Search Documents

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high' throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By T. R. Ellis

The vast majority of valuations produced for mineral properties using the net present value method provide an estimate of Investment Value or Use Value. Such an estimate can be a long way from the price that the property would sell at if placed on the market. Indicators from the market need to be used to validate or modify the net present value calculation. The comparable sales and replacement cost approaches used in the appraisal of urban buildings generally fail us in the appraisal of mineral properties. Other methods of sales analysis are introduced. Guidelines for what a minerals appraisal report should contain are presented.

Jan 1, 2000

By Marko Oosthuizen, Charl P. Botha, Lidia Auret, Annelette Malan, Marthie de Leeuw

Flotation performance is affected by upstream disturbances (e.g., mineralogy, water quality, flow rate) and controlled variables (e.g., pulp level and air addition). Process disruptions can lead to undesired conditions, such as pulp overflowing flotation cells (with insignificant/absent froth, and thus no valuable mineral concentration). Early detection and appropriate intervention of pulping events improves concentrator performance. An approach to real time flotation pulping event detection by means of convolutional neural networks is presented, including a case study of the industrial application of this technology on three flotation banks.

Feb 22, 2026

By Manuel Gomez

Primary, low-temperature tars are generally known to alter with time. The effect is believed to occur, in some instances, without the external influence of air, light, or heat. Since one of the processes occurring during extended storage is oxidation, the action of mild oxidation induced by air and heat, in addition to the effect of storage, was studied. The principal effect in aging and oxidation is formation of pitch at the expense of the distillate fraction. The fraction boiling above 270° C. is mainly involved in pitch formation due to storage, whereas all fractions are affected to some degree when tar is heated at 125° C. in the presence of air. If the effects of air are considered, the aromatic and tar-acid fractions seem to be important in pitch formation.

Jan 1, 1956

By G. A. Pinsky, Pickard M. K

"IntroductionTWO METHODS of mucking have been used in sinking C shaft, the five-compartment production shaft of the Yellowknife property of Giant Yellowknife Gold Mines, Limited:(a) Band mucking during the original sinking in 1949 and 1950 (l); and(b) Mechanical mucking with the Cryderman shaft mucker during the recent deepening in 1954.This paper briefly describes the recent deepening and compares the performance figures of the two sinking operations.PlanningProduction planning in 1952 showed that it would be advisable to deepen C shaft in 1954 to provide for three new production levels and the installation of an underground crusher. To complete the required shaft work it would be necessary for a shaft crew to deepen the shaft about 500 feet, to partly excavate three level stations and a crusher station, and to cut a station for the loading pocket. Figure 1, a vertical section of the lower part of the shaft, shows the details of the deepening programme.During the planning period, Giant had a rather small supervisory staff and at the same time was experiencing a heavy labour turnover. As it was obvious that production would suffer if the sinking crew were recruited at the mine, it was decided that the merits of contracting-the shaft sinking to an independent contractor should be investigated."

Jan 1, 1955

By Alistair James, Mo Shahsavari, Leon Botham

The 1889 Johnstown Flood, which killed 2,209 people, was a preventable disaster stemming from systemic decisionmaking failures. This paper applies modern Risk-Informed Decision Making (RIDM) frameworks to analyze the historical context and explore alternative outcomes through hypothetical multiverse scenarios. By reconstructing the risk landscape of the South Fork Dam, we demonstrate how structured hazard identification, risk assessment, and stakeholder communication could have mitigated or prevented the catastrophe. Three counterfactual scenarios—proactive maintenance, community engagement, and regulatory oversight—are evaluated to quantify potential lives saved and economic benefits. The study acknowledges historical barriers, including technological limitations, lack of governance, and socioeconomic disparities, which constrained risk-aware decisions in the 19th century. The analysis draws critical parallels to contemporary engineering challenges, particularly in tailings storage facility (TSF) management, where similar risk blind spots persist. The paper concludes that RIDM is not merely a technical tool but a governance imperative, essential for ethical and sustainable engineering practice. By learning from historical near-misses and failures, the modern engineering community can strengthen resilience and accountability. This work contributes to the growing body of retrospective risk analysis, offering a methodological framework for applying RIDM to historical disasters to inform future safety standards.

