Search Documents

By Marcello M. Veiga

Informal gold mining operations in the Amazon emit about 100 tonnes of mercury annually because of poor amalgamation practice. Lack of information and the complexity of mercury transformations hinder effective action to prevent such pollution and/or monitor its extent. In the past, mathematical equations have been formulated to deal with the correlation of natural variables and mercury in biota but often, the error range is too great to provide useful models. Projection of physico-chemical variations in an environment subjected to mercury emissions onto the extent of bioaccumulation is fraught with many uncertainties and unknowns such as internal correlations between variables and the site-specific nature of biota contamination. Often assumptions about closed systems are invalid when applied to natural environments. This work presents a heuristic approach to this problem in which amalgamation methods and natural variables are dealt with using an IF-THEN rule-based system that concludes about levels of emission and risk of bioaccumulation. The system is able to handle uncertain or vague data and yet still provide useful output. Belief in mercury oxidation or dangerous conditions are examined using Fuzzy Logic techniques and Inference Equations. These belief levels are derived from thermodynamic equilibrium data together with field observations of natural variables. This procedure can reduce the need for sophisticated analytical equipment and can provide information and diagnosis to non-technical people.

Jan 1, 1994

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By I. Gaballah

Jarosite contains up to 15 % of heavy metal compounds 'HMC'. The current waste disposal methods will not be allowed in the near future due to new environmental regulations and pollution risks. For these reasons, thermal treatments of raw or decomposed jarosite, in controlled atmospheres, were investigated. The aim of these treatments is to decontaminate the jarosite and/ or to recover the HMC for recycling. According to physico-chemical characteristics of the samples, the thermal treatments in controlled atmospheres N2, CO+N2 and C12+air lead to the extraction rate that vary from 93 to 98 %. Heavy metal compounds were separated by cooling the gaseous phase. The treatments' residue was almost free from HMC. Between 700 "C and 800 "C, the chlorinating treatment was successful of eliminating more than 97 % of HMC contained in four different samples.

Jan 1, 1999

By A. Schönecker, P. Y. Pichon, B. Kraaijveld, Y. Meteleva-Fischer

"Ribbon-growth-on-substrate is a casting method, which offers a possibility to control heat flow, nucleation and subsequent crystal growth at the liquid-substrate interface. This technology allows for low-cost and high throughput shaping of silicon sheets with controlled crystal grain size and orientation for use in solar cells. In this work, sheets of silicon- metal silicide composite materials were produced and their microstructure was studied. It was shown that depending on the relevant phase diagram and casting conditions, a micro/nano-sized eutectic structure of the casted sheet can be formed. Such composite materials possess properties promising for various applications in energy generation, storage and conservation. The advantages, potential and challenges of the ribbon-growth-on-substrate technique for production of composite sheet materials as well as novel areas of application for such materials are discussed.IntroductionThe Ribbon Growth on Substrates (RGS) process is well known in the solar industry as a process to produce multicrystalline silicon wafers. An industrial size pilot production line for continuous casting of silicon wafer was developed by RGS Development B.V. in the Netherlands (Figure 1). A comprehensive review of this technology and properties of the produced silicon wafers were reported by Schönecker et al [1]. The principle of the RGS process is explained in Figure 2. The relatively cold substrate extracts the crystallization heat from the liquid silicon in the casting frame. This results in the growth of a silicon ribbon (Vc) in contact with the substrate. When the substrate (Vp) is transported from the casting zone into the cooling section, the crystal growth stops, the wafer can be removed and the substrate can be re-used. Last few years large work was done on the industrialization and market development of RGS wafers for the solar industry. Part of this work was discussed by Schönecker et al [2]. Although there is still a good perspective on the middle and long term solar market for the RGS wafers, the current market situation was found to be unfavorable for new entrants."

Jan 1, 2014

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would be reduced at the new smelter to about a half of the sum of those from previous two 1 smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive offgases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By Donald Voit

