Search Documents

By Axel Preusse

Due to a political decision, German hard coal mining will come to an end in the year 2018. By then, there will have been more than 150 years of industrial grade mining activities. Located in the western part of Germany is one of the most densely populated areas of Europe. Multiple coal seams have embossed the earth?s surface up to 20 meters (21.87 yards), as mining has subsided. The aftercare of hard coal mining will consist of three tasks: groundwater management, polder management, and groundwater treatment. The Ewigkeitslasten (cost in perpetuity) at the current groundwater level has been determined in the past. The actual cash value is calculated to be about 12.4 billion euros (approximately 16.5 billion dollars). The cost of groundwater management is directly related to the groundwater level. Rising groundwater levels will reduce the cost of pumping water. Known effects of rising groundwater are uplift of the surface, emission of methane gas at the surface, higher risk of cave-ins, and contamination of drinking water horizons. Each of those processes produces cost in order to prevent negative consequences (e.g., uncontrolled methane emissions) or to handle reparations (e.g., damages caused by surface uplifts). In the long run, it is the goal to minimize the Ewigkeitslast. As a first step, all cost-generating processes are specified, and a cost type based characterization is performed. The objective of this case study is to identify key parameters to determine the quality of a cost-generating process (proportional cost, fixed amount cost). Afterwards, it is intended to specify the quantitative impacts of each parameter and to set up an optimization model to minimize the overall cost. The quantitatively specified parameters will form the base out of which the optimization model is created.

Jan 1, 2013

By C. J. Wilhelm, John M. Devine, Ludwig Schmidt

"Steel tanks often corrode rapidly in oil fields where the Gas produced with crude contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion.Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no carious corrosive action. These uses indicated that aluminum tanks,be equally effective in counter- acting hydrogen sulphide corrosion. Consequently, in the spring of 1920, an all-aluminum stock tank of 500 barrels capacity and a ""composite"" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co, in Crane County, Tex. These tanks were under observation for one year, the toot being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Reel Co. The results of this preliminary test sustained the belief that aluminum is highly resistance to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the quantities o highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the aluminum Co. that additional tests be made to include production conditions in large quantities of brine would be handled, for pact experience had shown that aluminum often is susceptible to the corrosive action of brines."

Apr 1, 1931

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

By E. G. Dahlgren, Dan O. Howard

THE West Edmond oil field, which covers parts of Oklahoma, Canadian, Kingfisher, and Logan Counties in the State of Oklahoma, is in geographical extent the largest single oil field found in the state. At the present time, its area of 26,800 acres is almost twice as large as the Oklahoma City field, which hitherto was the state's largest field. Many authorities believe that the West Edmond field is the most important oil pool found in the United States since Pearl Harbor. The discovery of the field without the help of geological, geophysical, or other recognized technical information, the fact that the oil and gas accumulated in a stratigraphic or wedge-type trap, and the rapid development of the productive area under wartime conditions are some of the interesting features of the field. The West Edmond field lies west of the Oklahoma City, Britton, and Edmond fields. The field is in an area that has been considered on the west flank of the Granite Ridge line of folding, on which a number of Central Oklahoma's most important oil fields are located. Over a period of years, especially since the discovery of the new pools such as Oklahoma City, Edmond, Britton, and Crescent, the general area of the West Edmond field has been explored intensively by geological and geophysical methods. This led at times to the drilling of a few dry Wilcox sand tests.

Jan 1, 1945

By L. F. Reinartz

ANOTHER year has rolled by. We are twelve months further away from the start of the depression and. therefore that much nearer to recovery. The accumulated needs and wants 'of our lame, virile population are ready to burst their bonds as soon as confidence returns and credit is stabilized. The steel industry has been harassed by uncertainty of the Government's attitude toward organized labor's de¬mands, and irregularity in volume of production. Steel labor, if left to its own devices, would in most instances, march shoulder to shoulder with the management of steel plants in their effort to pull the industry nut of the ?red.? Cooperation between management and men has improved considerably during; the year.

