Search Documents

By S. Steinlechner, G. Schneeberger, J. Antrekowitsch

The recycling of steel mill dusts is getting more and more important. The costs and requirements of land filling are rising and companies are interested in new recycling strategies. The rising of sustaina¬bility hand in hand with the high rate of valuable metals in these residues supports new research activities on the recycling sector. Especially zinc but also iron and lead are economical factors due to the treatment of steel mill dusts. This paper gives a small overview of fundamental studies concerning the chemical and physical composition of these dusts. Furthermore aggregates for the reduction of these dusts in the liquid phase are introduced and compared. The Flash-Reactor, the TBRC-Technology (Top Blown Rotary Converter) and submerged arc furnaces and there use for melting and treatment of these dusts are in the center of interest of this paper. The final conclusion gives an overview of possibilities for reduction of filter dusts in the liquid phase.

Jan 1, 2011

By A. F. Silva, J. M. G. Sotomayor, V. F. N. Torres

Geotechnical monitoring plays an important role in the detection of operational safety issues in the slopes of open pits. Currently, monitoring companies offer several solutions involving robust technologies that boast highly reliable data and the ability to control risky conditions. The monitoring data must be processed and analysed so as to allow the results to be used for several purposes, thereby providing information that can be used to manage operational actions and optimize mining plans or engineering projects. In this work we analysed monitoring data (pore pressure and displacement) and its correlation with the tension and displacement of the mass of an established failure slope calculated using the finite element method. To optimize the back-analysis, a Python language routine was developed using input data (point coordinates, parameter matrix, and critical section) to use software with the rock mass parameters (cohesion, friction angle, Young’s modulus, and Poisson’s ratio). For the back-analysis, the Mohr-Coulomb criterion was applied with the shear strength reduction technique to obtain the strength reduction factor. The results were consistent with both the measured displacements and the maximum deformation contours, revealing the possible failure mechanism, allowing the strength parameters to be calibrated according to the slope failure conditions, and providing information about the contribution of each variable (parameter) to the slope failure in the study area.

Oct 1, 2021

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By Güney

"An investigation carried out to determine the tendency of coals to heat spontaneously in terms of time-temperature curves coupled with the resulting oxidation products in an adiabatically controlled laboratory setup is described. Tests were made at differing moisture conditions, including oxidation and also oxidation with either adsorption or desorption of water vapour on coal.From the experimental evidence, there is reason to believe that the oxidation of coal, although an important factor, is not the predominant one in the development of spontaneous heating. In addition to the temperature increase in coal and the gaseous products evolved due to auto-oxidation, the process is accelerated by adsorption and retarded by desorption of water vapour on coal."

Jan 1, 1971

By Christopher J. Bise

Volume II of this collection of research reports, entitled "Model Training Program," provides the framework and details for developing a tailored training program for a specific mine based upon documented human-performance deficiencies. To do this, several steps must be followed prior to program implementation: 1) background information must be gathered (database analysis), 2) direct observation of indicated problem areas should be conducted (safety sampling), and 3) separation of those deficiencies to be addressed through training from those which would be better addressed by workplace or equipment redesign (trainability assessment). Once training is determined to be the appropriate strategy for addressing the noted deficiencies, several approaches can be taken, depending upon whether the problem is related to repetitive work procedures in a predictable, a variable, or a dynamic workplace with a substantial amount of interaction between workers, equipment, and the environment. Although this volume and the subsequent seven volumes provide examples of how the training information was field tested using various strategies (for example, loss control, task training, etc.) and techniques (for example, microcomputer-based exercises, lectures, etc.), the ultimate selection of the delivery method is based on cost/benefit analysis. Therefore, the Model Training Program has incorporated a Training Cost Model as a desirable component.

Jan 1, 1993

By E. Isokangas

The production of minerals for economic use is a two-stage process, involving mining to extract the mineral from the ground, and processing to convert the mineral into a marketable product. Generally, mining and processing have been viewed as self-contained entities. Both have separate objectives, separate cost centres and key performance indicators (KPIs) that do not reflect the customer/supplier relationships that inherently exist. However, mining and processing operations are inter-connected and therefore intimately inter-related with the performance of one operation affecting the performance of another. Optimizing each stage separately without considering the whole system often misses potential economic benefits and energy savings. During the past fifteen years, the authors have been involved in implementing a holistic methodology ?Mine to Mill Process Integration and Optimisation (Mine to Mill PIO)? to maximize the overall profitability of the operation rather than just optimizing any individual process in a mining operation. Metso Process Technology and Innovation (PTI), along with their project partners, have conducted several projects to significantly increase their production- generating typically 5% to 20% higher throughput and improve the overall mine and concentrator performance through PIO methodology. This proven methodology has applications ranging from greenfield projects to long-standing operations with AG/SAG, HPGR or conventional grinding circuits. This paper explains the Mine to Mill PIO methodology and discusses the benefits of such an approach on the energy consumption, the overall costs and benefits of mining operations. The paper also summarizes several case studies illustrating the use of PTI methodology in a variety of applications. Keywords: integration, optimization, simulation, modeling, mine-to-mill, comminution, blast, drill, crushing, grinding

