Search Documents

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By D. J. Fourie

During the production of pure TiO2for the pigment industry, ilmenite, containing 35?60% TiO2, is reduced to high titania slag, containing 70?95% ?TiO2? and pig iron. The high titania slag produced, consists mainly of titanium in different oxidation states and FeO in equilibrium with liquid iron. To predict the phase and chemical reaction equilibria in a furnace, a suitable solution model is required with accurately determined binary interaction parameters, as slag melts tend to behave very non-ideally. This paper investigates two popular slag models, namely, modified quasi-Chemical (MQC) model and the cell model and provides the binary interaction parameters based on recently published data of the ternary system and critically assessed published unary and binary data. Very few modelling results have been published on the ternary Ti-Fe-O system pertaining to high titanium slags. The solution models, with their regressed interaction parameters, can subsequently be implemented in commercial software of the slag-metal phase equilibria to predict how much and which type of solids will precipitate for a given bulk slag chemistry and operating temperature or, alternatively, above which temperature should a furnace be operated to avoid excessive solids precipitation.

Jan 1, 2005

By W. E. Anable

The Bureau of Mines researched methods for recovering copper from cyclone and electrostatic-precipitator dusts of primary copper smelters as part of its program to maximize minerals and metals recovery from primary and secondary domestic resources. Small-scale studies showed that use of 110 pct stoichiometric sulfur and 123 pct stoichiometric carbon, based on producing a 40-pct copper-iron matte, resulted in the recovery of 95 pct of the copper contained in the dust. Typical mattes contained less than 10 pct of the arsenic, 30 pct of the bismuth, and 45 pct of the antimony and tin contained in the dust. Matte was converted to blister copper by injecting up to 200 pct of the stoichiometric oxygen requirement over a period of 2 to 3 hours. Up to 76 pct of the copper contained in the dust was recovered as a crude blister copper containing about 2 pct arsenic, 0.5 pct antimony, and less than 0.1 pet bismuth and tin. A matte-white metal product resulted from carbothermically reducing dust with coal, lime, and silica. Up to 95 pct of the copper was recovered in the combined product.

Jan 1, 1981

The use of walk-through inspections, approvals and ad hoc investigations to ensure risk is kept within acceptable levels is reaching its limits of effectiveness. Further improvement in occupational health and safety requires a systems approach, and the use of Quality Management principles is an obvious basis for this. SafeGuard, a æbest practiceÆ model health and safety management system and audit criteria based on AS/NZS ISO 9001:1994, has been produced by the Department of Mines and Energy. Quality style audits of mine and quarry health and safety systems are now being carried out by the Inspectorate.

Jan 1, 1998

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By M Singh, R C. Steinhaus, J J. Rust

Metallurgical process control systems in mineral plants often employ state-of-the-art monitoring analysers in an attempt to optimise plant operations and enhance mineral recoveries. These systems are unfortunately invariably fed by simplistic ‘sampling’ designs consisting of various in-stream methods or pressurised probes. These are unfortunate compromises and provide a false picture of what a mineral flotation or other process can achieve. The situation is further aggravated by some manufacturers using misleading marketing to suggest discrete cross-stream methods for metallurgical accounting and unreliable continuous in-stream off-takes for control sampling and that they are of synonymous integrity.Reliable, absolute or representative samples are often absent in many modern day concentrator plants, due to compromises around sample taking, particularly in terms of delineation and extraction errors and thus leading to sample bias. For more reliable information from online analysers we need a continuous, but much more reliable sample taken, than is current practice.Online analysers require a fully proportional and continuous supply of sample for effective process control, otherwise maximised or benchmark recoveries will be nothing but a pipe dream. Large discrete cross-stream samples from mechanically less reliable equipment cannot be used as feed to online analysers, as it will negatively impact real-time feedback and efficient process control.It is possible to build correct sampling systems that could do both process controls online and metallurgical accounting at the same time. Multotec Process Equipment (Pty) Limited, in close association with experienced sampling consultant Francis Pitard, have jointly patented a concept to achieve this and which is embodied in the design of the unique Rotating Cone® Sampler (International Patent Application No. PCT/IB2016/057464). This versatile unit for dry and wet applications has high division ratios via two-step sampling and division.A prototype was built and tested to validate the design and levels of precision achievable when employing the unit to split dry mineral fines or even certain foodstuffs.CITATION:Steinhaus, R C, Rust, J J and Singh, M, 2017. Does process control sampling always have to be a compromise?, in Proceedings Eighth World Conference on Sampling and Blending , pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By R. S. Bigelow

