Search Documents

By M. O. Serbousek

The load-transfer mechanics of fully grouted roof bolts in coal mines have been investigated in laboratory and analytical studies. The purpose of this Bureau of Mines research is to increase understanding and better interpret data from routine field pull tests and to develop a numerical model of a grouted bolt that can be used in a global computer model of a mine roof. Analytical studies using closed-form solutions and finite-element techniques were compared to experimental results. Laboratory work includes variation of bolt length, hole diameter, and grouL type. Pull tests were pel'fol·med on 4-, 2-, and I-ft bolts in holes of 1-and I-3IB-in diameters. Both polyester resin and inorganic grouts were used as the anchorage medium. Strain gauges were installed on the bolts at several locations to observe the rate of load transfer from the bolt through the grout to the rock mass when a force was applied at the bolt end using standard jack pull testing procedures and equipment. The average anchorage length of 4-and 2-ft bolts was 22 in. Grout type and hole size variations did not produce a significant effect on the rate of load transfer from the bolt to the rock.

Jan 1, 1987

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J Bassan

The mining industry is faced with imperatives to improve worker safety and productivity, adapt to skills shortages, high worker turnover rates, and provide more effective maintenance to new and ever more complicated plant and equipment. While more effective use of data combined with advanced analytics offers opportunities for improvement, providing this information to the worker in the field, in real-time, has proven expensive, cumbersome and ineffective. New capabilities are now emerging which address some of the limitations experienced to date. Augmented reality (AR) provides a means to overlay interactive digital information on top of the physical world. Combining the latest visual display, mobile computing and ‘track and trace’ technologies, AR provides an experience similar to a heads-up display in a fighter jet through small, personnel devices, such as smart phones or wearable glasses. Applying AR would allow a mobile worker to ‘see’ all relevant information for a given task, in the context of their physical environment and at the time they require it. The technologies behind AR are rapidly maturing and becoming available at a price point that is viable for commercial applications. It is anticipated that AR will become ubiquitous at a consumer level within the next five years. The specific challenges faced by the mining industry make it an ideal early adopter of AR technologies. This paper examines a number of use-cases of how AR can be applied to the mining industry and the benefits that can be realised. The paper will identify areas of further work and viable opportunities for immediate adoption within the industry.

Nov 22, 2011

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By William W. Odell

Certain gas-making processes are in use in Europe, particularly in Germany, which differ radically from those in common use in America. A number of them are of particular interest because they are different. The questions naturally arise: Are any of them applicable to the making of gas in this country and, if so, with what particular type of solid fuel? It is a fact that some of them were developed with consideration of a particular set of conditions and for the utilization of solid fuels available in Germany. The latter fuels, in certain characteristics, are unlike the high-rank fuels commonly used for making gas in the United States; therefore, in attempting to evaluate the various foreign- developed processes with regard to usefulness here, one must give attention to the particular conditions that will prevail in any specified case and also the characteristics and requirements of the process and generator under considera- tion. Three of the processes that were developed and put into commercial operation in Germany, and which have some characteristics in common, are con- sidered in particular in this publication; they are: 1. Lurgi pressure gasification process. 2. Winkler process. 3. The Leuna slagging-type producer-gas process. Each of these processes requires steam and oxygen as gas-maiding fluids. For a number of years, oxygen, has been used in a relatively pure state,. along with steam, in making gas in Germany, and many of the difficulties initi-. ally encountered have been overcome. Although it appears that oxygen recovered from air was first used in this manner as a method of utilizing a byproduct in a plant that used the nitrogen complement in the manufacture of ammonia; more recently, the oxygen was made particularly for the purpose. The fuels - brown coal or lignite used in processes 1 and 2 were not suitable for use in the older and commonly used intermittent-type water-gas generators, and it was necessary, therefore, to devise a different process for gasifying them. A gas of higher heating value than producer gas, was desired, and the use of oxygen (not air) along with steam made possible the production of the desired gas without nitrogen dilution, which characterizes producer gas. Operating data presented herein are based upon observations by, members of the Technical Oil Mission at plants in Germany, on records, and on information vocally given to members of the lässion, including the author, while visiting those plants, and they are believed to be reasonably correct; however, certain hasic observations, comparisons, and conclusions are. made by the author.

