Search Documents

By Barbara Mazzini Loureiro

As placas de circuito impresso (PCI) são materiais heterogêneos e sua composição pode variar em função do ano de fabricação, tecnologia empregada, propósito de utilização, legislações vigentes e país de origem, entre outros. Essas características interferem diretamente no valor econômico agregado a estes resíduos, pois dependem da composição dos mesmos, de tal maneira que as empresas recicladoras tomam como base essas informações no momento da aquisição da sucata. Assim, a classificação e caracterização de PCIs é de suma importância para o mercado de reciclagem de resíduos eletroeletrônicos. A fim de alcançar este objetivo foi realizada cominuição em moinho de facas utilizando grelhas com abertura de 9, 6 e 3mm. A etapa de caracterização incluiu ensaios de digestão em água régia, perda ao fogo, análises química quantitativa por ICP-OES e MEV/EDS. Verificou-se que o lote de PCI estudado possui 39,5% de material cerâmico, 34,5% polimérico e 26 % metálico. A porcentagem em massa de cobre na placa é de 14,28%, de ferro 3,73%, de ouro 0,012% e de estanho 1,29%. O lote não é lead free e é multilayer com quatro camadas de cobre.

Aug 8, 2018

By T. T. Chen

Copper anodes generated from copper scrap are relatively rich in Sn, Zn and Fe. Because of the presence of oxygen, only trace amounts of Sn occur in solid solution in the copper crystals. Thus, Sn occurs mainly as SnO2, Cu-Sn-Ni oxide and Sn-Ni-Zn oxide in the copper anodes, and Zn and Fe occur mainly as minor constituents in the Sn-Ni-Zn oxide and Cu-Sn-Ni oxide. During electrorefining, these oxide species are liberated from the copper anodes and report directly to the anode slimes. The trace amounts of Sn present in solid solution in the copper crystals dissolve but reprecipitate as Sn arsenate or a Sb-As-Sn-O phase. Accordingly, high Sn contents in copper anodes do not lead to elevated Sn concentrations in the electrolyte.

Jan 1, 2010

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By S. Storchheim

MORE and more attention is being paid to the bonding of metals in their solid states. For a better understanding of this technique for joining metals and how it is affected by changes in temperature, pressure, and time at temperature and pressure, a detailed report concerning nickel to aluminum bonding has been published.' In order to broaden the knowledge accrued, some additional work concerning solid state joining of aluminum to copper and aluminum to zirconium was performed. The investigation of the Al-Cu system was considerably more extensive than the investigation of the Al-Zr system. For the A1-Cu system, not only were tensile sudies made but intermetallic penetration rate investigations also were carried out. The effect of temperature on intermetallic penetration rate for the A1-Cu system was determined at 11 tsi pressure, held 2 min. Procedure Apparatus: The hot pressing technique was the means of solid state reaction used and required the equipment depicted in Fig. 1. The following procedure was involved: The two metals to be reacted were placed in an aquadag-lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diam made of the same material. A thermocouple well was located in the die body 3½ in. down from the top of the die, while another well was located centrally in the bottom punch 8½ in. from the bottom of the die. This die assembly was located in three cylindrical ceramic heating furnaces placed in tandem. Each furnace was controlled individually by a Variac power transformer. In turn, the die and furnaces were placed in a water-cooled stainless steel pot which could be evacuated. A cover, which contained a centrally located Wilson seal with an 18-4-1 1 in. diam ram running through it, was bolted on the pot. After sealing, the pot was evacuated by a roughing pump to 200 microns pressure, after which a diffusion pump was used to bring the pressure down to 5 to 15 u. At this pressure, the furnaces were turned on. As soon as they started to heat, out-gassing of the entire unit raised the pressure to 30 to 400 p. By the time the specimens were at temperature ready to be pressed, approximately 4/2 hr, the vacuum pumps had re-established the 5 to 15 u pressure. Once the desired temperature was reached, the required pressure was applied for a predetermined length of time to the 1 in. ram, through to the top punch, and to the specimen. When the time for keeping the specimen under pressure had elapsed, the pressure was released, the energizing coil current turned off, and the assembly allowed to cool. After cooling, the die was removed from the pot and the specimen was ejected. Specimen Preparation: Two different types of specimens were made for this investigation. One was for subsequent tensile testing, while the other was for determination of intermetallic alloy zone penetration into the parent metals. Tensile Bars—Commercially rolled copper pieces in. thick or zirconium sheet pieces 1/32 in. thick and 1.366 in. diam were placed between commercial 2-S aluminum rod 1 in. thick and 1.366 in. diam. This sandwich in turn was slipped into a 2-S aluminum sleeve 1.438 in. OD and 1.370 in. ID. This sleeve lined the couple up and prevented the aquadag lubricant from getting in between either the A1-Cu or Al-Zr interfaces. Immediately prior to the specimen assembly, the copper or zirconium was abraded on the flat surfaces with 320 grit silicon carbide paper, producing clean smooth surfaces. The aluminum was chemically cleaned just before assembly by: l—degrease in acetone, 2—distilled water rinse, 3—immersion for 3 min in 5 pct NaOH at 70" to 80°C, 4—distilled water rinse, 5—immersion for 2 min in 50 pct HNO3 solution at room temperature, 6—distilled water rinse, and 7—drying in a blast of gas. After the A1-Cu sandwiches were hot pressed and ejected, the specimens were machined such that the aluminum sleeve was removed, and the remaining aluminum was then threaded; the bar so produced was tested later for tensile strength. In all the instances where Al-Cu couples were tested, the specimens broke during the test at the Cu-A1 interface and never within the aluminum or copper. The ultimate tensile strength values at times showed considerable scatter for a set of given reaction conditions. Because of this, as many as three to five specimens were made for a particular set of conditions. The trend of the average tensile strengths obtained was not as conclusive as was the trend of the maximum tensile strengths, the latter values being obtained under optimum reaction conditions. Therefore, the values of ultimate tensile strength given herein are maximums.

