Search Documents

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

To preserve Washington Group International's quality of service in the mine operations area, the company has established a Supervisor Training Program to provide all levels of supervision with the required skills to meet objectives and guarantee consistent, excellent performance for each of our projects. A need developed to establish this training program internationally. The first international training session was held at the APEX San Cristóbal Mine in Bolivia. This paper discusses the program’s development, execution, results, and lessons learned with an emphasis on multicultural environments.

Jan 1, 2007

By A. Peake

Background The CSIR Division of Mining Technology assumed responsibility for the operations of the Hoist Rope and Mechanical Test Laboratories at Cottesloe in April 1999. The laboratories were previously the responsibility of the CSIR’s Division of Manufacturing and Materials Technology, before which they fell under the National Mechanical Engineering Research Institute (also of CSIR). As the focus of this conference is on safety in mines research institutes, it was thought appropriate that this paper should review some of the activities at Cottesloe and its role in supporting mine safety strategies.

Jan 1, 2003

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By J. Hartikainen

19 papers were allocated to this session by the paper classification committee, 8 related to bored piles, 5 to continuous flight auger piles (CFA piles), 3 to slurry trenches, 2 to both bored piles and slurry trenches, one of them also dealing with root piles. There were no papers dealing with root piles only, as root filling is a different technique. One paper concerns sheet piling (Table 1). Table 1. Papers for session 1: Recent Technological Developments in Deep Foundations with Soil Excavation. [ ] Table 2. Classification of pile type in Belgium - van Impe W.F. /10/. [ ] Trends in piling Trends in piling in Central Europe were studied by van Impe for his brilliant lecture to the Finnish Civil Engineering Society. He claimed that bored piling is on the decrease and CFA pilling on the increase (Table 2). Thus the numbers of papers presented here do not conform to recent developments or trends. The papers submitted arc of course influenced largely by the fact, observable in Table 3, that bored piling is

Jan 1, 1994

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the openstopes. Little work has been done in the past to determine pillar strength and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to oversize pillars with consequential loss of ore or undersize pillars resulting in potential collapses or pillar bursts. This paper describes a back-analysis of pillar failures at Impala Platinum, just north of Rustenburg, and provides insights into pillar behaviour. Strength formulae are presented for Merensky Reef pillars at Impala. These formulae may be used cautiously on other platinum mines with similar geotechnical and geomechanical conditions.

Jan 1, 2008

By Thomas P. Mucho, Dennis R. Dolinar, Anthony T. Iannacchione

The Chestnut Ridge Anticline is a prominent structure in southwestern Pennsylvania, USA. This structure has brought two economically valuable limestone formations to the surface, where they are easily accessible to room-and-pillar mining. Nine active crushed stone quarries, an underground research facility, and one industrial facility currently operate along the linear trend that represents the axis of the anticline. The National Institute for Occupational Safety and Health (NIOSH) has identified significant variation in levels of horizontal stress within relatively short distances at shallow overburdens along the anticline. At one quarry, the horizontal stress is high enough to shear strata with a modulus of approximately 77 Gpa. Conversely, zones of extension were observed in parts of another quarry, indicating very low horizontal stress conditions. This study found that high levels of horizontal stress are to be expected in this very stiff rock formation and that local geologic and topographic structures are capable of altering the magnitude and possibly the orientation of the horizontal stress field.