Jan 1, 1935

By A. A. Campoli

The U. S Bureau of Mines is conducting research to develop improved guidelines for selecting the type and pattern of roof support in different geologic environments (Mucho, et al., 1995). As a part of this wider research effort, a multifaceted ground control investigation was conducted at the Diamond TB Mine of RoxCoal, Inc. The study included statistical analysis of mine-wide roof bolt performance, instrumented bolt test areas, stress damage mapping, and pillar design analysis. The mine employs state-of-the-art continuous miner technology, including mobile roof supports and continuous haulage, to retreat mine the Lower Kittanning Coalbed. A herringbone section design makes the stability of the center belt entry critical to efficient retreat mining. Roof cutters formed during section development sometimes set up unstable immediate roof conditions in advance of the belt entry mobile roof supports during retreat mining.

Jan 1, 1996

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

By R. J. R. Schaller

NO. 3 winze, the sixth shaft to be sunk on the San Antonio property, is practically a duplicate of No. 3 shaft, which was the main shaft prior to the installation of the larger hoisting equipment in 1939. It is collared on the tenth, or 1,500-ft., level, and goes down vertically to the sixteenth, or 2,500-ft., level, with a loading pocket, spill pocket, and sump below this. It is 1,000 feet east of No. 3 shaft. All ore, men, and materials are handled through the latter. The winze location with reference to the rock formation is shown in Figure 1. (In plan, this section strikes N.30°E. and cuts most of the main orebodies of the mine normal to their strike.) It is collared eighty feet inside the footwall contact of the basalt and cuts through it before reaching the eleventh level. In this location there will be no ore tied up in shaft pillars, as the closest ore to the shaft is on the tenth level, and here it is eighty feet northeast of the collar. The winze headframe and hoist-room straddle the main haulage to the No. 3 shaft, on the tenth level (see Figure 2). At no time during the excavation for the headframe and hoist-room was the general routine work of this haulage held up.

Jan 1, 1941

By J. Wills

The use of drilling rigs to increasingly mechanize stope drilling has been acknowledged as important for the S.A. mining industry in it ís efforts to tackle the challenges of low productivity, AIDS and an ageing driller workforce. The spin-offs of increased safety, cost-effectiveness and better mining performance provide advantages to all?from the driller to the shareholder. However, implementation or product rollout has varied from outright success to dismal failure. A study of various cases by Novatek and Anglogold TDS showed clear reasons for these differences. Whereas the successes were characterized by clear objectives, accountability, user buy-in, a commitment to make the technology work and no-nonsense reporting, these were typically absent in failed implementations. The attitude at unsuccessful mines was to ?trial? the equipment?even subconsciously, a ?trial? is a test where failure becomes an acceptable outcome. During the study it became clear that mining management are not adequately trained to manage the often-tricky rollout process. They are often also not empowered or clearly mandated to deal with the organizational, human and technical issues that must dovetail to create a success. The output of the study was to develop a basic rollout process that could be used to formally manage the implementation of new drilling technology. Creating an alignment between the mine, workforce and supplier promotes a win-win situation that will not otherwise spontaneously arise.

Jan 1, 2002

By D. Swanson

Cold Detonation Physics (CDP) is a patented new field of explosives and the name for the explosive that is produced when non-toxic dry ice (frozen carbon dioxide) is combined with powdered metals such as magnesium and aluminum, which are non-toxic and nitrogen-free. The explosive is detonator-sensitive and detonates according to the rapid reduction of carbon dioxide back to carbon, which produces solids comprised mainly of metal oxides and about 5% carbon. CDP was determined to produce a maximum of 300 liters of carbon dioxide per kilogram (4.81 ft3 /lb) and about 1.5 liters of carbon monoxide per kilogram (0.024 ft3 /lb). Both these figures shift according to metal content where higher metal produces less gases. According to theoretical modelling, the relationship between static pressure and metal content was determined to be an inverse parabolic curve with optimum pressure at 25% to 31% metal, depending on the type/s of metal/s used. Velocity of Detonation (VOD) was determined by measuring light at the wavefront with fiber-optic cable inserted into a series of holes drilled into the side of a 3-inch diameter (76 mm) schedule 40 steel pipe containing the mixture. The highest VOD was observed at 25% magnesium and measured between 2,500 to 4,500 m/s (8202 to 14,764 ft/s) when initiated by a 454-gram (1-pound) booster and an electric detonator. A 25% 50:50 alloy of magnesium and aluminum sample shot at a higher velocity than magnesium, according to how the alloy generated smaller pieces of shrapnel when compared with shrapnel from a magnesium test. CDP, using 25% alloy, was tested for blasting limestone by drilling 3.5-inch holes (89 mm) and inserting a 3-inch x 4-foot cardboard tube (76 mm x 1.22 m) with the mixture, packed to a density of 0.62 g/cm3 . The blast was initiated with an electric detonator, behaved like ANFO with more energy and fractured rock sufficiently across the entire length of the borehole. Seismic analysis determined that CDP produces lower ground vibrations than traditional explosives.