"The reaction between zirconia/zircon, coke, and chlorine involves a slow reaction between the coke and the zirconia/zircon and a fast reaction with chlorine. Because of the fast chlorine reaction, the reaction rate for zirconia/zircon is nearly independent of chlorine concentration for most conditions. The reaction between zirconia/zircon and coke is particle size controlled and related to the degree of physical contact between the zirconia/zircon and the coke. Since particle-particle contact is critical, compaction of finely ground coke and zirconia/zircon produces the highest reaction rates. Uncompacted, coarse coke and zirconia/zircon has the slowest reaction behavior with static bed tests.SummaryZirconia reacts with chlorine in the presence of carbon to form zirconium tetrachloride, carbon monoxide, and carbon dioxide. A similar reaction occurs with zirconium silicate with the additional formation of silicon tetrachloride. The reaction rate depends primarily on temperature and the intimacy of contact between the zirconia and the coke. The reaction is multi-stepped with a slow reaction between coke and zirconia to form an intermediate that reacts rapidly with chlorine, causing the order of the reaction for chlorine to be near zero. Chlorination rates in the range of 1 µmole/hr/cm2 are seen for fluid bed reactors. Plug flow, and static bed reactors have reaction rates of the order of 1 mmole/hr/cm2, where the area is based on the zircon surface area in plug flow and fluid bed reactors and the boat cross sectional area in a static bed. Chlorination rates measured in zirconia/coke briquettes are higher with rates as high as 400 mmole/hr/cm2 reported. High chlorine diffusion resistance, not accounted for in the analysis of experimental results, has led to a lot of confusion in the literature interpretation of chlorination data.In general coke and zirconia/zircon particle size, coke and zirconia/zircon intimacy, coke to zirconia/zircon ratio, chlorine concentration, and temperature are important variables for chlorination. Decreasing the coke and zirconia/zircon particle size generally increase the reaction rate. The coke to zirconia/zircon ratio affects the reaction in a more complex way. Increasing the chlorine concentration generally increases the reaction rate, but the effect appears to be more related to the concentration dependency of diffusion than to its role in the kinetics. The reaction rate increases with temperature but the exact behavior is complicated by temperature effects on diffusion."

Jan 1, 2011

By D. J. Chaiko

Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution. We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS): In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.

Jan 1, 1996

By M. T. Thomas

Sufficient development of the X-Ray Photoelectron Spectroscopy (XPS), the Auger Electron Spectroscopy (AES), and the Secondary Ion Mass pectroscopy (SIMS) has made these instruments ideal for solving problems related to mineral processing -particularly gold ore processing. XPS can determine both the surface composition and chemistry of ores and tailings, and the various phases within either of them. AES can also determine surface composition with the further advantage of having greater spatial resolution so the surface chemistry associated with specific minerals in the ore can be identified. This identification helps to clarify why some minerals pass through a chemical process unaffected, while others can be successfully treated. SIMS has an elemental sensitivity from one to four orders of magnitude greater than XPS or AES which makes it useful for detecting the presence of some elements in very low concentration (parts per million).

Jan 1, 1981

By S. V. Cherty

The utilization of natural gas in non-ferrous industries during smelting and refining stages of copper , aluminum, zinc and lead was studied. The total amount of nonelectrical energy consumed in the production of zinc, copper, lead and aluminium, are 96.5% ,93%,92%, and 6 % respectively. It is calculated that 9.45 wt %of air of stoichiometric amount can be substituted by natural gas to the total air input in the nonelectrical energy utilization processes. The results showed that the non electrical energy may be substituted to an amount of 71 % ,52 % ,35 % ,32 % ,and 26% ,in the production of lead, aluminium (plates, foils) copper, aluminium, zinc, respectivelly. Similar calculations are carried out in terms of energy in Btu for the total production of non-ferrous metals in the U.S. It shows that 51.866~106 millions of Btu of nonelectrical energy can be substituted by 54.58~106 cu. ft of natural gas. Finally, the substitution of non electrical energy in terms of equivalent coal energy is discussed. 1t is shown that total non electrical energy is equal to 1.852 million tones of coal .If this 1.852 million tones of coal is replaced by natural gas, a total savings of 22.14 million dollars are achieved. The total or partial substitution of coal by the natural gas in the existing industrial processes and modification of redesigning the processes is discussed.

Jan 1, 1993

By Filippos Patsiogiannis

Laboratory size (4.5 kg) low carbon steel melts were deoxidized using Al and FeAl (33% Al), with and without synthetic fluxes, in alumina and zirconia crucibles. The dissolved oxygen, total oxygen, soluble aluminum, insoluble aluminum, silicon and carbon contents in the melt were determined as a function of refining time and temperature. It was observed that the reaction between aluminum and oxygen in solution closely follows thermodynamic equilibrium. Silica present in the alumina crucibles was found to be a source of oxygen for the melt, while this was not the case for zirconia crucibles. Reoxidation of the melt occurred through oxygen pick-up from the atmosphere. The extent of this reoxidation was found to be a function of oxygen content of the bath and the slag cover on the surface of the melt. The effectiveness of calcium-aluminate based fluxes in protecting the melt from the reoxidation and in increasing the rate of removal of inclusions was evaluated.

Jan 1, 1992

By Markku Rytkonen, Shaolong Chen, Ilpo Kylmäkorpi, Hannu Mansikkaviita

Though the Peirce Smith (P-S) converter is a traditional type of furnace, continuous improvement in its mechanical and electrical design is still Kumera's approach. Efforts are made particularly on the following aspects: converter head shape for easy fabrication and structural strengthening, oxidation air swivel joint for low pressure drop and low noise level, wind box for even air distribution to tuyeres, drive unit and its control for reliable and handy operation. These improvements have successfully been applied in recent P-S converter deliveries.