Sep 1, 2012

By A. Vorster

The objective with mine planning is to consistently deliver production conforming to quality and quantity requirements throughout the life of the mine. The complexity of the operational context of the modern mine extends far beyond the actual production actions and there is a need to find ways of analysing and managing this extended environment. A well-established approach to handling complex situations rely on the creation of representative models that use classification and visualization strategies. An example of the use of a classification scheme is the periodic table of the elements. All physical matter can be expressed as combinations of basic elements. Not only is the periodic table useful in classifying and identifying matter but it can also be used for the prediction of the properties of unknown matter and compositions of elements.

Jan 1, 2001

By T Baumgartl, D Mulligan, R Haymont

Mining at the Mt Leyshon Gold Mine in semi-arid north Queensland stopped in 2002. Newmont Australia has recently initiated a thorough post-closure water management study of the site by revisiting the existing information and conducting new water-related investigations. The focus of this paper, which is the first publication on post-closure environmental management of the site, is an overview of the site water quality in view of the sources and spatial distribution of polluted mine water, and also the performance of cover systems in controlling water flux though mine wastes. Since the mine closed the rehabilitation of waste rock dumps and tailings dams have significantly improved water quality in the surface receiving waters. However, the Scats Stockpile, the Heap Leach and Old Plant areas, which can potentially produce acidic waters, enriched with heavy metals and arsenic, are the top management priority. Modelling of the potential transport of contaminants in groundwater needs further investigations. A detailed examination of the waters in seepage sumps showed high concentrations of manganese, cobalt, nickel and selenium, which were previously overlooked. The study also showed distinctive chemical signatures for waters at different locations: the waters draining from scats, supergene materials and waste rocks have distinctly lower pH and higher concentrations of dissolved iron, sulfate, heavy metals, Mg, Mn, U, Se and As. While, the tailings sumps are more alkaline, and are enriched in Na and Cl. The southern tailing sump is characteristically As rich. The waters draining from the supergene materials have higher Cu concentrations. Assessment of the cover monitoring systems showed that although covers pass the design criteria, automated recording of data may ignore any failure of the monitoring system. Recalibration of the moisture sensors not only showed realistic moisture values compared to rainfall data but also showed that the permanently installed system records values that are higher than those of the mobile system. Event-driven recording of data overlooks infiltration events. Besides, with a higher time resolution (daily measurements) the breakthroughs could be clearly detected. Modelling of the water balance in covers is underway and an example is given here. Newmont is currently reviewing water management options and is willing to share the lessons learned.

Jan 1, 2006

By I. Yelkin, Erico Tabosa, Alex Jankovic, R. Hayashida, R. Faveere

"The mining industry faces growing challenges from more complex and lower grade deposits, rising costs, limited energy and water availability, and increasing societal pressure to operate more sustainably. Mining operations need to be more efficient, not just to reduce environmental impact, but also to remain economically viable.To maximize profitability and sustainability, existing operations and new projects must consider integration and optimization of all stages of production. A mining operation is essentially a series of inter-connected processes, with the performance and outputs of each stage affecting the subsequent ones. Optimizing stages in isolation can result in sub-optimal overall performance.The industry has long recognized the benefits of holistic optimization using the Mine-to-Mill concept, and there are many well documented successes. However, it is increasingly common to observe operations simply increasing explosive consumption in the mine and expecting optimization of the entire value chain (mining and processing). For true holistic optimization, blast intensity is not necessarily increased, but rather adjusted to best suit the requirements of the different types of ores treated, the circuit configuration and equipment, installed comminution power and the downstream beneficiation processes. It is a fully integrated effort with optimization of many aspects in the mine, comminution and separation processes.To be successful, optimization of the production chain from mine to process requires a site-specific, structured methodology supported by extensive ore characterization, auditing, surveys, data analysis, mathematical modelling simulations and a cost / benefit analysis. Following this methodology, optimization strategies are rapidly identified and implemented considering mine and plant constraints. Management needs to set up appropriate KPIs and site personnel need to be trained for the new operating strategies to be successfully incorporated into site practices and procedures in the production environment. This will ensure the benefits are achieved and maintained. This paper describes the methodology employed by Hatch to improve overall efficiency and profitability from mine to process. Two case study examples at Russian gold operations and benefits achieved are presented."

