Search Documents

By D. F. Malan

In deep level hard rock mining the rheological behaviour of the rock is important as time-dependent aseismic processes can lead to a stable dissipation of energy thus reducing violent outbursts. Underground closure measurements, observations of time-dependent fracture formation and siesmic data indicate that the rock in deep South African gold mines shows significant time-dependent behaviour. The objective of this work is to quantify the time-dependent rock behaviour for laboratory specimens and underground conditions. Laboratory experiments indicated that lava and quartzite specimens undergo measurable creep strain at stress magnitudes below the failure stress. Quartzite is however prone to more significant creep at lower stress levels. A viscoelastic analysis showed that laboratory creep results can not fully explain the behaviour observed underground. The in situ behaviour is governed mainly by the rheological behaviour of the fracture zone and the resulting time-dependent formation of new fractures. A viscoplastic discontinuity model implemented in a boundary element program is used to simulate this behaviour.

Jan 1, 1997

By Suthan Pooranampillai

Verification of drilled shaft resistance is primarily obtained through the use of different load testing methods. Procedures utilized include conventional top down static loading, the Osterberg load cell (O-cell) test and dynamic tests such as the Statnamic method. The O-cell test provides a means of obtaining separately the base and side shear resistance behavior of drilled shafts (cast-in-drilled-hole). Alternatively, the Statnamic load test method enables the engineer to derive base and side shear behavior separately, based on measurements of load, accelerations and strains along the length of the shaft. However, due to time and cost constraints these tests can only be performed on selected shafts within a project. Post grouting of a drilled shaft base embedded within a cohesionless material, with a low mobility compaction grout, will essentially pre-load the shaft base soil against the side shear and self-weight in much the same manner as an O-cell load test (when the load cell is placed within the base vicinity). Therefore, successful post grouting of a drilled shaft would enable verification of both shaft side shear and base resistance simultaneously on each and every shaft it is carried out on. Additionally, such post grouted shafts display stiffer load-displacement response during subsequent downward, superstructure induced, loading compared to ungrouted shafts. Verification of resistance on each and every shaft through the use of post grouting will allow an increase in resistance factors (reduction in safety factor) used in the design. Two 6 ft. diameter drilled shafts were constructed in Fredonia, WA, for WSDOT, each with an approximate length of 52 ft. The shafts were terminated within medium dense poorly graded silty sand. Statnamic load testing of the shafts indicated maximum derived static side shear and base resistances of 2545 kips and 507 kips (1.6 in. displacement) for shaft One and 2466 kips and 212 kips (1.4 in. displacement) for shaft Two. Shaft Two was subsequently grouted, with a low mobility compaction grout. Shaft base mounted total earth pressure cells measured a maximum sustained pressure of 55.44 ksf during the compaction grouting operation. Shaft displacement reached 0.65 inches in the upward direction at termination of grouting. Comparison of grouting data with initial load test information indicates that properly instrumented post grouting verifies shaft base and side shear resistance. In addition, these grouting induced resistances were much higher than design values supplied by the engineer using conventional resistance factor design. Large scale laboratory testing also shows that base grouting verifies higher soil resistances than permissible in conventional design.

Jan 1, 2010

By J. C. Taylor

The Rhodax inertial cone grinder, designed by France?s FCB Group Fives, is the result of three years, theoretical and mechanical research in the field of compression grinding by the research staff of FCB?s CRM minerals research centre. A number of potential uses have been assessed and will be discussed in the paper. The crusher is an inertial grinder that works on the pressurized bed fragmentation principle. The fragmentation force is caused by the rotation of unbalanced masses rather than by an eccentric mass, as is the case in a conventional crusher. This makes it possible to achieve very high reduction ratios. By controlling the speed of rotation of the unbalanced masses, the grinding force can be modified, thus changing the product size distribution. The paper describes the machine layout, operating principles, control parameters and will briefly describe the results obtained on reef, waste and ROM reject pebbles. Some comparisons are made with conventional crushing.

Jan 1, 1998

The HB 2500 hydraulic breaker attachment from Atlas Copco Construction Tools features Krupp percussion technology and a service weight of 2,500 kg (5,512 lbs). This makes it ideal for demolition, tunneling, trenching, foundation work, rock mining and secondary breaking. Suitable for carriers in the 29-to 43-t (32-to 47-st) weight class, the HB 2500 accepts maximum hydraulic flow of 219 L/min (58 gpm) at 18 MPa (2,610 psi) of pressure, and delivers an impact rate of up to 550 blows per minute. The HB 2500 features PowerAdapt, a new system that automatically shuts down the breaker in the event that it receives excessive oil pressure from the carrier.

Jan 1, 2006

By J. Hansen

This paper has been written for presentation during the Open Pit Mining Session at the SME Annual Meeting and Exhibit, Denver, Colorado, February 26 to 28, 2001. The paper addresses the application of automated monitoring of electric rope shovels to improve performance and blasting technique.

Jan 1, 2001

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Y. Miron

'This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, g the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2).