Jan 1, 2009

By Emmanuel N. Zevgolis

After the Krupp-Renn process was shown to be unsuitable for treatment of the Greek nickeliferous laterites, the LM process was developed. It involved roasting reduction up to metallic iron in a Rotary Kiln (R/K) and smelting in an Electric Furnace (E/F). Ferronickel (with 15% Ni) produced in the E/F, was upgraded to 90-95% Ni in an 02 converter. Raw Ni was then electrolyzed to pure Ni. The LM process was not applied for very long however, due to various problems. So, the Larco process was developed, i.e., pre-reduction in R/Ks, smelting of the calcine in E/Fs for ferronickel production (15% Ni) and enrichment to 20% Ni, in an O2 converter. Until now, many technological improvements have been invented and applied or adjusted to the process, which have made it a fully reliable and competitive one. sohe of the improvements were the invention and application of a new granulation process for liquid ferronickel, the modification of the existing R/Ks, E/Fs and converters and the design of new ones, and others that are described in the paper. Keywords: Ferronickel, metallurgy, laterites, LM process, Larco process

Jan 1, 2004

By Bhagyadhar Bhoi, Chitta Ranjan Mishra, Pravas Ranjan Behera

Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer’s Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

Jan 1, 2015

By A. J. Paul, K. O. Yu

"Today, foundries are moving towards the use of models and design tools to gain a competitive advantage in producing castings of high desired quality. This leads to a growing alliance between foundries, software developers and researchers seeking to model, visualize and understand the phenomena taking place during the casting process. In addition, there is a need to develop affordable techniques to produce parts in small lot sizes. This leads to the development of a Flexible Manufacturing System consisting of: (1) up-front computer-aided engineering; (2) computer integrated proto typing with solid freeform fabrication; and (3) fabrication of the actual mold and related equipment to cast the part.This paper discusses some of the developments that are taking place today in the areas of modeling the physical phenomena during the casting process as well as towards developing a Flexible Manufacturing System for producing cast parts. Areas that require most work involve prediction of defects and mechanical properties using simplified analyses. In addition, electronic data sharing for collaborative engineering between geographically dispersed team members is also discussed. Case studies are presented showing successes as well as failures.IntroductionCasting, one of the oldest forms of metalworking, has recently seen a flurry of developments in the area of solidification modeling. These developments have come about after the realization that, in order to stay competitive, foundries need to reduce their scrap rate and production costs, and increase casting quality. Even though this is not new knowledge for foundry engineers, the tools to help them achieve this goal are just being developed and put in place for use by foundries. Several state-of-the-art software packages are currently available to analyze the solidification behavior in complex shaped castings. These packages make use of several different approaches for solving the various problems associated with casting processes. The overall architecture of a comprehensive solidification modeling system is shown in Figure 1."

Jan 1, 1994

By Simon Lekakh, Von Richards, C. Hank Rawlins, Kent Peaslee

"Batch aqueous leaching and carbonation tests were conducted using industrial steelmaking slags to determine the effect of carbonic anhydrase enzyme as a catalyst. Calcium leaching is a strong function of particle surface area, and the extent can be expressed as a function of time and particle size. Carbonic anhydrase did not affect the calcium-leaching rate, however, it did catalyze calcium carbonate formation to achieve a neutralization time near the theoretical rate. Additionally, carbonic anhydrase modified the precipitate morphology due to accelerated particle nucleation. Time controlled tests in which the pH dropped to ~6 decreased the amount of carbonate produced, and this effect was exaggerated by carbonic anhydrase, while pH controlled tests (>8.5) exhibited the highest rate of carbonation. Because the leaching rate was ~50% faster than the carbonation rate, a further increase in the amount of carbonation may be realized by using carbonic anhydrase however pH must be >10.3.IntroductionSteelmaking slag contains high fractions of alkaline earth oxide based phases (i.e., CaO and MgO) that exothermically form carbonates. Thus, it is being considered as a means of permanent carbon dioxide sequestration. At current U.S. steel production rates, approximately 13-17 million tons/year of slag are generated from basic oxygen furnace (BOF), electric arc furnace (EAF), and ladle metallurgy furnace (LMF) processes [1]. BOF and EAF slag is used as high quality mineral aggregate or cement clinker, while LMF slag, produced at ~15% the rate of BOF and EAF slags, has limited use as blast furnace flux or acid mine neutralization with the majority going to landfill [2]. Based on slag’s chemical nature and immediate availability as a co-product from steel production, the steel industry initiated a project to investigate hydrous carbonate formation in steelmaking slag as a method of sequestering carbon dioxide emitted in steelmaking offgas [3]. The goal of this project is to determine the reactor parameters suitable for the design of an industrial system for treating steelmaking offgas with raw or minimally processed slag."

Jan 1, 2009