Search Documents

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By M. Reuter, C. Schuffeneger, T. Seppälä, L. Holappa

Reaction kinetics of solid-state reduction of chromite pellets (laboratory made and industrial) and lumpy ore was investigated by the thermogravimetric analysis (TGA) technique. Carbon monoxide was used as the reducing agent, with the presence of graphite in proximity to chromite. The experiments were carried out at both rising temperature and constant temperature in the range of 1450 - 1550°C. Scanning electron microscopy was employed to observe and analyse the structure and composition changes of the chromite samples. For the lab-made chromite pellets, the effects of particle size and bentonite addition on the reduction behaviour were studied. The pellet with smaller particle size gave a higher reduction rate. Bentonite addition had slightly negative effect on the reduction rate. When reducing industrial pellets, temperature and CO flow rate had positive influence on the reduction rate. Reduction of lumpy ore took place slower than reduction of a pellet. In all samples, chromite reduction proceeded longer in the outer part of the sample than in the centre part. The porosity of the chromite samples was determined before and after the experiments. The porosity of lumpy chromite increased significantly during the reduction. However, the porosity of lab-made chromite pellet decreases due to sintering effect. The reaction mechanism is discussed on the basis of experimental results and earlier investigations.

Jan 1, 2004

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002

By J. A. Sekhar

Solidification processing/casting is increasingly being adopted as the preferred manufacturing technique for the fabrication of net shaped complex geometry components. Modeling of solidification processes is important both for design purposes as well as for understanding the physics of morphological evolution of the solidification microstructure. A fundamental aspect of such modeling involves the precise understanding? of heat transfer through the two phase solid/liquid region. A scheme to do this will be presented where the nonlinearity of the fraction liquid with change in temperature can be incorporated into the numerical calculations. The importance of properly accounting for the non-linear mushy zone will be discussed. Typical processes like squeeze casting and electromagnetic stirring will be discussed to illustrate how precise modeling of the solid/liquid region can aid in the calculation of accurate heat transfer coefficients for these processes.

Jan 1, 1990

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

The evolution of surface mine layout configuration is a function of the schedules and sequence of material excavation within the optimized layouts. The production schedules and sequence of materials movement from multi-bench and multi-face operations are difficult to plan and execute. However, the ability to maximize the profit or net present value of an orebody is largely dependent on the mining schedule. The mining schedule will determine the life of the mine, the projected cashflows, and the investment requirements over the mine life. The pit geometries, pit expansion rates and the periodic volume of materials from different benches in a multi-bench, multi-face open pit mine determine the equipment requirements. The volume of materials excavated, as well as pit layout changes from circular and elliptical geometries of an oil sands mine were modeled using analytical geometric and parabolic partial differential equations (PDEs) and solved within Matlab. The results show that the geometric values are almost the same as those obtained from PDEs for different pit configurations. The economic analysis shows that both the current mining system (CMS) and the cyclic excavator conveyor belt control system (CycEx CBCS) are viable with high NPV (= $3.20 × 1010), PI (> 19%) and IRR (> 29.02%) with short discounted payback periods (= 3.24 months). The CycEx CBCS option is more economic than the CMS option. Its NPV is 1.27 times that of the CMS option. The PI and IRR for the CycEx CBCS option are respectively 2.24 and 1.13 times that of the CMS option. As well, the CycEx CBCS option has almost half the DPBP of the CMS option. The CMS option has an operating cost of $1.386 per tonne ($2.774/barrel) while that of the CycEx CBCS option is $0.779/tonne ($1.558/barrel). These results show that the CycEx CBCS option is the better option for mining companies working on oil sands deposits to invest in.

