Search Documents

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By Jeremy Bosman, Niel Lourens

"Cyclones are used in four main applications in primary wet heavy mineral processing plants i.e. upfront desliming, densifying, and concentrate stacking and tails deposition.UPFRONT DESLIMINGMany heavy mineral ore bodies are associated with high slimes varying from 15 to 60%. The increased viscosities arising from the slimes impact negatively on heavy mineral recovery in the spiral plant. Recoveries can be reduced by up to 10%. Cyclones have proven to be able to remove slime efficiently with acceptable loss of valuable heavy mineral in the overflow. For low slime applications, typically below 25%, it is possible to achieve the desired results using a single stage of cyclones, whilst for higher slimes, two stages of cyclones are required. The overflow of the primary stage is retreated through a second stage to minimize heavy mineral loss."

Jan 1, 2003

By Christopher Davey, Marian Mazurkiewicz, Yvonne Spooner, Dana Hankey, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of submicron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill's chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydrowedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By M. Wright, A. H. Mwale

Opportunities to promote enhanced eco-efficiency (i.e. the simultaneous improvement in economic and environmental performance) for the minerals industry exist across the whole value chain. However, given the current operational models of major companies within the industry, and their focus on refining of primary ore bodies, it is important to understand where such opportunities might lie within minerals beneficiation, as it is here that major environmental pressures are felt. This paper examines the combination of unit technologies in a minerals beneficiation train, and explores the inter-relationship between energy input and water consumption for a given mineralogy and product recovery, as these are two critical environmental issues which affect the overall viability of many minerals plants. In particular, we review constitutive relationships for each of the sub-processes of comminution, flotation, and tailings dewatering, and suggest how these might be integrated into a unified hybrid model, with particle size distribution as the key design variable. Such a model can then be used to explore the trade-offs between different performance objectives (be these technical, economic or environmental) as part of a multiple-objectives optimisation exercise. In this way, it may become practical to envision situations in which concentrate grade and recovery are sacrificed, marginally, in order to reduce energy demand in comminution, and improve overall water recovery. In addition, this work provides a useful baseline against which to analyse the potential for dry processing. This becomes more relevant as the industry commits to advancing the sustainable development agenda in the face of the increasing life -cycle costs and impacts of minerals processing operations, coupled to declining ore body grades, and the desire to maximise recovery of minor and trace elements. Some specific observations for copper are offered, supported by operational data from Zambian copper mines.

Jan 1, 2003

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003

By Kazimierz St. Sztaba

"Mineral processing – the first technological stage of utilization of mineral – has a very long history. In particular, it revealed and reveals the continuous development and perfection of technological operations and process organization, comprising not only new design solutions and exploitation procedures but also, for example, perfected systems of control and automation as well as methods of process description and result evaluation. During the recent decades the attitude to mineral raw materials was clearly changed, both to the primary ones, i.e. minerals, and to the secondary ones, such as side products and waste, formerly considered useless and at present more commonly used. This results both from the appearance and growth of demand for more and more numerous components of mineral raw materials and also from the necessity of protection of natural resources, constituting the integral part of the system of sustained development of society.These circumstances, and especially the requirements concerning gaining some components which cannot be separated by means of “classical” (used for many years) technological processing operations and aiming at increasing the technological procedures, evoked the necessity of using new technological solutions, applying other basic operations, also the ones characteristic so far for other processing technologies, i.e. chemical, biotechnological and others.These development tendencies, in general commonly perceived, allow us to formulate an opinion that the former state of tasks and processes of mineral processing is being transformed into a qualitatively new form. It can be assumed that this process was signaled by a situation in which, due to the growing role of technological operations based on physicochemical phenomena (flotation and others), magnetic and electrical ones, etc., one should have observed that the former term of “mechanical processing” became inadequate for the real content of the notion determining the discussed stage of mineral utilization, so the adjective “mechanical” disappeared in most languages."

