Search Documents

After a short theoretical comparison of various typical large bell tops with the bell-less top for segregation and other ,ffects on the material flowing through the equipment proper, a comparative analysis between classical and the new burdening in the furnace is given, showing the theoretical effects of distribution and segregation on the horizontal pressure variations, temperature values and gas composition in the stack. Then some typical theoretical charging patterns of the bell-less top for wall and centre temperature adjusting, pressure drop corrections, dissymmetric local action for blow-in and scaffolding are described. Finally the available practical results on furnaces equipped with the bell-less top are compared with the theoretical statements made before and conclusions indicate that the new approach to burdening blast furnaces is a real improvement.

Jan 1, 1975

By L. E. Cardwell

This publication contains routine analyses and related source data for 377 natural gas samples from 19 States and two foreign countries. Of this total, 373 samples were collected during calendar year 1970. The remaining four samples were collected during previous years, but releases granting per-mission to publish the analyses were not received until 1970. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Twelve previous publications have presented the results of 9,050 gas analyses prior to 1970. The first three, Bulletins 486,6 576,8 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1971

By Tristan Worsey, Nathan Rouse, Kyle Hall

Drilling accuracy is the foundation to any successful blast operation. Even the best blasting practices cannot overcome poor drilling and still obtain desired results. Inaccuracies in boreholes can result in flyrock, increased vibration, uneven floor, and other undesired effects. As depth increases, variation in actual burden and spacing is expected even if collars are located precisely. Problems arise when this deviation reaches a point where it adversely affects the function of the blast design. Not only can unsafe conditions such as insufficient burden at the face develop, but poor fragmentation can compound adverse effects. As with any troubleshooting, problems cannot truly be fixed if they cannot be measured. As a result, significant work has been done in the past on this subject. Currently, there are both cheap and expensive methods used to quantify deviation for a given borehole. However, implementation of these techniques is limited. In general production blasts, little is known about the variance in designed versus true borehole geometry. This is especially true if the blaster does not see telltale signs of drilling deviation. However, losses in blast performance may exist and provide an opportunity to obtain better fragmentation and reduce fines. As drill and blast operations strive for better optimization, greater focus is being placed on drilling accuracy and solutions to this problem. The following paper details the use of several current methods for deviation measurement in order to help prevent compromises of safety and improve overall blast performance.

Jan 1, 2018

By John T. Metcalf

The assembly procedures for nine different wire rope terminations used in the mining industry are presented in a format and manner to facilitate training and to provide points where inspection of the termination should be performed. The nine terminations addressed are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Sleeve & Thimble, Thimble Splice with Four Tucks, U-Bolt Clip & Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The manual was prepared to be used primarily for field type mining operations or training where high capacity machinery is quite limited. It is nut the intent of this manual to suggest that the procedures presented are those to be used by manufacturers or other commercial enterprizes. A different set of procedures may be more appropriate where ideal space and equipment resources are available. The assembly procedures were derived from standard industrial practice, manufacturer's recommendations, and the open literature on the subject. These same procedures were used to prapare test specimens for an extensive series of pull and axial fatigue tests. The results of these tests indicate that these procedures are satisfactory in all respects. This manual is to be used as part of a complete training program. Although a brief glossary is included, there has been no attempt to make this a primer on wire rope. The selection of wire rope termination hardware, like the selection of the wire rope, is a subject not covered by this manual. The reader is cautioned that there are various sources for such hardware and this selection must be done carefully.

Jan 1, 1978

By M. K. Eryadin, I. Yildirim, R. Asmatulu

Novel dewatering aids were tested on various coal samples from the U.S. and Canada in laboratory and pilot-scale filtration experiments. The reagents substantially improved the dewatering kinetics and reduced the cake moistures. The cake moistures were typically reduced from 20-30% by weight to 8-14% range in vacuum filtration. When the reagents were used in conjunction with a pressure filter, higher degrees of moisture reductions were achieved. In the present work, the novel dewatering aids were tested using different types of pilot-scale vacuum filters. The results were consistent with those obtained in laboratory experiments.