Jan 1, 2011

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By G. I. Mathieu

Research and development studies were carried out at the Canada Centre for Mineral and Energy Technology to produce a synthetic forsterite sand from asbestos tailings for Les Sables Olimag Inc. The National Research Council of Canada also supported and collaborated to the project. Theoretically, the technological approach consists of a heat at over 1300°C; however, the process without additive would result in the production of an enstatite-rich product (MgSiO3) having a fusion temperature less than 1600°C. The purpose was to foster the formation of forsterite (Mg2SiO4), a more refractory compound. The fabrication of the forsterite product requires pre-agglomeration of serpentine-MgO with a binder, which is stable at high temperature, to prevent the loss of the powdered magnesium oxide as dust in the kiln off gases and to maintain the mixture homogeneous during the process. Characterization of the end products with respect to mineral composition and thermal resistance are described. The synthetic forsterite in sand form was tested with success under a bath of liquid steel maintained at 1700°C for up to two hours. The advantages of the new sand and its potential applications will be reviewed.

Jan 1, 1992

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By James W. Ballard, H. H. Schrenk

"The X-ray method of quantitative determination is advantageous because it permits determination of compounds rather -than ions or elements; for example, the direct determination of quartz in silicates,4/,5/,6/ The method also takes into account the finest particles of a sample, which may be lost in wet chemical methods because of solubility or in petrographic methods because of limitation of the microscope. The sample is usually reduced to a powder and is easily prepared,7/ only a few milligrams of material being necessary. The sample and its chemical composition are not destroyed and may be used for further analysis by X-ray diffraction or by other methods.This paper presents in detail some of the more essential problems that arise in the application of X-ray diffraction to quantitative chemical analysis, Photometric measurements are discussed in connection with line intensities and the choice of X-ray film. The internal standard method, successfully used in spectrographic analysis, is applied.Copper K-alpha X-rays from a demountable research-type X-ray tube were used with a camera of 20 centimeters radius with a cast-lead-slit collimating system. A combination of a tilted wedge and a lead-slit collimating system permitted irradiation of a large amount of sample with X-rays. This tended to minimize errors due to possible inhonogeneity of the sample, to decrease the time of exposure, and to keep the lines on the X-ray film to a minimum width. There was sufficient dispersion of the lines for satisfactory analysis of most samples. Power was furnished the tube by a. source of constant high potential consisting of a synchronous motor generator furnishing 500-cycle power to a 100-kv. transformer, rectifying valves, and a condenser filter circuit. The X-ray tube was operated as a gas-type tube at 35 kv, and 20 ma,, the exposure times varying from 1 to 2 hours. The constant output of X-rays from the tube, indicated bar an exposure meter built for the purpose, was satisfactory.The recording microphotometer8/has been described. It was found preferable to a nonrecording instrument for measuring blackening of lines above a background on X-ray films. This background, which usually occurs, is sometimes complicated by numerous peaks from lines of complex diffraction patterns. is microphotometer record of the pattern, therefore, facilitates the location of the background 'and the measurement of the heights of the peaks and thus contributes to the accuracy of a determination."

Jun 1, 1946

By Oren C. Baptist, Carlon S. Land, Eliot J. White

The water sensitivity of the oil - gas - producing sandstones in three fields in the Patrick Draw area of southwestern Wyoming was estimated by laboratory testing . The tests used to estimate sensitivity , which is a measure of the loss of well productivity if the producing formation is invaded by fresh water , are : Porosity ; permeability to gas , water , and brines ; saturation characteristics with air displacing water from the samples and by mercury injection ; and identification of clay minerals by X - ray diffraction . Laboratory results indicate that the degree of water sensitivity of the sands in the Patrick Draw, Table Rock , and Desert Springs fields vary , in that order , from moderately sensitive to highly sensitive . The main cause of the sensitivity appears to be the movement of fine particles in the pores , but the swelling of a small amount of an expandible clay mineral may also contribute to the permeability reduction observed in the samples . Laboratory results further indicate that the permeability of the sands to fresh water is seriously reduced if they are first flushed with sodium chloride brine ; calcium chloride brine is less harmful to the sands than sodium chloride brine . The low original permeability of the oil sand in the Patrick Draw field , together with its moderate sensitivity , indicate that the rate of water injection for the secondary recovery of oil will be low . Limited field experience in two pilot - injection wells confirms this prediction .

