Search Documents

By Basant L. Tiwari

An electrolytic process, based on a three-layer concentration cell, to extract magnesium from commercial aluminum alloy scrap has been examined. The process was repeatedly tested at 1025 K with two cells of d1fferent sizes, 0.6 kg and 5 kg feed aluminum, to have a better understanding of the opera ting parameters and evaluate the scale-up potential. In both cells, the magnesium content of the scrap was selectively reduced ?from 1. 1 to less than 0.1 wt.% at anodic current dens-Hy as high as 1. 1 A/cm2 with current efficiency exceeding 85%. Magnesium was recovered in the form of salt coated globules. Comparison of performances for the two cells suggests that the process can be scaled up. With further development, this process could become a viable alternative for demagging secondary aluminum.

Jan 1, 1985

By Robert W. Freedman, Robert L. Craft, William G. Humphrey

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

DD3-tunnels (PD BH's) ? Rotary coreholes 111no. (124) ? Percussion holes Ono. (37) ? Sampling (rock and soil) ? Soil and rock permeability ? testing ? BH Televiewer Surveys [ ]

Jan 1, 2007

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By George W. Heim

Before and during World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for development included those expected to contain metals of importance in the successful prosecution of the war. This report describes the work performed and results obtained in developing the Daggett Chief manganese deposit near Manila, Daggett County, Utah (fig. 1), during 1941. The work comprised mapping and a study of the geology by the Federal Geological Survey, and bulldozer and hand trenching, sinking of two shafts, and sampling by the Bureau of Mines. Work was started April 17, 1941, and was completed June 28, 1941. Two bulk samples for metallurgical testing were taken.

Jan 1, 1950

By K. Kalgraf

The motion and stability of the metal/electrolyte interface is determined by Navier-Stokes equation. The equation may be decomposed into two independent equations by taking the divergence and curl of Navier-Stokes equation. The divergence determines the motion and stability of magneto-gravitational waves. The curl of Navier-Stokes equation gives an equation containing only velocity and magnetic field, and states that the magnetic field is driving a circulation pattern in the cell, and this magneto-flow has its own stability conditions. The waves are called Alfven waves, and their stability properties are related only to magnetic field and geometry.

Jan 1, 2001

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By M. Yavuz

Equipment selection in mining operations is an important issue, and also difficult to solve in multiple criteria environments. The paper in question has aimed to develop computer software for solving equipment selection problems in mining. In their paper, Basçetin et al. have analysed two case study problems related to open pit and underground mining method selection. By using Yager?s method1, the authors have selected 18 different criteria in the first case study and 21 criteria in the second case study. However, as emphasized by Ozdemir2, in pair wise comparison matrices the appropriate number of criteria should be seven as the maximum, from the point view of validation, consistency and redundancy. In cases where there are more than seven criteria to be handled, it is suggested that the criteria should be clustered and then the maximum number of clusters and subcriteria of every cluster should be limited to seven4.

Jan 1, 2007

By H. -U. Lim, C. -H. Kim

The sixth underground pumped powerhouse cavern is under construction now in Korea. For the stability analysis of the five underground powerhouses, finite element method was used. For this analysis, in-situ rock stresses were measured by overcoring method and horizontal to vertical stress ratio was calculated 1.07-1.32 at four sites. Rock mass strength and elasticity were assumed from intact rock properties. The ratio of elasticity of rock mass was 0.16-0.55 of intact rock core elasticity. In general, elasto-plasticity with Mohr-Coulomb failure criterion was applied and the input cohesion and internal friction angle were approximately 0.12-0.22, 0.6-0.87 of intact rock strength parameters, respectively. Der sechste Untergrund-gepumpt-Powerhouse-Cavern ist jetzt im Bau in Korea. Für die vergan-gene Stabilitätsanalyse des fünf unterirdischen Powerhouses in Gebrauch wurde ein begrenztess Elementsmethode benutzt. Für die Analyse wurden In-Situ Felsenspannungen von overcoring Methode gemessen und Horizontale zu senkrechtem Spannungsverhältnis waren als 1.07-1.32 an vier Stellen kalkuliert. Felsenmassenkraft und Elastizität wurden von unversehrtem Felsenei-gentümern angenommen. Das Verhältnis der Elastizität von Felsenmasse war 0.16-0.55 von un-versehrter Felsenkernelastizität. Im allgemeinen wurde Elasto-Plasticity mit Ausfallskriterium des Mohr-Coulombs verwendet. Die Eingabebindekraft und die innere Reibungswinkel waren unge-fähr 0.12-0.22, 0.6-0.87 von unversehrtem Felsenkraftsparametern, jeweilig. En Coree, la sixieme centrale souterraine de la pompe d'accumulation dans la caverne est en construction. La methode d'element fini a ete utilisee pour analyser la stabilite de cinq dernieres centrales en service. Dans cette analyse, la reaction de la roche sur place etait mesuree par la methode d'overcoring et celle du rapport horizontal-vertical etait calculee de 1.07-1.32 en quatre places. L'intensite et l'elasticite de la masse de roche ont ete estimees de la roche intacte. Quant a l'elastic-ite, sa masse de roche etait 0.16-0.55 fois que celle de la roche intacte. En general, elasto-plasticite avec le critere de defaut Mohr-Coulomb etait utilisee et sa cohesion d'energie et son angle de friction interieure etaient supposees respectivement 0.12-0.22, 0.6-0.87 fois que la parametre de l'intensite de roche intacte.