Jan 1, 2003

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By David Lin

"Modal data from Red Dog Main Pit ores were collected and analysed on a size-by-size basis. The Main Pit data were compared to data from composite samples of Red Dog Aqqaluk ores. The data revealed that a large fraction of the sphalerite in the Aqqaluk baritic ore was tied up in sphalerite/galena binaries. This provided an explanation for its poor leadlzinc selectivity compared to Main Pit ores. The Aqqaluk vein ore exhibited levels of sphalerite/galena binaries comparable to that of Main Pit ores resulting in comparable lead/zinc selectivity.An attempt was made to correlate the modal and metallurgical data for Main Pit stockpiles. It was found that there was moderate correlation between the percentage of sphalerite locked in binaries with galena in the <C5>C6 size fi-action and sphalerite deportment to the leadconcentrate.INTRODUCTIONTeck Cominco’s Red Dog Mine in northern Alaska is one of the richest zinc districts in the world. Red Dog Mine has been in operation for over ten years and produces nearly 1 million tonnes of zinc concentrate per mum. Red Dog Mine is an open pit operation and current mining is conducted in the area known as the Main Pit. The Main Pit contains proven reserves of about 41 900 000 tonnes of ore grading 19.2% Zn and 5.2% Pb (Cominco 2000). To the north of the Main Pit is the Aqqaluk deposit. It contains probable reserves of 56 100 000 tonnes of ore grading 16.6% Zn and 4.1 % Pb. After the Main Pit has been exhausted, the Aqqaluk deposit will be exploited.The Aqqaluk deposit consists of three main geologic ore types: baritic, siliceous and vein. The siliceous ore type is dominant, representing 64% of the mineralisation. Composite samples of these ore types were created from drill core and batch flotation tests were performed on them. The flotation tests indicated that there were significant metallurgical differences between Main Pit ore and the Aqqaluk siliceous and baritic ore. The siliceous and baritic ores were found to suffer from poor lead/zinc selectivity (Lin 1999, G&T 1999). It was suspected that there were problems with the original Aqqaluk composite samples, thus a new set of composite samples were created and batch flotation tests were conducted again. In this set of tests, the new baritic ore still suffered from leadlzinc selectivity problems, but the new siliceous ore provided excellent metallurgical results. A summary of the flotation results is given in Table 1. Stockpile 132, which is typical of Main Pit ore, is given for comparison purposes. The mineral suite at Red Dog is relatively simple. The ore consists of galena, sphalerite and pyrite in a silicate matrix. The low zinc recoveries of the baritic ore were largely due to sphalerite losses to the lead concentrate."

Jan 1, 2002

By R. H. Atkinson, R. N. Rhoda

An improved technique has been developed for the deoxidation of palladium with aluminum which is especially suitable for use in making small castings with an induction-melting and casting machine. The effect of various crucible linings on the efficiency of the residual deoxidizer and accompanying oxide film in protecting palladium against oxidation during remelting also has been examined; the preferred crucible lining consists of zirconia cement. THE objective of this work was to develop a simple method of deoxidizing induction-melted palladium which would be suitable for use by manufacturers of jewelry and other small castings. In a common method of deoxidizing torch-melted palladium a piece of aluminum foil is dropped on the surface of the molten metal. If a film is present, which is usually the case, it must first be removed by oxidizing the molten metal thoroughly because it would interfere with the entry of the aluminum into the melt. Removal of the film is probably facilitated by a mild fluxing action of the silica crucibles which are used for torch-melting. However, removal of an alumina film from molten palladium in the crucibles normally used for induction melting is a much slower process and it became necessary to modify the de-oxidation procedure. In the modified procedure the charge is simply melted and the desired amount of aluminum, crimped to one end of a tungsten wire, is plunged through the film into the palladium and the wire immediately withdrawn. The trace of tungsten which dissolves along with the aluminum can be avoided, if considered objectionable, by using a palladium wire. In view of the persistence of the alumina film under the conditions of induction-melting it also was decided to ascertain the efficiency of this film in protecting palladium against oxidation during repeated remelting and casting. Melting Equipment and Materials The equipment used for melting and casting consisted of an Ecco GC:6, 6 to 8-kva high-frequency converter and an Ecco M34B centrifugal casting machine. This unit is being increasingly used for making jewelry and dental castings and it also has been found useful in making exploratory melts of a variety of nickel alloys, for which purpose it is well suited on account of its speed of melting and economy of material. A description of the machine and its operation will be published elsewhere.&apos; A common palladium jewelry alloy, 95.5 palladi-um-4.5 ruthenium (referred to as "palladium" in the trade), was selected for the deoxidation tests. It was available as melting stock which had been melted in air to free it from oxidizable impurities, and also as clean scrap from previous melts which had been deoxidized with aluminum. The latter was thought to be typical of clean "palladium" scrap to be found in a manufacturing jeweler&apos;s establishment and it is also similar to one brand of "casting palladium." By the same token, the oxidized melting stock corresponds to "casting palladium" after the latter has been melted and thoroughly oxidized: Pure aluminum wire (99.9 pet), 0.032 in. diam; 1 in. = 0.036 g. Scrap tungsten wire, 0.014 to 0.020 in. diam. Argon, commercial water-pumped; 99.9 pet pure Experimental Procedure Samples of about 50 to 75 g of the palladium alloy were melted in a crucible lined with a proprietary refractory alumina cement. Some charges were melted in air, others in argon. The oxidized melting stock was melted and solidified a number of times in order to remove as much oxygen as possible before deoxidizing, but this treatment was unnecessary in the case of scrap. In either case the metal was deoxidized with aluminum (0.01 to 0.05 pet) by the