Jan 1, 2003

By B. C. Qi

"In water treatment, flocculation or coagulation with aluminium or ferric salts has been widely used for many years to remove natural organic matter (NOM), including humic acids. However, the adsorption of NOM to aluminium hydroxide flocs during conventional coagulation/flocculation processes is very complex, with the flocculation of aluminium hydroxide particles and the adsorption of NOM molecules on flocs occurring simultaneously. Any effect on the surface characteristics and micro-structures of the humic acids and aluminium hydroxides could affect the adsorption efficiency.It has been widely observed that if a reaction system (liquid-liquid or liquid-solid) is exposed to an ultrasound field, under appropriate conditions, a variety of physical (emulsification, aggregation/flocculation) or chemical (the production of radical and exited species; single electrotransfer) actions may be activated. Though the ultrasound effects have been used in biological and chemical decontamination in many conventional environmental protection practices, the idea to explore the ultrasound effects in the removal of humic acids by preformed aluminium hydroxide flocs is relatively new. In this paper, the effect of an in-situ ultrasonication on removal of the humic acids extracted from the acidification fermentation of lignocellulosic residues, by a preformed aluminium hydroxide, was evaluated; the effect of ultrasonication on the surface complexation of the humic acids with the preformed aluminium hydroxides was investigated."

Jan 1, 2003

By Konstantin Fedotov, Victor Beloborodov, Anatoly Potyomkin

"There are areas in Russia, which cover huge territories and they are north, and Siberia. These difficult to access regions with cold climate are rich in a great number of distant deposits of valuable and rare metals, gold and platinum. The development of such deposits requires highly effective technologies of mineral processing which could be realized in modular and quick-built processing plants.The work presented includes the results of long term research in the development of new technologies of processing of zirconium (in the form of rare mineral Baddeleyite – natural zirconium dioxide) bearing ore of the Kovdor deposit which is located in the Polar region of the Kola peninsular and also in Siberia deposits of of ledge ores of gold."

Jan 1, 2003

By Victor Avdokhin, lvan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation."

Jan 1, 2003

By Jochen Petersen, Harro von Blottnitz

"The landfill disposal of slags is common practice in the metallurgical industry. Chromium may be a minor constituent in many cases. It is present mostly in the form of chromites, which are considered environmentally benign and hence safe for disposal. Wastewaters from metal finishing operations are most commonly treated by reduction and precipitation of dissolved metals, including chromium, by lime addition, and subsequent landfill disposal of the resulting sludge. The metals contained in such sludges are mostly in the form of hydroxides, and as such considered environmentally stable.Thermodynamically, trivalent chromium, which is the predominant form in these waste materials, can be oxidised to the hexavalent form by atmospheric oxygen. Detailed research work on both slags and sludges has shown that a gradual emergence of hexavalent chromium can indeed be observed. The mechanism is governed by close physical contact between chromium oxide (or hydroxide) phases on the one side and calcium oxide (or hydroxide), which is present as flux in slags and residual lime in sludges, on the other. If oxygen can migrate to the points of contact, gradual formation of calcium chromate ensues.Hexavalent chromium is associated with high environmental toxicity, and hence undesirable in landfilled materials. Moisture migrating through landfill deposits can mobilise the highly soluble chromates and thus potentially transport them into natural waterways. Such gradual release from stainless steel and ferrochromium slag deposits has been demonstrated in a column experiment."

Jan 1, 2003

By Carin Laubscher, Francis W. Petersen, Jaap P. Smit

"Waste streams, such as acid mine drainage, are often characterised by low pH values and high concentrations of heavy metals, dissolved solids, calcium and sulphates. Although lime remediation effectively removes most of the heavy metals as hydroxides, it is less effective at lowering levels of sulphates. Various methods of removing sulphates from effluents exist, such as precipitation with lime, precipitation with barium salts, co-precipitation with calcium carbonate, reverse osmosis, and ion exchange. Mintek developed a chemical precipitation (SAVMIN) process to treat acid mine drainage, which entails the addition of lime to precipitate the metal hydroxides, and the subsequent formation (precipitation) of calcium sulphoaluminate or ettringite. The key to the viability of the new technology lies in the correct use, regeneration and recycling of Al(OH)3 used to precipitate the ettringite. The water produced by this process is suitable for disposal to watercourses or for agricultural, domestic or industrial consumption. No brines are produced as the salts are converted to solid hydroxides, gypsum and calcium carbonate.The SAVMIN process has been tested successfully during several laboratory scale operations, and during two pilot plant operations at Stilfontein Goldmine for Anglogold and Navigation Plant, Witbank for Anglocoal. During the pilot plant campaign at Navigation Plant, metal and mineral precipitation was achieved with lime addition. The sulphate concentration in the water was reduced from 2136 mg/L to an average value of 102 mg/L and the calcium concentration was reduced from 727 mg/L to an average value of 70mg/L.The SAVMIN process generates a number of different waste streams including metal hydroxide sludge from neutralisation, gypsum sludge from the gypsum crystallisation steps, and calcite sludge from carbonation. The metal hydroxide sludge is composed of Mg, Ca, Mn and Fe hydroxide, and could be disposed of on a slimes dam. Gypsum sludge was greater than 99% CaSO4.2H2O. This gypsum could be used for dump or road capping, underground backfilling, production of wallboard and cement. The calcite sludge is pure CaCO3, which is recycled back to the neutralisation stage."