Jan 1, 2003

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Neil Camarta

$6 Billion Dollar Education ?? Construction is like war ? you need a command and control organization ?? A strong Owner?s team is a must ?? Smaller is better ? break the project into bite size chunks ?? New technology is risky ? lots of construction and start-up risk ?? Safety can be successfully managed ?? Don?t expect contractors to ?work well together? ?? Never, ever let Mining Engineers run stuff than can catch fire

May 1, 2008

By V. Gangrade, J. Addis, S. Vanderslice

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are conducting research to improve the ventilation of large-opening underground stone mines. The mine ventilation in these mines are characterized by: (1) challenges related to keeping airflow velocities high enough to effectively remove or dilute airborne contaminants, (2) low pressure losses needed to move large air volumes of air, and (3) costly stoppings needed to direct ventilation airflows. Each of two field studies was dedicated to specific focus areas. The first focus area was the characterization of underground mine ventilation airflow. The primary means of airflow control in stone mines is through the use of freestanding booster fans. The primary goal of this study was to identify the effectiveness of various fan types and optimize their placement. Both traverse and grid-based airflow readings were taken at various distances from the fans, ranging from 70 ft to 425 ft away from the fan. The air readings were taken using a vane-anemometer and a handheld hotwire anemometer. The data was used to develop precise computational fluid dynamics models. The second focus area was to determine diesel particulate matter (DPM) concentrations in the mine. For large-opening underground stone mines, controlling DPM exposures dictates the design of the ventilation system. Therefore, researchers carried out the DPM sampling campaign to identify potential areas of concern within the mine. The samples collected during the campaign were analyzed using NIOSH Method 5040. The sampling was done using the Mine Safety and Health Administration’s (MSHA) compliance sampling methodology.

Feb 1, 2023

The first record of coal discovery in Australia dates back to 1791 when escaping convicts found coal in the banks of a creek just south of Newcastle. Development in the Newcastle Coalfield was the sole source of supply for the colony and for export until the 1850s when mines were established in the Southern & Western Coalfields. The important Hunter Coalfield was not discovered until 1873 when coal was found at Rixs Creek near Singleton: The first exploration drillholes were commenced in 1799 using drilling equipment obtained by Sir Joseph Banks. From 1820 to 1850 several famous geologists (naturalists), including the Rev W. B. Clarke, J. D. Dana and Strzelecki, wrote reports on the coal measures in New South Wales. The first Government Geo- logist, Samuel Stutchbury, was appointed in 1850. The major coal deposits of the State are contained in Permian Coal Measures in the Sydney-Gunnedah and Oaklands Basins. Coal quality ranges from high volatile, high moisture thermal coal at Oaklands to low volatile hard coking coal in the Southern Coalfield. Most coalfields can provide a range of steaming and coking coals.

Jan 1, 1988

By Otávio da Fonseca Martins Gomes, Renata Hiraga de Vasconcellos Cruz

Maghemite is a mineral formed from magnetite oxidation at low temperatures, an intermediate term of the magnetite-hematite series. Maghemite could be misidentified as magnetite by X-ray diffraction, and/or as hematite by spot chemical analysis. Nevertheless, non-stoichiometric magnetite was detected and quantified in samples of Brazilian soils and iron ores by the Rietveld method refinement of its structure. The results were confirmed by optical microscopy and Raman spectroscopy, thus validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores.

Oct 3, 2019

By David A. Campbell

There has been a long history of ironmaking on the North East coast of England centered around the River Tees. The industry developed here because of the availability of good coking coals to the North in Co. Durham, and the discovery in 1851 of ironstone in the nearby Cleveland Hills, South of the .River. Cleveland ironstone is relatively poor in quality, with an iron content not exceeding h% and high proportion of sulphur and phosphorous. The iron exists in chemical association with alumina and silica, and physical beneficiation processes involve a serious loss in iron unless the upgrading is limited, when the economics of the process become doubtful. Over the years, richer foreign ores have replaced the local ironstone, and the last operating mine was closed in 1964.

Jan 1, 1982

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By Franz Ramstorfer

No lingotamento contínuo de placas, rompimentos de veio pelo colamento e problemas de qualidade de superfície, como trincas longitudinais, são frequentemente relacionadas à lubrificação insuficiente no molde de lingotamento contínuo devido ao pó fluxante ou a prática de oscilação inadequados. Para detectar, com vistas a prevenir, este tipo de problema de processo, um método para avaliar em tempo real o coeficiente de atrito entre o veio e as placas do molde foi desenvolvido, utilizando-se a medição da força que atua nas placas laterais do molde e as forças de oscilação. Observou-se que o coeficiente de atrito do molde é um parâmetro confiável para auxiliar no desenvolvimento de pó fluxante, na otimização de parâmetros de oscilação e no monitoramento online do desempenho de pó fluxante.

Aug 16, 2017

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

By R. A. Cattell

The Bureau of Mines recently observed its fortieth anniversary, and with the close of the fiscal year 1950 it completed 36 years of close cooperation with and helpfulness to the petroleum and natural-gas industries, whose technical problems it studies. Petroleum people likewise observed the ninetieth anniversary of the start of this truly American industry when "Colonel" Drake drilled the first well at Titusville, Pa., in 1859 (see fig. 1). Throughout the period, during which there have been many changes in the fuel and related economy of the country, this work has been carried on systematically by an organized entity of the Bureau first known as the Petroleum Division and in recent years as the Petroleum and Natural Gas Branch. Changes in the industries have been brought about partly by economic forces, partly by advances in technology, and in some measure by the impact of two world wars. As the needs of industry and the Nation have changed, so have the studies of the Bureau changed to meet these needs. Consistently, Bureau technologists and scientists have tried to keep in step with progressive movements; frequently, in fact, have taken the lead. Wherever possible, they have looked far ahead in their program of research, at the same time recognizing the needs of the hour.

Jan 1, 1951

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961