope of this paper. THE "SALZBURG APPROACH" TO ROCK MECHANICS The rock mechanics concept as outlined here was initiated by Stini, based upon work by sander.1 Since

Jan 1, 1963

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964