Part 1.- Metal Mines Early experiments with mechanical loaders in metal mines were confined largely to machines of the shovelling type and generally air-operated. Although the first application of the scraper to metal mines dates back to 1910, it was not until about twelve years ago that it came to be used extensively. Generally, the scraper gives better results in metal mines than in coal mines, as degradation due to soft bottom and breakage are not factors, but it has a wide range of application and is successfully used in the mining of salt, potash, gypsum, zinc, copper, and a variety of ores, from soft material to hard chunky ore which settles compactly. Today, the scraper has replaced to a large extent the shovelling type of machine in metal mines. Scrapers have offered an inexpensive solution for the mucking problem and are now employed in most mining districts throughout the world. They are operated by labourers of all colours and degrees of skill. Each installation, however, requires individual study on the part of the mine mechanical department to determine the type of scraper, horsepower of hoist, and most economical speed of rope, as well as method of rope rigging. Unfortunately, the scraper has no power to select pay ore from waste and its suitability for use under circumstances which might require sorting of the ore can only be decided by a weighing of the economic factors involved

Jan 1, 1931

By Joël Kapusta

La pyrométallurgie du cuivre est essentiellement une chaîne de trois étapes successives d’oxydation préférentielle du fer et du soufre et des impuretés moins nobles que le cuivre qui sont contenues dans le concentré de cuivre issu de l’usine de concentration du minerai, aussi appelée concentrateur. La Figure 1 illustre la chaîne complète d’élaboration du cuivre depuis la mine jusqu’au cuivre pur. La voie hydrométallurgique traite le concentré par lixiviation, c.à.d. par dissolution en phase aqueuse à température typiquement inférieure à 100 ou 150⁰C, alors que la voie pyrométallurgique traite le concentré par fusion à température de l’ordre de 1200 à 1300⁰C.

May 2, 2024

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By J. Y. Hwang

The relationship between coal characterization and physical cleaning has not been well understood due to the complex nature of coal. Therefore, it is difficult to apply the results of coal characterization to predict and evaluate the performance of a physical separation (e.g. flotation). Eight U.S. bituminous coals were analyzed and studied petrographically in conjunction with washability and flotation tests. The results show that grindability correlates to ash and fixed carbon contents; liberation determined directly by petrographic techniques is close to liberation determined indirectly by washability; and an ideal separation efficiency can be determined by measuring the inertinite content and the washability separation efficiency using a heavy liquid with a density of 1.4. The ideal separation efficiency was attained for most coals by packed column flotation. The ideal separation efficiency can be used for comparing process technologies and process parameters.

Jan 1, 1988

Five conclusions that emerged from ADL's Contractor Noise Measurements Assessment done for the Bureau of Mines and the 7 December 1971 Bureau of Mines Contractors' Round Table Meeting in Boulder, Colorado were: ? a limited amount of good data has been obtained for characterizing the noise environment for electromagnetic (EM) coal mine operational/emergency communications systems; ? significant noise date gaps still exist; ? suitable instrumentation and data analysis methods are available for filling these data gaps; ? the immediate and most important data gaps should be filled by means of a timely field measurement effort that is purposely limited in scope and duration; ? this field measurement effort should preferably be carried out by a team knowledgeable and experienced in coal mine EM noise measurements.

Jan 1, 1972

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By E. B. Wright

THE property of Falconbridge Nickel Mines, Limited, is in Falconbridge township, approximately thirteen miles northwest of Sudbury. From the mine and townsite, a gravel road leads to Sudbury and a branch line of the Canadian National railway to Sudbury Junction. The ore deposit is at the southeastern corner of the 'Sudbury Basin'. It lies in a sheet-like mass, striking in an east-west direction, between norite to the north and greenstone to the south. The general attitude of the ore-body is vertical, but with frequent variations in dip of as much as 10° to the north or south. The deposit is very irregular in outline, the width varying from a few feet to eighty or ninety feet. In the vertical plane, rolls are frequently encountered. Gouge is very often present at one or both ore contacts. The norite to the north shows much jointing. The chief ore minerals are pyrrhotite, pentlandite, and chalcopyrite. The nickel content of the ore is usually double the copper content, average assays ranging from 2 to 2.5 per cent nickel and 1 to 1.5 per cent copper. The ore is of three main types: massive, breccia, and disseminated. The breccia ore, the most common type, consists of sulphides containing rounded inclusions of highly-altered country rock, which, in places, are so large that sorting is necessary in the stopes. In the norite, the breccia ore may grade into disseminated sulphides, which frequently are sufficiently concentrated for profitable mining. In places in the breccia ore, concentrations of solid sulphide masses occur. Until early in 1935, all mining at Falconbridge was by shrinkage scoping, but this method was found to be less and less suitable as greater depth was attained. When mining had reached the 1,000-foot level, ore drawn from large shrinkage stopes was found to have been diluted as much as fifty per cent by sloughing of the wall-rocks, caused by increased rock pressure and insufficient support. It was apparent that this method of stoping was un-suitable and -Mr. E. J. Martin was engaged to superintend the introduction of a method of cut-and-fill stoping.