Jan 1, 2018

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By K. Duckworth

"AbstractA new electromagnetic depth sounding technique was applied to the measurement of salt thickness above the workings in the Central Canada Potash Mine at Colonsay, Saskatchewan. The initial tests indicate that this new technique can measure salt thickness and that the technique possesses operational feature s which make it possible to monitor trends in salt thickness throughout the mine. The technique can be applied using existing equipment, but the tests do indicate the desirability of developing equipment with features specially suited to the mine environment.IntroductionTESTS were conducted in the Central Canada Potash Mine at Colonsay, Saskatchewan during 1974 and 1975 to determine if a new technique in electromagnetic depth sounding could provide a convenient means of measuring salt thickness above the workings. This new technique, which was described by Duckworth (1975), offers operational features which appear to be advantageous in this particular situation.The problem requires that soundings be made upward from the mine workings to the base of the second red shale. This shale forms an impermeable seal on top of the Prairie Evaporite. A knowledge of this salt thickness is of interest due to the need to avoid any possibility of the workings rising to cut the red shale. Another desirable objective is the detection of any disruptions of the red shale. Ideally, this should be done ahead of the workings in order that such areas of disruption may be avoided."

Jan 1, 1977

By Norman Paley, Finn Ouchterlony

Detailed fragmentation data for different blast delay timing tests at the Red Dog mine in Alaska are analyzed. This work is a continuation of previous work in which the crusher output was found to be better described by the three-parameter Swebrec function than by the Rosin-Rammler function. For a crusher model, the x50 variable sufficed to describe changing crusher input while b and xmax could be considered fixed. For the crusher output from aggregated stockpile rock, as measured by digital image analysis using Split-Online, the constancy of b was not as apparent. In this paper detailed stockpile data, single Split data series, and sieved belt cuts of crusher product are analyzed using the Swebrec and truncated Rosin-Rammler functions. The variability of b is confirmed. By using specific fraction passing sizes a shortcut is presented that removes the need to do curve fitting to determine the three Swebrec function parameters.

Jan 1, 2013

By Mehmet Bu daycı, Onuralp Yücel, Ahmet Turan, Murat Alkan

In this study, iron based alloys (Fe, Fe-Cr-Ni-Mo, etc.) were produced by using metallothermic methods starting from Mill Scales obtained continuous casting processes. During the process, the combustion was realized by ignition and the produced wave propagates throughout the reactant mixture yielding the desired product. In this work, Mill scale used as an iron source, which includes +2, +3 values iron oxides. Aluminum, Magnesium and Silicon were used as reductants. In these metallothermic experiments, different ratios of reductants were examined, and their effects on the metal recovery and alloy compositions were investigated. The samples were characterized by using chemical analysis (AAS), XRD and XRF techniques.

Jan 1, 2016

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By J. Gholamnejad

The aim of short-term production scheduling is to decide which blocks of ore and waste to mine in which time period (shift, days, weeks or months) so that several operational and geometrical constraints can be satisfied simultaneously. Since 1960s several mathematical programming approaches were developed for solving production scheduling problems that are based on a combination of various operational research approaches such as linear programming (LP), integer programming (IP), dynamic programming (DP), etc. A number of models have been developed in the past three decades but some models have limited application especially to geometrical mining constraints. One of the geometrical constraints is block accessibility. All blocks must be accessible to mining equipments on the same bench. In this paper a binary integer programming model is developed in order to incorporate block accessibility constraints in an efficient manner. This mathematical model insures that each block has been open and can be loaded and transported easily by shovels and trucks.

Jan 1, 2008

By A. Sadik

The proliferations of media sources and non-profits organizations in Ghana have put the negative impacts of mining on the ?spot?; this has resulted in public outcry about mining. Although, the gold mining industry has responded by implementing several voluntary measures to ensure sustainable mineral development, these critics label such measures as ?green wash?. In this study, a content analysis of newspaper articles of the Ghana Web Database was carried out after the collection of a total of approximately 900 newspaper articles from it. The data were statistically analyzed to chronologically examine the main media view points and the changing perception of mining issues as reported by private and public media. The results showed government, mining industry (Gold), illegal miners and non-profit & community groups as the main media view points and total of twenty-eight related gold mining sustainability issues. The findings of this study could be used by the gold mining companies to improve upon the communications of their unknown sustainable mineral development measures and to design effective communications and education programs for the public.

Jan 1, 2009

Jan 1, 1971

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019