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By P. Wells

"In the past decade, there have been many developments in processing of nickel/copper sulfide ores. Improved pentlandite/pyrrhotite flotation selectivity with the use of new reagents, fine regrinding and Redox measurement (control) has led to increased pyrrhotite rejection and thus higher concentrate grades. Flash flotation has increased overall nickel and associated precious group metal recoveries. Recovery of both fine and coarse particles has been improved through an understanding of flotation cell hydrodynamics. The separation of copper from nickel in such ores has seen a similar level of development. From the late 80s to very recently, the use of flotation columns, the use of pyrrhotite depressing reagents and the improved understanding of the complex mineralogy of chalcopyrite, pentlandite and pyrrhotite have considerably increased copper / nickel separation efficiency. Copper concentrate with more than 30% copper and less than 0.5% nickel grade is now obtainable at 80-85% copper recovery from mill feed compared to 70-75% copper recovery with 30% copper and 1% nickel grade only a few years ago. Improved copper / nickel separation in milling operations has the potential to substantially improve the processing of the resulting concentrates and thus the overall return from the extraction of nickel and copper from sulfide ores.INTRODUCTIONNickel metal by itself or in alloys with other metals and materials makes a significant contribution to modern society. The relatively high price that nickel commands compared to other base metals is a reflection of the fact that, although abundant in the universe, nickel is sparingly distributed in the earth’s crust. There are two types of nickel deposits that are currently being exploited: complex sulfide ores and lateritic oxide ores. Lateritic contain no copper but in sulfide deposits, nickel– bearing minerals, principally pentlandite (Pn, [Ni,Fe]8S9), some millerite (NiS) and violarite ([Ni,Fe]S) are often found in association with copper-bearing minerals, mainly chalcopyrite (Cp, CuFeS2) and cubanite (CuFe2S3). The copper content of such ores can vary considerably from as high as 5-8% (in some Sudbury basin ores) to as low as 0.1% (in ores mined by Western Mining at Mount Keith, Western Australia and by Inco in Thompson, Manitoba). The valuable minerals Pn and Cp are almost invariably found associated with pyrrhotite (Po, Fe7S8) which along with nonsulphide rock has to be rejected to tails in the primary milling stage. The bulk concentrate from the primary stage is then treated to depress Pn and float Cp. A complete Cu/Ni separation at the mill would be highly desirable but this is not possible because of locking between a small fraction of the valuable minerals. As a result, Cu/Ni separation has to be carried out both during milling and during refining of the matte following smelting. At Inco, Jinchuan and in Norilsk, a chalcocite / heazlewoodite separation is made by flotation following slow cooling of the matte. In the present Sudbury Inco operations, Cu/Ni separation has not been conducted at the mill since 1991 and all Cu/Ni separation takes place at the matte processing plant. Because of the rising ratio of Cu to Ni in the ore, this strategy is under review and this paper describes some recent studies of circuits in preparation for possible installation of a copper / nickel separation circuit at Inco’s Clarabelle Mill in the Sudbury area."

Jan 1, 2004

By Bruce D. Hansen

For many years, Newmont has focused on improving its operations. After the merger between Newmont and Santa Fe Pacific Gold, Newmont created synergies of more than $50 million a year in Nevada. This was done primarily through optimal ore movements and consolidation of various functions. During the current period of low gold and copper prices, Newmont has refocused its efforts on efficient operations worldwide. At its mine facilities in Nevada, Newmont has used a combination of several strategies to decrease the costs of operations and to increase profitability. These include computer technology, optimal use of infrastructures, procurement strategies, functional consolidation, enhanced mine planning and several available metallurgical processing options.

Jan 1, 1999

By Richard C. Barth

Fourteen field plots were established at active coal mines in the Northern Great Plains. A wedge was cut into spoil and backfilled with soil; soil depth ranged from 0 to 152 cm over a linear distance of 15 m. Perennial grasses were planted in each plot, and production was measured from 1978 to 1981. Based on spoil traits and biomass response patterns, plots were grouped into four types. Spoil for Type I plots was near neutral, slightly saline, nonsodic, and clay loam in texture. Perennial grasses reached maximum production with approximately 50 cm of soil depth. Spoil for Type II plots was characterized as sodic and fine textured; soil-depth requirements averaged 83 cm for maximum production. Spoil for Type III plots was characterized as strongly acid, and production increased throughout the soil depth range tested. Spoil for Type IV plots was similar to soil in chemical and physical traits; there was no production response to soil depth. Soil depth requirements were also dependent upon precipitation and species. In general, soil-depth requirements decreased in dry years and with use of introduced species. An appendix contains data evaluations on an individual plot basis.

Jan 1, 1982

By Siegmund Babendererde, Jan O. Babendererde

Extruded Concrete Lining combines technological and financial advantages. The tunnel lining is reliably embedded in the surrounding ground as the fluid concrete is extruded at constant pressure directly behind the TBM supporting the exposed surface. Ground deformation from the TBM passage can be compensated and the ground will be pre-stressed by the extrusion process. Developments in concrete technology permit high speed tunneling by use of a slip formwork attached to the TBM. Realised projects in Milano (Italy), Lyon (France), Frankfurt (Germany) and Akima (Japan) will be demonstrated.