Jan 1, 1938

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By Gregory M. Molinda

Large structural faults create serious ground control hazards, as well as adversely affect coal mineproduction. Two faults related to the Pine Mountain overthrust sheet in Buchanan County, VA, were investigated by the U.S. Bureau of Mines to determine their effect on ground control and to develop recognition criteria for prediction. Five underground mines encountering these faults were visited and mapped for structural information. This information, along with surface mapping, indicated that Pistol Gap and Keen Mountain Faults show right-lateral, strike-slip faulting and bedding planes slippage, which can be projected linearly and vertically. These fault zones are up to 200 ft wide, with coalbed offsets up to 18 ft vertically, coalbed swags (depressions) up to 15 ft, and roof falls up to 20 ft high. Recognition criteria include bedding plane slips, coalbed offsets, fault gouge, coalbed swag (depressions or synclines), and disturbed bedding. These recognition criteria will help an informed operator realize that many sudden coalbed discontinuities are related to larger geologic events (in this case thrust faulting) and can be projected linearly and vertically. Ground control strategies include mine designs that minimize fault exposure. Mining plans can be adjusted based on type and extent of fault movement.

Jan 1, 1989

By M G. Hawtin

The Rocklands copper project is a multilode, iron oxide copper gold (IOCG) + cobalt mineralised system located in the Eastern Fold Belt of the Mt Isa Inlier. Rocklands orebodies cover a range of oxidation zones from oxide, to supergene and primary. Each zone contains different economic minerals of interest. The supergene zones contain significant amounts of native copper and the primary zones are dominated by chalcopyrite. The juxtaposition of these oxidation zones and minerals make it an interesting mineralisation system.Current mine production sampling collects a nominal 3 kg drill chip sample from a 1 m composite, RC drilled interval. A site specific sampling procedure was needed to quantify introduced sampling error when taking grade control samples. Due to oxidation and mineralogical variation in ore zones we needed to develop a practically achievable sampling methodology that ensures minimum sample mass and sample error requirements are achieved to ensure ‘representative’ samples for all ore types.These issues are planned to be resolved using an experimentally derived method using principles from the Theory of Sampling. This method uses an experimental calibration of parameters K and a for Gy’s fundamental sampling error formula using a modified 32-piece sampling tree experiment to compile sampling nomograms for the primary and supergene ores. This paper demonstrates the process undertaken to improve the quality and standard of existing mine production sampling procedures at the Rocklands operation.Results indicate a sample mass of 5 kg for RC drill chips is appropriate for both the primary and supergene ores to achieve a fundamental error below 0.01 or 10 per cent relative error, which is slightly higher than the existing sampling protocol of 3 kg. An additional experiment is recommended to compile sampling nomograms using the exact laboratory comminution and mass reduction stage information to assess the use of a 3 kg sample. The results also indicate no changes are required to existing sampling protocols when sampling RC drill chips in primary and supergene ore at Rocklands.Sampling nomogram results also provide a useful ‘rule of thumb’ reference guide to other mining and exploration companies to help understand minimum sample mass requirements and sampling error during exploration drilling, resource evaluation and mining production stages when targeting similar IOCG mineralised systems. A sample mass of 5 kg is recommended when RC drilling similarly IOCG mineralised prospects and deposits in the Cloncurry area. Future test work is recommended when additional open cuts become active as well as including resource drilling drill core to provide better three-dimensional sample representivity.CITATION:Hawtin, M G, 2017. Minimum sample mass from reverse circulation grade control drilling at Rocklands copper project, in Proceedings Tenth International Mining Geology Conference 2017, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

JAmes E. Howard, Watertown, Mass.:—In connection with this paper, it is the desire of the Watertown laboratory to receive suggestions as to the lines of work and the particular direction along which the examination of the ingot-metal should proceed, and any suggestions so offered will be noted with care, and the tests conducted so as to embrace such features as it is thought desirable to have investigated. To me the question of structural continuity seems of para-

Jan 1, 1909

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012