Jan 1, 1956

The design, specification, and performance evaluation of the Communications and Location portions of a Coal Mine Rescue and Survival System are described. The work was performed as part of a nine month effort to develop a mine rescue and survival system using existing technology and state -of-the -art hardware as recommended by the National Academy of Engineering. Three basic subsystems were developed, one for survival, one for communications/location and one for rescue. This report and related equipment manuals describe only the Communications/ Location Subsystem which was designed, fabricated, and tested by the Westinghouse Georesearch Laboratory in Boulder, Colorado. Two basic technologies were used. Electromagnetic signals propagating through-the-earth provide voice downlink and coded beacon up-link communications. Seismic methods were developed to provide means for locating trapped miners. Seismic signalling also provides a backup means for communications. Parallel development programs for the electromagnetic and seismic portions of the system were conducted. The resulting hardware and software have been partially tested in coal mines and under simulated emergency conditions in order to evaluate system performance. The results of these tests are discussed. Further testing is recommended in order to establish quantitative performance limitations tinder a variety of environmental conditions and to develop methods for improving system performance.

Jan 1, 1971

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By J. O. Marsden

Parts I and II in this series of papers presented the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical development of a process to effectively recover copper using medium-temperature pressure leaching and direct electrowinning (DEW). Key features of the process were the use of superfine grinding of the concentrate (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160ºC and 1,380 kPa (200 psi) oxygen overpressure, DEW to produce LME Grade A cathode, recycling of the lean electrolyte to the pressure leaching step and treatment of a lean electrolyte bleed by solution extraction (SX). Recycling of the lean electrolyte provided all of the acid required to effectively dissolve copper and convert approximately 65% to 70% of the sulfide sulfur to elemental sulfur, resulting in an ?acid-autogenous? process referred to as the ?MT-DEW-SX? process. This paper (Part III) discusses the steps taken to develop and complete a large-scale demonstration of the process at Bagdad, Arizona, in 2005.

Jan 1, 2007

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By M. K. McCarter

The history of mining education, like the history of the mining industry, is typified by “boom and bust” cycles. In academia, the perpetual problem can be stated as “too many graduates for the jobs or too many jobs for the graduates.” The deep “bust cycle” that spanned the 1990s through 2003 spawned renewed efforts to eliminate, consolidate, restructure, rename, reinvent or otherwise change mining education to make it (for some) more fiscally or socially acceptable. During this period, a number of mining programs were eliminated, and by the late 1990s senior people in academia and their counter-parts in industry became increasing concerned about the very real possibility that strategic disciplines may disappear altogether. As a result, the Mining and Metallurgy Society of America (MMSA) created an educational committee to explore how industry could help preserve key programs necessary to provide future professionals. Several meetings were held to assess the problems and look for solutions. In 2004, this effort culminated in the first of the “Engineering Education” sessions to be held at the SME Annual Meetings. In response to the information presented in this first meeting, Marc LeVier (then president of MMSA) invited a number of the participants to reconvene the following day. An action plan was formulated and a task force was organized. To more fully represent all industry sectors, SME later that year assumed the sponsorship role for the task force.