Jan 1, 1959

By Joe Shoemaker

Automated Spot Generation ? No Operators below the Highwall ? No Operator Wear and Tear ? Reduced Swing Time ? Single and Double Sided Loading ? Minimized Bench Width

Aug 1, 2013

By Gerald C. Smith

Introduction Newmont Mining Corp.&apos;s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By I. Zaplatynskyj, G. C. Kuczynski

SINCE the excellent studies of metal powder compaction executed by Kamm, Steinberg, and Wulff, no work on the subject has appeared in the technical literature. Kamm et al. were the first to investigate quantitatively the distribution of density in a powder compact, as a function of pressure, height and diameter of the die, powder particle size, etc. For this purpose they devised a very ingenious method. They inserted a thin lead grid into a die and then filled the die with powder. During cold pressing, the lead grid -moved downward. Due to its deformability it followed closely the downward descent of the adjacent powder. The die was then radiographed and, from the deformations of the grid openings measured on the radiographs, the density in the vicinity of each opening was evaluated. Their findings led them to the conclusion that the friction on the side walls of the die is a major controlling factor of the density distribution inside the cold pressed powder compacts. However, it is difficult to conduct tests similar to those of Kamm, Steinberg, and Wulff in a processing plant laboratory, which usually lacks the necessary expensive radiographic equipment. The purpose of this note is to describe a method which makes it possible to determine the density distribution in green powder compacts with the same accuracy as the lead-grid method but which is far simpler and faster and requires only standard laboratory equipment. Instead of using a lead grid, the hardness at selected points of the sectioned compact is determined. If the relationship between hardness and density is known the density distribution is readily obtained. This relationship is easily found from measuring hardness and densities of thin compacts. In such compacts the density, for all practical purposes, is constant throughout. The method was tested on a Plast nickel powder, grade FlA-A20, kindly supplied by Plast Metals Co. Thin compacts (height to diameter ratio 0.2) were pressed in a single action cylindrica1 die at various pressures. The density of the compacts was determined by weighing and by measuring the height and diameter with a micrometer. Subsequently the Rh hardness was determined. Up to ten readings were taken on each specimen. The difference in hardness readings on each compact was never greater than three corresponding to about 0.1 g per cu cm uncertainty in density. By varying the compaction pressure of the samples, a whole scale of densities was obtained allowing construction of a set of density-hardness calibration curves. To test the method several compacts of different height were pressed under varying pressures. Die walls were always well lubricated. After pressing, the compacts were mounted in bakelite and halved by grinding, and hardness readings taken along the diameters of the specimens. The distance between adjacent indentations was about 2.5 mm. After hardness readings were translated into densities, contour maps of densities of the compacts were prepared. One of them is reproduced in Fig. 1. The areas encompassed by the curves are labeled with numbers representing the density in g per cu cm of those regions. In Fig. 2 the same results are re-plotted to emphasize the radial density changes at various depths. The results thus obtained confirm the findings of Kamm, Steinberg, and Wulff kentioned previously. They are recapitulated here briefly. 1—The densest part of a compact pressed from one side is at the outer circumference at the top and the least dense part at the bottom, at the outer circumference. Figs. 1 and 2 show this clearly. 2—The density near the cylindrical surfaces of the compact decreases uniformly with height from top to bottom. 3—The density variation increases with the height to diameter ratio. References R. Kamm, M. A. Steinberg, and J. Wulff: Trans. AIME (1941) 171,&apos;R. p. 439 ;MetaLs Technology (February 1941). R.p. Kamm, M. A. Steinberg, and J. Wulff: Trans. AlME (1949) 180, 2R.P. 694; MetalS Technology (December 1948).