Jan 1, 2024

By Martin Berman

Tables of 28 positions for all the transitions for nine common analyzing crystals for first, second, and third order reflections were compiled by the Bureau of Mines to facilitate elemental X-ray fluorescence analysis on multi-element systems. The tables are based on a compatible set of wavelengths for 2,346 observed X-ray transitions of the elements lithium to americium. The results are tabulated in order of increasing wavelength as well as by increasing wavelength for each element.

Jan 1, 1969

By Ryan Weaver, Travis Coleman

The drilled shafts that support transmission lines and substations have been increasingly subject to testing to assess the integrity of placed concrete. Cross-hole Sonic Logging (CSL) has been used, but large diameter shafts with challenging site access are generally more favorable to Thermal Integrity Profiling (TIP) testing. TIP testing assesses the shafts based on measurements of the concrete temperature during curing. The TIP results provide assessment of integrity both within and outside the cage, along with information about the alignment of the cage and concrete cover. This data has allowed shafts with imperfect results to be subject to more detailed structural evaluations. However, it may not be well understood how to use this additional information by designers and engineers. The purpose of this paper is to present TIP results of transmission line foundations, both with and without issues with integrity, including cage shifting, minimal concrete cover, or soil inclusions. The intent is to provide general guidelines of the issues that merit additional investigation and those that should be recognized as inconsistencies inherent to underground construction. BACKGROUND This paper is intended to discuss some of the drilled shaft evaluations made when TIP testing is performed. The authors of this paper were recently involved with a transmission line project that was designed and constructed for a Confidential Utility Client located in the Midwest United States. The project was delivered as an Engineering, Procurement, and Construction (EPC) contract with the electrical line construction company as the prime contractor. The contractor then subcontracted several parts of the work which included engineering for transmission line and foundation design, foundation construction, and third-party testing intended to evaluate the concrete homogeneity and integrity of the place concrete in the deep foundations. The testing method selected was Thermal Integrity Profiling Method B, which uses thermal sensors embedded in the concrete. The TIP testing was administered by Mr. Travis Coleman with GRL Engineers, Inc. Mr. Ryan Weaver with Burns & McDonnell served as the owner’s engineer and technical consultant for the utility and was responsible for reviewing submitted TIP reports and providing recommendations to the utility on their acceptance, and if there were any issues that would warrant further discussion and analysis.

Jan 1, 2019

By R. A. Spitz, R. Leiby, M. Bricker

Electrochemistry plays a significant role in minimizing wastes at East Penn's secondary lead smelter. East Penn has been recovering spent battery acid for reuse in new batteries since 1992. East Penn also produces a fertilizer feedstock from sulfur dioxide in the smelter stack gases. The success of these processes is, in large part, due to the installation of electrochemical cells. The cells in the acid recovery plant allow the waste from this process to be concentrated into less that 10% of the original spent acid. The cells in the fertilizer plant treat the solution to remove dissolved metals prior to sale to fertilizer manufacturers.

Jan 1, 2000

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Joseph C. Buchen

IN principle, production of salt from sea water is a simple operation. Sea water is trapped in ponds, the sun and wind cause evaporation of the water, and what is left is principally salt. Commercial production of solar salt, however, requires a careful consideration of many factors. Obviously, sufficient evaporation must take place throughout the making season to produce an economically adequate crop. Other factors are density of soil, contour of ground, height of ground above sea level, minimum dilution from fresh-water streams, and distance from market. Unfortunately, in the United States the localities of greatest evaporation, allowing for the other factors, are not the most suitable for the manufacture of sea salt by solar evaporation. The south end of San Francisco Bay most

Jan 1, 1937

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961