Feb 22, 2026

By M. A. D. Azevedo, J. D. Miller, R. Kobler, E. Mutkowska

Up to 3 million tons of automotive shredder residue (ASR) is generated annually in United States. Plastics are the most valuable component of the ASR material making up approximately 25% of the total weight. In order to reuse these plastics, a selective process is required to separate each plastic, with very high purity and favorable economics. One separation technique, which may be able to selectively recover the plastics from ASR, is flotation. The preliminary flotation results have demonstrated that acrylonitrile-butadiene-styrene (ABS) and polycarbonate (PC) can be selectively separated from the model ASR feed, the PC/ABS/PA 66 system, by appropriate control of the surface chemistry.

Jan 1, 2001

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By G. Richards Gwinn

The mineral olivine, though known to mineralogists for many years, was of little commercial value in the United States before 1933. It was first described in 1790 by Johann Gottlieb Werner, who named it "olivine in allusion to its olive-green color. Commercial olivine first attracted attention because of its refractory properties. Further research has developed methods of extracting the magnesia content for the production of various magnesium compounds. Experimental and pilot-plant work also are in progress to make olivine available as a low-cost raw material for the production of magnesium metal.

Jan 1, 1943

By Jan Reimann

Increasing individualization with smaller quantities, growing competition from low-wage countries, and the continuous drive towards digitalization are the challenges that industrial companies in high-wage countries must face. The example of the Flender One gearbox modular system demonstrates how consistent standardization and digitalization are the enablers for AI, and thus already enable new business models and business approaches today.

Feb 22, 2026

By P. Ret, E. Üstiindag, R. Dieckmann, R. Subramanian, S. L. Sass

"Partial reduction reactions in the Ni-AI-O system, starting with the spinel compound NiAI20 4, are used to form metal-ceramic microstructures. By suitable choice of processing parameters, such as reduction temperature, oxygen partial pressure and time, two different morphologies of nearly pure Ni particles, equiaxed and rod-like, form within a ceramic matrix, which is either a-A12O3 or a metastable ""defect spinel"". Electron microscopy studies were performed for microstructural characterization, phase identification and chemical analysis. The fracture toughness of the Ni-AI2O 3 mixture was significantly improved with respect to that of the original spinel phase. The important issues that must be addressed to form useful metal-ceramic microstructures by partial reduction reactions rue discussed. It is shown that cracking at the original spinel grain boundaries, likely due to the large volume changes associated with the reduction reaction, can be avoided by the addition of small amounts of ZrO2• Initial results illustrating effect of ZrO2 on the microsuuctures are presented.IntroductionEngineering materials used in load bearing circumstances, particularly under extreme conditions (e.g. high temperatures or stresses), generally are formulated with complex microsuuctures. Such composite-like materials can possess properties unobtainable by either of the individual constituents. With metal-ceramic composites, for example, a material can be obtained with an optimum combination of the low density and high strength of the ceramic, and the toughness of the metal. For high temperature service, where demanding conditions are often present, for example, inside jet turbine engines, a successful new material must have low density, high Young's modulus as well as good oxidation resistance, strength, fracture toughness, creep and fatigue resistance. The candidates include intermetallic compounds, and metal-ceramic, intermetallic-ceramic and ceramic-ceramic composites."

Jan 1, 1994

By Antonio Nieto, Jesus Castillo

Research and Development (R&D) departments in the mining sector are essential for creating new solutions on productivity, safety, and sustainability. Nevertheless, the selection of R&D projects is complex, often influenced by subjective judgments and uncertainties. This paper explores the application of the Multicriteria Decision Analysis (MCDA) as a structured approach to evaluate and prioritize innovation projects based on various criteria such as safety, cost, environmental impact, and social acceptability. By assigning weights and quantifying criteria, MCDA enhances decision-making transparency and objectivity. This study aims to show a method that facilitates strategic thinking, resource optimization, and stakeholder engagement, ensuring that selected innovations align with the company’s long-term objectives and commitment to responsible mining practices.