Nov 1, 1947

By Manqiu Xu, Andrew Lee, Frederick D. Ford, Cara Wercholaz

"Platinum-group minerals (PGM) typically occur in such low concentrations that quantitative mineralogical evaluation is difficult or impossible. The FEI MLA system used by Vale Base Metals Technology Development has been successfully employed to produce large PGM data sets that are statistically robust. The MLA Sparse Phase Liberation mapping routine produces false colored images that accurately document mineral textures, including intergrowths between various platinum group minerals and between PGMs and other tellurides and sulfides. MLA PGM search results can be used in conjunction with mineral chemistry to calculate platinumgroup element distribution to minerals and the MLA PGM images can be used to produce model grade-recovery curves.INTRODUCTIONThe platinum-group minerals (PGM) found in Sudbury area deposits have been extensively catalogued and reviewed by many authors including, but not limited to: Farrow and Lightfoot (2002), Cabri and Laflamme (1984; 1976) and Cabri (1981). The PGM list currently used has 12 minerals summarized in Table 1. As noted by Farrow and Lightfoot (2002), platinum-group minerals in Sudbury are dominated by tellurides, bismuth-tellurides and arsenides, with an absence of platinum-group element (PGE) sulphides or ferro-platinum alloys such as tetraferroplatinum - PtFe."

Jan 1, 2011

By J Deraisme, P Epinoux, O Bertoli

"Société le Nickel exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, with controls that are extremely complex at all scales, including lithology, oxydo-reduction conditions, mineralogy and multivariate geochemistry. In this context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: support effect – the exploration data set can only warrant the estimation of large panels of 20 × 20 × 3 m3 that are much larger than the selective mining units (SMUs) of 5 × 5 × 3 m3 information effect – the selection at the production stage uses estimates based on information that is much denser than that available for mine planning.The problem is rendered more complex in this type of deposit by the fact that the additive variables used for the estimation (metal accumulation and ore tonnage) are not the ones used to establish the selection at the mining stage (ie the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria not only involve Ni grades, but also other elements such as Al2O3, Fe2O3, MgO and SiO2.The solution presented in this paper is to construct an SMU multivariate simulation in the saprolitic horizon and construct an efficient post-processing aimed at producing multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model, which had its validity tested beforehand, is put to good use to mimic the selection process that happens at the mining stage by offering the ability to simulate a composite value located at random within each block.The paper also presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream (reserve optimisation and mine sequencing) phases of the project. The original version of the paper (see Deraisme, Bertoli and Epinoux, 2014) used an early version of the scenario reduction plug-in (named S2RM) built in Isatis® software, where measuring the distance between the initial set of scenarios and the reduced set was based on Ni only. The implementation presented here is for the second generation of S2RM, where measuring the distance between the initial and the reduced set of realisations is based on all study variables. The benefits of the measure adapted to the true multivariate nature of the problem are highlighted in this updated version of the paper.CITATION:Bertoli, O, Deraisme, J and Epinoux, P, 2014. Multivariate block simulations of a lateritic-type nickel deposit and post-processing of a representative subset, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 99–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

IN THE past, we have, perhaps, been somewhat careless in our furnace practice, in the use of high-grade material, lowering the production costs through demanding high-grade ores, increasing the size of units, and eliminating heat losses by collecting and returning unused heat to our furnaces. Further economies would seem to be possible through keeping out of the furnace those materials that appear to serve no useful purpose and carry with them heat that should be used in reduction operations. In the manufacture of pig iron, about three tons of inert nitrogen pass through the furnace for each ton of iron produced. This nitrogen serves no useful purpose in the chemical actions involved, but when discharged into the atmosphere it carries away a considerable quantity of heat. Can not this loss be eliminated, at least in part, through the use of more oxygen in the blast? Many metallurgical chemists, during the past 20 years, have stated that they thought it can and have urged that the plan be tried. Others have expressed doubt, not being able to visualize how more oxygen could be used in present practice; they have regarded it as impracticable, without trying to conceive of an entirely new practice based on a new reagent. That more experimental work has not been done is due to the fact that no cheap oxygen has been available, but the committee believes that there is strong reason to expect that, should a demand exist, 99 per cent. oxygen may be made at a cost not to exceed $3 per ton. The theoretical studies of the committee have indicated such marked economy by using oxygenated air in various operations that its members strongly recommend experimental work to verify the anticipated economies. The committee has developed plans for experimentally determining the effects of oxygen-enriched air on the operation of an iron, blast furnace. A furnace with a height of 30 ft. has been built and it is recommended that the plans be put in, effect as the first step in the research.