Jan 1, 2010

Jan 1, 1970

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By C. H. Mathewson

CONSIDERABLE progress has been made during the last few years in analyzing the action of plastic deformation in metallic crystals. This is due largely to the development of X-ray spectrographic methods for studying changes in the orientation of single crystals, or of conglomerates, as they occur during the process of plastic deformation, but partly to the widespread knowledge of suitable technique for preparing large (single or variously combined) crystals for direct crystallographic observation under stress or in various conditions of strain. These two methods of studying changes in the crystalline structure of metals may of course be used in conjunction with features of mutual support, but unfortunately the advantage of direct crystallographic observation is lost when we proceed to the study of severely cold-worked structures, owing to the occurrence of real or apparent crystalline discontinuities which become more and more complicated as the amount of plastic action increases. Furthermore, the X-ray methods do not appear to be adequate, at least in their present stage of development, to fix definitely the character of structural alteration in the parent crystal lattice by plastic deformation. The principal question at issue concerns the nature of the crystalline particles that remain after plastic deformation. These are generally known in our American metallurgical literature as crystalline fragments,' and they seem, indeed, to diffract as individuals causing the Hull pattern of a severely cold-worked metal to resemble the pattern of a fine powder,2 with certain features of preferred orientation among the particles deter- mined by the manner and intensity of cold working. We must freely concede that there are conceptions of lattice alteration, apart from that of simple fragmentation, which would account for an increasing number of lattice positions according to X-ray spectrographic observation as the degree of deformation increased.

Jan 1, 1927

By F. R. Lee

When the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mines. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers ill the design of many types of electrically operated machines and devices used in underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability y of the latest equip¬ment for safe use underground.

Jan 1, 1964

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By L. A. Jordan, D. van Vuuren

A two-dimensional finite difference model has been developed to describe the reduction of kilogram quantities of dehydrated phosphogypsum. The model’s scope has been limited to focus on the heat transfer and reactions that occur within a mass of material contained in a vessel inside a furnace rather than also including the effects of heat transfer to the vessel. Changes in the heat transfer properties (k, ρ, and Cp) are incorporated as the composition of the mass changes as the chemical reactions progress. The model is validated against experimental data, with samples heated to 1000°C at 3°C min−1 while purging with nitrogen gas. A sensitivity analysis of model predictions to the pre-exponential factor of the reaction rate constant of the main chemical reaction and the thermal conductivity of the powder bed indicated that, at the envisaged process conditions, the behaviour of the system depends much more on the rate of heat transfer than on the rate of the chemical reaction. The model demonstrated a significant increase in accuracy when the thermal conductivity was modelled to increase linearly with temperature compared to assuming a constant value.

Oct 1, 2022

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

By B. Simonian

"The Mount Milligan mine, located in central British Columbia, began operation in September 2013 with a design nameplate capacity of 62,500 dry metric tonnes per day, using a conventional SABC grinding circuit followed by bulk sulphide flotation. Over the last few years, many changes have been implemented in order to debottleneck and optimize the comminution circuit to meet and exceed the nameplate design capacity as well as improve the metal recovery of the flotation circuit. This paper discusses changes, grouped into mechanical modifications, projects, and operational changes. The implementation of these changes as well as ongoing challenges and potential solutions will also be discussed.INTRODUCTION The Mount Milligan mine began production in the fall of 2013. It is a conventional truck-shovel open pit gold and copper mine and concentrator with a 62,500 tpd design capacity copper-gold flotation processing plant. The average head grades for the life of mine are 0.18% Cu and 0.39 g/t Au. At full capacity, the mine produces an average 400 dry tonnes per day of copper-gold concentrate containing approximately 21.5% Cu and 50-60 g/t Au. Current mine life is 21 years. This paper will discuss a selection of the operational, engineering, and administrative changes that have been made at the site since the publication of An Update on Reaching Nameplate Throughput and Continuous Improvement at Mount Milligan (Yue, 2017). PLANT FLOWSHEET CONFIGURATION Run-of-mine ore is crushed through a 60-110 gyratory crusher to a top size of seven inches. Up to 100% of the gyratory crusher product is diverted to the secondary crushing circuit by a moveable gate. The material diverted to the secondary crushing circuit is fed to a vibrating double-deck screen. The screen oversize is placed on a surge pile and reclaimed by four vibrating feeders to feed two 1250 kW standard head cone crushers in open circuit. The screen undersize is combined with the crusher discharge and returns to the conveyor feeding the coarse ore stockpile along with primary crusher product that by-passes the diverter gate."

Jan 1, 2019

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976

By C. Webb, M. A. Tuck

This paper describes the application of a cable disc elevator to continuous lift ore vertically from underground mines. Application of this system requires the tensions developed within the cable must remain within the carrying capacity of the cable including applicable safety margins. A critical element occurs at starting the system when it is fully loaded which requires the force developed by the system to exceed the static friction forces. This paper describes the laboratory rig developed to investigate the static friction forces. Details of the results of tests on three different ores for both dry and wet conditions are given. These results are discussed.

Nov 19, 2020

By Hennessy F. L

It is generally recognised that slags are active participants in pyrometallurgical processes, and not merely inert liquids which must be produced. to effect separation of gangue material in smelting, or of impurities in refining. The importance attached to slag-metal reactions in steelmaking is shown by the numerous investigations in this field. However, there are still many important reactions of slags which require explanation. In this paper some new aspects of the reactions of slags will be discussed, as far as possible quantitatively.FREE AND COMBINED OXIDESMetallurgical experience indicates that variations in the composition of slags produce changes in the chemical behaviour of the various components. These variations have been generally ascribed to changes in the proportions of free and combined oxides, i.e., compounds have been assumed to be present in the liquid slag.Considerable support for this view has been adduced from the existence of compounds such as metallic silicates, phosphates, etc., in the solIdified slag. However, this does not imply that such compounds necessarily exist in the molten slag.The most direct evidence as to the nature of molten slag is to be obtained from a study of the liquid state. In...

Jan 1, 1950