Feb 1, 2025

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By David A. Summers, Clark R. Barker, Marian Mazurkiewicz

In May 1975 the U.S. Bureau of Mines contracted with the University of Missouri-Rolla, Rock Mechanics and Explosives Research Center to develop a Hydrominer modification to a longwall shearer unit, wherein the rotating pick-laced drums and connecting gear drives are replaced by a water jet cutting ahead.1 The concept of the water jet cutting head is based on using the high localized energy of the water jets to isolate a slice of coal by cutting a slot under, at the back of, and at the top of the web. The plow blade of the head then advances into the cut and wedges the coal cantilever over onto the conveyor (Fig. 1).

Jan 4, 1978

By G Gosson

An important requirement in every geological quality control program is that the identity and grades of the control samples (duplicates, certified reference materials (CRMs), and blanks) must remain æblindÆ to the analytical laboratory. Once the entity to be controlled is aware of relevant details of the control process, such as the identity of the control samples, the objectivity may be lost and the control may no longer be completely valid. Whereas the blind insertion of field duplicates and coarse blanks can be easily conducted at site, simultaneously with the sampling process, the rest of the control samples should be inserted into the batches during or after sample preparation and prior to assaying, in order to ensure a proper assessment of precision, accuracy and assay contamination, independent of the internal quality control of the laboratory. Such a procedure raises the concern that blind insertion of crushed or pulverised material in sample batches prior to assaying could represent a breach in the chain of custody principle, as samples would have to be temporarily returned to the custody of a non-laboratory person in charge of the insertions. In this seemingly conflict scenario, what should we give up? Do we maintain the strict chain of custody, knowing that the laboratory will be aware of the identity of some of the control samples, or that some duplicates will not be true same-batch duplicates? Do we ignore chain of custody issues to maintain the anonymity of the control samples and insert blind same-batch duplicates, CRMs and blanks? Is it possible to do blind insertions without breaching the chain of custody? Current NI 43-101 and JORC requirements, as well as real-world QA/QC and sample security practices, are discussed in light of AMECÆs approach to the solution of this apparent dilemma.

Jan 1, 2008

By J Lea, P Hatherly, J L. Edwards

Coal exploration has traditionally involved the acquisition of data to enable a resource to be quantified and qualified to the extent that its economic potential can be determined. This process commonly relied on: drilling to determine the depth and thickness of coal seams, broad characterisation of the overburden and interburden, and to provide cores for coal quality analyses; basic wireline logging to cross-check the depth and thickness of coal seams and provide some indication of rock mass strength; and basic surface geophysics and remote sensing to identify major geological structures. In recent years, the adoption of the JORC Code as a basis for the reporting of resources and reserves has placed a greater emphasis on the need for detailed, reproducible data sets that not only satisfy the traditional requirements of mine planners, but also satisfy the governance requirements of corporate and financial institutions. Similarly, the development of sophisticated numerical modelling techniques for use in both open cut and underground mine design, has seen a greater demand for precise geotechnical data, in situ stress characterisation and hydrological information as routine input to the design process. These requirements, coupled with the prevailing trend toward high capital, relatively inflexible mining techniques less tolerant of geological surprises, and the need for consideration of environmental issues such as groundwater impacts and surface subsidence, requires that modern exploration programs be multifaceted, and designed to commence capturing data relevant to ædownstream issuesÆ even during the initial phases of exploration planning.

Jan 1, 2009

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

All of the coal resource in North Dakota is lignite. The lignite fields of North Dakota cover approximately 40 percent of the total area of the state, with reserves estimated to be 9.8 billion tons, two percent of the U.S. base. The first commercial coal mine in North Dakota opened in Morton County in 1873. As the railroads crossed the plains, the demand for coal increased. Coal for fuel was supplied by the state's underground mines. By 1884, North Dakota's lignite production had reached 35,000 tons. North Dakota was among the fist states to shift from underground to large-scale commercial surface coal mining. By 1927,40 percent of the total production was by surface mining, compared to 2 percent for the nation as a whole. By 1959,86 percent of the total production was by surface mining, while the national average was 22 percent. Since 1966, surface mining has been the exclusive coal production method in North Dakota. North Dakota's regulatory program received conditional approval December 15, 1980. Following approval of amendments to the program, it received full approval February 18, 1986. The Abandoned Mine Lands Program was approved December 23,1981.

Jan 1, 1992