Jan 1, 2003

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

"The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation are just a few of the processes that are largely influenced by the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the importance of surface wettability, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In the present study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.Through the use of an inert adhesive and an inert macroscopic surface as a support, it is illustrated that precise measurements of particle wettability are obtainable under suboptimal or ‘shop floor’ conditions. The measurement of the maximum external meniscus height formed between a test liquid and a particlecoated rod is employed to estimate phenomenological contact angles on particles ranging form a few nanometers to several hundred microns in size."

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By F Battaglia-Brunet, D. H. Morin, Foucher S. ’

In the mineral-processing field, bioleaching of metal sulphide concentrates is currently operated in very large mechanically agitated tanks. Such bioreactors have considerable requirements in terms of power consumption for mixing, aeration and heat transfer. The use of slurry bubble column, where the particles are suspended by gas motion as well as by liquid upward flow, could be an alternative to achieve bioleaching in more economical conditions. In order to compare these two techniques, a unit of stirred reactors in cascade and a bubble column were comparatively operated at laboratory scale in the bioleaching of a pyrite concentrate. For both pieces of equipment, experiments were performed not only in batch mode but also in continuous conditions.

Jan 1, 2003

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By Chris A. Bennett, Glenn S. Dobby, David A. Bulled

Establishing reagent dosing strategies for new ore bodies has traditionally involved a combination of experience and empirical experimentation using standard laboratory tests. The grade and recovery data resulting from these lab tests have historically been used as direct indicators of plant performance despite the obvious differences between the flotation environments. A reagent scheme selected in this way would subsequently be employed to generate the grade and recovery information for the geometallurgical model which in turn was used for metal production and cash flow forecasts. If the reagent scheme was sub-optimal then so too would be the forecasts and the resulting cash flow.

Jan 1, 2003

By Dominic Howarth, Diana Drinkwater, Don McKee

At a time when the mining and minerals industry across the world is undergoing unprecedented change, the very fabric of the tertiary education system which is the principal source of trained professionals to the industry is in decline in many countries. The change sweeping the industry is globalisation as evidenced by the emergence of a relatively small number of increasingly dominant corporations with operations in most of the major mining countries. The education sector is struggling to provide sufficient graduates as the viability of small mining schools declines. That is only part of the problem as the global operating industry is increasingly seeking graduates who are comfortable working in different countries and cultures. One obvious response to the industry needs and developments is for the education sector to consider how it can best respond to the global opportunities. This paper presents the case for a global education network which is based on a network of international thinking Universities and which makes use of the latest in educational thinking and technologies to provide a quality education and in the process produce graduates fitted for international careers.

Jan 1, 2003

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By T. R. Ellis

Australia’s mineral valuation code continues to evolve, while mineral valuation standards are also being written for Canada and Southern Africa. The author is leading a task force for writing the extractive industries addition to the International Valuation Standards. Meanwhile, the International Accounting Standards Board is continuing the development of an extractive industries addition to its International Financial Reporting Standards, with an emphasis on valuation reporting. This paper analyzes the need, content and ownership for a U.S. minerals appraisal standard in the context of both these developing international standards and also existing U.S. regulations and appraisal standards. The author provides many questions for research and debate.

Jan 1, 2003