Jan 11, 1924

By R. Burger, M. Masukawa

Cato Ridge Alloys (CRA) is a joint venture company between Assmang of South Africa, Mizushima Ferro Alloy Company (MZK) and Sumitomo Corporation from Japan. Negotiations for the formation of the company started in 1992 with the joint venture agreement signed on the 19th September 1996. MZK was to supply the technical know how for the production of Medium and Low Carbon FeMn while Assmang was to manage the day to day activities of the company. Sumitomo Corporation was to act as facilitator between Assmang and MZK and, together with Ore and Metal are responsible for the marketing of the refined products. The conceptual design of the plant started in December 1996 and the first charge of molten high carbon ferromanganese metal was charged on the 19th January 1998. Problems experienced during the initial startup period were addressed resulting in substantial operational improvements. A build-up in the stock of fine metal was addressed through the development of a process to remelt the fine metal, the development of a market for fine metal and the upgrading of the crushing and screening plant to reduce the generation of fine metal. The mass yield from High Carbon Ferromanganese to Refined Ferromanganese was increased through the implementation of statistical process control, changes to the blowing patterns and the development of a sampling device for taking samples during the process. Converter refractory consumption was reduced. This was achieved on the converter by improving the cooling of the converters with the installation of cooling fans and cooling fins. The heating schedule of the converters was changed for improved refractory life. Production schedules were modified to allow cooling of the refractory between low carbon erromanganese charges. Additional changes made to improve operations were: ? Changing from mehanite casting trays to metal fines beds. ? Installation of sonic horns in the baghouse to prevent the bridging of dust. ? Improved welding on the lance tips.

Jan 1, 2004

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Traité de l'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw jack is composed of the following pieces: I. The body or column B, Fig. 4 [Plate (1)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 2 3/4 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 21/2 inches (for very high veins this diameter may be in¬creased to 3 inches), and has on its top a wrought-iron plate, T,

Jan 1, 1873

By C. Thiart

Kriging is an interpolation technique for predicting unobserved responses at target locations from observed responses at specified locations. Kriging predictors are best linear unbiased predictors (BLUPs) and the precision of the BLUP is assessed by the mean square prediction error (MSPE), commonly known as the kriging variance. Both the BLUP and the MSPE depend on the covariance function describing the spatial correlation between locations and on specific parameters. The parameters are usually treated as known, whereas in practice they invariably have to be estimated and the empirical BLUP (that is, the EBLUP) so obtained. The empirical or estimated mean square prediction error (EMSPE), or the so called ?plug-in? kriging variance estimator, underestimates the true kriging variance of the EBLUP, at least in general. In this paper five estimators for the kriging variance of the EBLUP are considered and compared by means of a simulation study in which a Gaussian distribution for the responses, an exponential structure for the covariance function, and three levels of spatial correlation ? weak, moderate, and strong ? are adopted. The Prasad-Rao estimator obtained using restricted or residual maximum likelihood (REML) is recommended for moderate and strong spatial correlation and the Kacker-Harville estimator for weak correlation in the random fields.

Jan 1, 2014

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By G. L. Mowrey

One critical element of the U.S. Bureau of Mines (Bureau) autonomous mining research program is the development of a reliable coal interface detection (CID) system. Several candidate CID concepts currently being investigated by the Bureau include vibration, passive infrared, radar, and natural gamma radiation (NGR). To establish which CID sensor technologies need to be developed for a given seam, coal and adjacent rock samples (i.e., immediate roof and floor) are being collected from selected major coal seams in the U.S. and are being analyzed in terms of NGR and other geophysical measurements. Results of the NGR measurements indicate that, in general, all shale and shale-like materials (e.g., drawslate, slate, and fireclay) have higher NGR readings than the coal seam. Consequently the NGR method appears to be a potentially useful CID tool, provided that the immediate roof and floor are both composed of a high percentage of shale-type material.

Jan 1, 1990

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972