Jan 1, 1964

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

The 112th Annual National Western Mining Conference (NWMC) hosted by the Colorado Mining Association (CMA) drew some political heavyweights, if by voice only, into the fray of two of the hottest topics that the mining industry is currently facing ? climate change and the new energy economy. A changing political landscape in Colorado, as well as in Washington D.C., has given rise to questions about the economic future of the United States and the mining industry?s role in that future. While there has been a recent push away from traditional energy sources to a ?new energy economy? that is rich in renewable energy sources such as wind and solar, the NWMC?s agenda emphasized the role that minerals will play in new energy technologies. The conference was also full of talks about the industry?s role in reducing the United States? reliance on foreign oil and other mineral commodities. To that end, an impressive lineup of speakers were invited to attend the three-day conference Feb. 8-11, in Denver, CO. Unfortunately, Mother Nature had other plans and three of the four headliners, including Denver?s mayor and Democratic candidate for governor of Colorado, John Hickenlooper, were unable to get to the conference because of a massive blizzard on the East Coast locked them in Washington, D.C. However, with modern technology, a full auditorium heard presentations from Hickenlooper, National Mining Association (NMA) president and chief executive officer Hal Quinn and Glenn Kelly, vice president, government affairs for NMA. Republican candidate for governor of Colorado, Scott McInnis, did speak to the crowd in person.

Jan 4, 2010

By L. Connolly, F. R. De Luca

"Rubber liners at Denison Mines Limited are used in 10 1/2x 24' low discharg0 pebble mills. These were originally 10 1/2 x 13 Dominion overflow type ball mills. Experience here shows that the wear of rubber and ni-hard lifters is approximately the same in the feed end half of the mill, while the wear of rubber lifters is much greater in the discharge half. The wear of rubber plates is considerably less than white iron in the feed end half of the Mill and slightly more in the discharge end half of the Mill. Rubber components are lighter to handle but their installation is time consuming. This leads to the conclusion that a combination of ni-hard lifters a~~ rubber plates is the most economical compromise in Denison's case, for the Mill. Rubber discharge grates are superior to steel grates, while steel feed end liners are superior to rubber.The Use of Rubber Mill Liners at Denison Mines LimitedGrinding is done in two identic0al circuits each consist-ing of one 10 1/2 x 14' Dominion overflow rod mill, two Dorr Oliver quadraplex rake type classifiers, two 10 1/2 x 24' Dominion low discharge grate pebble mills and ancillary pumps and conveyors for pebbles. There is one centrally located distributor box that receives the discharge of the 4 pebble mills and splits it out to the classifiers."

Jan 1, 1974

By C. Feng, W. Song, B. Moudgil, P. Zhang, W. Xiao

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserves in Florida contains too much dolomite to process using the current industry practice. The FIPR Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered with three feasible options. Optional 1 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 2 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20-40%. Option 3 is a gravity separation technique using an innovative separation jig, and may well be the ultimate solution to the problem. INTRODUCTION Magnitude of the Dolomite Problem With the depletion of the higher grade, easy-to-process Bone Valley deposits, the central Florida phosphate industry has moved into the lower grade, more contaminated ore bodies from the Southern Extension. The phosphate deposits in the Southern Extension may be divided into two zones: an upper zone and a lower zone. The upper zone is readily processable using the current technology, but the lower zone is highly contaminated by dolomite. Geological and mineralogical statistics (Hassan and Bogan, 1994) show (Table 1) that more than 50% of the phosphate resource would be wasted if the lower zone is bypassed in mining, and about 13% of the resource would be wasted if the dolomitic pebbles in the lower zone were discarded.

Jan 1, 2019