Jan 1, 2001

By D. J. Dollhopf

A week-long selective overburden handling dragline op ration was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to hvdrologically isolate a saline overburden zone during placement in the spoil piles. The saline zone had concentrations considered inimical to successful reclamation and was potentially dangerous to future water quality in the spoils aquifer. The zone was identified after review of chemical data for overburden samples collected from the intense 60 m grid drilling pattern. The saline zone in the overburden was: 1) handled in a normal manner; 2) segregated and buried; and 3) segregated, buried, and covered with a relatively impermeable 1.0 m thick clay cap. The method used to formulate this demonstration, the demonstration itself, and the monitoring and evaluation techniques are described in this report. Observation wells were installed to monitor ground water in the overburden, Rosebud coal, and McKay coal. Data from these wells were, used to estimate post reclamation water levels and to evaluate recharge and water movement characteristics in the vicinity of the demonstrations. The inimical zone was successfully handled in a selective manner with a minimum of delays. Economic analysis indicated cost of these selective burial operations to be about 1.1 to 1.5 times the cost of the normal operation at this particular mine site. Long term monitoring will be required to evaluate the effectiveness of these handling techniques in hydrologically isolating undesirable overburden materials.

Jan 1, 1977

By P. Foster, A. Burton

Over the past decade there has been a great deal of research into the use of virtual reality (VR) and computer graphics in the mining industry. Much of this has led to developed applications including training simulators and accident re-construction. One other area where there is considerable potential for virtual reality is that of mining ergonomics. This paper identifies those common ergonomic limitations associated with mining equipment that can be effectively modelled using VR techniques. From this, two simple models have been developed namely (i)remote control continuous miner operation and (ii) free steered vehicle sightlines, which demonstrate the practical use of VR in this area.

Jan 1, 2003

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

The structural design of a mine haul road involves the determination of cover thickness requirements above the in-situ or sub-grade material. The specification of these layerworks is a critical component in the overall road design process. Poor design often leads to premature failure of the road, safety is often compromised and productivity and equipment service-life will certainly decrease. Historically, the California Bearing Ratio (CBR) cover-curve design method has been widely applied to the structural design of mine haul roads. More recently, established mechanistic design principles have superceded the CBR approach to haul road design, using a multi-layer model to represent the various road structural layers. The structural design and associated layer thickness requirements are then determined following a maximum strain criterion. This paper develops a case-study evaluation of the CBR cover-curve and mechanistic design methodologies and through a comparative analysis of layerworks and materials, highlights how improved structural design can be achieved mechanistically.

Jan 1, 2011

By E. Amini

"While methods exist to allow the simulation and optimization of existing flotation operations, there is a deficit in the ability to predict the performance of a new ore type pre-processing. A laboratory scale batch flotation testing methodology has been developed to assess the flotation potential of ores (known as the JK Floatability Index or JKFI). Previous work conducted by Alexander and Collins (2008) showed that the test could be used to predict full scale results in base metal ores. In this work, JKFI tests were applied to three different types of ore and one blend from a greenfields gold deposit to show the test applicability to flotation of precious metals. The results from the JKFI test on one ore type were then used to predict the response of all ore types (including the blend). To validate the predicted kinetic parameters, a comprehensive survey was performed on a pilot plant where each of ore types was processed in the circuit. An acceptable agreement was found between the experimental recoveries and predicted recoveries which indicate the potential of this method for use in predicting the flotation response of an ore.INTRODUCTIONOver 100 years, flotation has been considered an efficient method to concentrate different types of sulphide and oxide minerals and coal. Thus, numerous research studies have been undertaken to find an appropriate model to predict the behaviour of particles in flotation circuits (Barnwal et. al., 2006; Bascur and Herbst, 1983; Cecile and Villeneuve, 1991; Deng et. al., 1996; Zheng et. al., 2006). Most methods are based on the ore flotation response in an industrial plant which is expensive and time consuming to characterise. It is difficult to reliably predict flotation response for new types of ores in industrial scale plants.The floatability component modelling (FCM) approach, developed within the Australian Minerals Industry Research Association (AMIRA) P9 project, has been used to derive models of operating flotation plants for the purpose of simulation and optimisation (Alexander and Morrison, 1998; Alexander et. al., 2000; Varadi, 2006). This approach has been applied at a large number of operating sites treating a wide variety of ores. The approach requires metallurgical surveys to be undertaken in conjunction with batch flotation tests and cell characterisation. This allows ore and machine parameters to be derived, which are then used in the P9 Flotation Model. The development of a FCM generally requires a large commitment of resources and time. While there has been significant support of this approach in industry, the FCM approach is limited to ores already being processed (Runge, 2004; Wightman, 2006)."

Jan 1, 2009