Jan 1, 2007

One of the seminal pioneering papers in reserve evaluation was published by Danie Krige in 1951. In that paper he introduced the concept of regression techniques in providing better estimates for stope grades and correcting for what later became known as the ‘conditional bias’. In South Africa, the development of this approach led to the phenomenon being dubbed the ‘regression effect’, and regression techniques ultimately formed the basis of simple kriging in Krige’s later papers. In the late 1950s and early 1960s, Georges Matheron (1965) formulated the general theory of ‘regionalized variables’ and included copious discussion on what he termed the ‘volume-variance’ effect. Matheron defined mathematically the reason for, and quantification of, the difference in variability between estimated values and the actual unknown values. In 1983, this author published a paper that combined these two philosophies so that the ‘regression effect’ could be quantified before actual mining block values were available. In 1996 and in some earlier presentations, Krige revisited the regression effect in terms of the conditional bias and suggested two measures that might enable a practitioner of geostatistics to assess the ‘efficiency’ of the kriging estimator in any particular case. In this article, we revisit the trail from ‘regression effect’ to ‘kriging efficiency’ in conceptual terms and endeavour to explain exactly what is measured by these parameters and how to use (or abuse) them in practical cases.

Jan 1, 2015

Ilmenite production in Western Australia commenced in 1956. There are now five producers, all in the Bunbury-Capel district, and current total production capacity is about 450,000 t.p.a.The deposits occur near the surface and average between 10 and 50 per cent heavy mineral. About 70-85 per cent of the heavy mineral is ilmenite. Other heavy minerals present include leucoxene, zircon, rutile, monazite, and garnet. The ilmenite contains 52-60 per cent Ti02. and is very low in chromium (0·03-0·04 per cent CrS03)Mining is done by sluicing, drag line excavation, or dredging. Primary concentration of the heavy minerals is achieved by spirals, revolving cones, or Reichert cones. After drying and screening, ilmenite is separated from the heavy mineral concentrate by various types of magnetic separator.Separate leucoxene, zircon, rutile, and monazite concentrates are also produced. Each plant uses a different technique and the processes used include chemical attritioning, screen plate electrostatic separation, high tension rolls, air tables, and dry launders.INTRODUCTIONThe treatment of beach sands in the Bunbury/Capel area for the extraction of ilmenite is a very recent development in the mining industry in Western Australia. Nevertheless, since the commencement of production in 1956, ilmenite has become the sixth most important mineral produced (Table 1).The increasing world recognition of Western Australia as a major producer of ilmenite (Table 2) is due primarily to the low chromic bxide content of the mineral (0' 03-0' 04 per cent Cr203), combined with a medium to high titanium dioxide content (54-60 per cent Ti02), supported by large reserves, a stable government, and close access to good shipping facilities. Ilmenite is. produced from these deposits at low cost which enables the industry to compete on world markets despite high rates for sea freights because of the distance from major markets.

Jan 1, 1965

By David C. Oyler, Hakan Gurgenli, Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

Dumper operators are frequently exposed to whole body vibration (WBV) in surface mines. Surface mining activities involve the amalgamation of comparatively high intensity of vibration and extended exposure durations. Efficient risk reduction mandates knowing of important phases of a task that poses a threat to health of dumper operators. So far in India very limited studies have been reported on WBV exposure with regard to surface mines. This paper evaluates WBV of dumper operators based on ISO 2631-1:1997 Standards and European Union (EU) Directive 2002 for different phases of job cycle. Six dumpers were considered for this study and the vibration measurements were made for all the four phases of the job cycle by placing the triaxial accelerometer on the operator’s seat-surface and at the seat-back, independently. The findings of the study revealed that the haulage task (loaded travel and empty travel) remains the chief contributor to vibration exposure according to seat-surface and seat-back measurements. Maximum frequency weighted root mean square (RMS) of 1.12 m/s2 and 1.09 m/s2 were reported for empty travel task for seat-surface and seat-back measurements, respectively. For seat-surface measurements based on RMS, Z axis remains as the dominant axis of vibration for all the dumpers during haulage task, whereas for seat-back measurements, the dominant axis varies between X and Y. Exposure action value (EAV) based on RMS has exceeded the threshold value of 0.5 m/s2 for all the dumpers during loaded travel and empty travel for seat-surface as well as for seat-back measurements.

By Vijaya Thangavelu

Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. High salinity of water supplies and soils in the vicinity of nickel laterite ore bodies is a major abiotic stress to fungi and represents a major challenge in the application of bioleaching process in-situ. Salinity exposes fungi cells to Na+ toxicity and osmotic stress. This study examined the salt tolerance development of Aspergillus foetidus based on gradual acclimatization of organism, its salt threshold and the salinity effect on its metabolism. The biological leaching of weathered saprolite ore with the resulting halotolerant organism under saline conditions was assessed. It was observed that salinity stress affected the organism?s growth and energy utilization

Jan 1, 2006

By C. J. Bise, D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard- recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Feb 24, 1997

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001