Jan 1, 1957

By James H. Cobbs

The utilization of large diameter drilled holes for mine shafts seems to have had its beginning in Europe about 1850 (28) where the mining industries of Germany and The Netherlands first used drilled shafts. Recent shafts in softer formations of diameters as large as 25 feet and as deep as 1, 700 feet have been drilled in both The Netherlands and Germany. The first shaft drillers utilized cable tool or churn drilling techniques which limit both hole diameters and drilling speeds. Though some churn drilling of shafts is still performed, rotary drilling has been the dominant technique for many years.

Jan 1, 1973

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

Experiments in the bolting of a mine roof were commenced at Elrington Colliery on the South Maitland Coal Field early in 1949, following the appearance of an article in the American publication, &quot;Coal Mine Modernisation Year Book&quot; 1948. Prior to this, although bolting had not been used in the maintenance of satisfactory roof conditions, the principle of roof bolt anchorage had been illustrated in instances such as the hanging of a trolley locomotive power wire using an expanding shell type of bolt anchorage, or the insertion of an eye bolt with a split and wedge, as used to suspend a rope block over a winze being sunk in a metalliferous mine.The experiments at Elrington Colliery were the first efforts in this country to supplement the work of timber supports under a mine roof with systematic placement of roof bolts.Following the series of experiments at Elrington, full scale bolting was commenced at that Colliery in a trackless mobile section in April, 1950.The obvious success of the system at Elrington indicated that it might also be a success in the support of weak roof strata immediately overlying the workable section of the Victoria Tunnel Seam at John Darling Colliery.The system was commenced at John Darling Colliery in April, 1951, in one mechanical section on the Victoria Tunnel Seam, and the scope was gradually widened until by December, 1952, ail&apos;six mechanical units then operating on this seam were working under bolted roofs.

Jan 1, 1954

Several of the larger copper projects recently built have included a molybdenum byproduct circuit as part of the overall project due to the favorable molybdenum market conditions and overall economic contribution to the project. This paper provides a summary of moly plant flotation practices across a number of both recent projects and historical ones. Modern Molybdenum flotation flowsheets predominantly incorporate self-aspirated cells and forced air cells with nitrogen addition. The paper provides insight into the process considerations, capital and operating costs associated with both of the cell types. It also reviews metallurgical aspects and important safety aspects. Other aspects including instrumentation and degree of automation are also discussed along with overall plant design.

Feb 27, 2013

By A. Baldwin

This report describes the engineering feasibility and economic advantages of a unique new mining machine using cutting bits that take a constant-depth linear cut in the coal face. The studies show that this innovative new cutting concept, being developed by the Bureau of Mines, can be designed into the basic continuous mining machine. The resulting miner would be attractive to mine owners because coal could be mined with minimum generation of airborne respirable dust, substantial increases in productivity, and elimination of methane ignition due to cutting.

Jan 1, 1977

By Valois R. Shea-Albin

Increasing pressure from State and Federal agencies to mitigate mining-induced subsidence damage to overlying structures has presented a unique problem to the coal industry in the western United States. Because sandstone escarpments are an environmental issue, millions of tons of coal reserves that underlie these escarpments risk being classified as unminable by regulatory agencies. At this time, the effect of subsidence on escarpments has not been well documented or characterized. The Bureau of Mines is using numerical modeling techniques to analyze escarpment response to longwall mining. Two- and three-dimensional finite element models have been constructed for a study area near Price, Utah, where longwall panels were mined near an escarpment. This status report includes preliminary results showing that the pattern of subsidence surrounding the escarpment can be simulated through numerical modeling. Models that include such structural details as joint and fracture patterns will better simulate subsidence patterns .and magnitude. By locating longwall panels strategically in relation to the escarpment, stability may be preserved throughout the mining process. Numerical modeling provides a method to analyze relatively quickly the effects of longwall panel location and resulting subsidence on escarpment stability. The goal is to provide a relatively accurate predictive tool for mine planning to determine if escarpment stability can be maintained while maximizing extraction of the coal reserves.

Jan 1, 1986